Search Documents

By Cristiano José Scheuer

The effect of low-temperature plasma carburizing treatment on the micro-abrasive wear resistance of AISI 420 steel was investigated by mean of a CSM Calowear ball-cratering equipment. Carburized samples were treated at temperatures of 350, 400, 450 and 500°C for a fixed time of 12 h, using a gas mixture containing 99.5% (80% H2+20% Ar)+0.5% CH4. Micro-scale abrasive wear tests were conducted with a 25.4 mm AISI 420 steel sphere, using an abrasive suspension of alumina (Al2O3) with particle size of 1 ?m (abrasive concentration of 0.11 g/cm³). The contact normal force, abrasive flow and ball rotation speed were fixed at: 0.5 N, 0,2 drop/s, and 120 rpm. The wear craters were analyzed using a confocal laser microscope, Olympus OLS 3000. The wear analyses were performed for test times of: 30, 60, 90, 120, 180, 360, 540, 720 and 900 s (equivalent sliding distance: 0.84, 1.68, 2.52, 3.36, 5.04, 10.09, 15.14, 20.19 and 25.23 m, respectively). The results indicate that the wear coefficient in the outer layer and in the diffusion layer are different, being lower in the latter. It was also verified that the wear coefficient on the outer layer region decreases with increasing treatment temperature in the range of 350 to 450 °C, and increase again for 500ºC. The diffusion layer wear coefficient is similar for all the carburized samples. Finally, for all studied conditions, the analysis of the wear craters surface indicates the occurrence of grooving and micro-rolling abrasion wear modes.

Aug 8, 2018

By Juarez Linhares

A mini sinterização processo JL patenteada sob o número PI-9202973-6, é caracterizada por soprar o ar pelo fundo da panela, dispensando o uso de grelhas, caixa de ignição além de proporcionar um baixo consumo de energia elétrica, o que se traduz em vantagens técnicas e econômicas ao processo de sinterização.

Aug 16, 2017

By Carlos Alberto Mourão, Robson Martins, Letícia Madureira Moreira, Hélio Braz Loss, Joilson Moreira Ferreira da Silva, Edilson Simões Cavalieri, Mauricio Ferreira Coelho

O conversor AOD-L é de uso exclusivo para a produção de aços inoxidáveis na Aperam South America. Entre janeiro a julho de 2018, o consumo de FeSi estava acima do orçado, acarretando em perda de gestão para a Aciaria. O aço inoxidável AISI 304 representa 50% da produção da Aciaria na rota duplex (sem uso do VOD), portanto, esse projeto teve como objetivo a redução do consumo da liga de FeSi no AOD-L para o aço AISI 304. Essa redução foi possível através da utilização da metodologia Lean Six Sigma na qual a causa raiz foi identificada e as ações implementadas o que permitiu uma maior estabilidade operacional, além de aumentar a competitividade da Aperam South America frente aos demais produtores mundiais.

Oct 1, 2019

By Roberto Balarini Junior

Tribological behavior of Si3N4 balls sliding against Al2O3 discs in water was investigated by studying the influence of parameters such as initial surface roughness and circular axial run-out of the discs. The objective was to relate these parameters with the occurrence of the phenomenon known as ultra-low friction coefficient (ULFC), which is characterized by µ < 0.01, including the correlation with running-in duration. As a general trend, greater initial surface roughness and circular axial run-out resulted in greater running-in duration. In addition, it was verified that a mixed lubrication regime (hydrodynamic and boundary) is required to guarantee the occurrence of ULFC by comparing the calculated minimum film thickness with the composite roughness of the worn surfaces. Also, ICQ-OES analysis of the water after the tests indicated that a silicon concentration greater than 1.3 mg/l should be fundamental for the occurrence of µ < 0.01.

Jul 31, 2018

By Elson Renato Santos Souza, Ricardo Pondé Weber, João Carlos Miguez Suarez, Sergio Neves Monteiro, Suzane de Sant’ Ana Oliveira

Foi estudado a influência do aporte térmico, de soldagem, sobre a resistência balística de um aço de alta dureza (HHA) temperado e revenido (HHA), utilizando o processo de soldagem a arco. O aço HHA, temperado e revenido, foi caracterizado por análise metalográfica, ensaios mecânicos e ensaios balísticos. Os resultados mostram que o aporte térmico da soldagem teve influência significativa nas propriedades mecânicas da Zona de Fusão (ZF) e da Zona Termicamante Afetada (ZTA), ocasionando mudanças na resistência balística. O melhor desempenho balístico do material soldado foi obtido para a soldagem de baixo aporte térmico.

Oct 30, 2017

By Alexandre Medeiros, Bruno Aquino Rocha, Evaldo Nogueira, Marcus Valério Magnago

Este artigo tem como finalidade demonstrar o cenário evolutivo da expedição ferroviária de produtos siderúrgicos da ArcelorMittal Tubarão, focado na eficiência operacional e no atendimento à Clientes. Neste documento, apresentaremos a estrutura de pátios e equipamentos, o status anterior do “share” de expedição nos modais terrestres e os motivadores do processo de mudança. Em seguida, iremos apresentar as melhorias e inovações implantadas em nossos processos internos e externos, da cadeia logística de atendimento à Clientes. Ao final, demonstraremos a evolução da participação do modal ferroviário no “share” de expedição, bem como os ganhos capturados através da elevação dessa participação.

Oct 1, 2019

By Helênio Resende Silva Júnior

Arcelor Mittal Asturias coking plant at Gijon works, Spain, is undergoing a complete modernization of the whole coke making complex. In this context, Gijon has to be considered a brownfield project, where Paul Wurth has been awarded with the engineering, supply of key equipment as well as erection and commissioning supervision services for the rebuild of two coke oven batteries the modernization of the adjacent by-product and relevant waste water treatment plants. Main objective of this paper is to present the technological improvements introduced by Paul Wurth in the rebuild of a modern plant focusing on fulfilling all the recent environmental regulations.

Oct 30, 2017

By Nathanael Wagner Sales Morais

Os aços maraging tem grande importância tecnológica devido sua aplicação nas industrias aeroespacial e nuclear. Uma das aplicações para esse material é a fabricação de cilindros de alta resistência pelo processo de estampagem profunda, logo o conhecimento da textura cristalográfica torna-se fundamental. Este trabalho investigou o efeito da laminação à frio seguida por um recozimento sobre a microestrutura, textura e anisotropia plástica no aço maraging 350. A anisotropia foi medida pelo cálculo dos coeficientes de Lankford e dos coeficientes de anisotropia normal (Rm) e planar (?R). Os resultados mostraram o aumento na deformação a frio gera um aumento na intensidade da fibra acompanhada de um aumento no valor de Rm. As análises metalográficas mostram que maiores reduções induzem à um precipitação intermetálica após o recozimento.

Aug 8, 2018

By Pedro Henrique Coutinho

Este trabalho teve como objetivo a redução do custo de transformação da Aciaria de Resende (Votorantim Siderurgia), visando à redução do Cash Cost do tarugo, ponto fundamental no atual cenário econômico da siderurgia brasileira. Para priorizar as ações, otimizar recursos e tratar o tema de forma estruturada foi utilizada a metodologia DMAIC na execução deste projeto. Como resultado houve redução no custo de transformação, alcançado por melhorias nas linhas de Energia Elétrica, Ligas, Escorificantes, Eletrodos e Outras Variáveis.

Aug 16, 2017

By Juciane Maria Alves

O aço inoxidável austenítico metaestável 304L, aço TRIP, é suscetível à transformação de fase austenita-martensita (??a’) induzida por plasticidade, a intensidade desta transformação é influenciada pela temperatura. Devido a isto, o objetivo deste trabalho foi induzir a transformação (??a’) através da laminação à temperatura criogênica, mais próxima da temperatura Mi do material. Para avaliação da transformação de fase utilizou-se a técnica de difração de raios-X e os resultados mostraram a obtenção de amostras 100% martensíticas. Devido à suscetibilidade deste material sofrer transformação (??a’) por deformação plástica avaliou-se a influência da preparação metalográfica (via polimento mecânico, químico e eletrolítico) sobre às análises quantitativas. O polimento eletrolítico se mostrou a forma mais promissora às análises quantitativas, pois permitiu a quantificação de pequena fração volumétrica de austenita retida.

Oct 30, 2017

By Tiago Silva Costa

Os tratamentos térmicos são um conjunto de operações que têm por objetivo modificar as propriedades dos aços e de outros materiais através de um conjunto de operações que incluem o aquecimento e o resfriamento em condições controladas. Os aços SAE J403 1045, SAE J403 1075 e DIN 100CrV2 são aplicados em diferentes setores industriais graças às diferentes propriedades que podem ser alcançadas através de tratamentos térmicos. Este trabalho visou caracterizar e descrever as fases formadas nos aços SAE J403 1045, SAE J403 1075 e DIN 100CrV2 após tratamentos térmicos de têmpera, normalização e recozimento pleno.

Aug 16, 2017

By Neiclésio Nunes Ibiapina

No forno elétrico a arco (FEA) é realizado a fusão da carga metálica composta de sucata, gusa sólido ou líquido, fundentes e o aquecimento do banho líquido utilizando energia elétrica e química. O balanço correto dessas energias e a escolha adequada das matérias primas são fatores que determinam a otimização da eficiência energética e demais ganhos advindos. Para melhoria desses fatores foi utilizada a metodologia Delineamento de Experimentos (DOE) que permite estudar as variáveis do processo e a complexidade de suas interações, buscando solucionar problemas e melhorar a desempenho através de análises estatísticas. Este trabalho mostra os experimentos realizados no FEA da Sinobras objetivando otimizar a energia química do FEA para diferentes condições de carga. O resultado alcançado foi a redução no consumo de energia elétrica, no consumo de oxigênio, no power on e aumento da produção.

Jul 30, 2018

By Cermets

Ti(C,N)-based cermets offer good high temperature strength, perfect chemical stability, excellent wear resistance, and relativly better machinability. In the present work, the tribological behaviors of Ti(C,N)/SiC sliding pairs lubricated in water and seawater were evaluated using a ball-on-disk tribometer. The experimental results show that a relatively low friction coefficient (about 0.025) can be obtained when lubricated with artificial seawater at the sliding speed of 200 mm/s, while the date is about 0.2 in purified water. The wear surface profiles and the lubricants collected after running-in process for the high/low friction conditions were compared. In addition, the effect of salt molar concentration of the lubricant on the Ti(C,N)/SiC friction properties was investigated. It was found that the smooth and flat surface is the premise to gain the low friction. At the same time, the proper concentration of silica colloid, which is affected by the salt ions, is also an essential one. Moreover, the high sliding speed (200 mm/s) is beneficial to achieve low friction.

Jul 31, 2018

By Franco de Castro Bubani

Cu-base alloys (Cu-Zn-Al, Cu-Al-Be, Cu-Al-Ni), depending on their composition, have martensitic transformations that can be thermally or mechanically induced between a metastable structure called austenite and one or more metastable structures called martensites. In single crystals, depending on the specific composition of the alloy and the crystallographic orientation of the tensile axis, martensite-martensite transformations can be mechanically induced. The hysteresis associated to these martensite-martensite transitions is usually much greater than the one associated to the austenite-martensite transformation. Thus, martensite-martensite transitions are potential candidates for energy dissipation in a mechanical damper. Possible applications that would benefit from high hysteresis include seismic damping devices, dampers for satellites and the aerospace industry, defense and others. We present pseudoelastic cycling results of alloys submitted to different thermal treatments. Our conclusions highlight the fact that, under certain conditions, Cu-base alloys deliver better damping performance than commercially available SMAs and even the new Fe-base SMAs.

Aug 7, 2018

By Jeremy Fletcher

In today’s world, the requirement of Steel Producers to revamp and modernize their blast furnaces on-time, safely and with the latest technology is paramount. In addition they must meet the detailed design, construction and safety legislation and regulations, which can be different for the various countries around the world. Siemens MT is renowned for its ability to perform Blast Furnace rebuilds, relines and modernisations within extremely tight time frames and in a safe manner. Modular Blast Furnace construction concepts have been perfected to minimise project duration and plant downtime for furnace rebuilds. Safety and certainty are the keys for success. Siemens MT are constantly introducing new technologies into the market place including cyclone gas cleaning and triple external cone gas scrubber, along with step changes in technology such as dry gas cleaning and dry slag granulation. The economic environment and the continuing requirement for improved environmental performance, drive many of these innovations. This paper describes some of the latest rebuild reference projects of Siemens MT, along with the latest technical innovations installed on these furnaces, and some of the construction methodology used for a safe and secure rebuild.

Aug 1, 2018

By HaiWen Luo, Bin Hu

A ultra-high strength medium Mn steel with good ductility was designed and manufactured via the combination of warm rolling and V alloying, which produced not only the extensive precipitation of fine VC particles in both ferrite and austenite but also the bimodal size distribution of retained austenite (RA) grains. A substantial increase of yield strength up to 650 MPa was achieved due to the addition of V without deteriorating ductility. The coarse RA grains firstly transformed to martensite during yielding at the much higher stress threshold, followed by a significant work hardening due to dislocations multiplication, twinning-induced-plasticity (TWIP) and transformation-induced-plasticity (TRIP) in the ultrafine RA grains. The best combination of strength and ductility included 1.5 GPa ultimate tensile strength and 28% total elongation. This was achieved due to the sustainable TRIP and TWIP effects in the later straining stage resulting from the ultrafine austenite grains, the latter were reversely transformed from the recrystallized ferrite grains.

Oct 1, 2019

By Jean Viana Bahia, Antônio Adel dos Santos, Vicente Tadeu Lopes Buono

During cold rolling of Cr-Mo alloyed DP steel, considerable oscillation of thickness may occur. The literature points out that such occurrence is due to non-uniform cooling of the coil after the hot rolling process. Since the austenite transformation in this steel continues after coiling, the microstructure and, consequently, mechanical properties are very susceptible to natural variations in cooling rates associated with distinct positions of the coil. The influence of coil cooling conditions on thickness oscillation during cold rolling was evaluated in this work by using both industrial experiments and dilatometer tests. It was verified that an industrial coil presented large variation of mechanical properties associated with its heterogeneous microstructure. Consequently, thickness oscillation occurred during cold rolling. Dilatometer tests simulating hot run-out table and coil cooling showed that the austenite transformation is very slow under small cooling rates that occur after coiling. Thus, the slow transformation rate makes the coil very susceptible to environmental conditions around it during its natural cooling and is responsible for variation in mechanical properties of the coil. To ensure the formation of a more homogeneous microstructure in the whole coil, it is necessary either to make use of technologies that improves the cooling uniformity or to adjust the steel alloy design. The latter alternative has been done with relative success by using conceptions with lower amounts of Cr and Mo.

Oct 1, 2019

By Guilherme Liziero Ruggio da Silva

Uma marcha estável do alto-forno (AF) está ligada à consistência das propriedades químicas, físicas e metalúrgicas das suas matérias-primas (MP), especialmente, as do coque. As propriedades do coque são reflexos das propriedades dos carvões que lhe deram origem. Em termos de propriedades ligadas à natureza do carvão, a qualidade do coque é bastante influenciada pelo rank dos carvões, que compuseram sua mistura, ou seja, quantidades de macerais reativos e inertes, bem como suas propriedades coqueificantes, que é, exatamente, a habilidade inerente aos carvões aglutinantes de quando aquecido, amolecer, tornar-se plástico e solidificar em uma massa coerente. Neste contexto, o presente trabalho se propõe a evidenciar as mudanças no modelo de britagem de carvões da Gerdau Ouro Branco, bem como a operacionalização do padrão criado. Após a implantação, verificou-se a elevação de 1.8% em DI.

Aug 17, 2017

By Delio Amorim

Industry 4.0 concepts is the new biggest challenge on the industry nowadays and every company in every industry in every part of the globe is looking to implement this somehow on their factories and machines. To do that on the newest long rolling mills, that brings already onboard state-of-the-art technologies, is for sure a challenge of machinery builder industry, but how to become the long rolling mills built on 70’s, 80’s or 90’s part of this innovation process and connected to the new trends? This is the main mission here, to show some examples of applications that goes in this direction.

Oct 1, 2019

By Luiz Alberto dos Santos

. In this work, samples of the alloy with composition of 50.9 % at. Ni were machined and were subjected to hot tensile test, after the machining all the samples were solubilized so that all were in the same condition during the hot tensile test. The hot tensile tests were performed between the temperatures 350-650°C and the yield stress were between 800 and 597.1 MPa and area reduction between 17 and 75% with respect to the initial area. The test at 350°C shows a fragile fracture characteristic while the hot tensile test above this temperature showed a predominantly ductile fracture. The fragile fracture is evidenced by the river marks that are characteristic of this type of fracture, because in this condition does not promote much plastic deformation. The higher temperatures present ductile fracture, because present the dimples that also characterize this type of fracture. This work shows the temperature relationship in the mechanical properties, more specifically the hot tensile test, in the NiTi alloy.

Oct 30, 2017