Search Documents

By R. H. Eric, P. Taskinen, A. Bhalla, P. Halli

Sustainable development requires less energy consumption with lower carbon footprint. In this review the solid state reduction behaviour of three oxide ores using methane gas are briefly summarized based on experimental work conducted in our laboratories. The discussion concentrates mainly on mechanisms of the reduction studied through SEM-EDAX and X-ray diffraction techniques. Limited preliminary kinetic input is also mentioned. Iron ore containing titanium and vanadium could be reduced significantly in the solid state with methane-hydrogen mixture up to 400 °C lower than is needed in ordinary solid state carbothermic process. The reduction of chromite and manganese ores were possible similarly at lower temperatures with potential energy savings lower carbon footprint.

Mar 1, 2017

By R. Rajiv Srivastava

Brine leaching of a TSL processed zinc-plant residue (ZPR), containing 83.3% anglesite, has been investigated for lead recovery. A prior treatment of ZPR in acid solution did not show any significant effect of acid concentration in zinc dissolution. The study reveals that the solubility limits of PbCl2 is as an important factor with respect to the brine concentration and pulp density in lixiviant. The dissociated sulfate ions hinder the formation of PbCl2 on prolong leaching (above 60 min), while exhibiting the reverse solubility of lead as PbSO4. A 3-step leaching process could yield >92% leaching efficiency when the parameters were maintained as: 10% pulp density in a 250 g/L NaCl solution, 80 °C temperature, and 60 min time. This leaves the insoluble ferrite, sulfides and oxy-sulfates of zinc and lead in the final residue as revealed by the XRD characterization.

By Keizo Uematsu, Satoshi Tanaka, Nozomu Uchida, Anze Shui, Joaquin Lira, Cyril Lavelle, Midori Saito, Thierry Poirier

"Dispersed and flocculated alumina (non-spherical particles) slurries were prepared by pH controlling with HCL Spray-drying of these resulted in dimpled granules with a smooth surface and high density, and spherical granules with rough surface and low-density, respectively. Detailed characterization on granules and their compacts includes: SEM observation, density measuring (mercury porosimetry and Archimedes's Principle) and liquid immersion optical microscopy. Compaction of these granules originated a larger particles rearrangement in the samples made with the spherical granules than with the dimpled granules. This was verified through the orientation of alumina particles, which was pronounced in the compact made with the former granules.IntroductionOn immersing a ceramic powder in water, the surface usually acquires a charge by interaction with ionic species in solution. The charge is affected by pH and the electrolyte concentration of the water. 1 The dispersion in a slurry is achieved through the interaction of charges on the particle surface with the media. In the ceramic processing, especially in the process of casting, the dispersion of slurry has been one of the most important topics studied for many years. Recently the attention is paid on its role in the pressing. The granule characteristics are governed by the dispersion state of slurry. Takahashi et al2 , Tsubaki et al3 and Walker et al4 showed that the granules from dispersed slurry were dimpled and of high density, while granules from flocculated slurry were spherical and of low density. This variation in the granules characteristics should have a marked effect on the structure of compact.This paper presents the influence of the dispersion state of alumina slurry on the granules characteristics and also on the internal structure of compacts. Different dispersion states were elaborated by adjusting pH of the slurry. In this method, the particles are dispersed or flocculated only by the effect of surface charging, and thus some secondary effect such as the steric hindrance from an electrolyte dispersant is avoided. The characteristics of granules and compacts are examined with SEM, density measurements by mercury porosimetry and by Archimedes's Principle and liquid immersion optical microscopy. This novel microscopy provides various important information on packing structure of particles, such as their orientation. 5"

Jan 1, 2000

By Jonathan A. Paul

The most profitable companies in the world recognize that a huge competitive and financial power lies in their intangible assets. The competition to be in command of raw materials and markets is now waged more and more over the exclusive rights to new technology and ideas. The value gained from mining the innovation in your organization and protecting your intellectual property can be enormous. This paper will address the following topics: ? Understanding the connection between your competitive position and intellectual property ? Determining the value of your current portfolio and strengthening protection ? Converting knowledge into assets and adding value to the operation ? Litigation strategies to enforce your position and achieve your business objectives The presentation is designed for company executives and government managers who need to know how to identify and address core intellectual property issues that arise in the minerals, metals and materials extraction and processing industries.

Jan 1, 2006

By Fabio J. Esper, Wildor T. Hennies, Guillermo R. Martín-Cortés, Francisco R. Valenzuela-Díaz, Antonio J. Santana de Araujo, Maria G. Silva Valenzuela

Seeking to replace carbon-black as filler of rubber in the production of vulcanized goods, researchers from University of São Paulo have studied different materials types as minerals, vegetal or wastes agricultural and industry. Results of rubber composites filled with MA1 a waste of mineral treatment provided by Esper Industries are presented. MA1 was characterized through X-ray diffraction; Thermal analysis; Scanning Electronic Microscopy; and others laboratory methods. The composite and shaped masses were evaluated by these methods plus their mechanical properties such as tensile strength, elongation at break and hardness. Exceptional results were obtained in the mechanical properties evaluated, better than those obtained with the traditional carbon-black. Seeing the kind of material used as filler, it can conclude that the environmental benefit is present, as well as economic development, giving credibility to the use of these alternative material in replacement carbon black.

Jan 1, 2015

By John Anawati

Bauxite residue is an environmentally unfriendly byproduct of alumina manufacturing, produced worldwide in large quantities. This material contains 50– 100 ppm of scandium, a critical material for the production of stronger, weldable, corrosion resistant, and heat tolerant aluminum products. Aircraft manufacturers are particularly interested in Al–Sc alloys because of its ability to form weldable alloys that could potentially reduce aircraft weight by 15–20%. Because of its abundance and low cost, bauxite residue has the potential to be used as an efficient feedstock for valorization processes to recover its scandium content, while in turn degrading this problematic waste. In this project, we developed an efficient process to recover scandium and rare earth elements from a Canadian bauxite residue with high extraction yields, using industrially scalable and economical techniques. The process employs a modified version of sulfuric acid leaching and subsequent impurity removal by selective precipitation. This article outlines the current progress and design rationale in the development and optimization of this innovative and sustainable recovery process.

By Shin-ya Kitamura

Kinetic modeling is very important to understand steelmaking reactions. The coupled reaction model proposed by Prof. D.G.C Robertson is the best suited program, and therefore, the author has applied it to the various steelmaking reactions, a few examples of which are discussed. Hot metal dephosphorization occurs under non-equilibrium conditions as it takes place between the slag, which has a high oxygen potential, and the hot metal, which has a low oxygen potential. A process simulation model based on the coupled reaction model was constructed. This model considers the solid and liquid slag, liquid metal phases, and the reaction between the solid and liquid slag, besides the reaction between the liquid slag and liquid metal. Using this model, the ruling factor to increase the reaction efficiency of dephosphorization has been verified. In the secondary refining process, the values of inclusion composition calculated by the thermodynamic model, under the assumption of equilibrium with the metal composition, were found to be different from those observed in practice. A kinetic model, incorporating the reactions between slag, metal, inclusion, and refractory has been postulated, and the composition change of inclusion during treatment has been analyzed.

Jan 1, 2014

By R. M. Westcott

A two-electrode, direct current, slag resistance furnace (SRF) has been constructed and operated to selectively reduce the zinc and lead contents of non-ferrous slags. The experimental SRF is equipped with multiple methods of gas/solids injection for both mixing and reaction. A computer is used to position the electrodes and for data acquisition. A geometric factor correlation was previously developed at Columbia University for calculating the electrical resistance on the basis of furnace geometry and slag conductivity. The experimental SRF was used to test this correlation.

Jan 1, 1994

By Dexter G. Mendoza

To analyze the behavior of minor elements in the copper smelting process, the phase relations and the activities of arsenic and antimony in the miscibility gap of Cu-Fe-S-X (X = As or Sb) system have been determined at 1473K by the quenching method and the double Knudsen cell- mass spectrometric method, respectively. The experiments have been conducted for the charges in the miscibility gap with different mass%Fe/mass%Cu ratios with varying arsenic or antimony content. The activity measurements indicate that the arsenic activities in both the metal and matte phases show extremely negative deviation from the ideal behavior. The Raoultian activity coefficients at infinite dilution in the metal and matte phases are found to be almost constant against the charges in the miscibility gap, and they are 4.3 x 10-3 and 5.5 x 10-2 for the metal and matte phases, respectively. Moreover, the activity measurements of antimony show an activity value larger than that of arsenic but it still deviates negatively from Raoult's law. The activity coefficients of antimony at infinite dilution are found to be 1.2 x and 2.2 x 10-1 for the metal and matte phases, respectively. The vapor pressures of the predominant As, AS2, AsS, Sb, Sb2, and SbS species in the gas phases of arsenic and antimony, respectively, equilibrated with the immiscible solutions have been calculated on the basis of the determined activity coefficients and they are very small at less than 1 Pa, even when their contents in the metal phase are increased up to 10 mass%.

Jan 1, 2002

By Huanmei Yuan, Yuanyuan Wang, Hao Bai

Composite phase change materials are widely used in energy-saving and energy efficient process. Nano-encapsulated phase change materials are especially significant for making advanced working fluid applicable to waste heat recovery or storage. In this study, silica-coated stearic acid (SA) Nano composite phase change materials were prepared from tetraethyl orthosilicate (TEOS) and stearic acid (SA) via sol-gel process. The materials were investigated by Field emission scanning electron microscopy (FE-SEM), Transmission electron microscope (TEM), Fourier transform infrared spectroscopy(FT-IR) and Differential scanning calorimeter (DSC).The FE-SEM and TEM results show that monodisperse microspheres with stable core– shell structure were formed and SA was encapsulated in the silicon dioxide shell. The FT-IR results show that there were no chemical reaction between silicon dioxide and SA, which is the chemical property of the composite material, is stable. The DSC results show that the composite phase change material has favorable heat capacity.

Jan 1, 2016

By Linfeng Zhou, Rong Sun, Guanghui Li, Zhiwei Peng, Tao Jiang

Dust, or airborne particulate matter, from metal smelting can be either mechanically or thermally generated and it negatively affects the indoor air quality as well as the fugitive emissions from the plant. The thermally generated dust is often referred to as fume and it is typically generated whenever liquid metal comes into contact with air. For practical reasons, such as vehicle access, etc. it is often difficult to collect 100% of the fume. It is therefore highly desirable to develop processes and optimize operational procedures so that fuming can be kept to a minimum. In this series of experiments, the mechanism of active oxidation and fume formation from liquid silicomanganese under an impinging air jet in the temperature range 1400-1600°C has been explored. Characteristic properties of the fume have been established; particle diameter, shape, size distribution, and elemental composition are reported. The oxidation process is described in terms of vaporization, oxidation and agglomeration. In the boundary layer, two competing mechanisms seem to be operative in parallel: a direct oxidation of Mn vapor, and a two-step oxidation of silicon. The thermodynamic and kinetic conditions governing the two mechanisms are discussed.

Jan 1, 2016

By Adele Garkida

Compacts of crushed waste window glass, fluorescent tubes, drinking glasses and laboratory glass wares were made at various proportions from 106 microns and minus 75 microns powders in combination with 5% bentonite as binder for each glass type, after several trials to determine compatibility of particle sizes. They were made using the uniaxial press at 10,000 psi and sintered at a temperature range of 700- 750oC. The results showed anisotropic shrinkage behavior for all the samples, exhibiting an axial shrinkage lower than the radial shrinkage. Sintered compact from waste drinking glass which comprised of 60% 106 microns and 40% minus 75 microns powders showed the least sintering shrinkage factor of 1.125, fused at 700oC and the highest shrinkage factor of 1.286 obtained at 750oC. This shrinkage behaviour connotes that sintering can be employed to utilize these waste glasses up to the maximum of 95% recycled glass content in ceramic tile production.

Jan 1, 2008

By Wilson Acchar, Fernando Barcelos, Luis Carlos Pereira

"Porous ceramics have been extensively investigated as structural materials for flow of fluids in many applications, such as filters for molten metals, water purification and hot gases, thermal protection systems and heat exchangers. This class of material must have two special features: high permeability and mechanical strength. However, these parameters are influenced in different ways by the processing method and the consequent cellular structure. In this work two different types of commercial ceramic filter materials are investigated. Characterization included the evaluation of the strength values as well as the permeability behavior and microstructural analyzes of the surface fracture. The results indicate that the strength values are strong dependent on the filament defects.IntroductionCeramic materials with a cellular structure have been extensively investigated as structural materials for flow of fluids applications [1-3]. Microstructural aspects such as morphology, size of the cell and the degree of interconnectedness are mainly parameters that influence the properties of these porous materials [4-6]. The most used industrial process to produce cellular ceramics for filter application is the polymeric sponge replication method. This technique consists in dipping the polymer foam into slurry containing an appropriate binder and the necessary ceramic materials, followed by a heating treatment [2,5].Mechanical properties of cellular ceramics depend basically on cell size, degree of interconnectedness and density [1,2,5,8,9]. Materials used as filters required a good strength and also permeability values. These properties are inversely proportional to each other. Higher porosity increases permeability values but decreases the strength values [1,2,5]. The objective of this work is to study the strength resistance of a commercial porous ceramic material (10, 20 and 30 ppi) based on silicon carbide."

Jan 1, 2012

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By W. Kasprzak

Press-fit systems are widely used to seal oil lines in the automotive engine components. In the case studied a ball plug made from the 7075 A1 alloy was inserted into a 319 Al alloy cast component. The oil lines were subjected to the required component service pressure. This paper addresses the analysis of the ball plug/casting hole press-fit performance. The tools used to investigate the plug system included: the SEMIEDS technique for the assessment of the plug and the casting hole wall surface integrity; image analysis methods for the characterization of the ball plug/casting hole interface; matrix microhardness measurements of the plug and casting components; laboratory ball plug insertion, speed and force correlation; as well as the ball shearing mechanism analysis. Laboratory tests indicated that optimization of the aluminum matrix hardness in the 319 A1 alloy cast components resulted in considerable improvement of the press-fit system sealing properties.

Jan 1, 2002

By María Cristina Ruiz

Hematite precipitation is a convenient alternative for the removal of iron from leaching circuits because of its chemical stability, high density and high iron content. The precipitation of hematite from ferrous sulfate solutions was studied in a batch reactor. The precipitation occurs by two sequential steps: oxidation of the ferrous to ferric ions followed by hydrolysis of the ferric to hematite. The main objective of this study was to determine the effect of the main operating variables on the rate of two steps of hematite precipitation. The variables studied included: stirring speed (100 to 600 rpm), temperature (160 to 200 ºC), concentration of sulfuric acid (1 to 10 g/L), initial iron concentration (1 to 15 g/L), and partial pressure of oxygen (1 to 6 atm). The sulfur content and the particle size of the solids that precipitated under various conditions were also determined. The results showed that at low temperature and high acid concentration the rate of Fe3+ hydrolysis is the step that controls the overall process. The variable that affects most the rate of Fe2+ to Fe3+ oxidation and the rate of hematite precipitation is the temperature.

Jan 1, 2008

By D. D. L. Chung

"In-situ network composites are composites in which the filler network is formed during composite fabrication, in contrast to ex-situ networks which are formed prior to composite fabrication. A homogeneous in-situ network composite has the entire network at the same composition; a heterogeneous in-situ network composite has different parts of the network at different compositions. The homogeneous network composite is made either by the Method of Molten Filler Flow or the Method of Dissolution and Deposition; a heterogeneous network composite is made by the Method of Liquid-Phase Networking. Examples include polymermatrix and metal-matrix composites.IntroductionNetwork composites refer to composites containing a continuous three-dimensional network as the filler. These composites are attractive in their lack of delamination failure, which is usually characterised by two-dimensional composites. The filler and matrix in a network composite can be considered two interpenetrating networks. The mechanical interlocking of the networks adds to the cohesion of the composite. In cases where the filer is much better than the matrix in a certain property, the network nature of the filler makes the filler highly effective in improving that property in the composite in all directions. The property desired in the composite may be high strength, high modulus, low coefficient of thermal expansion, high thermal conductivity, or low electrical resistivity."

Jan 1, 1994

By Cecil Harriss

Philip Environmental Services Corporation's (Philip's) innovative fluidized bed thermal desorption system recovers mercury from contaminated soil. Referred to as the Thermal Recycling System, Philip has constructed a mobile thermal desorption system that has a processing rate up to five tons per hour. The system includes a continuous-feed system, all radiant heat, inert gas atmosphere, hot gas filter, two-stage cooling, and a water treatment system. Based on treatability studies, the processed soil can meet cleanup objectives as low as two milligrams per kilogram and passes the mercury toxicity characteristic leaching procedure test.

Jan 1, 1996

By Tomás Vargas

The catalytic influence of a pure strain of Thiobacillus ferrooxidans (ATCC 19859) on the dissolution of natural pyrite crystals was studied using electrochemical techniques. The results showed that this microorganism catalyze the leaching of pyrite by both, oxidizing ferrous iron in solution and depolarizing the reduction of ferric ion on this sulfide. In addition, studies of bacterial corrosion under applied potential showed that pitting on the pyrite surface centers on weak sites of the sulfide structure in which bacteria has attached, but occurs only when the ferric iron in solution induces an adequate level of anodic polarization on the mineral.

Jan 1, 1992

By J. Sofra

The quantity of copper produced by secondary material processing is increasing as metal producers look to cleaner and cheaper sources of copper. The need to smelt secondary copper more economically, to process a wide range of materials with large fluctuations in size and composition and to cope with the increasingly stringent environmental constraints have put considerable pressure on existing conventional secondary copper smelters. The Top Submerged Lance process, developed and commercialized by Ausmelt Ltd offers a low cost technology, which is particularly adapt at processing copper-bearing scrap and residues. The application of Ausmelt Technology to replace conventional secondary copper processing operations introduces potential for significant advantages in environmental performance, and improved process efficiencies through the use of cheaper hels and reductants, the high rate of metal recovery and the flexibility inherent in the technology to process various feed material types. The economical, process and environmental benefits of its application are highlighted for both the smelting and converting stages of copper production.

Jan 1, 1997