Search Documents

By David A. Zegeer

Since 1980, more than 40 miners have lost their lives by being trapped and suffocating in stock-piles, bins, silos, and similar facilities. Mine Safety and Health Administration (MSHA) is concerned about these accidents, most of which could be prevented if management and miners appreciated the hazard. In February 1986, the coal industry had a suffocation accident that drew national attention. A group of engineers were standing on a coal stockpile. It gave way under their feet. Five of the engineers were buried in the coal and suffocated. As with all fatal accidents, MSHA investigated the cause of this tragedy. I also asked my staff to look into the history of similar accidents. I found out it is rare to have multiple fatalities due to suffocation in material. But, over the years, there has been a long series of individual fatalities from this type of accident. Here are some examples. In Oct. 1985, a coal mine employee in Virginia entered a hopper to collect a coal sample. The feeders were started while he was standing in the hopper. He sank into the coal and suffocated. In Sept. 1985, an employee at a Texas sand company climbed onto a surge pile, to check a problem with sand flow. When other employees found him, the sand had swallowed him. Only his face and one hand were showing. Though the victim's face was clear of the sand, he suffocated before rescuers could free him. Many people do not realize you can suffocate in this kind of situation, though your head is free. Every time you exhale, the material has room to shift and press harder against your chest. Then you have less room to inhale. If this goes on long enough, it gets to the point where you cannot inhale at all. That is what happened to the victim in this accident. In May 1985, a plant operator at a Wisconsin sand and gravel operation purposely slid into the drawhole of a surge pile. He tried to break up large rocks that were clogging the drawpoint. Material piled on the side of the surge pile slid down and buried him. The operator was wearing a safety belt and line. But he was covered by 3 to 3.7 m (10 to 12 ft) of material and could not be pulled free. This incident illustrates another point. A safety line can help. But it is not enough. Workers should never put themselves in a position where loose material can fall on them from above. In Jan. 1985, a young Utah coal miner was waiting for a ride home from a co-worker whose job was at the tipple. A jam developed in the coal bin. The men could not clear the jam from the outside. So the young miner jumped into the bin. He started digging with a shovel at the toe of the coal pile. It caved in on him and he suffocated. The young miner had only three months of mining experience. He had not been trained for work around the coal bin. Since 1980, 16 coal miners and 26 nonmetal miners have lost their lives in loose-material suffocation accidents. Suffocation accidents occur in many areas around mines - bins, hoppers, stockpiles, surge piles, and silos, among others. One recent accident occurred at a surface coal mine in Illinois. The victim was walking over an area that had been drilled and blasted the week before. He fell into a void that had been crusted over with earth. He too suffocated. And many materials have been involved in suffocation accidentscoal, crushed stone, sand, salt, different kinds of ore, ammonium nitrate pellets used in blasting, and a powdery byproduct of iron ore milling called calcine. In addition to fatal accidents, there are near misses. We do not know how many. Most of them are not reported. A person who gets trapped in material, but is rescued, is usually unhurt. MSHA sometimes hears about these accidents by chance, or because they are reported in the local media. We do know that near misses are happening far more often

Jan 1, 1987

By Thomas B. Dellinger

Since 1950, rotary-drilled, large-diameter holes, "big holes", with depths to over 300 feet and diameters of over 30 inches have become numerous and widespread. Fifty such holes have been drilled for access shafts to LPG mined caverns, Over 70 holes have been drilled for various other commercial activities. Over 150 holes have been drilled by the AEC for atomic testing purposes. These holes have ranged up to 300-inch diameters with 1600-foot depths, 120-inch diameters with 570-foot depths, and 72-inch diameters with 4800-foot depths. Equipment is now available to drill a wide range of ?big holes? for varied requirements. At least a dozen drilling contractors are participating or have participated in the drilling of "big holes". The accompanying tables show pertinent historical, technical and economic data on over 250 holes. The illustrations to be presented concurrently with this paper show the various equipment and accessories now in use. (See Appendix I for captions of illustrations.)

Jan 1, 1966

Semisoluble salt minerals are characterized by their ionic bonding and are distinguished from soluble salt minerals by their limited solubility in water. One group of semisoluble salt minerals being considered is the alkaline earth salt minerals, including fluorite (CaF2), calcite (CaCO3) and apatite (Ca5F (PO4)3), as well as celestite (SrSO4) and barite (BaSO4). Another group of semisoluble salt minerals being considered is the rare-earth salts, which include bastnaesite ((Ce, La) CO3F), monazite (CePO4) and xenotime (YPO4). Surface chemistry features of these selected semisoluble salt minerals are discussed with respect to flotation separations. First, the surface chemistry features of alkaline earth semisoluble salt minerals are reviewed, and then the surface chemistry features of rare-earth semisoluble salt minerals are examined. The discussion includes electrokinetic behavior, wetting characteristics and collector adsorption.

By Margreth Tadie, Chalwe Chibwe

Physicochemical properties of copper electrolytes are a strong fundamental consideration in electrodeposition processes during electro-purification and recovery of copper. Their influence extends to mass transfer as well as energy consumption during the electrodeposition process. In this study, the influence of electrolyte composition on electrolyte physicochemical properties was investigated to review the existing literature data. This review of data is considered necessary as more and more electrowinning models are being developed for process prediction and optimisation and a need of such data is required for accurate prediction of physicochemical properties. The major components of importance to the formation of smooth high-quality and high-purity copper cathodes at optimum current efficiency are considered the species in solution. These include Cu ions, Fe ions (major impurity), H2SO4, and a smoothing agent additive. A 5-factor, 2- and 3-level experimental design was employed to determine the effect of copper (35 and 45 g/l), sulphuric acid (160 and 180 g/l), iron (1, 3, and 6 g/l), polyacrylamide additive (2, 5, and 10 mg/ l), and temperature (45 and 55 °C) on electrolyte density, conductivity, and the diffusion coefficient in synthetic copper electrowinning electrolytes. The major species in a copper electrowinning electrolyte are found to be the most relevant for prediction of physicochemical properties. These results indicate that relatively simple empirical models are sufficient for modelling of the electrolyte domain in electrowinning, without the need for the generation of vast amounts of complex experimental data.

Feb 1, 2021

By B. K. Cantrell

The U.S. Bureau of Mines and others have conducted a number of occupational exposure surveys since the publication of the International Agency for Research on Cancer report of 1989, which labeled diesel exhaust as a probable human carcinogen. These surveys have assessed diesel exhaust exposure using measurement of diesel aerosol and/or specific polycyclic aromatic hydrocarbons as indicators of exposure. This paper reviews present diesel emission standards, available diesel exhaust aerosol measurement techniques, and the results of the occupational exposure surveys. In the surveys, diesel aerosol was emphasized because it is a major component of diesel exhaust, is suspected to contribute to the health hazard, and is readily measurable. Three primary aerosol measurement techniques were used: respirable combustible dust, size-selective sampling, and measurement of the elemental carbon fraction. Occupations surveyed included mine workers, railroad workers, forklift operators, fire fighters and truck drivers. The studies found mean diesel aerosol concentration levels in the range of 0.004 to 1.74 mg/m3? Highest aerosol exposures were in confined spaces such as mines where heavy diesel equipment is used. Polycyclic aromatic hydrocarbons typically are found at very low concentration levels and are not unique to diesel exhaust.

Jan 1, 1996

By J. R. Patts, A. B. Cecala

"After industrial sand has been mined and processed, the finished product is typically loaded into small bags of 45 kg (100 lb) or less, large bulk bags of 454 to 1,361 kg (1,000 to 3,000 lb), or vehicles such as trucks or trains for transport to end users. As the sand is being transferred and loaded, dust can be released into the work environment, potentially exposing workers to respirable crystalline silica. A number of control technologies have been developed and utilized in an effort to reduce dust liberation during loading operations. For bulk loading into trucks or trains, the U.S. National Institute for Occupational Safety and Health (NIOSH) evaluated one of these technologies, the Dust Suppression Hopper (DSH), at two industrial sand processing plants. Results from these case studies show that the DSH reduced airborne respirable dust levels by 39 to 88 percent, depending upon the product size being loaded.IntroductionInhalation of respirable crystalline silica dust can lead to the development of silicosis, a disabling and potentially fatal lung disease. Once contracted, there is no cure for silicosis, so the goal is to prevent the development of the disease by limiting exposure to respirable dust containing crystalline silica at or below the exposure limit of 50 µg/ m3 recommended by the U.S. National Institute for Occupational Safety and Health (NIOSH, 2002). At industrial silica sand operations, the product contains high levels of crystalline silica, so effective control technologies are needed to minimize the respirable dust exposure of workers.NIOSH, in partnership with the Industrial Minerals Association–North America, published a dust control handbook (NIOSH, 2012) focused upon control technologies for industrial- mineral mining and processing operations. One chapter in this handbook discussed technologies for controlling dust liberated during bulk loading, including telescoping loading spouts, dust collection systems for loading spouts, enclosures for load-out areas and a newer technology known as Dust Suppression Hopper (DSH)."

Jan 9, 2018

By B. Birol, M. N. Saridede

"Slag density is a significant factor in determining the process efficiency of the electroslag remelting (ESR) process, where calcium fluoride (CaF2)-based slag is formed synthetically to refine metal ingots. Although there are some former studies investigating the density of CaF2-containing slags, the prediction models focusing on them are applicable only to some specific systems. The present study aims to build a model to predict density for a wide range of CaF2-containing ESR slags. To investigate density for various slag compositions, CaF2-Al2O3-based and CaF2-Al2O3-CaO-based slag compositions were prepared. Additionally, some minor constituents like FeO, MgO and MnO were added to a 5:3:2 CaF2-Al2O3-CaO slag in order to investigate the effects of these constituents on the slag. The volumes of the prepared slags were measured in a tube furnace at 1450-1550 °C using the sessile drop technique, and their densities were calculated. The results showed that for the slags, density is related to optical basicity, and therefore a prediction model based on an Arrhenius equation was built. The model was tested with data from literature, and its limitations and validity are discussed.IntroductionThe electroslag remelting (ESR) process is a refining method in which a metal ingot is remelted under a synthetic slag. These synthetic ESR slags are mainly composed of calcium fluoride (CaF2), calcium oxide (CaO) and aluminum oxide (Al2O3). Other constituents like iron oxide (FeO), magnesium oxide (MgO), manganese oxide (MnO) and chromium oxide (Cr2O3) are added to this system in relatively low amounts, according to the type of steel ingot to be refined. The prediction of slag properties, such as electrical conductivity, viscosity and density, is crucial for the selection of the synthetic slag in order to obtain the required process parameters, like temperature, the passing time of the molten metal droplet through the slag, and metal-slag separation (Akbari, Reitz and Friedrich, 2009; Hara and Ogino, 1981; Mattar, El-Faramawy and Fathy, 2002; Mehrabi, Rahimipour and Shokuhfar, 2005; Presoly, Korp and Schneider, 2008).As slag density affects metal-slag separation in the ESR process, predicting the density of an ESR slag is important for appropriate refining and improved product quality. Although there are many studies investigating the density of slags (Akbari, Reitz and Friedrich, 2009; Aune, Hayashi and Sridhar, 2005; Hara and Ogino, 1981; Matsushita, 2011; Mills and Keene, 1987, 1981; Seetharaman et al., 2013; Shu, 2007; Shu and Chou, 2013; Sikora and Zielinski, 1974; Xu et al., 2012; Zhang and Chou, 2010), the prediction models built are generally valid for oxide-containing slags (Aune, Hayashi and Sridhar, 2005; Bottinga and Weill, 1970; Mills and Keene, 1987; Seetharaman et al., 2013; Shu, 2007; Xu et al., 2012; Zhang and Chou, 2010). These models were built on either the molar volumes of the constituents (Bottinga and Weill, 1970; Mills and Keene, 1987) or the thermodynamically calculated enthalpy or free energy of mixing, which can be applied to a system containing constituents sharing an ion, such as an O- ion for oxide systems (Aune, Hayashi and Sridhar, 2005; Hillert, 1980; Persson et al., 2007). Some recent studies modeled the density of some oxide slags on their optical basicity (Shu, 2007; Shu and Chou, 2013; Xu et al., 2012; Zhang and Chou, 2010)."

Jan 1, 2016

By Nicolin Govender, Pramod Kumar, Raj Rajamani

Mill power models have been used in a variety of ways in industrial practice since power directly equates to throughput and fineness of ground product. We first start with Hogg-Fuerstenau Power Model and show how this model successfully predicted the power draw of many grinding mills in several mining operations. Then, we show how this model was on the verge of being able to predict the influence of lifter design on power draw. Next, we describe the discrete element model and how it overcame the issues faced by the previous power model. Using a DEM software known as Millsoft, we show the influence of lifter design geometry on power draw and analyze the power draw of rubber lifters versus the steel lifters via several case studies. As years passed, the two-dimensional discrete element model imbedded in Millsoft is superseded by three-dimensional discrete element method. Due to the gigantic computational power of graphic processing units, new computational codes that can do the tumbling motion along the entire length of the mill has come about. Here, we show the predictive capability of Blaze-DEM for ball and SAG mills.

By Yongheng Jiang, Wentong Wang, Haoming Luo, Chuanju Liu, Qianjun Zhang, Sha Guo

Rock burst has always been a major problem in deep underground engineering with high stress, and rock burst strength evaluation has become an important research topic. To effectively predict the rock burst hazard in underground rock mass engineering, a cloud model (CM) rock burst intensity evaluation method based on the CRITIC method and order relation analysis method (G1) was proposed in this paper. First, a rock’s uniaxial compressive strength σc, tangential stress σθ, uniaxial tensile strength σt, ratio of uniaxial compressive strength to tensile strength σc/σt (brittleness coefficient), ratio of tangential stress to uniaxial compressive strength σθ/σc (stress coefficient), elastic deformation energy index Wet, and depth of cover H were selected as evaluation indices of rock burst intensity. Ninety-five groups of rock burst measured data at home and abroad were selected, and the objective weight and subjective weight of each index were calculated by using the CRITIC method and G1 method, respectively. The comprehensive weight was determined according to the combined weighting method of game theory, and the sensitivity of each evaluation index was analyzed. By utilizing a forward cloud generator, the membership degrees of different rock burst grades were calculated, and then the rock burst intensity grades of the samples were evaluated and compared with the evaluation results of the CRITIC-CM method and G1-CM method and the actual grades. Finally, the rock burst classification ability of the model was analyzed. To better verify the accuracy and reliability of this model, the rock burst case of the W39 line in the Chengchao Iron Mine was analyzed by using this model. The research results show that the rock burst evaluation results based on CRITIC-G1-CM are basically consistent with the actual rock burst grade, and the rock burst intensity grade evaluation model has good practicability and reliability.

Sep 1, 2023

By K. S. Radcliffe

Results are presented for the first phase of an experimental program to study the feasibility of using acoustic velocity for predicting the state of stress in a rock mass. Compressional wave velocities were determined axially in cylindrical samples during uniaxial compression for several rock types conditioned in dry and water-saturated environments. Results indicate that in rocks containing compressible voids or cracks, substantial velocity change occurs with the application of stress in the lower (below 100 MPa) stress regime. The effect norm- ally is nonlinear, however, and diminishes to asymptotic values when cracks or voids become closed or with saturation. Empirical prediction equations were derived for each rock type by linear and nonlinear regression analyses, and correlation coefficients were calculated to determine the equations that best fit the stress- velocity data. The operational range for predicting stress using compressional-wave velocity appears to be within the range of vertical stress expected in most shallow to intermediate depth mining operations (less than 1,000 m). Based on the experimental results to date and theoretical considerations, it appears that the technology can be advanced to predict in situ stress based on acoustic P-wave velocity determinations in most mining situations.

Jan 1, 1986

By P. Eger, D. Green

"The Soudan Mine was Minnesota’s first iron mine, operating from 1882 to 1962. The mine was donated to the State of Minnesota in 1963 and became a state park in 1965. The mine discharge contains elevated copper and cobalt concentrations and has been treated with an ion-exchange-resin-based system since 2009. The system includes flow equalization tanks, bag and cartridge filters, a carbon tank and two commercial ion exchange tanks. Although effective, the system’s high cost, inefficient removal of suspended material and substantial maintenance have been ongoing and troublesome issues.In November 2012, we initiated a pilot test using a peat-based sorption media. This media is produced from raw reed-sedge peat through a patented, low-temperature carbonization process that produces a hardened granular sorption material. The granules are uniform, have high hydraulic conductivity and maintain the high metal affinity of natural peat.Mine water was pumped through the peat-based sorption media without any pretreatment. Copper input concentrations typically ranged from 30 to 60 µg/L but increased to a high of 364 µg/L in the summer of 2013. Since startup, more than 60 million L (16 million gal or 32,000 bed volumes) have been treated, with average removal rates of 75 percent for particulate copper and 60 percent for dissolved copper. Backwash is required at about 4,000 bed volumes, but with a combination of air sparging and high-flow backwash, the suspended material is removedfrom the media.One tank of the peat-based sorption media was found to remove copper similarly to the first four components of the existing system. By reducing size and complexity, reductions in operation and maintenance costs are possible. A comparison of the estimated costs indicate that replacing the four initial components with the single media tank has the potential to reduce annual operating costs by more than half from around $163,000 to $70,000."

Jan 1, 2015

By Changjiang Li, Jun Yang, Qiang Fu, Xu Chang, Xing Wu, Yubing Gao

With the development of underground mining, the deformation of roadway floor has increasingly become a major constraint on the safe and efficient production of coal mines. To address the floor deformation that was caused by massive stress concentration in roadway, an innovative method based on deep-hole directional tensile blasting technology is put forward. By taking No.122108 working face in Caojiatan Coal Mine as engineering background and analyzing the mechanism of deformation, a numerical simulation and field test are carried out to verify the effect on deformation control of this technology. It is found that the deep-hole directional tensile blasting technology can actively control the fracture position of the roof in the gob area and cut off the stress transmission path, so as to relieve the stress in the roadway. And since different blasting parameters have different impacts on the stress relief effect, a numerical simulation is implemented and it is found that the stress relief effect is the best when blasting depth is set to be 32 m and the blasting angle be 60°. By applying the optimal blasting parameters to the field engineering test, it can be seen that the deep-hole directional tensile blasting technology could effectively reduce maximum stress value and stress field range of the both sides of the roadway, and make the stress field far away from the roadway, thus effectively controlling the deformation of the roadway floor. The deep-hole directional tensile blasting technology can effectively solve the problem of roadway floor deformation and can be safely applied to engineering sites.

Jun 13, 2023

By Ali Nazem, Rennie Kaunda, Zoheir Khademian, Fei Wang, Raymond Henn, Alex Peretiatkol

"The field demonstration portion of the Underground Grouting and Ground Improvement (UG&GI) short course offered by the Colorado School of Mines was held on May 18, 2016 at Baski Inc.’s Yard in Denver, CO.Numerous full field scale demonstrations of grouting methods and equipment were conducted under various field conditions. As part of these field tests, permeation grouting testing and demonstrations were also conducted. Various cement grout mixes were injected into 1.5-m (60-in.) tall transparent sand columns under controlled conditions (Fig. 1). The objective of the sand column permeation grouting demonstrations in the study was to show students the effects of ordinary Portland cement versus ultrafine cement on the engineering properties of the grout, and the permeation height through various types of soil stratigraphic layers in the sand columns. Similar previous demonstrations have had a specific focus on various brands of Type I-II Portland cements and ultrafine cements with a range of water cement ratios and injection pressures. More detailed information about these previous studies can be found in published proceedings (e.g. Henn et al., 2009 -2011).Equipment and material usedThe five clear plastic sand columns were 191 mm (7.5 in.) inside diameter and 1,524 mm (60 in.) tall. Each sand column had a 19 mm (0.75 in.) diameter hole drilled at the base (bottom) of the blind flange for injection of the grout. A perforated plate and/or screen at the base of the sand columns helped to prevent sand from plugging injection port. A ChemGrout grout plant was used for the demonstration consisting of 0.36 m3 (97 gal) high shear (colloidal) tank mixer, a 0.36 m3 (97 gal) agitator tank and a progressive helical cavity pump with maximum output capacity of 77 L/min (20 gpm) at a maximum discharge pressure of 265 psi (18 bar) (Fig. 2). A simple grout header arrangement consisting of control valves, pressure gauges, flow meter, grout delivery and return line, and a short injection line was also custom built. Also used were infra-red thermometers to measure the temperatures of the grout mix batches, CRD and marsh funnels to measure viscosity, baroid mud balance to measure specific gravity, and a digital scale to measure weights. The grout materials used were Holkim Portand cement (Type I-II), Nippon Steel Sumikin superfine cement and U.S. grout ultrafine cement."

Mar 1, 2017

By P. B. Queneau

An operating problem encountered at the Moa Bay operation in Cuba, where nickeliferous laterite ore is processed by sulfuric acid pressure leaching, is the formation of alunite and hematite deposits on the autoclave walls. The AMPX Extractive Research & Development, Inc., metallurgical laboratory (Golden, Colorado) has made substantial improvements in the Moa Bay process in the areas of metal recovery, energy consumption, and feed versatility. One of the advantages of AMAX's process is its ability to treat substantial portions of nickel- and magnesium-rich serpentine while maintaining acid utilization efficiency. The process minimizes scale formation by combining staged acid addition with vigorous agitation and 270°C operation, but does not eliminate scaling. This paper describes how advantage can be taken of MgSO4?XH20 precipitation both to inhibit alunite scaling and to disperse hematite scale within the MgSO4?XH20 matrix. Cooling the autoclave from its 270°C operating temperature down to 180°C takes advantage of the reverse solubility of magnesium sulfate. The magnesium dissolves, liberating entrained hematite, thus providing a means for control of autoclave scale with minimum process disruption.

Jan 1, 1984

By S. W. Cavender

The analysis of the results of metallurgical experiments is often complicated by experimental errors and uncertainty, the complexity of the system being studied, and the confusion of correlation with causation. Consequently, comparative statistics are used to determine if a difference exists between the outcomes of tests, an estimate of this difference, and the precision of the estimate. This paper reviews the use of significance tests and confidence intervals for the comparison of results from two tests, the use of reference distributions, and blocking and randomization techniques to reduce unavoidable sources of variability. These techniques are demonstrated using plant and laboratory data.

Jan 1, 1993

By Yuchen Wu, Purushotham Thkkaraja, Marek Borowski, Jie Liu, Jianwei Cheng, WANCHENG ZHENG, Yu Wang, Weidong Lu, Gang Zhao, Zhanyou Sa, Huan Yang, Yuhang Wu, Hui Wang

The abstract discusses the importance of gas drainage in coal mines for safety, environmental protection, and resource utilization. It highlights the significance of borehole sealing technology for efficient gas drainage. The study introduces a new inorganic retarding sealing material and investigates its properties, including stability, thermal stability, fluidity, and thixotropy. The material's diffusion performance in cracks is tested using a self-designed system. Field tests in a coal mine demonstrate the material's effectiveness in improving borehole sealing compared to traditional materials.

May 1, 2022

By Louis A. Panek

Using an approach based on the theory of similitude, the author develops a general equation and related concepts that provide new insights to an old problem. The load-bearing capacity (strength) of a square, rectangular, or cylindrical prism of a brittle material such as rock, coal, or concrete is expressed as the mathematical product of a size effect, a shape effect, and a function of the mechanical properties (deformability, cleat/joint spacing, and friction) of the pillar, roof and floor materials. Through an application of multivariate statistical analysis, the results of assorted tests and observations of failed pillars can be combined into a fundamental scaling equation, which provides a unified, consistent approach to the estimation of mine pillar strength. The form of the equation is sufficiently general to be able to incorporate refinements in the characterization of the basis factors, as they become available through future experimentation and analysis.

Jan 1, 1979

By Brian F. Taylor

The Mexican fluorspar industry is faced with and will face serious problems, some of their own making and others beyond their control. However, they still offer the most secure source of fluorspar for North American' consumers. Since 1975, even in light of declining markets, they have, increased then production capabilities' as shown in Table #1. In analyzing Table #1, we note that Compania Miners Rio Colorado has closed down due to their ore reserves being exhausted. Fluorita de Rio Verde expanded their acid grade fluorspar capacity in anticipation of additional North American business. Campania Miners Las Cuevas presumably increased capacity to meet their North American contractual commitments and to supply their own hydrofluoric acid plant (Fluorex) at Juarez, Mexico. Historically, the Mexican fluorspar industry has relied on the United States as the mainstay for their sales. As shown in Tables #2 and #3, the Mexican share of the United States market has moderately decreased. However, as noted in Table #4 the volume loss is substantial as explained below.

Jan 1, 1985

By F. D. Fox

Abandoned mill tailings deposits can be found scattered throughout the Northern Black Hills of South Dakota, indicative of past mining activities that originated during the great gold [ERRATA SHEET RESTORATION OF GOLD MILL TAILINGS, BLACK HILL, SOUTH DAKOTA 84-119 F. D. Fox Under subtitle Prospects Related to Present and Future Tailings Disposal Practices, include reference No. 12 in paragraph seven after "construction of the Grizzly Gulch tailings disposal project,"12 Reference 12 should read: Jeffries, Lawrence F. and Tczap, Andrew, "Homestake's Grizzly Gulch Tailings Disposal Project," paper presented at 1978 International Mining Show, October 11, 1978.]

Jan 1, 1984

By Michael J. Mujadin

Since the late 60's, planners at American Natural have known that natural gas supplies from traditional sources will be insufficient to maintain a consistently high level of service in the near future. This dwindling of traditional gas reserves will force American Natural and other gas companies to seek new and more exotic sources of supply. In recent years a number of alternative supply sources were considered, including arctic gas, LNG, and SNG based on naptha, LPG and coal feedstocks. Several combinations, all of which included SNG from coal were selected as the most suitable alternative sources of gas supply for American Natural, and thus our company embarked on the formation of a coal gasification project in the early 70's. Work began with the evaluation of available coal supplies in the United States in late 1970. Western North Dakota was selected for several reasons: large contiguous reserves of lignite were available near the surface, similar to German brown coal for which the Lurgi gasification process was originally developed; the conditions for land reclamation in the area are favorable; and the people in the area have a positive attitude toward well ordered development.

Jan 1, 1977