Search Documents

By A. K. Sinha

The market for thermal coal has recently been growing rapidly and it is projected to continue to do so in the foreseeable future. Both the national and international markets often demand high-Btu low-sulfur thermal coal in order to minimize the cost of utilization and meet the environmental restrictions. High quality thermal coal can be prepared to compete in the utility market by desulfurizing the high-Btu midwestern coal and blending it with low-sulfur western coal which is usually low in Btu content. The methods that can be used for optimizing the coal preparation plant operating parameters for physically desulfurizing coal are presented.

Jan 1, 1985

HAVING previously described the metals to you, before I proceed any farther I do not wish to fail to tell you, as I promised to do in the first chapter on metals, what I have learned through experience concerning the semiminerals, although this may seem to you outside our proposed subject. Since these are not produced by Nature as all rock or all metal they are called semiminerals by speculative physicians. Many kinds of these are found; those that resemble rocks are earthy, very difficult to liquefy, and much more adapted for adorning paintings than for anything else. Those that liquefy with fire, like sulphur, antimony, marcasite, [22] calamine, zaffre, manganese, and others, resemble the metals almost like brothers. Some others are more watery so that they dissolve in water, although they are fairly dense, and are obtained and reduced to their, perfection by means of water. These are the salts, vitriol, rock alum, and saltpeter. To these, as a watery thing, belongs also quicksilver, as it is commonly called because of its motion. Although it appears. not only liquid, but very liquid, this is not at all similar in its effects to any of the above. Indeed, it retains its same being until its very form is consumed. Since the reasons for its effects are almost impossible to investigate, I do not intend to speak of them here or to enter now this maze of speculation, because I wish to make definitely clear to you what this quicksilver really is. Therefore, leaving aside opinions and disputes, I shall take only those of the said semiminerals that I know are useful. First we shall see the method by which the semiminerals can be found and then how they are to be extracted from their matrices. These, perhaps, have no less need of effort and industry than the metals since they are substances completely hidden in the rocks or in the earth. For this reason some of these that are sought are made use of by means of fusion after they have been mined from their mother mountains, and some others need to be disposed by a certain maturative corruption, now with moisture and coldness, now with dryness and heat, as with waters, rains, frosts, or long baking in the sun, with fire, or even with a strong reheating within themselves. Most of them can finally be brought to the desired end by means of solution with water and fire.

Jan 1, 1942

Discussion of the paper of Ralph Hayden, presented at the Butte meeting,. August, 1913, and printed in Bulletin No. 80, August, 1913, pp. 1443 to 1467. JOHN V. N. Done, Denver, Colo.:-Mr. Hayden has placed the metallurgical profession greatly in his debt .for this valuable paper. The importance of such a complete description of the research work on which is based the building of a plant to add at least 10,000,000 lb. of copper per year to the production of the Anaconda Copper Mining Co., at small expense, will be appreciated by all our members, and especially those who are facing similar problems. The information given in regard to the treatment methods discarded will be a great help to many workers, as it is often of as much importance to know what ? not to do" as what method to adopt. I Some further comment on the tests of the Dorr thickener may be of interest, as they have led to developments which I believe will prove of great importance. Before the Dorr thickener was installed, I had shown Mr. Laist reports from the Steptoe Valley concentrator, in which it was stated that one thickener 17 ft. in diameter was the equivalent in settling capacity of twelve 8-ft. cones, although the latter-contained double the surface area.. Mr. Laist, had made careful tests on the settling capacity of in 8-ft. cone on Anaconda slime, and we naturally expected the thickener would show a much higher capacity for equivalent area. When, is Mr. Hayden stated, the tests showed no increase, I realized that we were comparing it with a cone under test conditions, while the Steptoe results were based on operative conditions, find the explanation given by Mr. Waddell for the great difference had been, that " there is only one unit to watch instead of twelve, without the constant result of feed to twelve cones becoming unbalanced. Also the one 1 1/8-in. spigot used on the Dow requires no attention compared with the dozen 3/8-in. spigots of the cones.' I realized also as a. result of the tests that the total settling area required to handle the immense tonnage of the Anaconda company would be enormous, and very expensive in view of the housing required by Montana climatic conditions. After studying the matter over, I told Mr. Laist that I believed a thickener operating in a much shallower tank would have nearly the same capacity. I asked him to test it out in the same tank filled 3 ft. deep, and stated that if my idea

Jan 11, 1913

By William I. Watson

Problems encountered in beneficiating mineral raw materials become increasingly difficult as there is a shift to lower grade and more complex raw materials, and because of the economic need to strive for ever higher recoveries, higher grade products, and lower processing costs. Methods of attacking the many problems should include not only the familiar chemical and physical tests and equipment, but such techniques as X-ray analysis, infra-red analysis, differential thermal analysis, and the use of electron and X-ray microscopes. Many people in the mineral-treating field are unfamiliar with these newer methods and techniques. The differential thermal analysis method, in particular, does not seem to be very well known, even though it offers interesting possibilities in the study of many ore treatment problems.

Jan 7, 1959

By Oliver C., Ralston

THE following data were obtained during Tan exhaustive research into the possibilities of concentrating United Verde massive sulfide copper-zinc-iron ores by flotation. The composition of these ores approximates the following mineralogical analysis: 3 to 15 per cent chalcopyrite; 3 to 11 per cent marmatite (ferruginous sphalerite) ; 47 to 69 per cent pyrite; and 10 per cent quartz. The remainder is usually schist gangue. The sulfide minerals are finely dis-seminated; chalcopvrite and marmatite begin to be liberated on grinding at about 100 mesh, but complete liberation from gangue (pyrite in this case is considered a gangue mineral) is

Jan 1, 1935

By Roy J. Greenfield, Charles H. Stoyer

A geophysical survey was made in Kylertown, Pa., in an area where the ground water is polluted with acid mine drainage. Since acid mine water is a good electrical conductor, both direct-current electrical and electromagnetic loop methods were examined for their ability to determine the subsurface electrical conductivity structure and from this to imply the location of the acid water. Consistent results were obtained with the two methods and the interpreted subsurface resistivities were consistent with the electrical resistivity measured for water samples. It was demonstrated that fracture traces which act as conduits for ground water flow can be located with electromagnetic surveying methods. Thus geophysical methods for measuring subsurface electtrical resistivity can be used to advantage for monitoring the environmental impact on the ground-water system of acid mine water.

Jan 1, 1977

By S. K. Nicol, A. R. Swanson, J. C. Day

Addition of oil to a suspension of hydrophobic coal particles can influence its dewatering characteristics. An agglomeration process occurs in which coal particles are held together by negative capillary pressure at particle/oil/water contacts. Consequently, the units round which flow can occur are enlarged and this improves dewatering parameters such as drainage rate, solids recovery, and equilibrium moisture content. This paper discusses processes which attempt to use this principle, in terms of metallurgical and economic efficiency. The discussion is augmented by results of recent experiments on the effect of oil addition to centrifuges and vacuum filters.

Jan 1, 1980

By G. Carman Ridland

Front Range, Colorado: The majority of the rocks comprising the Front Range of Colorado are pre- Cambrian schists, gneisses, and intrusives which have been elevated to form part of the Southern Rocky Mountain physiographic province. The region is noted mainly for its production of gold and silver, but ores of tungsten, fluorspar, uranium, copper, and iron have been worked. Geological literature describes pitchblende and other radioactive minerals occurring at Jamestown, Boulder County; Central City, Gilpin County; and Lawson, Clear Creek County (fig. 1). These three adjoining counties cover most of the highly mineralized section of the Front Range which extends from James- town to Breckenridge. As far as the writer is aware, uranium has been found only in the portion north-east of Lawson.

Jan 1, 1950

By Arthur Phillips, C. H. Mathewson

During the past year considerable work dealing with the mechanical properties and microstructure following the anneal under uniform condi-tions of certain types of commercial rolled brass has been done in this laboratory. Since these experiments were conducted with the active cooperation of the Bridgeport Brass Co., involving free use of its product, and have thus furnished information which is characteristic of some of its special mixtures, full publication of the numerical relationships and comparative results encountered does not seem justifiable. Some of the more general features of this work are, however, available and it is our present purpose to use the material in question, along with some results of special tests, in discussing the characteristics of recrystallization as related to the degree of hardening by strain and the ordinary annealing variables. We desire to make acknowledgment of the many courtesies extended by Mr. Charles Ferry, Metallurgist of the Bridgeport Brass Co., and the value of his cooperation, which has greatly stimulated the study of brass in this laboratory. A clear and systematic presentation of the principal relations between temperature and time of anneal, the changing physical properties and microstructure and the degree of previous reduction by cold-rolling, was first made, in the case of rolled brass and copper, by the French engineer, C. Grard,' in 1909, although much fragmentary information of this general character had appeared earlier and the main facts involved were undoubtedly known to many brass specialists through their own private research. From this work, it appears that in the cartridge mixture (67 per cent. copper, 33 per cent. zinc) the properties imparted by cold-working within the limits, 13 to 75 per cent, reduction of area by rolling Original Area — Final Area 0.13 to 0.75), are not affected by anneal- Original Area " ing for a 50-min. period at any temperature below 200°C. At or in the

Jan 1, 1916

By W. L. Prehn, Adele Chambers, R. L. Slobod

The centrifuge has been found to be an extremely useful tool for determining capillary pressure curves and for establishing connate water and residual oil in small core plugs. The use of the centrifuge for determining the properties of small core plugs has been discussed in the literature,',' but practically no experimental evidence has been presented justifying the use of this method in preference to other methods (mainly disc method) now in use. Data have been accumulated and are now presented demonstrating the advantages of the centrifugal method, some of which are: (1) rapid establishment of equilibrium, (2) excellent precision yielding very reproducible results, (3) availability of high pressure differences between phases, (4) simple operational procedure, and (5) ability to establish connate water, residual oil, or to obtain complete capillary pressure curve in one day or less. A commercially available centrifuge capable of speeds up to 3,800 rpm, and a high speed attachment providing a maximum rate of rotation of 18,000 rpm were used in this work in conjunction with core holding tubes designed specifically for this application. In view of the outstanding advantages associated with the use of the centrifuge the conclusion has been drawn that this method should be used in place of the more tedious, slower, and less reliable disc method for determining capillary pressure curves and for establishing connate water and residual oil in small core plugs. INTRODUCTION The need for accurate values of connate water, residual oil, and capillary pressure curves in reservoir engineering has been recognized for many years, and the extent of the effort devoted toward solving these problems is reflected in the large number of papers3-" which have appeared in the literature during the past decade. Most of the methods discussed in the recent literature employ a porous disc as a semi-permeable membrane to separate two immiscible phases and make pos-ible the application of an explicit difference in pressure between two phases in the core. Thus, in the determination of the capillary pressure curve the wetting phase (water) is displaced by the non-wetting phase (air or oil). Several investigators1,2 have used centrifugal forces to develop pressure differences between phases. As a result of the first work' in this field the conclusion was reached that "the more rapid centrifugal method for measuring irreducible saturation may have equal value, (compared to use of discs) but more work is required to establish this point." This work was followed in 1945 by a more detailed study2 in which the concepts of this experimental work were more clearly enunciated. A method for calculating saturation for any given speed of rotation based on the observed volume of water displaced was developed and a wider application of the method was suggested. The absence of any subsequent pertinent literature on this subject is interpreted as indicating that no additional work has been completed to substantiate or deny the earlier claims and suggestions of promise contained in the original papers on this subject. One purpose of this report is to provide evidence designed to establish the practical value of centrifugal methods in determining core properties such as connate water and capillary pressure curves. It is also our purpose to suggest a broadening of the scope of this tool to include determinations of residual oil by gas or water drives. THEORY AND PRACTICE IN USE OF CENTRIFUGE Hassler and Brunner2 have clearly presented the basic concepts involved in the use of the centrifuge by relating the performance of a small core in a field of high acceleration to the

Jan 1, 1951

By R. A. Morse, P. M. Bridges, L. E. Wilsey, Howard N. Hall, P. L. Terwilliger

Theoretical and experimental investigations of a constant pressure gravity drainage system are reported. Experimental data are presented to show that recovery to gas breakthrough by gravity drainage is inversely proportional to rate. The gravity drainage reference rate, which is numerically equal to the so-called "maximum theoretical rate of gravity drainage" is shown to have no particular significance from a recovery standpoint. Before this rate can be used as a basis of comparison for recoveries, it is necessary that the relative permeability and capillary pressure characteristics and displacing fluid viscosities be identical for the systems compared. A method is presented by which accurate prediction of the performance of a gravity drainage system can be made. Close agreement between experimental and calculated drainage performance shows that steady state relative permeability and static capillary pressure data can be used to describe fluid displacement behavior. The very wide range of liquid recoveries before gas breakthrough which result from production rate variation alone demonstrates the importance of this factor in planning depletion of a gravity drainage reservoir. Calculated results are presented which show that little additional recovery can be expected from a high pressure gravity drainage system between the times of gas breakthrough and attainment of such high gas/liquid ratios as to make further pressure maintenance impractical. INTRODUCTION It bas been recognized for some time that gravity forces play an important part in the recovery of oil from some types of reservoirs. Field experience has shown that under certain conditions, gravity drainage can result in very high oil recov- eries. Qualitative reasoning has led most engineers to the general conclusions that: (1) Where gravity drainage is important, the reservoir pressure should be maintained by gas injection at the crest of the structure to prevent shrinkage of the oil in place and to keep a low viscosity so the oil can drain at the fastest possible rate. (2) Recovery by gravity drainage is rate sensitive. A survey of the literature indicates that while considerable work has been done on the effects of gravity in oil production problems, no satisfactory method of calculating the performance of gravity drainage reservoirs has been reported.1,2,3,4,5 In the absence of any proven method of calculating reservoir performance, the level at which pressure should be maintained and the rate of production for most efficient operation has been open to debate. The limits and general character of the recovery us rate relationships are apparent from the following: As rates of production approach zero, oil will drain by virtue of its own weight fast enough that the saturation distribution is always approximately the same as the original static capillary distribution. That is, at the gas-oil contact the liquid saturation goes from 100 per cent to a value of perhaps 10 to 30 per cent in a very short distance, so that as production continues. a relatively sharp gas-oil contact moves down-structure, leaving a very low residual oil saturation in the originally oil saturated zone. At very high rates of production, the oil that drains by virtue of its own weight is negligible and recovery will approach that of a horizontal gas drive, leaving a much higher residual oil saturation. At intermediate rates of production. recovery should be between these extreme*. Despite the lack of quantitative methods, tentative agreement had been reached on the question of optimum producing rate. It has been generally concluded that rather sharp decrease in recovery would occur at rates of production above the "maximum rate of gravity drainage" and hence this rate should not be exceeded. The "maximum rate of gravity drainage" is defined as the rate of production from a 100 per cent

Jan 1, 1951

By R. L. Slobod, W. L. Prehn, Adele Chambers

The centrifuge has been found to be an extremely useful tool for determining capillary pressure curves and for establishing connate water and residual oil in small core plugs. The use of the centrifuge for determining the properties of small core plugs has been discussed in the literature,',' but practically no experimental evidence has been presented justifying the use of this method in preference to other methods (mainly disc method) now in use. Data have been accumulated and are now presented demonstrating the advantages of the centrifugal method, some of which are: (1) rapid establishment of equilibrium, (2) excellent precision yielding very reproducible results, (3) availability of high pressure differences between phases, (4) simple operational procedure, and (5) ability to establish connate water, residual oil, or to obtain complete capillary pressure curve in one day or less. A commercially available centrifuge capable of speeds up to 3,800 rpm, and a high speed attachment providing a maximum rate of rotation of 18,000 rpm were used in this work in conjunction with core holding tubes designed specifically for this application. In view of the outstanding advantages associated with the use of the centrifuge the conclusion has been drawn that this method should be used in place of the more tedious, slower, and less reliable disc method for determining capillary pressure curves and for establishing connate water and residual oil in small core plugs. INTRODUCTION The need for accurate values of connate water, residual oil, and capillary pressure curves in reservoir engineering has been recognized for many years, and the extent of the effort devoted toward solving these problems is reflected in the large number of papers3-" which have appeared in the literature during the past decade. Most of the methods discussed in the recent literature employ a porous disc as a semi-permeable membrane to separate two immiscible phases and make pos-ible the application of an explicit difference in pressure between two phases in the core. Thus, in the determination of the capillary pressure curve the wetting phase (water) is displaced by the non-wetting phase (air or oil). Several investigators1,2 have used centrifugal forces to develop pressure differences between phases. As a result of the first work' in this field the conclusion was reached that "the more rapid centrifugal method for measuring irreducible saturation may have equal value, (compared to use of discs) but more work is required to establish this point." This work was followed in 1945 by a more detailed study2 in which the concepts of this experimental work were more clearly enunciated. A method for calculating saturation for any given speed of rotation based on the observed volume of water displaced was developed and a wider application of the method was suggested. The absence of any subsequent pertinent literature on this subject is interpreted as indicating that no additional work has been completed to substantiate or deny the earlier claims and suggestions of promise contained in the original papers on this subject. One purpose of this report is to provide evidence designed to establish the practical value of centrifugal methods in determining core properties such as connate water and capillary pressure curves. It is also our purpose to suggest a broadening of the scope of this tool to include determinations of residual oil by gas or water drives. THEORY AND PRACTICE IN USE OF CENTRIFUGE Hassler and Brunner2 have clearly presented the basic concepts involved in the use of the centrifuge by relating the performance of a small core in a field of high acceleration to the

Jan 1, 1951

By L. E. Wilsey, R. A. Morse, P. L. Terwilliger, Howard N. Hall, P. M. Bridges

Theoretical and experimental investigations of a constant pressure gravity drainage system are reported. Experimental data are presented to show that recovery to gas breakthrough by gravity drainage is inversely proportional to rate. The gravity drainage reference rate, which is numerically equal to the so-called "maximum theoretical rate of gravity drainage" is shown to have no particular significance from a recovery standpoint. Before this rate can be used as a basis of comparison for recoveries, it is necessary that the relative permeability and capillary pressure characteristics and displacing fluid viscosities be identical for the systems compared. A method is presented by which accurate prediction of the performance of a gravity drainage system can be made. Close agreement between experimental and calculated drainage performance shows that steady state relative permeability and static capillary pressure data can be used to describe fluid displacement behavior. The very wide range of liquid recoveries before gas breakthrough which result from production rate variation alone demonstrates the importance of this factor in planning depletion of a gravity drainage reservoir. Calculated results are presented which show that little additional recovery can be expected from a high pressure gravity drainage system between the times of gas breakthrough and attainment of such high gas/liquid ratios as to make further pressure maintenance impractical. INTRODUCTION It bas been recognized for some time that gravity forces play an important part in the recovery of oil from some types of reservoirs. Field experience has shown that under certain conditions, gravity drainage can result in very high oil recov- eries. Qualitative reasoning has led most engineers to the general conclusions that: (1) Where gravity drainage is important, the reservoir pressure should be maintained by gas injection at the crest of the structure to prevent shrinkage of the oil in place and to keep a low viscosity so the oil can drain at the fastest possible rate. (2) Recovery by gravity drainage is rate sensitive. A survey of the literature indicates that while considerable work has been done on the effects of gravity in oil production problems, no satisfactory method of calculating the performance of gravity drainage reservoirs has been reported.1,2,3,4,5 In the absence of any proven method of calculating reservoir performance, the level at which pressure should be maintained and the rate of production for most efficient operation has been open to debate. The limits and general character of the recovery us rate relationships are apparent from the following: As rates of production approach zero, oil will drain by virtue of its own weight fast enough that the saturation distribution is always approximately the same as the original static capillary distribution. That is, at the gas-oil contact the liquid saturation goes from 100 per cent to a value of perhaps 10 to 30 per cent in a very short distance, so that as production continues. a relatively sharp gas-oil contact moves down-structure, leaving a very low residual oil saturation in the originally oil saturated zone. At very high rates of production, the oil that drains by virtue of its own weight is negligible and recovery will approach that of a horizontal gas drive, leaving a much higher residual oil saturation. At intermediate rates of production. recovery should be between these extreme*. Despite the lack of quantitative methods, tentative agreement had been reached on the question of optimum producing rate. It has been generally concluded that rather sharp decrease in recovery would occur at rates of production above the "maximum rate of gravity drainage" and hence this rate should not be exceeded. The "maximum rate of gravity drainage" is defined as the rate of production from a 100 per cent

Jan 1, 1951

By A. F. Meger

REPRESENTED here are the ideas and varied experiences of many people in the Hanna Coal Co. who have helped develop, over a number of years, an efficient and flexible method for spraying con- trolled amounts of oil on coal. Since the George- town preparation plant began operations early in 1951, oil treatment of coal has received special attention. It is believed that oil treating will satisfy present customers and also attract new markets. The first step in developing the new method of oil spraying was the construction of a dust cabinet for testing 50-lb samples of treated coal with the available oil sprays on the market. Tests results were tabulated for both indoor and outdoor storage.

Jan 7, 1954

By K. A. Natarajan, I. Iwasaki

With a platinum electrode the Eh-pH response in aqueous systems follows an empirical relation [Eh = E- 0.059 pH](1) where E usually carries a value between 0.8 and 0.9 v. The same potential (E) is observed with a number of other noble metal electrodes in the absence of surface poisoning and of other well-defined redox couples. Many sulfide mineral electrodes also respond in a similar manner in solutions containing their respective ions over wide pH ranges, especially in the alkaline pH region. Such a parallelism between noble metal and sulfide mineral electrodes points to certain implications of their surface conditions, and the flotation and leaching behaviors of sulfide minerals under aerated conditions may be inferred with respect to the foregoing Eh-pH response. Comparison of Sulfide Mineral and Noble Metal Electrodes [Fig. 1] shows the Eh-pH response of pyrite, galena, chalcocite, and pyrrhotite electrodes, reported by Sato, and some experimental points obtained with a platinum electrode in distilled water. [Eq. 1] is seen to be followed by all these electrodes. It is interesting to note that the response of the pyrite electrode as shown is identical to

Jan 1, 1973

By T. R. Cass

THE renewed interest in titanium, resulting from its increasing application as a structural material, has stimulated basic deformation studies on this metal. In the course of our work, we have developed a dislocation etchant and applied it to a perfection study of melt-grown single crystals as well as to a preliminary investigation of plastic deformation in titanium. The etchant, Keller's etch (21 cu cm HF, 64 cu cm HC1, 106 cu cm HNO3, and 160 cu cm H20), reveals the emergence of both grown-in and fresh dislocations on pure titanium and a-phase Ti-Al single crystals. Pits are produced only on surfaces within a few degrees of the basal plane; the more exactly parallel to a basal plane the surface is, the more distinct are the pits. The observed pit density, however, does not appear to depend on the surface orientation; the pits simul- taneously become less distinct as the misorientation from a basal plane increases. Etch times are short, a few seconds, for pure titanium; longer times are necessary for alloy crystals.

Jan 1, 1968

By Elmer A. Holbrook

You moderns think of your field of work as "Minerals Beneficiation"; to me it always will be "Ore Dressing." While I would like to talk with you on the future of ore dressing rather than the past, I cannot do this because I started to work in the field some 56 years ago, and my future is behind me. It is trite to remind you that then, in 1900, one out of every 30 high school graduates went on to higher education. Today, the figure is one in every three. So that, while you have a lot more men to compete with, the field of opportunity has expanded even more.

Apr 1, 1956

SIR ROBERT HADFIELD, London, England (written discussion*).-We have in the past known so little about tungsten that an important paper such as Mr. Zay Jeffries contributes is most welcome. I have not much personal knowledge on the subject except as regards combinations of iron with tungsten. I put forward the results of my research on natural alloys in 1903,1 and so far as I know the facts there presented still stand. Singular to say, tungsten added to iron affects the electrical resistance less than any other added element. The following tables taken from research work by myself and Sir William Barrett may be of interest.

Jan 10, 1918

By John V. Beall

Beall: Mr. Bennett, you have had a very successful -and a very colorful-career in mining. Would you tell us about your first job in the mining industry? Bennett: I was a mine surveyor on the Mesabi and Marquette ranges, working both open pit and underground. I worked two years for the Meriden Engineering Co., formerly the Meriden Iron Co., which was founded in 1904 to operate mines and to act as a lessors' agent for inspection. At the time I was there, Meriden was operating one open pit and one underground mine, and acting as agent or inspector for some lessors, the owners of the fee interest.

Jan 1, 1968

By A. P. Miller, T. S. Washburn

Improved procedure in the manufacture of rail steel has come as the rail user demanded better wearing qualities combined with greater unit weight. With each weight increase per lineal yard has come greater difficulty in making a product that would successfully withstand all tests that modern rails must meet. With these facts in mind, and with a sincere desire to produce a rail whose service in track would be satisfactory in all respects, the steelmaker was quick to realize that all of the factors entering into his process would have to be more closely controlled. Control of rail-steel slags was recognized as one of the most important of many interdepending factors. The object of slag control is to hold the slag compositions within a range that gives the best results with respect to economy of production, uniformity of analysis, and quality of the finished rails. The most important component of the slag from the standpoint of these production and quality factors is the ferrous oxide content. This component is a good indicator of the basicity and oxidizing power of the slag, and these largely govern the effect of the slag on the steel. Consequently, the

Jan 1, 1935