Search Documents

By Andrelio Marcos Ribeiro, Lucio Ribeiro Camisao, Antonio Carlos Ataíde, Alan de Sousa Pereira, Renato Siqueira Campos

The annealing and pickling line n. 1, responsible for the production of stainless steel 3xx, 4xx and 430a in thicknesses from 4 to 0.4 mm, has two vertical strip accumulators. These are intended not to let the material exceed the determined time in the furnace and in the pickling, and consequently do not cause defects like burning and excessive pickling. Strip accumulator n. 1 avoids the line from stopping during welding execution of the coils in the welding machine. In sequence, the strip accumulator n. 2 avoids the line from stopping at the end cutting of the tips, and in the coils removal from the pickling. The strip accumulators have a roller table that during the strip accumulation moves vertically downwards while its counterweight moves vertically upwards, and do the inverse movement when the material is released. On December 12th 2018, the failure occurred in the strip accumulator n. 1, where it was verified that the shaft of one of the pulleys had been fractured by high-cycle mechanical fatigue, which was characterized by alternating bending. With the fracture of the shaft, occurred the unevenness of the counterweight that damaged the guides. Failure analysis of this occurrence was based on the PDCA methodology, when was verified a weld between the shaft and the pulley. The analysis of the microstructure transformation in the molten zone, in the heat affected zone and in the base metal was carried out in an optical microscope, and no abnormality was observed. It was also carried out the end test by penetrating liquid, finding an inadequate weld in its geometry, as well as longitudinal trunks along the center of the weld bead. However, after a huge investigation of the causes, it was found that the failure was triggered by an inadequate design of the pulley shaft. It was also verified that the shaft had an open measure, inadequate for the operational context. After the analysis, action plans were drawn up based on the FMEA methodology to inhibit the failure recurrence.

Oct 7, 2019

By Frenk van den Berg

In the manufacturing of steel strip for the automotive sector, the mechanical properties are largely defined by the process conditions in the hot strip mill. In particular the phase transformation, from austenite to ferrite, which takes place during the forced cooling stages on the run out table (ROT) after the finishing mill, governs the microstructure and hence the mechanical properties.In current practice, metallurgical models are used to predict the phase state at each position in the strip. These model predictions are supported by pyrometer measurements along the ROT. Although reliable in the majority of the situations, both measurements and models sometimes have difficulties in providing robust output. In this paper, we present a new type of inline measurement, which directly measures the amount of phase transformed. The instrument is based on a technique known as impedance spectroscopy. As result of a collaboration of different institutes and companies, the equipment is robustly running during several years exclusively in the Hot Strip Mill of Tata Steel in IJmuiden.

Aug 16, 2017

By Lara de Assis Moreira, Vinicius Thiago Lecco Rampinelli

The energy efficiency of reheating furnaces is a continuous challenge, as these equipment consume a representative portion of the total fuel of an integrated steel plant. Therefore, any investigation and implementation which brings improvement in this figure become an important issue for the mill competitiveness. In the case of production delays due to external factors (the condition addressed in this work), whether predicted or unforeseen, the slabs remain inside the furnace with high temperatures in order to avoid production delay during the production restart, elevating the specific consumption and scale formation. This work increased the energy efficiency of the two ArcelorMittal Tubarão’s walking beam reheating furnaces, by reducing the consumption of mixed gas during production delays (either scheduled or not) lasting less than 3 hours. The objectives were achieved through improvements, among them, tuning of Level 2 automation system parameters, automatization of procedures and operational training. The work resulted in a 34.4% fuel gas consumption reduction during the delays.

Oct 1, 2019

By Pietro Palma

Universal cardan joints are widely used in drivetrains of rolling mills for steel and aluminum making, as well as for non ferrous alloy industry. Working conditions are extremely tough due to high alternating or pulsating rolling torques in the roughing stands and high torques and speeds in the finishing stands. Overloads and lubrication along with oxide and slag are also critical issues that contribute to create severe working conditions. For a constant and reliable power transmission rolling mills performance and uptime rely on Universal cardan Joints which are the most critical equipment of the drivetrain. Fatigue assessment of the most important components of the Universal cardan Joint is therefore definitely vital for the mill in order to avoid failures and consequently downtimes. Considering the component’s dimensions and weight and in addition the time needed in order to reproduce full scale tests, a new approach to study the Universal cardan joint’s main components fatigue behavior has been investigated. It consists in reproducing the local stress condition of the main joint components on small scale specimens that can be tested by conventional laboratory fatigue machines. The aim of this study is to analyze the most critical stress concentration areas in the universal cardan joints highlighting how a universal cardan joint Wöhler curve can be determined through laboratory tests of small scale specimens.

Aug 16, 2017

By Anna Carolina Cerqueira Neves

Synthetic fiber has been gradually replaced by natural fiber, such as lignocellulosic fiber. In comparison with synthetic fiber, natural fiber has shown economic and environmental advantages. The natural fiber presents interfacial characteristics with polymeric matrices that favor a high impact energy absorption by the composite structure. However, until now little has been evaluated about the hemp fiber incorporated in polymeric matrices. This study has the purpose of evaluate the impact resistance of this kind of epoxy matrix composite reinforced with different percentages of hemp fibers. The impact resistance has substantially increased the relative amount of hemp fiber incorporated as reinforcement in the composite. This performance was associated with the difficulty of rupture imposed by the fibers resulting from the interaction of hemp fiber / epoxy matrix that helps absorb the impact energy.

Aug 16, 2017

By Günther Staudinger

Aperam is a global player in producing of stainless, electrical and special steel qualities. The steelmaking plant in Timoteo Brasil is equipped with one AODconverter for stainless steel and one MRPL-converter for special steel production. The MRP-L converter is almost in operation for 20 years. In order to improve production Aperam decided to install a new converter with increased reaction volume equipped with DANIELI state of art technology. This paper describes the major changes and improvements of the new converter installation.

Aug 16, 2017

By Frank Schrama

The Steel Plant Model (SPM) is an advanced logistic simulation model for steel plants. With the SPM, bottlenecks can be solved and logistics can be optimized. Both existing plants and greenfield designs can be simulated. All movements and actions simulated, from hot metal to cast products. Not only all major equipment and their relevant components (like a sublance) are simulated, but also ladles, scrap boxes, transfer cars and cranes. The whole plant is simulated in 3D and actual distances and speeds determine transport times. The SPM includes process time deviations and equipment downtimes for maintenance or unexpected breakdowns. This ensures more realistic and reliable results. Logistic optimization is based on comparison of different scenarios. For a new scenario, equipment and practices, etc. can easily be modified, added or removed. At the same time the SPM produces all relevant data for every new scenario, which can be presented conveniently. This makes the SPM the ultimate tool to find bottlenecks or optimize plant logistics. The SPM is validated for several plants world-wide, with different characteristics and layouts. The SPM not only realistically simulates existing plants with all utilizations, crane movements and waiting times, but also to accurately predicts the influence of plant modifications or unexpected events like breakdowns. Given the flexibility of the SPM, any (new) steel plant can be simulated quickly when a layout and the requested data are provided.

Aug 16, 2017

By Fabiano Almir Barbosa, Eduardo Alves Machado, Felipe Ferreira Cajano, Bruno Rodrigues Henriques

Spring steels are usually classified as medium to high carbon low alloy steels with very high yield strength, enabling the part to return to its original shape regardless of significant bending or twisting. Despite the fact that plain carbon steels are suitable for small springs, larger and high performance springs usually requires alloy steels such as Cr-V or Si-Mn in order to achieve an even microstructure throughout the cross section. Clutch diaphragm spring is a high performance part that requires very good cleanliness and microstructure homogeneity, thus requiring an alloy steel. In this paper was studied, in an industrial scale, the process parameters and critical characteristics for the development of a Cr and V alloyed high carbon sheet steel for the production of clutch diaphragm spring. The steel was characterized throughout the entire process (casting, hot rolling, cold rolling + batch annealing and heat treated) using tensile test, hardness test, optical microscopy (OM) and scanning electron microscopy (SEM) to assess the mechanical and metallurgical properties of the studied steel. The results have shown the material’s microstructure evolution after each main stage of the process, from a ferrite-bainite/perlite based microstructure as hot band to fully spheroidized as cold-rolled/annealed and then fully martensitic as ready-to-use part.

Oct 1, 2019

By Daniel Mapa Clemente

Processing of tin slags in reduction furnaces was studied in order to optimize tin recovery and reduce recirculation rates of slags containing thorium and uranium oxides. A theoretical approach considering a mass balance of the process was developed and adjusted by experimental results in order to predict the final slag composition. A metallic phase (FeSnSi) was discovered trapped in the slag due to high apparent viscosity, raising the FeO and SnO2 contents of the slag sample. This FeSnSi alloy is rich in tin and its recovery would help to reduce the slags recirculation. High contents of ZrO2 were found in the slag, restricting it from reaching complete fluid phase. Through an analysis of the slag in the CaO-FeOx-SiO2 and ZrO2-CaO-SiO2 phase systems it can be concluded that final slags should be modeled aiming fluid phase at working conditions and additions should be planned in order to control ZrO2 levels.

Oct 30, 2017

By Patrick Edward Connell

The next generation of the well-established 3-roll Reducing & Sizing Block (RSB), the RSB SCS® is the latest milestone in reducing and sizing technology for SBQ products. It offers enhanced bar quality, improved productivity, mill availability and economy as well as a simplified, safe and environmentally friendly operation. A newly developed modular drive concept of the RSB SCS® grants a smaller footprint in the layout, a reduced oil-lubrication volume and a simplified maintenance schedule. Intelligent engineering leads furthermore to reduced hydraulic functions of the RSB SCS®, which ensures a safe and environmentally friendly rolling. Another integral part of the RSB SCS® is an innovative stand changing concept, which allows automatic stand changing within three minutes. The new RSB SCS® also includes a Fast Remote Control (FRC) which enables the immediate adjustment of the roll gap against the rolling force (under load) within milliseconds. Size changes along the free-size range can also be made within the traditional billet gaps in less than five seconds. At the core of the future-oriented RSB SCS® is a real-time closed-loop control system called Size Control System (SCS®) acting with 3-roll stands adjustable under load (AUL) and / or the heavy duty stands. These features remarkably further improve the rolled tolerances and their reproducibility, and at the same time simplify the operation by means of an automated optimization of the process parameters for the rolled bars.

Aug 16, 2017

By Débora Cardoso de Oliveira Silveira, Jean-Christophe Huber, Hamzeh Hamadeh, Kateryna Pastel, Guillaume Brosse

The dynamic behavior of oxygen gas flow, determined by the lance nozzle and blow pattern, is a key factor for determining jet efficiency in BOF Steelmaking. The present work compares the performances of Laval and parabolic nozzles with the aid of the Computational Fluid Dynamics (CFD). The Method of Characteristics (MOC) was applied to design a minimum length parabolic nozzle. The results show that the parabolic nozzle generates more uniform and stable jet, with 2% longer potential core and supersonic length and less shock waves. For the parabolic nozzle, the pressure nearby the nozzle wall is higher, which can protect this region from reverse flow of converter gases and offer longer life for the lance tip. Likewise, the flow rate variations would affect less this nozzle. In addition, the nozzle wear was investigated, and the parabolic nozzle has proven relatively less sensitivity to the presence of this deformity.

Oct 1, 2019

By Stefan Stein, Jorge Davo, Adrian Villanueva, Abhay Kulkarni, Shane Hoff

Pellet sizing plays a key role in the productivity of the entire pelletization and subsequent induration processes, whereas uneven pellet sizing can increase the circulating load of the balling circuit inducing operational instability leading to production loses. The present work focuses in comparing the agglomeration kinetics, expressed as the number of pellets produced in a determined target size range, of different organic binder-bentonite binder systems. The batch experimental results show that the binder system has a great influence in the resulting pellet sizing, which could lead to advantages in terms of balling circuit efficiency and eventually operational de-bottlenecking.

Oct 1, 2019

By Rene Grabowski

Optimization of workflows and intelligent stock management; Slab stacking improvement by automated transport orders; and System automatically registers any slab movements even in manual operation. Case story: Steel producer ArcelorMittal Eisenhüttenstadt GmbH in Germany uses Primetals Technologie’s new stock yard logistics system in its finishing department. An exact image of its slab storage at any times is given by the warehouse logistics system to the company. It not only enhances the composition of the stacks of slabs, but also automates recording of manual restacking operations. Therefore the solution improves workflows and simplifies stock control. Cycle times have also been reduced due to the fact that the slabs can be charged to reheating furnaces ahead of the rolling mill due to less restacking operations within the slab storage. The expandable, modular system is based on the Siemens Simatic IT and Primetals Technologies’ IT4METALS Logistics product platform. It provides a large number of organizational and commercial features in the form of sophisticated graphics and tabular evaluations. For example, it can show how many crane movements have been made per shift for any category of slab, so that the time and cost for each operation can be calculated accurately.

Aug 16, 2017

By Aitor Elorriaga Fernandez de Arroyabe

The purpose of Sinter plants is to heat iron ore fines along with fluxes and coke fines or coal, to produce a semi-molten mass that solidifies into porous pieces of sinter with the needed size and strength. Fluxes used in the sintering process need to have an appropriate size distribution and TI to avoid generation of fines, which could reduce the productivity of the Sinter. Besides, a homogeneous chemical composition and high absorption characteristics are necessary to control the basicity and to combine the flux with P, S, Si, etc, respectively. PASEK Dunite is an ultramaphic rock exploited in the north of Spain with a basic chemical classification, being olivine and serpentine its principal minerals. It is a very homogeneous and hard stone and its main characteristics are: high hot and cold resistance to mechanical stresses, softening and melting points of a flux not of a refractory material. In addition, due to its mechanical and chemical properties, less fines are generated in the sintering process and during the handling and transportation to the blast furnace, improving the productivity of these processes. In this way, the use of PASEK Dunite allows increasing the homogeneity structure of sinter, reducing the percentage of return fines and improving the Sinter productivity.

Oct 30, 2017

By Günther Staudinger

Danieli Linz Technology has been honored at 4.1.2013 with the first contract for the exchange of a 350 t BOF converter for ArcelorMittal Poland Dabrowa Gornicza on a turnkey basis. This paper describes the new design features of this converter based on the development of a new Danieli converter suspension system. The issue was to install a new converter (incl. trunnion ring, suspension system and bearings) with maximum volume but keeping most of the existing equipment unchanged. So, the big tilting drives on both sides had to be reused and the existing foundation, pedestals as well as the bearing distance had to be maintained. Further on the welded coreequipment (vessel shell, trunnion ring, pedestals, slag shields, etc.) was manufactured in-house within the pressure vessel division of Danieli Thailand. Due to the huge dimensions of these parts the delivery had to take place in parts which had to be welded together on site under full production conditions of the steel plant. But also the erection had to be applied under this condition. Additionally the main support bearings, parts of the screening (doghouse) as well as an upgrade of the existing relining machine had to be delivered.

Jul 29, 2018

By Cristina Escudero Martinez

The purpose of the Basic Oxygen Steelmaking (BOS) is to refine the hot metal produced in the blast furnace into raw liquid steel, which may be subsequently refined in the secondary steelmaking shop. Appropriated fluxes for the BOF could require low melting point to reduce the energy consumption, to reduce the energy to fluidity the slag at lower temperature and to melt at lower temperature than steel. It is necessary a good Tumble test result and the fluxes do not generate fines which could obstruct the blowing plugs, so we would have a homogeneous flux. A homogeneous chemistry that allows to control the basicity (Si and MgO levels) and a high absorption characteristics to combine the flux with P, S, Si, etc. are necessary. PASEK Dunite is an ultramaphic rock exploited in the north of Spain with a basic chemical classification being olivine and serpentine its principal minerals. It is formed by orthopyroxene, clinopyroxene and olivine in variable proportion. Dunite is a very homogeneous and hard stone. The main characteristics are: High hot and cold resistance to mechanical stress (shatter / crushing / abrasion), softening and melting points of a flux, not a refractory material, large porosity which is increased more than 20% when dunite is heated at BOF process temperature, and high absorption level, and stable components with low melting points. PASEK Dunite is a good flux in BOF process and its use is recommended if the BOF process produces pig iron with low Si content, generates high levels of slag and it is necessary maintaining the basicity index and the MgO amount and with high value of hot metal ratio (high amount of phosphorus to remove).

Aug 16, 2017

By Antonio Augusto Gorni, Kenji Camey, José Herbert Dolabela da Silveira

Recently several studies have been developed on the use of microalloyed steels with low Mn content (below 1%) in the controlled rolling of heavy plates for the manufacture of pipes. However, this novel concept of alloy has peculiarities in its thermomechanical processing. Lower Mn contents should lead to the acceleration of NbCN precipitation kinetics during rolling, leading to a reduction in the soluble Nb content in austenite that delays its recrystallization by drag effect. This fact, plus the heavy and fast passes applied under virtually isothermal conditions in a heavy plate rolling mill with high power, increases the risk of partial recrystallization during the finishing stage of the controlled rolling, since strain hardening of austenite becomes significant and the interaction between precipitation and recrystallization is increasingly delayed. The objective of this study was to analyze the evolution of mean flow stress during the finishing stage of controlled rolling in these low Mn, high Nb microalloyed steels, in order to better understand the metallurgical mechanisms acting during this process and identify conditions that allow full compliance with the requirements of this product class.

Oct 1, 2019

By Eleir Mundim Bortoleto

A finite element modeling approach was developed to study adhesion phenomena during the unidirectional contact between a two-dimensional plane-strain square and a flat slab. Surfaces were metallic or ceramic, different pairs of materials were analyzed and their adhesion was considered by means of a FORTRAN subroutine (DLOAD), which was connected with commercial finite element code Abaqus and provided surface attractive forces based on the Lennard-Jones interatomic potential. Adhesive loads were considered both during approximation and separation of the surfaces. During the separation step, material transfer between surfaces, due to adhesion, was modeled by means of damage initiation and propagation at the flat slab. The parameters considered in the simulations were normal load, chemical affinity and system size and the different conditions were analyzed by comparison of the interaction forces during approach and withdrawal. This work also presents detailed descriptions of: (i) the evolution of energy dissipation due to adhesion hysteresis, (ii) the formation-growth-breakage of adhesive junctions and (iii) the evolution of stress distribution during the process. Results have indicated that chemical affinity between the bodies in contact is more relevant for adhesion than the applied load. Besides, smaller asperities are less prone to promote adhesive wear, but they may be subjected to high stress concentration effects.

Jul 31, 2018

By Renata Cristina Teixeira

The lubricant oil is a complex mixture of different basestocks and additives. Engine oils evolved from the use of pure mineral basestocks back in the early years of automotive industry to the advent of synthetic, fully formulated, low ash lubricants. This evolution was driven by a number of factors, such as new engine designs, extended durability needs, increased fuel economy needs, environmental concerns, feedstock prices and availability and legal issues. This paper uses technology prospecting on literature and patents databases to allow an investigation on the historical evolution of engine oils. Main basestocks (mineral, hydrotreated, polyalphaolefins, esters) and additives (antioxidants, antiwear, friction modifiers, detergents and dispersants) are characterized according to their research effort. Technology prospecting data is crosschecked against the evolution of engine oil classes, allowing an analysis of how the main drivers push the development of lubricant oil quality. A research effort was identified in late 1990’s until mid-2000’s and related to the adoption of chemical limits for lubricants. Different patterns for the articles and patents publication account for the high value technological knowledge has in this industry. Technology prospecting is seen as a useful methodology for the understanding and forecast of lubricant technology movements.

Jul 31, 2018

By Wujian jun

In the process of wire rod production, the rolled wire products must be cooled from the red-hot state to the normal temperature state. How to cool the wire rod after rolling is one of the key links of product quality control in the whole wire rod production process. In this paper, combined with the closed-loop transformation project of controlled cooling temperature of Xuanhuan iron and steel group co., LTD., the closed-loop related controlled cooling equipment (including water cooler, valve table, etc.), nozzle layout and process layout of water tank, and closed-loop software control system of controlled cooling temperature of high-line are analyzed and designed. Closed-loop system design USES temperature of cooling water cooling and water cooling two temperature closed loop regulating circuit, through temperature feedback and feedforward to achieve the uniformity of temperature adjustment, in order to prevent occur due to temperature closed loop control function with the phenomenon of a steel before and after the temperature difference is bigger, system Settings have "absolute temperature regulation" and "relative temperature regulation" selection mode. The system has a self-learning mode, which can modify the temperature feed forward formula. In addition, this paper takes the hard wire 82B rod as the test object, and studies the process parameters and the comprehensive mechanical properties of the rod before and after the water cooling system reform. The research results show that the temperature closed loop system, can ensure the rolled piece temperature control precision of plus or minus 10℃, enhances the stability of wire rod cleaner performance. It can reduce water consumption by about 186m3/h and improve the utilization rate of cooling water.

Oct 1, 2019