Search Documents

By Yates C, Gillie E. W, Finucane K. J

During the year 1940 a complete investigation was made of the whole of the stoping operations throughout the Great Boulder Mine and, as a result, it was decided to convert some of the existing shrinkage stopes into cut-and-fill stopes, and also to mine many of the more recently developed ore blocks by the latter method. The necessity for filling was due primarily to the structure of the ore blocks, the character of the walls and possible excessive dilution, but was influenced also by the grade of the ore-block and by the fact that cleaner mining can be carried out by cut-and-fill stoping.The comparatively few cut-and-fill stopes in operation prior to 1940 had been filled mainly with waste rock from development work, but as the amount of this material available, or likely to become available, would have been wholly inadequate for future operations, it was proposed to construct a system of passes to supply filling material from the surface.Owing to the distribution of the stopes, no central pass or system of passes could be devised which would service all the stopes satisfactorily.However, work was commenced on two passes, one designed to service the cut-and-fill stopes in the Eastern Section of the mine, and another to service those in the Western Section. It was realised that these passes could serve only a small proportion of the total number of Stopes (Figs. 1 and 2). During the progress of this work experiments were undertaken to test the possibility of using filtered tailings underground as an adjunct to the above scheme, but for various reasons these were only partially completed.Early in 1942 it was suggested by the Mill Superintendent that an attempt be made to fill with wet classified flotation tailings as practised at Mt. Lyell in Tasmania and at the Triton Mine at Reedy, West Australia. For the purpose of testing this, an experimental stope was prepared on the 309-ft. level, "X" Lode. This was 100 feet long and averaged 4 feet in width. Water-tight rearings were built at each end of the stope and waste rock fill was spread to a height of 6 to 8 feet above the timber. Used filter cloths were laid on top of the fill and brought a few feet, up the walls of the stope. A two-inch victaulic drainage line was then placed in position, the end passing through a hole in one of the bearings and thence to a sump. In the central portion of the stope two vertical pipes were brought up from this line. These were bored with one-inch holes staggered on opposite sides of the pipe, the vertical interval between each hole being one inch. The holes were then stopped with...

Jan 1, 1945

By Jr. Gabler

Methods for the direct spectrochemical determination of impurities at the parts-per-million level in tungsten metal and oxide are presented. Several published procedures were investigated and numerous modifications were made in establishing procedures with improved precision and extended lower levels of determinability. Details of standards preparation are presented, experimental work is described, and three preferred methods are described in detail. A germanium carrier-distillation procedure is applicable to the determination of 13 elements in tungsten powder; a silver chloride carrier-distillation procedure provides for the determination of 24 elements in tungstic oxide, and a sustaining ac arc method is applicable to 26 elements in tungstic oxide. The choice of methods to be used depends upon sample form, elements and concentrations to be determined, and the precision and accuracy required. The investigations reported here were undertaken to develop direct spec-trochemical methods with increased accuracy and precision to determine impurities in high-purity tungsten and tungstic oxide, to define the lower concentration levels of detectability and measurement for the common impurities in tungsten by direct spectrographic means, and to present the details of the developed or modified methods that have proved applicable.

Jan 1, 1965

The banded iron formations "jasper bars," jaspilites, banded hematite quartzites or banded ironstones, etc., as they have. variously been termed in Western Australia, constitute one of the most striking features of the Pre-Cambrian in this State. They occur in at least two distinct divisions of the Pre-Cambrian, viz., in horizons interbedded with quartzites, shales and thin bedded dolomite in the N~llagine (Proterozoic) Series; and amongst the Older Pre-Cambrian rocks, associated with the metamorphosed sediments of the Jimperding-Chittering Series, the Yilgarn Whitestone Series and the Mosquito Creek Series, and interbedded with metamorphosed basic lavas, tuffs and sediments of the Older prenstone or Kalgoorlie Series.In the Hamersley Ranges in the north-west of Western Australia banded ferroginous cherts are well developed amongst the horizontal sediments of Nullagine Age. These iron formations have recently sprung into prominence as they have been found to form the host rocks for important deposits of· blue asbestos. They are closely comparable with the unique crocidolite-bearing banded ironstones of the Cape Province, South Africa, and have been described elsewhere in some detail by the writer. (1) t .The banded iron formations with which it is intended to deal principally in the following pages, form most abundantly in the Central and Eastern Goldfields of Western Australia where they form portions of the Older Greenstone or Kalgoorlie Series of auriferous rocks. In these regions their chemical inertness and physical hardness provide considerable resistance to the agents of erosion and consequently they frequently stand out in strong topographic relief in otherwise monotonously flat or gently rolling country. These banded-iron formations have proved of considerable direct economic importance in the goldfields and in other portions of the State because of thei!! associations with 'gold, iron -and to' a lesser extent, manganese; whilst indirectly because of their peculiar nature, form and topographic prominence, etc, they have been of tremendous assistance to the field geologist both in the practical application of methods of geological mapping and in the' elucidation of geological structures. Finally, they have recently acquired a new importance in the specialised search for ore-bearing lodes or for structural information over areas of soil-covered country, as their form and composition make them ideal subjects for the use of either electrical or m!1-gnetic methods of geophysical prospecting.

Jan 1, 1941

By M. J. Collins

"Autoclaves were first used in the metallurgical industry in 1893 to recover alumina from bauxite. In the 1940s and 1950s, several high temperature and pressure processes were invented in the laboratory of Professor Frank Forward at The University of British Columbia, in parallel with advances in equipment and processes by the Chemical Construction Corporation. Sherritt Gordon Mines Limited enlisted these groups to help develop the nickel sulfide ammonia leach process that was commercialized in 1954. Autoclave processes that have since been commercialized include high-pressure acid leaching of laterites, zinc pressure leaching, and pressure oxidation of refractory gold feedstocks. RÉSUMÉ En 1893, l’industrie métallurgique est la première à utiliser les autoclaves pour l’extraction de l’alumine dans la bauxite. Dans les années 1940 et 1950, plusieurs procédés à haute température et à haute pression sont inventés dans le laboratoire du Pr Frank Forward de l’université de la Colombie-Britannique (UBC) ; parallèlement, la Chemical Construction Corporation fait de grands progrès en matière d’équipement et de procédés. Sherritt Gordon Mines Limited fait appel à ces groupes pour qu’ils aident la société à développer le procédé de lixiviation du sulfure de nickel dans de l’ammoniaque, commercialisé en 1954. Les procédés de lixiviation en autoclave commercialisés depuis incluent notamment la lixiviation acide à haute pression de latérites, la lixiviation sous pression du zinc et l’oxydation sous pression des matières premières de l’or réfractaire.INTRODUCTION Autoclaves are chemical reactors that are built to contain processes taking place at elevated pressure. They are used in metallurgical refineries throughout the world to take advantage of the increased reaction kinetics and different reaction products that can be obtained in aqueous systems above the boiling temperature at atmospheric pressure. The word autoclave comes from the French “auto” and the Latin “clavis” and literally means self-locking—that is, the core distinguishing feature of an autoclave is that it includes a means for pressure regulation (e.g., a pressure relief valve). Denis Papin (Figure 1a), one of the inventors of the steam engine, was the first to make use of a safety valve to control steam pressure. He is credited with inventing the autoclave in 1679. Papin’s “digester” (Figure 1b) was a type of pressure cooker that was originally used to liquefy bones. Most commercial autoclaves are horizontal, multicompartment vessels with mechanical agitation, as shown in Figure 2a; however, the steam-agitated Pachuca vessels used to leach laterite ore in Moa, Cuba (Figure 2b), are also classified as autoclaves according to the self-locking definition provided above."

Jan 1, 2018

By Rudi Podjadtke

In a short chronological review the development concepts and improvements in steel roadway support are shown. The successful standardization concept of RAG Deutsche Steinkohle and currently used support systems are important topics. The history of optimizing the material properties for the steel arch support with different alloys up to the tempering used today is discussed. The present-day application of the steel support is additionally presented. Today, it represents a system component of modern roadway support also for highly stressed roadways. In addition to the yielding roadway arch support, this overall system - the combination support - consists of the additional components of a rockbolting system and concrete backfilling. The comparison of the application areas for each individual partial system with the overall system illustrates its high performance capability. Actual practical experience with the state of the art typed steel arches are pointed out exemplarily. Understanding the complete system permits the selection of the economically optimal support for all conditions.

Jan 1, 2008

By Edward Keller

The work covered by this report was undertaken at the request of Dr. J. A. Holmes, late Director of the Bureau of Mines, to whom the writer had been recommended by C. W. Goodale and E. P. Mathewson, of Butte and Anaconda, Mont. The director's offer was accepted for the honor it conferred and for the useful results that might be promulgated by the work in the technical field covered. The investigation was facilitated by permission to visit various works and sometimes by contributions of important definite information on a given subject. It is therefore with pleasure that acknowledgment of courtesies is made to the following corporations and gentlemen: Anaconda Copper Mining Co., Raritan Copper Works, Baltimore Copper Smelting & Rolling Co., United States Refining Co., American Smelting &, Refining Co., B. B. Thayer, A. C. Clark, A. L. Walker, William H. Peirce, E. A. Cappelen Smith, H. H. Alexander, F. C. Newton, S. Rolle, R. W. Deacon, N. W. Pierce, O. C. Martin, C. N. Sappington, James K. Thomson, W. G. Derby, and the assistants of the writer, K. W. McComas and W. L. Raup. In this report considerable space has been devoted to general and theoretical principles on the ground that under modern conditions the best results in any field of activity can be attained only with the a. id of an adequate knowledge of the best theories underlying the practice. The diffusion of such knowledge in the field of sampling metallic metallurgical materials appears to have been quite insufficient, and it is felt that when the principles involved are once thoroughly comprehended their universal application will be appreciated, so that it will make no difference whether pig iron or gold bullion is offered for test. It may further be noted that a discussion of the theories underlying practical methods is placed under the caption "Practical Sampling," with the idea that no one can be a practical sampler unless he is capable of analyzing his methods. No attempt has been made to advocate any one method, but it is hoped that the analyses of all of the methods in use will show where each may be correctly and safely applied. The fact that it is possible to demonstrate the theoretical correctness of several methods indicates the invalidity of the claim that any single one of them is the standard.

Jan 1, 1916

By Davorin Kolic, Harald Wagner

Conventional ground support in accordance with latest state-of-the-art considers proper preparation of geotechnical investigation, structural design, observation during construction and fair risk sharing documents. Depending on the ground, there are different means and methods, reflecting different experiences. The paper is presenting ground support concepts, as mostly used in Europe during the past three decades. It discusses the use of anchors as well as the use of steel arches respectively combinations. It also discusses different applications of plain shotcrete, respectively fibre reinforced shotcrete. As excavation sequence is a major input to create the ground arch, the paper discusses also criteria to create closed ring conditions. Finally deformation criteria will be presented with case histories in order to control stability of the structure.

Jan 1, 2001

By Eric L. Trist

The objective of this contract was to review the results of the Rushton Mining experiment in work organization and design, to explore the extension of knowledge gained from Rushton to other underground coal mines, and to conduct a search for a potential mine site for a demonstration project. The primary focus of the contract was on a search process to provide the research team with the opportunity to evaluate the different potential experimental sites, in order to select one or more with the highest potential for success. This search process also provides the various levels of union and company officials the opportunity to fully understand the context of the research before making a decision on whether to participate. While the search project failed in its attempt to locate a specific mine site, the research team believes that this is not a rejection of the actual project but rather extreme caution because of the uncertainty within the UMWA.

Jan 1, 1978

By S. Lolon

Spontaneous combustion in underground coal mines has become a serious problem particularly in the caved area (gob). Recent statistic has shown that approximately 17% of total 87 underground coal mine fires in the United States are attributed to spontaneous combustion (De Rosa, 2004). Spontaneous combustion results from a self-heating process in exothermic conditions. The accumulated heat, if not removed, is conducive to the rapid increase of temperature and may result in mine fires or explosions. It is well accepted that the interaction between oxygen and coal substances is the main cause for spontaneous combustion, while other factors such as pyrite, moisture, and bacteria play a secondary role to the self-heating of coal. Therefore, only coal oxidation is considered in this study. Coal oxidation occurs as coal comes into contact with air. This process involves complex phenomena in terms of heat transfer, chemical surface absorption, and energy balance related to inherent properties of coal (Wang et al., 2003). For simulation purpose, overall reactions can be simplified as suggested by Mitchell (1990): C + O2 CO2 + heat [65°- 94°C] (1) CO2 + C 2CO + heat [100°- 150°C] (2) Stoichiometric reactions (1) and (2) show that 2.66 grams of oxygen are required to oxidize 1.0 gram of carbon. Once the temperature exceeds 100°C, the reaction has little chance to stop. The crucial step in reducing spontaneous combustion risk is locating the ignition point of spontaneous combustion (hot spot). This information is useful in the effort of developing a preventive method effectively. In this study, this was conducted based on the best gathered information: ventilation surveys conducted in an existing longwall mine located in the western US; the laboratory experiments performed on a physical gob model; and the CFD models to investigate the flow behavior in the gob, the oxidation of coal, and heat transfer phenomena. The hot spot location is determined as a function of oxygen concentration and gob temperature. The critical values are the following: 5% (by volume) for oxygen and 100°C for gob temperature. CHARACTERISTICS OF GOB MATERIAL AND MODELS Permeability Concept Permeability is one of the key parameters in any study dealing with porous medium. This is determined by particle size and the ratio of void volume to the total volume (porosity) of porous medium. This relationship is known as the Carman-Kozeny equation (Scheidegger, 1957) and is given mathematically as [ ] where k* = theoretical specific permeability, m2 dm = the mean particle size, m n = porosity However, permeability tests with various particle sizes were carried out at the University of Utah?s ventilation model (Figure 1) to verify this relationship. These tests indicated a necessity to modify this theoretical relationship. A factor of 0.898 was obtained to make up the different between theoretical permeability and the experimental one. The modified version of (3) is given by: [ ] This equation is used to determine permeability of the simulated mine gob throughout the study. [ ] Mine Gob Material The gob is represented by zones filled with material of given size distribution. For physical measurements and CFD simulations, the material used were crushed rock and coal. Due to compaction, three different characteristics of gob material were used in the model: unconsolidated, semiconsolidated, and consolidated. In the real condition, the largest coal-rock particles are more likely to be located in the area behind the shields. This material is freshly broken and unconsolidated. The size of these broken particles is based on a study carried out by analyzing images taken from the area behind the shields in three coal mines in the United States (Pappas and Mark, 1993). The results have shown that the mean size of materials behind the shields is about 1.22 m. The permeability associated with this size was then obtained from (4) and permeability tests. This was 4.68 x10-7 m2. For semiconsolidated and consolidated zones, due to the lack of experimental data, these were determined through CFD simulations. These simulations were designed by assigning a permeability of 3.15 x 10-8 m2 for consolidated zone and 7.98 x 10-9 m2 to the other zone. The airflow pattern in the gob assigned with given permeabilities was expected to follow the experimental distribution (Brunner, 1985). The mean particle sizes for the semi-consolidated and consolidated zones were 0.02 and 0.006 m, respectively; smaller than those of the unconsolidated zone. Figure 2 shows the 3D view of permeability changes in the gob.

Jan 1, 2009

By J. Brian Anderson

Jointed micropiles were investigated to support bridge foundations where shallow rock was present. In this application, micropiles would have some amount of unsupported length, and would be subject to nominal lateral loads. Five lateral load tests were conducted on micropiles to demonstrate the impact of casing joints and rock socket embedment on lateral behavior. Load tests were simulated with FB-Multipier, a hybrid-finite element program for analysis of deep foundations, for proper design of the loading apparatus and instrumentation. The micropile sections were 2 m (6.56 ft) long, 273 mm (10.75 in) in diameter, 13 mm (0.5 in) thick walled, with a 50-mm (2-in) long threaded joint. Micropiles were made of one to three casing sections and were embedded 0.3, 0.6, 1.5, or 3.0 m (1, 2, 5, or 10 ft) into rock. In each test, two identical micropiles were pulled together using a simple frame until the weaker pile failed. All micropiles were instrumented with inclinometer casings while two contained strain gages at 0.76 m (2.5 ft) intervals. Load and displacement were measured at the pile heads. Tests showed the embedment of 0.6 m, 1.5 m, and 3.0 m (2 ft, 5 ft and 10 ft) sufficiently carried lateral loads over 180 kN (20 tons). The piles embedded 0.3 m (1 ft) were not able to maintain lateral load. In general, all micropiles tested to failure exhibited a brittle failure mode where there is small lateral deflection followed by a sudden failure at the casing joint. This was demonstrated in three of the load tests. In most cases, the micropiles were stiffer and stronger in the load tests than originally predicted numerically. The final test, where piles were not loaded to failure, verified that embedding vibrating wire rebar strain meters in the grout captured the bending moment profile of the micropile. The results showed the maximum moment in this case being carried directly across the threaded joint as predicted by the preliminary models. The results of these tests were used to calibrate the FB-Multipier numerical model. Using a load test that included bending strain measurements for a match, the soil properties were adjusted to produce reasonable matches for all of the load tests.

Jan 1, 2011

By Dan A. Brown

The New Mississippi River Bridge (MRB) employed conventional design-bid-build procurement, but the bidding process included the opportunity for pre-qualified bidders to develop and propose confidential Alternative Technical Concepts (ATC?s) for evaluation and approval in advance of bidding. The ATC process provides a mechanism for value-engineering prior to bid, with incentives and opportunities for both the owner and the bidding contractor. The contract described in this paper is for the river bridge composed of a cable-stayed crossing with two pylons and the anchor piers on each side of the river. The Massman-Traylor-Alberici (MTA) team developed a re-designed foundation system for the main pylon and anchor foundations which utilizes their equipment and experience along with field load test measurements to optimize the foundations. The paper describes the experience with the use of the pre-bid ATC process on the project from the perspective of the bidder, and outlines some of the benefits and limitations of this concept with respect to foundation design and construction. Some keys for success are identified and impediments to the effective implementation of the process are described.

Jan 1, 2011

By A. Tylczak, C. Norman, C. Shook, S. Loif

"There are a lot of good reasons to manage energy use at mining operations. Optimizing process energy use reduces operating costs. Tracking energy use can help identify unplanned process changes or malfunctioning equipment early, which allows problems to be corrected promptly.Sacré-Davey Engineering in Vancouver has performed over 50 Energy Management studies for various industries including: mining, pulp and paper, oil and gas, etc. Energy Management programs can be used to identify energy reduction opportunities, assess project feasibility, complete equipment selection trade-offs, as well as to monitor and manage energy costs. Benefits of energy management programs are reduced energy costs, reduced maintenance, and increased plant automation. Additionally, energy management can provide access to utility incentive funding and quantify savings which can greatly improve the return on investment of potential projects.Energy management studies are funded by many Utility programs across Canada. There are various programs available for existing plants energy audits, project feasibility studies, new plant design reviews and energy monitoring and targeting, etc. There are capital incentives available which can significantly reduce payback period.This paper discusses how energy management can be used to support mill/mine operations groups, maintenance programs, as well as expansion or green field projects. This paper will also provide an overview of Canadian Utility companies programs and how they can assist mining companies.IntroductionThere are a lot of good reasons to manage energy use at mining operations. Optimizing process energy use reduces operating costs. Tracking energy use can help identify unplanned process changes and identify malfunctioning equipment early, which allows problems to be corrected promptly."

Jan 1, 2015

By K. Biswas, S. Iverson, S. J. Jung

Computer modeling of rock flow in ore passes is being investigated and compared using MSC Soft-ware’s Working Model 2D1 (WM2D) and Itasca Corp.’s Particle Flow Code in Two Dimensions (PFC2D). This work is being carried out by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health to determine the usefulness of computer modeling to improve ore pass design. The types of tests included pendulum tests to validate WM2D simulations and simulated single-rock drop tests in both WM2D and PFC2D to understand their contact models. Simulated rock impacts at the ore pass chute and the use of inclined ore passes and doglegs were investigated in both programs. A PFC2D simulation showed that dynamic loads at the chute gate were reduced significantly when a dogleg transition was used, and simulations in which the ore pass was inclined showed significant reductions in chute impact loads compared to simulations of a vertical ore pass. A released hang-up was simulated using PFC2D.

By F. Habashi

"The rare earths industry started in Austria in 1887 by Carl Auer von Welsbach (1858-1929) Professor of Chemistry at the University of Vienna. The process was based on monazite sand transported from Brazil as shipping ballast free of charge. This made possible producing thorium, cerium, and other rare earths at a low cost, thus permitting the growth of the industry. However, once the Brazilian authorities realized the strategic importance of the sand, shipping was stopped. Brazil then started its own processing of the sand in 1949. The background for Auer’s work, the role of Robert Bunsen in Heidelberg, and the invention of the spectroscope will be presented. INTRODUCTIONHeidelberg on the Neckar (Figure 1) was the meeting place for chemistry students from all over Europe in the nineteenth century. Her university founded in 1386 had already a famous professor of chemistry and medecine in the Faculty of Medicine by the name Leopold Gmelin whose three - volume Handbuch der theoretischen Chemie appeared in 1817-1819, that became later a multi-volume monumental work. As successor to Gmelin came Robert Bunsen (Figure 2) in 1852 who made this university town the Mecca of chemistry students. One of his students, the English Henry Roscoe (1833-1915) who became later a distinguished professor in Manchester, described him as follows: ""As an investigator he was great, as a teacher he was greater, as a man and a friend he was greatest""."

Jan 1, 2012

By S. G. Tsimas, A. K. Moutsatsou, G. K. Parissakis, M. A. Komiotou

For Greek kaolin producers, a considerable proportion of whose output is from deposits containing more than 4 wt% Fe2O3, the colouring resulting from iron oxide impurity represents a serious problem that necessitates upgrading of the ore to meet commercial specifications. Autoclave leaching with oxalic acid for 1 h at 120 degrees C and 5-6 bar was shown to reduce Fe2O3 by up to 90% without affecting the structure of the kaolin, which maintained its physicochemical properties. The iron oxalate product can either be removed from solution or precipitated as iron hydroxide with recycling of the oxalic acid

Aug 1, 1995

By W Akpan

The Royal Bafokeng community in South AfricaÆs North West Province represents a unique case in Sub-Saharan Africa in terms of its positioning in the natural resource economy. It receives royalties directly from mining firms for the extraction of Platinum Group Metals, which include platinum, ferrochrome, rhodium and palladium. In 2007, royalty income of about R290 million (approximately US$32.2 million) was reported. Such direct revenues have enabled the community to invest in educational, medical and other social infrastructure, thus complementing governmentÆs social provisioning efforts. Indeed, the Bafokeng community owes its present-day modernisation efforts to mineral rights, and in particular, the legal-institutional arrangement that has enabled it to play an active role in South AfricaÆs lucrative extractive economy. However, the distribution of platinum wealth in this community is not only uneven, but also appears to have had little impact on the broader socio-economic conditions in the community. Despite claims by community leaders of heavy investment in education and skills development, the community continues to be faced with very high levels of unemployment, illiteracy, sprawling informal settlements, poor access to medical facilities and malnutrition. This paper examines the sociological paradoxes and contradictions thrown up by the approach adopted to involve community members in the mobilisation of mining royalties for developmental ends. The central argument is that the current æmodelÆ contradicts the communityÆs stated goals of using platinum wealth to drive up broad-based development and modernisation. This is mainly because it leaves out the vast majority of community members, who are uneducated and unskilled. The core analysis is based on pilot data from an ongoing study in the Royal Bafokeng community.

Jan 1, 2009

By James Ransford Dankwah

This work investigates the effect of waste plastics addition on the reduction of iron oxide by sawdust. Composite pellets of iron oxide containing sawdust (SD), high density polyethylene (HDPE) and blends of SD/HDPE were fired under argon in a horizontal tube furnace at temperatures between 1300 and 1500 °C. Reduced samples were weighed after 10 minutes of reduction and the extent of reduction was calculated from the measured oxygen contents of the compact. The results showed improved extent of reduction when SD was blended with HDPE. The highest extent of reduction was achieved at SD:HDPE ratio of 2:3.

Jan 1, 2014

By A. Korchevisky

Environmental self-monitoring is one of the advanced approaches for industrial sustainability programs. Organization for Economy Cooperation and Development (OECD) defines self-monitoring as ?the system of organizational and technical measures put in place and financed by [the] regulated subject? in order to ensure their compliance with regulatory requirements?1. Self-monitoring is beneficial for industrial operators, communities, and governments. Industrial companies use self-monitoring as a central element of their compliance management that allows them to fulfill their duties, obligations, and to avoid citations. When industries control their emissions and ensure workers are not exposed above the regulated limits, communities are better. It is impossible for an EPA, OSHA, or MSHA inspectors to be close to every emission source or workplace full-time. It is much more effective for industries to self-monitor, under due supervision. Occupational conditions are a very important part of industry and health and safety self-monitoring should be highly prioritized. In this paper we will research the regulatory basis and best practice of occupational self-monitoring. We will show that not only is self-monitoring a vital element of an occupational health & safety management system, but that you need a management system for affective monitoring.

Jan 1, 2012

By Ching-Liu Wu, John Hawley, Andrew H. Liu, James Chai

The Hatch Mott MacDonald/Bechtel Joint Venture team is designer and construction manager for the 5.25-mile Tunnel Segment of the overall 16-mile Silicon ValleyRapid Transit Project, which extends the existing Bay Area Rapid Transit (BART) system southward from Fremont to San Jose. The Tunnel Segment includes twin boredtunnels, mined cross passages, and three deep station excavations situated in highlyvariable ground, high ground water table, and a dense urban setting with high-risebuildings adjacent to the largest excavation. This paper will discuss design challengesthat have arisen with the excavations and the proposed solutions.

Jan 1, 2007

By D. A. Trotter, G. J. Goddard

"This paper describes a method of deciding on various design parameters for a sublevel caving layout. Layout design curves are obtained from the output of a computer optimization program. The program uses mathematical relationships derived from the theory of gravity flow of material to optimize the large number of interdependent design variables which are involved.IntroductionIn the design of an efficient sublevel caving mining system, a large number of interrelated variables need to be considered. Although many papers discuss individual variables, very little exists in the literature to show how these variables interact to achieve optimum results. This can lead to trial and error in sublevel caving design, which can prove costly, particularly because sublevel caving is a mining method which requires integration with sublevels above and below. With no pillars being left, experimental stopes cannot be isolated for study. Unfortunately, the complexity of layout design and the costs associated with trial and error have caused many planning engineers to choose more tried and tested mining methods.Sublevel caving works best to extract low-value ore surrounded by incompetent rock. All phases of the mining method can be highly mechanized, allowing low operating costs and high production rates. Good safety records are achieved, as workers are always in 'good' ground and the method is regular, making it comparable to an industrial process."

Jan 1, 1981