Search Documents

By W. Joseph Schlitt, William D. Southard, Bruce P. Ream, Lawrence J. Haug

The operation of Kennecott's Bingham Canyon copper precipitation plant, one of the world's largest, is described. This description includes a brief historical review of precipitation at Bingham and the general layout and operation of the present cone cementation facility. Current practices are based on results of studies undertaken to define improvements needed in each unit operation. These improvements were required to meet changing plant conditions and were implemented primarily within the constraints of the existing facilities. Specific unit operations included were the cone precipitators, the cone discharge thickener, the cone effluent settling basins, and the plate and frame filter presses. As a result of these improvements, loss of precipitated copper decreased and the degree of precipitation increased, raising copper recovery by 9 t/d. At the same time, iron consumption was reduced by 22.5 t/d. Problems in drying the cement copper were also overcome so that a product containing 12 - 15% moisture could be consistently delivered for smelting.

Jan 6, 1979

By William D. Southard, Joseph W. Schlitt, Bruce P. Ream, Lawrence J. Haug

The operation of Kennecott 's Bingham Canyon copper precipitation plant, one of the world's largest, is described. This description includes a brief historical review of precipitation at Bingham and the general layout and operation of the present cone cementation facility. Current practices are based on results of studies undertaken to define improvements needed in each unit operation. These improvements were required to meet changing plant conditions and were implemented primarily within the constraints of the existing facilities. Specific unit operations included were the cone precipitators, the cone discharge thickener, the cone effluent settling basins, and the plate and frame filter presses. As a result of these improvements, loss of precipitated copper decreased and the degree of precipitation increased, raising copper recovery by 9 t/d. At the same time, iron consumption was reduced by 22.5 t/d. Problems in drying the cement copper were also overcome so that a product containing 12-15% moisture could be consistently delivered for smelting.

Jan 1, 1980

By Robert S. Nichols

Fording Coal Limited's mine in the Rocky Mountains near Elkford, B.C. has produced 21.8 million clean tonnes of metallurgical coal from 1971 to 1980, inclusive. This production has come from several pit areas and required the removal of 149.1 million bank cubic meters of waste rock and overburden by truck-shovel and dragline operations. Waste dumps from 30m to 200m in height have been successfully constructed on natural slopes, generally between 10° and 26°. Design considerations for the dumps include foundation and soil conditions, natural slope angles and containment of weak overburden or rehandle materials. Dump control is maintained by monitoring the crest and the face of an active dump area. Crest movement is measured by extensometers locally termed "Spoil Monitors". When crest movement rates progressively increase above normal, dumping operations are temporarily relocated. Some unstable conditions and mass failures have occurred as the result of natural foundation slopes being in excess of 26°, failure of weak water saturated foundation soils or weak material being placed on the dump.

Jan 1, 1983

The Institute has prepared a list of Societies' publications, magazines, . etc., which were duplicates and were discarded at the time of the consolidation of the libraries of the three Founder Societies. These books will be disposed of about March 1, 1916 by the Board of Directors of the Institute through the Library Committee. If, meanwhile, members who have incomplete sets of these books, or for any other reason desire to secure some of them, they are asked to communicate immediately with the Secretary, as this is in unusual opportunity to secure books at a very low price. American Gas Light Journal, viols. 31 to 39. American Institute of Electrical Engineers, Transactions, vols. 5 to 26. American Machinist, vols. 3 to 20, 22 to 29. American Society of Civil Engineers, Transactions, vols. 2 to 10, 21 to 24, 26 to 33, 39 to 49, 52, 55, 58, 74. Index, viols. 1 to 21. American Society of Mechanical Engineers, Transactions, vols. 1 to 28. Index, vols. 1 to 20, vols. 1 to 25.

Jan 1, 1916

By LUDWIG VOGELSTEIN

WE are indebted to Mr. Barbour for his valuable contribution to the literature on copper statistics; it is to my knowledge the only intelligent attempt to throw light on a much misunderstood subject. If I should appear to criticize some of his findings and arguments, I do not want to leave the impression that I do not appreciate the article; I think Mr. Barbour has been painstaking, and even where one might not agree with his conclusions, he has opened our eyes and stimulated us in our search for the truth.' It might be well to define the term "secondary copper" and to make a few remarks about the origin and the reasons for the variation of the supply. Mr. Barbour has touched on these points, but not sufficiently to make them clear to those not in the business.

Jan 1, 1931

By G. P. Halliwell, C. R. Austin

The investigation described in this paper deals with the development of high-temperature alloys of the Konel series over a considerable period of time at t,he Research Laboratories of the Westinghouse Electric and Manufacturing Co. The word ''Konel" has been coined to designate a class of alloys which are essentially nickel-cobalt-iron with other elements added, usually in small quantities. Most of these alloys contain titanium, usually about 2.5 per cent. The main consideration related to strength at high temperatures but the thermionic characteristics of the alloys was also of considerable importance. It is, however, with the mechanical properties at elevated temperatures that we are herein concerned. Much attention has also been devoted to their age-hardening characteristics. There is little need to stress the utilitarian aspect of this subject, as it has been discussed frequently. Alloys exhibiting superior properties at normal or elevated temperatures rapidly find many suitable applications. There may be some question, however, as to what constitutes a "superior alloy," or an alloy that may have good service possibilities at high temperatures. The problem is complex and various means have been employed to predict the useful life that may be expected of a material. In recent years the "creep limitJ' has been used as the best means of evaluation. Such tests necessarily are prolonged and hence collection of data is very slow. In a general survey of many alloys therefore the creep test is not desirable and recourse must be had to much shorter time tests in order more rapidly to select alloys which appear to show promise. For this reason the present survey has been made using the high-temperature tensile test and a bend test developed by Howard Scott.' In the tensile test the conditions have been standardized for all tests, so that values obtained are at least comparable, one alloy with another, although the absolute values recorded merely indicate the mechanical properties at the given temperature under a definite rate of loading.

Jan 1, 1932

By George A. Laird

I. INTRODUCTION. THIS old and once famous district played, through its enormous production of silver and gold, an important part in the history of the State of San Luis Potosi. According to a pamphlet prepared under the direction of the Governor of the State, Sr. Don Blas Escontria, and presented to the visiting members of the Institute during the Mexican meeting of 1901, this district is situated 20 km. east of the city of San Luis Potosi, in a range of mountains of moderate height, extending 135 km. N. and S., and 16 km. E. and W.; and the mineralized area hitherto developed is about 600,000 sq. m. The history of the district,. as given by the record dated 1778, and formerly kept in the San Francisco convent, says that it was discovered in 1575 by Sr. Don Pedro Irarte, and adds that the city of San Luis Rey de Francisco del Potosi received its name (in allusion to the famous Potosi mines in Bolivia) by reason of the remarkable productiveness of its gold- and silver-mines in the first period of their exploration, during which they paid to the Crown, as " quintos " (the fifth part of the product), $97,000,000, as appears from the accounts of the royal treasury. The amount of the quientos paid during the " bonanza period " of 80 years was $72,000,000. The larger sum first mentioned probably represents a longer series of years. But either will suffice to indicate the great wealth of the mines. In 1663, the decadence of the industry began with the caving¬ in of several mines, concerning which the record of 1778, al¬ready cited, says, in substance, that on Good Friday one of the owners in the enterprise, in view of the unfavorable prospect of a lawsuit in which he was engaged, set fire to the timbers supporting the underground galleries and workings of the San

Jan 1, 1905

By F. H. Deily, D. S. Rowley, R. J. Howe

P. W. BRIDGMAN.-Owing to a misunderstanding, I did not see Dr. McAdam's and Dr. MacGregor's remarks on my paper on Flow and Fracture (Metals Technology, December 1944, Pp. 32-38), until after their publication. Both Dr. McAdam and Dr. MacGregor speak of my analysis for the stress distribution at the neck of a tension specimen as containing several assumptions; in particular, that the strain is uniform across the section of the neck, that there is no hoop tension at the periphery, and that the plasticity conditions of von Mises hold. As far as the mathematics goes, the situation is no different in this problem of plastic flow than in a conventional problem of elasticity. That solution is unique which satisfies the boundary conditions on the stresses, the stress equations of equilibrium, and in addition the constitutive equations connecting stress and strain in the elastic case, or a corresponding set of equations, of which the von Mises relations are a special form, in the plastic case. In the particular case of the necked tension specimen I have found that there is a solution satisfying the boundary conditions, the stress equations of equilibrium, and the von Mises plasticity conditions in which the strain is uniform across the section, and there is no hoop tension at the periphery. This is therefore the solution, and the uniformity of strain and vanishing of hoop tension at the periphery are to be described as discoveries, over which the operator has no control, rather than as assumptions. The only part of the solution that can properly be described as an assumption is the von Mises plasticity condition. With regard to this it is to be noted that the condition is needed only in a much weakened form, for the analysis uses the condition only at the neck, where the strain is approximately constant. Thus, in the extreme case referred to in a footnote of my paper (p. 37, Met. Tech. Dec. 1944) the actually measured strain across the section varies from 2.4 to 2.6. Obviously it is a much weaker assumption to postulate that the von Mises condition holds in the strain range 2.4 to 2.6 than to assume it to hold for the entire range of strain from o up to 2.6, which would be necessary if the solution applied to the entire tension specimen rather than to the immediate region of the neck only. Furthermore, it is to be commented that under the special conditions of this problem the von Mises condition becomes identical with the maximum shearing-stress criterion of plastic flow; this amounts also to a weakening of the restrictions imposed by the von Mises condition. Dr. MacGregor refers to actual experiments of his own in which the strain was found not to be uniform across the neck. It is to be emphasized, however, that these were experiments on bars of rectangular section, and that the nonuniformity established was a nonuniformity around the perimeter, not a nonuniformity from the surface toward the axis. My method of solution applies only to a circular cross section. It can be said that the solution that satisfies the boundary conditions, etc., would definitely not be expected to demand a uniform strain for noncircular sections. In discussing my results, Dr. McAdam uses a definition of "flow stress" different from mine, so that the immediate applica-

Jan 1, 1945

By C. H. Lieb

ONE astounding fact in the production of petroleum is the comparatively recent realization by producers that flowing production is the cheapest crude produced. About 1910 or even later, operators actually endeavored to get a producing well to pumping as quickly as possible after completion. A well was not really considered to be completed until it was operating on the pump. Remarkable progress has been made since then. It was not until about 1920 that producers began to take a serious interest in pressures and to think a little about proper methods of handling oil wells. Pressure gauges were installed, and records of pressures maintained, which was quite an innovation. Desultory experiments were made with tubing of different sizes, as well as experiments with placing the bottom of the tubing string at different levels in the well. Probably the first important departure from customary procedure was about 1926, during the Seminole development, when gas lift

Jan 1, 1936

[JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington) D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4, N. Y. BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 210 La Arcada Bldg. Santa Barbara, Calif. COWIN & CO. Mining Engineers and Contractors Consulting Shaft & Slope Sinking Appraisal Mine Development Reports Mine Plant Construction I- 18th St. S. W. B'ham, Ala., Phone 56-5566]

Jan 1, 1952

By Richard W. Bayley

The Atlantic City district encompasses several districts and has been previously called by different names, e.g., Atlantic gold district, Atlantic City-South Pass mining district, and Sweetwater mining district. The district is located in a terrane of folded and faulted early Precambrian metamorphic rocks which lies near the south end of the Wind River Range in Fremont County, Wyoming, Historically it is a gold district of little production, but today is an iron district of considerable importance. Gold was discovered in placer deposits about 1842 and in quartz-arsenopyrite veins about 1867, after which there occurred a mining boom lasting a few years. Minor, intermittent gold production from placers and lodes has continued to date, but the total production has probably not exceeded a few millions of dollars. Past lode mining was generally shallow ( in the oxidized zone), the deepest about 3 60 feet. The deeper, less oxidized and sulfide ores on the same lodes have not been explored. They appear to hold the only hope for future gold mining. Sedimentary iron-formation, similar to the Lake Superior taconite, occurs in the northern part of the district. Locally, where the ironformation is thickened by folds and faults, sufficient tonnages are present to be minable, as at Iron Mountain, where the U.S. Steel Corporation produces about 1.3 million tons of iron-ore pellets annually. Exploration of the iron deposits began in 1954, and the first ironore pellets were shipped to Provo, Utah in August 1962. Indicated reserves of iron-formation (about 30 per cent Fe) are reported to be about 300 million tons.

Jan 1, 1968

CONTENTS [The Nature of Strain Markings in Alpha Brass (paper by J. E. BURKE and C. S. BARRETT, Met. Tech. Feb. 1948. TP 2327). ......................... 2 X Ray Studies of Twinning and Untwinning in Magnesium Alloys (paper by J. B. HESS and R. L. DIETRICH, Met. Tech. Feb. 1948. TP 2328) ................ 11 ]

Jan 1, 1948

By AIME AIME

THE Board of Directors of the Institute has authorized the appointment of a committee to draw up rules of procedure under which awards can be made from time to time to petroleum engineers for outstanding contributions to the art of finding and producing oil and gas. These awards will 11e sponsored by the Petroleum Division and are the first recognition by any professional society of outstanding achievement in "oil mining." They will be in the form of either a gold medal, scholar- ship, or other suitable prize. The awards will be financed from the income of the Anthony F. Lucas Memorial Fund, which was started about fifteen years ago, shortly after' his death, by admirers of Captain Lucas.

Jan 1, 1936

By Alfred E. Hunt

By the death of Joseph Dame Weeks, past-President of this Institute, which occurred December 26, 1896, the world has lost an earnest and unwearied philanthropist; the Christian church, a zealous, active and consistent representative; the United States and the State of Penusylvania, a patriotic, pub-

Jan 1, 1898

INSTITUTE OF METALS DIVISION Ferrous and Nonferrous Physical Metallurgy (By-laws in Transactions, Vol 156, 1944) Established as a Division April 26, 1918 Walter A Dean, Chairman R. M. Brick, Past-Chairman Morris Cohen, Senior Vice-Chairman J H Scaff, Vice-Chairman Ernest Kirkendall, Secretary-Treasurer

Jan 1, 1952

Ferrous and Nonferrous Physical Metallurgy Established as a Division April 26, 1918 T A Read, Chairman O T Marzke, Past Chairman J H Jackson, Senior Vice-Chairman David Swan, Vice-Chairman D C Johnston, Secretary-Treasurer AIME, 29 West 39th Street New York 18, New York

Jan 1, 1960

Established as a Society February 26, 1957 John S Bell, President Wayne E Glenn, President-elect Basil P Kantzer, Past President R E Howard, Vice, President M B Penn, Vice-President Everett G Trostel, Treasurer Joe B Alford, Executive Secretary 800 Fidelity Union Bldg Dallas 1, Texas

Jan 1, 1959

By Stephen G. Wright

Jan 1, 1985

By John Freeman

THE tensile properties of steels at elevated temperatures have been studied by numerous investigators,1 primarily for the purpose of determining their suitability for structural uses. Tests with this objective have been confined largely to the temperature range of approximately 20° to 500° C., because of the rapidly decreasing tensile strength at the latter temperature. Tests have also been extended to higher temperatures for the purpose of determining the most suitable forging range. This temperature range is also of theoretical interest. The phenomenon of increased tensile strength and decreased ductility in the so-called "blue-heat" range, approximately 200° to 300° C., is well known. It was suggested to the Bureau early in 1926 that a study of the properties of rail steels in this temperature range might prove of interest in relation to the studies of transverse-fissure failures in rails. There were available from another investigation3 several new rails from several different heats made to approximately the same specification requirements, the complete manufacturing histories of which were known. It was decided to determine, at least in the preliminary series of tests, only the ultimate tensile strength, elongation and reduction of area, because of the difficulty, time and cost involved in determining the proportional limit and yield point at elevated temperatures.

Jan 1, 1930