Search Documents

By O. D. Sherby, J. E. Dorn

SEVERAL years ago Zener and Hollomon1 suggested that the flow stress of metals might be related to the temperature and strain rate in accord with the functional equation: s=s(eeh/rt) [1] at the same state. The Zener-Hollomon relation also contains the significant tacit implication that the energy for activation, AH, is substantially independent of the state of the material. The utility of this method for correlating creep data with tensile data was illustrated in a preliminary reportL on the effect of alloying additions on the secondary creep rates of binary a solid solutions in aluminum as shown for Al-Mg alloys in Fig. 1. Not only do the secondary creep and ultimate tensile properties for each alloy correlate well on this plot but in addition the activation energy, AH = 17,900 R cal per mol. is identical for the various compositions. Similar types of curves correlating the secondary creep rates at 422°K (300°F) with ultimate tensile data were also obtained for a series of dilute a solid solutions of copper, germanium, zinc, and silver in aluminum. In all cases the activation energy for creep, AH, was found to be equal to about 17,900 R cal per mol independent of the type of alloying element or its concentration. The coincidence of the activation energies for these alloys is probably due to the fact that the activation energies for creep are rather insensitive to small composition changes. Alloying additions, as shown in Fig. 1, however, increased the stress necessary to obtain equivalent values of ee?H/RT. Thus the stress level in curves of the type represented by Fig. 1 gives the relative creep strengths of the various alloys. Inasmuch as these correlations between creep and tensile data were obtained for creep tests at 422°K, it appeared advisable to ascertain the range of secondary creep rates and temperatures over which correlations between creep and tensile data could be made on the basis of the Zener-Hollomon relationship. If, for example, the activation energy changes with different ranges of creep temperatures, the utility of the proposed analysis would be severely weakened. But if AH is constant not only for all dilute alloys, but also over wide ranges of temperature and secondary creep rates, confidence will be developed not only in the broad utility of the Zener- Table I. Chemical Analysis':' and Grain Size of Alloys Mean Grain Residual Impurities. Wt Pct Diam- Alloying Atomic-eter, Element Pct Si Fe Cu Mg Mn mm Aluminum 99.987 0.003 0.003 0.006 0.001 0.25 Magnesium 1.617 0.003 0.004 0.006 0.26 Copper 0.101 0.003 0.003 0.0006 0.001 0.29 Zinc 1.616 0.003 0.005 0.007 0.001 '0.26 * The authors express their appreciation to the Aluminum Company of America for the preparation and chemical analyses of these alloys. Hollomon relationship, but also in its theoretical justification. The following investigation was instituted in order to ascertain the range of validity of the Zener-Hollomon relationship when it is applied to creep and tension data. Materials, Equipment, Technique In view of rather extensive correlatable data now available on the plastic properties of a series of binary a solid solutions of magnesium, copper, germanium, zinc, and silver in aluminum, these alloys were again selected for the present investigation. Previous reports have already covered the tensile properties of these alloys at subatmospheric temperatures," and at elevated temperature," as well as their fatigue properties at atmospheric temperatures, nd their creep properties at 422°K.' Resistivity measurementsa as well as precision lattice constant determinations? evealed that these alloys are a solid solutions. After homogenization. 0.100 in. thick sheets were rolled to 0.070 in. in thickness and recrystallized to about the same grain size. Since the details of these treatments were reported previously," they will not be repeated here. In order to appropriately reduce the scope of creep tests in this investigation only the typical alloys shown in Table I were investigated. All creep specimens were machined such that their tensile axes were in the rolling direction of the 0.070 in. sheet stock. The gage section was 2 in. long and 0.500 in. wide with a reduced section of 3.50 in. Creep strains were measured by means of rack and pinion type extensometers with a sensitivity of 0.005 in. per division. Readings were estimated to 1/10 of

Jan 1, 1953

By Grimes, J. A.

EXTENSIVE discovery 'and rapid exploitation of orebodies within the past half century have attracted many able geologists to the mining industry and furnished them a wealth of data from which to develop theories concerning ore genesis. By tosting and elimillating theories which are not sufficiently sup- ported by fact, or which are based on inaccurate observation of field data, the trend of geological opinion has . moved strongly in certain directions until, at the present time, large numbers of geologists subscribe to a broad concept of .ore genesis that I would summarize as below:

Jan 1, 1928

By Wayne Loel

The application of aerial photographs to all phases of geologic mapping is set forth, indicating the advantages to be gained in different types of country and undcr varying climatic conditions. Methods of field and office procedure are given from a geological point of view, as well as suggestions regarding the best methods of aerial mapping for different uses and under varying field conditions, including the study of submarinc geology. Aerial photographs with accompanying geologic maps are shown to illustrate the appearance from the air of different geologic features under varying climatic and topographic conditions. Introduction The following paper is in no sense a contribution to knowledge; it is merely an attempt to indicate some of the benefits that may be expected from the use of aerial photographs in geologic mapping and to mention some inherent limitations. The writer has used aerial photographs in his own work for the past 13 years and has had ample opportunity to observe their use in the hands of others. From this experience certain conclusions have been drawn, which may be helpful to those using aerial photographs for the first time. It must he remembered that a photograph of the earth's surface can delineate only that which the eye can see; therefore the geologist should not expect more from an aerial photograph than he would be able to observe were he in the photographer's airplane looking at the area to be photographed. Theoretically, if the geologist had sufficient artistic ability, he could draw as good a geologic map from his position in the plane as he could from observation of the photograph. Practically this cannot be done because the airplane moves at a high rate of speed, which in itself prohibits detailed observation and, no matter how great the geologist's artistic ability, he could not reproduce the detail that can be recorded by a camera. An aerial photograph is a picture map of an area. The picture may be studied in the office until the geologist is thoroughly familiar with every minute detail of the surface of the ground he is about to geologize. If it is an area, underlain by sedimentary rocks, much may be learned

Jan 1, 1941

By Wayne Loel

The application of aerial photographs to all phases of geologic mapping is set forth, indicating the advantages to be gained in different types of country and undcr varying climatic conditions. Methods of field and office procedure are given from a geological point of view, as well as suggestions regarding the best methods of aerial mapping for different uses and under varying field conditions, including the study of submarinc geology. Aerial photographs with accompanying geologic maps are shown to illustrate the appearance from the air of different geologic features under varying climatic and topographic conditions. Introduction The following paper is in no sense a contribution to knowledge; it is merely an attempt to indicate some of the benefits that may be expected from the use of aerial photographs in geologic mapping and to mention some inherent limitations. The writer has used aerial photographs in his own work for the past 13 years and has had ample opportunity to observe their use in the hands of others. From this experience certain conclusions have been drawn, which may be helpful to those using aerial photographs for the first time. It must he remembered that a photograph of the earth's surface can delineate only that which the eye can see; therefore the geologist should not expect more from an aerial photograph than he would be able to observe were he in the photographer's airplane looking at the area to be photographed. Theoretically, if the geologist had sufficient artistic ability, he could draw as good a geologic map from his position in the plane as he could from observation of the photograph. Practically this cannot be done because the airplane moves at a high rate of speed, which in itself prohibits detailed observation and, no matter how great the geologist's artistic ability, he could not reproduce the detail that can be recorded by a camera. An aerial photograph is a picture map of an area. The picture may be studied in the office until the geologist is thoroughly familiar with every minute detail of the surface of the ground he is about to geologize. If it is an area, underlain by sedimentary rocks, much may be learned

Jan 1, 1941

By C. EDWARD STAFFORD

A Discussion of the paper by Mr. James P. Roe which was read at the Washington meeting, May, 1905. MR. C. EDWARD STAFFORD, Chester, Pa.:-During all my business life, I have been engaged in the manufacture of Bessemer and open-hearth steels, but, during my long connection with the Shoenberger Steel Co. of Pittsburg, I had some experience in the manufacture of high-grade puddled iron for horse-shoes and in the making by Dr. Otto Wuth's process extremely pure low phosphorus puddled blooms (analyzing from 0.005 to 0.01 per cent. of phosphorus and sulphur), which were melted with low-phosphorus pig-iron in acid open-hearth furnaces to make extra locomotive fire-box steel. I have also seen the Dank's puddlers in operation at different times and places, notably where they were most successful, at the Otis Steel Works, Cleveland, Ohio; then under the management of our friend, Mr. S. T. Wellman. These Dank's blooms were made solely for open-hearth melting-stock to which they were well adapted ; the unavoidable presence of bits of ore-fix imbedded in the mass of the, metal always prevents the profitable manufacture of merchant iron from Dank's blooms. With the experience just described, I was to some degree in position to value fairly the means, methods and results of Mr. Roe's mechanical puddling from the metallurgical or technical and economic points of view, when given an opportunity by Mr. Roe to see his puddling furnace or machine in operation in Pottstown, Pa. Briefly, the furnace, with water-cooled bottom, is rectangular in plan, about 20 by 8 ft. in the clear, suspended by trunnions at the middle of the long sides, at a. height of 17 or 18 ft. above the general level; the oscillation (65° each way from the vertical) is accomplished by geared segments (attached to the downward-projecting side or trunnion-plates) with which engage pinions driven by a reversing engine. The whole section

Sep 1, 1905

By James S. Baker

LARGER than continental United States but with only about one third the population, Brazil is a land of enormous potential wealth, waiting to be developed. During a recent visit to that country I saw Brazil at war and learned about some of the recent mineral developments. Many engineers and geologists have been sent to Brazil by various U. S. Government agencies to assist the Brazilian producers and co-operate with the Brazilian Government in producing needed war minerals. The Foreign Economic Administration staff of engineers has been active and through their assistance to the Brazilian producers, steadily increasing quantities of strategic minerals were provided to aid the United Nations' war effort. Mineral wealth has been found in almost every state of Brazil. Many mineral deposits have been discovered during the war period. Examples are: barite near Bahia; the tungsten and molybdenum deposits in Rio Grande do Norte; and corundum, beryl, and tungsten ores in Ceara.

Jan 1, 1945

By C. C. Whittier

CIVILIZATION'S PROGRESS, which has multiplied man's comforts, conveniences, a n d happiness, is based upon the extensive employment of natural minerals and sources of energy. Mineral resources are basic factors in modern economic development, machine industry, international trade and world power. A survey of mineral consumption shows that the United States leads the world in the production and consumption of energy materials, of metals, and of the large and diverse array of earth materials that fall in the nonmetallic mineral group. The use of nonrnetallic minerals exceeded both the metals and the fuels in the long period before the industrial age, but it is only in the last two decades that consumption of non- metals has kept pace with and approximated in value the output of metals. Although the data of production in the first half of the last century are meager and fragmentary, the record of the past fifty years-the period of most rapid growth-is available, and reveals an astounding growth.

Jan 1, 1933

Abbey. Robert Graham, District Mgr.. The W. W. Sly Mfg. Co., 50 Church St., New York, N. Y. '21 Abbott, Clarence E., V.P., Charge of Raw Materials, Tenn. Coal, Iron & R. R. Co., 1242 Brown-Marx Bldg., Birmingham, Ala. '04 Abbott, Louis Benjamin, Chief Engr., Consolidation Coal Co., Watson Bldg., Fairmont, W. Va. '15 Abeel, George H., Jr., Cons. Min. Engr 12S1, S. Canon Dr., Beverly Hills, Cal. '18 4 -Abel, Raymond L., Asst. Prof., Dept. of Pet. Refin.. Univ. of Pittsburgh. Pittsburgh, Pa. '28 Abel, Walter D., Cons. Engr 650 S. Grand Ave., Los Angeles, Cal. '82 Abele. Louis T., Min, & Met. Engr., Supt., Texas Hill Mine Coulterville, Cal. '31 Abell, Leo M Sullivan Concentrator, Chapman Camp, B. C., Canada '31 Abernathy, George Elmer, Prof. of Geol. & Min., Kansas State Teachers College. Pittsburg, Kan. '20 Aborn, Robert H., Asst. Met., Research Lab., U. S. Steel Corp., Lincoln Highway, Kearny, N. J. '19 Abraham, W. E. V., Member, Geological Staff of Burmah Oil Co., Ltd., Nyaunghla, Upper Burma, India. '28 Abstein, Henry T., Engr. & Mgr., Profile-Tamarack Mines Co Yellow Pine, Idaho '27 Acker, E. O'C., Met 128 East Washington Lane, Germantown, Philadelphia, Pa. '86 Ackerman, D. E., Met., Research Lab., International Nickel Co., Inc Bayonne, N: J. '24 Ackerman, George F., Engr., Real del Monte y Pachuca Min. Co., Apt. 3, Pachuca, Hgo., Mexico '29 *Acres. T. H.. Geol. Dept., Valuation & Pet. Engrg., Richfield Oil Co., 555 S. Flower St., Los Angeles, Cal. '29 Adachi, Jinzoo Address Wanted '88

Jan 1, 1934

By J. B. Conway

RECENT studies of first-stage creep data have led to a special least-squares procedure for use in calculating the Andrade creep-equation constants. This procedure is easy to apply, uses only experimental data, and yields results which do not vary with the individual making the analysis. Taking logarithms of the Andrade equation I = lo(1 +ßl1/3)ekt leads to In l = In lo + In(1 + ßl1/3) + kt A residual can then be defined as the difference between the logarithm of an experimental length value and the logarithm of a calculated length value. Following the usual least-squares approach differentiation with respect to 10 and k of the expression for the sum of the squares of the residuals leads to two equations which cannot be solved directly for the three constants involved. However, values of ß can be assumed and corresponding values of lo and k can then be calculated. Then the sum of the squares of the residuals can be calculated. For a certain value of ß this sum will exhibit a minimum value to identify the least-squares values for ß, lo, and k. An illustration of the application of the above least-squares approach is obtained by employing the creep data for lead originally presented by Andrade' in the development of the one-third creep law. A plot of the sum of the squares of the residuals as a function of ß is shown in Fig. 1 along with the corresponding lo and k values. The minimum is seen to occur at ß = 0.0143 from which lo = 39.149 and k = 7.27 x 10-5. Based on these results the Andrade equation for these lead data is 1 = 39.149(1 + 0.0143 t1/3)e7.27 x 10-5t compared to the equation I = 39.13(1 + 0.01457/l/3)e6.95 X 10-5t developed by Andrade (calculation procedure not given but was probably a graphical solution). Calculating length values using the above equations and comparing with the experimental length values, residuals corresponding to the difference between experimental and calculated length values can be obtained. The sum of the squares of the residuals can then be calculated. For the case of the least-squares approach a value for this sum was found to be 2.37 x 10-3 compared to a value of 3.47 x 10" for the equation originally proposed by Andrade. In other words, while the constants proposed by Andrade provide an excellent fit for the lead data, a still better representation is afforded by applying the least-squares approach discussed above. A similar result was obtained for the lead data at 162oc.l The least-squares approach led to 1 = 9.866(1 + 0.0497 t1/3)el.011 x 10-2t compared to the equation I = 9.94(1 + 0.0433 l1/3)e1.06 X 10-2t given by Andrade. In this case, too, the sum of the squares of the residuals is slightly smaller for the equation based on the least-squares approach. It should be pointed out that a double trial and er-

Jan 1, 1965

By W. C. Ellis, M. E. Fine

WHEN certain binary Fe-Ni alloys are worked cold and then stabilized by a stress-relief anneal, their Young's moduli are nearly invariant over a substantial temperature range determined by composition and work-anneal history.' In the present investigation addition of molybdenum to such alloys (besides increasing the yield strength) was found to diminish the sensitivity of the thermal coefficient of Young's modulus to composition changes. Such alloys are of interest for applications requiring 1 a metal with controlled, low temperature coefficient of Young's modulus and substantial magnetic permeability.' Young's modulus ordinarily decreases with rising temperature. In ferromagnetic alloys a change in modulus on heating due to loss of ferromagnetism modifies the .temperature dependence. Far below the Curie temperature ferromagnetism alters the modulus in two ways: a—Addition of the energy of magnetization, a function of interatomic distance, changes the relation between interatomic energy and distance.' This lowers the modulus in the Fe-Ni and Fe-Ni-Mo alloys of this investigation. b—An applied stress changes the ferromagnetic domain arrangement so that linear magnetostriction contributes to the strain and further lowers the modulUs.~ Since in the alloys of this investigation both effects lower the modulus, loss of ferromagnetism on heating changes the slope of the modulus-temperature curve in a positive direction. With increasing temperature the slope of the modulus-temperature curve, due to progressive loss of ferromagnetism, becomes less negative, goes through zero (the modulus is minimum), becomes positive, and resumes its normal negative value above the Curie temperature.' The increase in modulus and decrease in curvature in the modulus-temperature curve occurring on work hardening have been attributed to a reduction in effect (b).'. Vn the absence of ferromagnetism work hardening through introduction of residual strains would be expected to decrease the modulus.' Alloy Preparation—Test Methods Four series of alloys having nominal molybdenum contents of 5, 7, 9, and 10 pct and containing 47 to 58 pct Fe (the analyzed compositions are given in Table I) were melted in air and cast as bars weighing from 2 to 6 lb. The charge consisted of electrolytic nickel, Armco iron, molybdenum (99+ pct) or ferromolybdenum (62 pct Mo), manganese, and aluminum as a deoxidizer. The bars were swaged cold to the desired diameters with intermediate anneals. Alloys in this composition range are reported" to be face-centered cubic and ferromagnetic at room temperature. The Curie temperatures" decrease with molybdenum. For example, keeping the Ni/Fe ratio at unity and increasing the molybdenum from 0 to 17 pct decreases the Curie tempera- ture from approximately 500°C to room temperature. (The 17 pct Mo alloy requires quenching to retain a single phase.~) Young's modulus at a series of temperatures from —50" to 100°C was determined by a dynamic method previously described.', " In this method Young's modulus is calculated from the resonant frequency (in this case approximately 50,000 cycles per second) of a rod sample (approximately 2 in. long) vibrating longitudinally in the first mode. The densities of the samples at room temperature, Table I, were determined by the standard method of weighing in air and reweighing in redistilled bromobenzene. The linear coefficients of expansion, Table I, needed to calculate the sample length and density at the temperature of measurement, were obtained by observing the change in length (22" to 100°C) of an 8 in. gage distance with a two microscope cathetometer. The values of density and coefficient of expansion in the few samples checked are independent of treatment to the accuracy reported. This was assumed to be general for all the samples. The modulus values are accurate to &0.05x101' dynes per sq cm. However, values of thermal change in modulus are accurate to 20.005~ 10" dynes per sq cm. Young's Modulus Values at 25°C: The modulus values of O', 5, and 10 pct Mo alloys at 25 °C are plotted in Fig. 1 as functions of nickel. After working cold, the samples were either recrystallized at 950" to 1000°C or given a low temperature stabilizing anneal at 400° C. The 400°C anneal does not reduce the hardness nor cause recrystallization. Annealing at 400 °C does

Jan 1, 1952

By C. A. Hansen

The furnace used for experimental work is shown in Fig. 1. One fireclay sagger, or pot, was set within another and the space between the two filled with Silox heat insulation. The hearth is a cast-iron plate with an imbedded ribbon of nichrome wire; this wire heater is connected to a potential regulator, which permits a very close voltage control. A mechanically driven arm is fitted with rabble blades so arranged that a uniformly thick ore bed may be maintained indefinitely. This arm is usually driven at about one revolution per minute but its speed of rotation can be varied as desired. Compressed air is led into the furnace through a meter, and it was found necessary to preheat the air in order to secure the definitely isothermal conditions sought. With this arrangement, it is possible to maintain any desired temperature constant within about 5" C. for any desired length of time and to

Jan 1, 1921

By S. C. Dhara

A process of solvent extraction and separation of platinum group metals (PGM) and gold using primary, secondary, tertiary, and quarternary organic amines has been briefly described. The effects of amine structures; the use of diluents; the principle of synergism and antisynergism in the mixed extractants; the oxidation states of metal ions are explained in the amine extraction process of precious metals.

Jan 1, 1984

By E. Sengier

At the Director's dinner of the A.I.M.E. on. April 22, Mr. Sengier of the Union Minière du Haut Katanga was a guest. Though a member of the Institute for sev-eral years this was the first occasion on which he had had opportunity to meet with it, and in response to an invitation from President DeGolyer, after expressing his pleasure at being present, he told informally of the present development of the Congo with which he has been so closely related. From his remarks the follow-ing has been prepared.-EDITOR. AS you know, the Belgian Congo, a fairly large colony compared with the territory of Belgium, is in the center of Africa. Natural waterways, railroads now built and new railroads under construc-tion, give increasing means of transportation and are helping toward development. The mining industry is by far the most important part of our colonial activity. Considering that we are all engineers, I will confine my figures to mining enterprise. First I will show you the relative importance of the mining industry com-pared with the total exports of the Belgian Congo. During 1925 there was exported 100,000 tons of cop-per, valued at about $25,000,000; 900,000 carats of diamonds, 8000 lb. of gold, 1700 tons of cassiterite, 300 .tons of cobalt, and 20 grams of radium, of a total value of about $35,000,000. Other products to a value of about $12,000,000 and consisting mainly of palm nuts, palm oil, cotton, ivory, copal, rubber, were also exported. From this you will see that mineral products account for about 72 per cent of the total exported value. Copper alone amounts to 52 per cent of the total and 72 per cent of the mineral exports. All minerals, with the exception of gold, which is mined by the government, belong practically toy two mining companies in which American and British capi-tal is interested with Belgian. These two companies (one called Forminière, interested in the diamond busi-ness, and the other called the Union Minière, interested in copper, cobalt, tin and radium) were formed twenty-five years ago. They started producing in 1911, but the war prevented normal operations, and active de-velopment could only be carried on after the Armistice.

Jan 5, 1927

By Paul M. Tyler

THE farmer pays the phosphate miner! Phosphorus is used in fireworks; goes to battle in military smoke screens, incendiary shells, and tracer bullets; and, in vermin destroying pastes, does its part in the war against insects. A lemon phosphate can be had for a nickel at most soda fountains, and tens of thousands of tons of phosphate rock are mined annually for use in the food industries, chiefly for making monocaleium phosphate baking powder. Sodium phosphate cleaning, washing, and scouring compounds consume substantial quantities: the iron and steel industries buy a few thousand tons yearly to make ferrophosphorus and to balance foundry-iron furnace charges; and even nonferrous metallurgists use a little for phosphor bronze and other alloys. Phosphoric acid, its salts, and diverse other derivatives of this versatile element have countless applications, and industrial outlets are increasing rapidly, especially in the United States. Nevertheless, in this country nearly 90 per cent and in the whole world fully 95 per cent of the phosphate rock consumed is absorbed ultimately in agriculture.

Jan 1, 1938

TO THE. BOARD OF DIRECTORS AND MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN Submitted herewith are the report of the Treasurer for the year 1945 and reports for the same year of the following committees: Membership, Admissions, Papers and Publications, Mining and Metallury (Magazine), and Library. In this review of the year by the Secretary reference frequently will be made to the "Paul" Committee and to the "hotter" Committee. The first is the special committee on Divisional Relationships and the second the special Committee on Ways and Means. These two important committees, appointed by President Harvey S. Mudd under authorization of the Board of Directors on March 21, 1945, were composed as follows:

Jan 1, 1946

By M. A. Grossmann

THE hardenability of most steels can be predicted within 10 to 15 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as-quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a ''pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain sue may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter"; namely, the diameter of bar, in inches, that will just harden all the way through (absence of un- hardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test. The data bring out certain features rather clearly. For example: I. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals," are known; thus an "incidental" chromium content of 0.20 per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybde- num when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful as wouldappear to be common experience; observe that an increase from no manganese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.20 per cent Mo provides a factor of 1.63, an increase of over 60 per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added " 20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the first small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater hardenability will be obtained by using, for example, 0.5 per cent of each than by using 1.0 per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost lo per cent in hardenability (in these units); this, however, does not apply to certain steels of high hardenability. It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome- molybdenum and chrome-vanadium steels, undissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum possible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the absence of Cr, and V up to 0.04 per cent), the charts provide reasonable approximations. The precise figures on the charts are suggested as tentative, subject to some modification as more data accumulate, but the fundamental concept appears to be supported by tests made on a wide variety of steels, a few of the correlations being shown in Fig. I.

Jan 1, 1942

By John T., Ryan

THE subject assigned me, "Safety in Mining," is a very broad one and only the high spots can be covered in this short paper. As this is a meeting of the Coal Division, these remarks will be directed largely to coal mine safety, although the principles of safety and effective accident prevention methods are relatively the same in every branch of mining or industrial work. The coal mining industry should take pride in the part it has played in the development of the accident prevention movement, and there is ample proof for the statement that the first real organized accident prevention, work, both abroad and in this country, was con- ducted in the coal mining industry.

Jan 1, 1930

By A. G. Gilbert

Paradoxical is the word. The coal industry, despite reach- ing a 22-year high in production (590 million tons), has been tagged as having its back to the wall vis-a-vis its valiant attempts to quench the nation's still unabated craving for coal. What must be even more reassuring to the industry, infected once with rumors of a uranium takeover, is a nation's almost insatiable appetite for electricity. Between 1967 and the summer of 1970, utility stockpiles were being gobbled up, diminishing to 79% of the January 1968 level.

Jan 1, 1971

By Paul M. Tyler, Carle R. Hayward

DOES it pay to do really good work? Quite likely the practical millman will answer that it does not. The preparation of ores for market is primarily a business enterprise, and by and large the individual operator does not bother his head about squandering our national resources or making easier the job of the smelterman. Having accepted such ore as he may get fro111 the mine, his job is to make the best possible showing with his mill fro111 the standpoint of financial return. His success is measured in dollars and cents, and he has no rightful reason to expect more than scant acknowledgment of any other achievements from the stock- holders of his company who in the last analysis are his employers.

Jan 1, 1936

By John L. Lamont, Walter Crafts

SECONDARY hardening in tempering has long been recognized as a typical characteristic of steels containing large amounts of carbide-forming alloys. These steels, when quenched and tempered, tend to soften somewhat after tempering at low temperatures, and to reharden at intermediate tempering temperatures before finally softening to low hardness. This behavior in tempering has been studied by many investigators, chiefly with respect to the secondary hardening of high-speed steels. The initial softening has usually been ascribed to decomposition of martensite and growth of iron carbide particles. The secondary hardening has been explained by formation of fresh martensite from residual austenite, formation of very fine alloy carbide particles and by precipitation hardening of metallic compounds in the ferritic matrix. However, factors derived for the calculation of tempered hardness in low-alloy steels1 indicated only a tendency toward retarded softening rather than a discontinuous rehardening. A study was, therefore, made to determine whether fresh martensite from residual austenite and precipitation hardening are essential to rehardening and the degree to which tempered martensite could be rehardened by precipitation of alloy carbides. The mechanism of carbide rehardening was also investigated to determine the nature of the process. The causes of secondary hardening in high-speed steel have received serious consideration for about thirty years. Among the earlier workers Bain and Jeffries2 in 1923 recognized residual austenite as a significant factor, but in addition, emphasized the effect of the formation of alloy carbide particles of "critical" size. They conceived that freshly quenched martensite forms low-alloy iron carbide at low tempering temperatures; with further tempering the iron carbide is then modified by alloying elements that can diffuse most readily at intermediate temperatures (850°F); and that the iron carbides grow in size by coalescence so that the steel tends to lose hardness. At higher tempering temperatures carbide stability rather than alloy availability becomes the controlling influence and in high-speed steel "iron-tungsten carbide is the most stable one and forms to the elimination of the earlier formed carbides. . . . The iron-tungsten carbide particles reach approximately the size for critical dispersion after a short reheat at 1100°F." This concept, the formation of alloy carbide nuclei, redissolving of the iron carbide, and diffusion of carbon to the alloy carbide, was restated for vanadium steel in 1932 by Houdremont, Bennek, and Schrader.3 Subsequent studies have confirmed that iron carbide changes to alloy carbide at 1000 to 1100°F, but the mechanism of the process has received little consideration .

Jan 1, 1948