Search Documents

By B. Holen, J. R. Baregi, J. A. Organiscak, A. B. Cecala

The National Institute for Occupational Safety and Health (NIOSH) cooperated with 3M Company in the design and testing of a new environmentally controlled primary crusher operator booth at the company’s Wausau granite quarry near Wausau, WI. This quarry had an older crusher booth without a central heating, ventilation and air conditioning (HVAC) system, and without an air filtration and pressurization system. A new replacement operator booth was designed and installed by 3M based on design considerations from past NIOSH research on enclosed cab filtration systems. NIOSH conducted pre-testing of the old booth and post-testing of the new booth to assess the new filtration and pressurization system’s effectiveness in controlling airborne dusts and particulates. The booth’s dust and particulate control effectiveness is described by its protection factor, expressed as a ratio of the outside to inside concentrations measured during testing. Results indicate that the old booth provided negligible airborne respirable dust protection and low particulate protection from the outside environment. The newly installed booth provided average respirable dust protection factors from 2 to 25 over five shifts of dust sampling with occasional worker ingress and egress from the booth, allowing some unfiltered contaminants to enter the enclosure. Shorter-term particle count testing outside and inside the booth under near-steady-state conditions, with no workers entering or exiting the booth, resulted in protection factors from 35 to 127 on 0.3- to 1.0-µm respirable size particulates under various HVAC airflow operating conditions.

Jan 1, 2015

By D. C. Fuller

CoaLiquid, Inc. (CLI) has been in the coal- oil-mixture (COM) business for over five (5) years. The initial pilot processing facility was replaced by a 2000 barrel per day commercial production facility in August of 1979. For over two (2) years CLI has been expanding its efforts and conducting large scale production and combustion demonstrations successfully in many locations across the United States. To facilitate the marketing effort, CLI has recently constructed a special trailer containing all equipment needed for a temporary COM retrofit. CoaLiquid has conducted commercial scale combustion demonstrations in the following types of combustion units: kilns, calciners, industrial boilers, blast furnaces and driers.

Jan 1, 1982

By Umay Cinarli, Ahmet Turan

High-energy consumption in primary aluminum production (from bauxite ores) makes secondary aluminum production (from metallic raw materials such as scrap and dross) very critical. Aluminum dross, as a waste, arises in pyrometallurgical processes, and it is the mixture of metallic Al, Al2O3, other metal oxides, metal halides, and some other compounds like AlN. Aluminum dross has two subgroups (white and black) with respect to its metallic aluminum content. White dross is a secondary aluminum resource because of its high metallic aluminum content, whereas black dross, having low metallic aluminum content, is generally disposed in dumping areas. In the present study, it was aimed to develop a simple technique to valorize aluminum black dross in the form of alumina-based ceramic materials through pyrometallurgical (calcination) and hydrometallurgical (leaching) operations. Moreover, thermochemical simulations were conducted by using HSC Chemistry 6.12 software to simulate calcination conditions. After leaching experiments, an alumina-based ceramic containing approximately 36.8% Al2O3, 61.4% MgAl2O4 with 1.8% Na2FeO4, which might be available to use as a spinel refractory in steel smelting furnaces, was obtained in the experiment carried out in a solution containing 10 mLH2SO4 and 40 mL distilled water (3.5 M). Moreover, the sinterability of the alumina-based ceramic was investigated at the temperatures from 1350 to 1550 °C. In the sample which was sintered at 1550 °C, a density value of 3.15 g cm−3 and a hardness value of 69.58 HV were measured.

Oct 26, 2020

By C. I. Basilio

The adsorption of dialkyl di-and mono-thio-phosphinates on gold, silver and gold-silver alloys has been studied in the present work. These reagents, which are selective collectors for sulfide flotation, have been found to improve precious metals recovery from ores. Voltammetric studies have indicated that dithiophosphinate adsorbs on gold at much higher potentials than on silver, while monothiophosphinate adsorbs only on silver. However, both adsorb on gold-silver alloys with the adsorption potential decreasing with increasing silver content. Using FTIR spectroscopic measurements, the surface species formed during the interactions of these collectors have been identified. The results of the electrochemical and spectroscopic measurements have been compared with the contact angle data obtained at controlled potential conditions.

Jan 1, 1992

By Arnold P. Szaj

There is no startling revelation to the fact that the mining industry as a whole is generally moving toward the use of larger equipment to process ores in quantities far greater than what was even considered a decade ago. Trucks and shovels have led the way in extra large machines and many other manufacturers have followed suit in the development of so-called "supers" in their line of equipment. In order to keep pace with the industry, crusher manufacturers have also enlarged the size of their equipment. There is now on the market, a Gyratory crusher capable of accepting a 72" diameter piece of ore. Primary jaw crushers have also increased in size. It is inevitable, therefore, that larger secondary cone crushers would also be required to complement the other equipment used to process these large quantities of ore. This super-size secondary cone crusher is the SYMONS 10 Ft. Cone Crusher. Until 1973, the largest cone crusher built was the 7 Ft. Extra Heavy Duty crusher, which is currently used in the majority of the mining operations throughout the world. The 10 Ft. crusher, when compared to the 7 Ft. Extra Heavy Duty Crusher, is approximately 1-1/2 times larger in physical dimensions; three times heavier; will accept a maximum feed size which is approximately twice as large; and will crush at approximately 2-1/4 times the rate of the 7 Ft. machine at identical closed side settings. It will be the largest cone crusher built in the world. At the present time, Rexnord's Nordberg Machinery Group has accepted an order for two 10 Ft. Standard cone crushers to be delivered to an iron ore mine in South Africa in early 1975.

Jan 1, 1973

By X. Wang, Y. Luo

The propensity of coal spontaneous combustion can be evaluated using various laboratory testing methods, such as R70 adiabatic tests, thermal gravimetric analyzer (TGA) tests and critical self-heating temperature (CSHT) methods. Each of the methods has its unique characteristics and index for classifying the propensity of self-ignition of coals. Accountable relationships among the propensity indices of different methods should be established. Using the newly established R70 and TGA testing setups in our ventilation laboratory, samples from U.S. coal mines have been collected and tested. The TGA is a relatively new quantitative method. A test can be conducted in a relatively short time, within about one and a half hours, compared to the adiabatic tests. The temperature and weight of the sample can be measured with high precision and then used to determine the activation energy of the coal, which is a good indicator of the potential for self-heating. Under a specific experimental design, the TGA technique could perform the proximate analysis for determining coal quality parameters (e.g., moisture, volatile matter, fixed carbon and ash content). These parameters can be used in an empirical equation for assessing the potential for coal self-ignition. The trend of activation energies determined using TGA techniques is reasonably consistent with the trend of activation energies determined using adiabatic tests. As a case study, a comparative analysis of these two methods for determining activation energy was made on coal samples collected from Indiana. The kinetics of the spontaneous combustion mechanism has been explained. If the functional groups of a coal such as hydroxyl (-OH), carboxyl (-COOH), methyl (-CH3), etc., activate more easily with a small amount of activation energy at a relatively low temperature, the coal will have a higher potential for self-heating. With the kinetic and coal quality parameters determined by the TGA setup, it has been found that the coal with a low potential for self-ignition has low self-heating rate, a high activation energy and a high minimum self-heating temperature.

Jan 1, 2012

By Yucheng Li, De Huang, Yonghong Liu

Mine frictional resistance is one of the essential parameters of mine ventilation systems, and it is of considerable significance for the prevention and control of mine risks and accident hazards. Frictional resistance requires a lot of resources and time and has errors. To reduce the errors of frictional resistance, a regression model of frictional resistance is proposed based on the correlation analysis of the affecting factors. Through the comparative test analysis of seven regression methods, it is found that the classification and regression tree method for solving the proposed regression model has better performance than other methods. The least square error criterion is used to calculate and rank the importance of the factors affecting frictional resistance. The results show that the cross-sectional area of the tunnel, the support method, and the presence or absence of devices or pedestrian ladders have the most considerable influence on the prediction accuracy of frictional resistance. The support methods and cross-sectional areas are essential input variables. Through the combination test analysis of the influencing factors, the results show that the regression model does not have predictive ability when the number of input variables is less than 3 and the best predictive performance cannot be obtained using all the influencing factors. The best prediction model of resistance is to combine the shape of the tunnel, the support method, the presence or absence of devices or pedestrian ladders, and the cross-sectional area. The method proposed in this paper does not require a lot of resources and time investment, and the frictional resistance error is small. At the same time, it solves the problem of resistance prediction with incomplete data of influencing factors and provides a compelling new method for obtaining frictional resistance parameters.

Jan 28, 2022

By J. Peterson, P. G. McKneight, R. W. Riggle

"In today’s tough mining environment, the key difference between surviving and thriving is how effectively miners optimize their mining operations. This paper explores the compounding effects material fragmentation has on mining costs and productivity. Starting with Drilling & Blasting and moving through Loading, Hauling and Crushing, we will illustrate the opportunities to improve operating costs and thus reduce the Total Cost of Ownership (TCO) of the total mining system. Material size and volume requirements are defined by the needs of the mill or plant, and drive the rest of the mining operation from the bench through the primary crusher. At the start of the cycle, where the rock mass is drilled and blasted, the degree of fragmentation and the muck pile configuration is determined, as are the effects on cost and productivity of all subsequent operations. The cost of managing oversize material, including secondary handling, overloading, reduced diggability, higher load factors, extra pass loading, increased wear factors and reduced throughput rates are all opportunities for improvement. INTRODUCTION Having visited many mine sites, customers are asking about the end to end mining value stream from loading to the crusher and how to measure the cumulative effects on each part of the mining value chain. All too often improvements with the drilling and blasting may impact fragmentation but do not improve the diggability so the net change on cycle times or fill ratios is perceived to be negative at the point of loading but they may have a measured improvement going through the primary crusher. This makes it imperative to measure performance at each segment of the overall cycle and not just to the crusher but thru it. The mine material process originates with solid rock, in-situ, and progresses to the output of the primary crusher. Once the material has passed the primary crusher the fragmentation size will be fairly consistent and promote consistent throughput of the plant or mill. In late 2015 a team was conducting a reassessment visit to a mining site where we had conducted the original assessment the previous year. Though many recommendations had been implemented some had been so recent they had not resulted in the expected improvements. Several of our discussions kept returning to the impact fragmentation has to both the individual components of the mining cycle but also the effects compounded throughout the end to end process. Let’s move on to the big picture before we zoom in on any specific operation. To get from native solid rock in the ground to a concentrate or a saleable rock product we have the same steps from one end of the chain to the other. We start with a good geological understanding of the rock type, characteristics and structure to design a program to drill and blast the rock. The height of the bench is relevant to the annual production requirements and the specific digging equipment models best sized to make that production possible. The equipment selection influences the bench height which has a minimum and maximum hole diameter to maintain a safe blasting operation. The diameter of hole burden and spacing all contribute to a good distribution of explosives in the rock mass that maximize the fragmentation and preconditioning of the rock when blasted. The timing and sequencing of hole initiation will yield a fragmentation ratio and diggability factor. Fragmentation size adjustments will change the meters drilled per cube and the explosives consumption will change accordingly. Drill cost is measured by meter drilled so a direct relationship exists between cost and fragmentation sized achieved."

Jan 1, 2017

By Leonard Sugin

As we approach the end-of the 20th century we are made more aware of the tremendous role that energy plays both directly and indirectly in our varied way of life. The industralized nations of the world have already established industries and economies which are greatly dependent upon the availability of energy. The underdeveloped and developing nations of the world are slowly and surely moving to the same utlimate requirements. The world wide need for distribution of energy sources is continuing to grow. At the present time there is a great imbalance between the sources of energy and the consuming economies In order to bring about greater equality between supply and demand major efforts and large capital expenditures are constantly being made. Industralized areas are seeking their own independent sources of energy whereas those areas of the world which contain great reserves of energy are limiting its export as well as developing its own industralized capacity. Nevertheless, energy bearing materials are still transported great distances in order to satiate the appetites of power hungry economies.

Jan 1, 1975

By William J. Almas

Operating uranium mill tailings containment and mill decommissioning activities are regulated by the Nuclear Regulatory Commission (NRC) and the Environmental Protection Agency (EPA) through numerous regulatory mechanisms. Reduction of radon emissions from tailings disposal areas, remedial actions to return groundwater to baseline constituent concentrations, and 200-to 1,000-year stabilization of tailings are major focus areas of regulation. The cumulative economic impact and uncertainty associated with regulation are very significant and will hinder future development of uranium milling facilities.

Jan 1, 1991

By James G. Mock

The choice of equipment to be applied to a given installation by the Application Engineer begins with the data as presented to him by the user. This point in the relationship establishes a communication link, which will decide whether or not the correct piece of Overhead Equipment is applied at the most economic advantage to the user. The role played by the user cannot be minimized. No one knows better than he, just what work he expects to accomplish with this piece of machinery. However, all too often, he oversimplifies the requirements, and along with minimal crane and building parameters, merely refers to one of the following crane classifications as defined by The Crane Manufacturing Association of America, as shown in Figures 1, 2, 3, 4, 5, 6 and 7. This approach places the ultimate user in an unfair position, since he has then assumed the status of the machinery designer and must, therefore, assume the responsibility of the success or failure of the operation of that piece of machinery. If the user selects a Class "C" crane for his job requirement, when actually a Class "B" crane can adequately handle the work load, he is not offering the most economic solution to his company and added little to the cranes service capabilities.

Jan 1, 1973

By John S. Cummings

In this paper the phrase "exploration for blind metal deposits" refers to exploration activities geared to the discovery of metal deposits which cannot be located by visual surface inspection. The word "system" refers to all of the components (people, money, corporations, techniques, etc.) which collectively result in an exploration process. The details of the system or systems which I have employed in exploration will not be discussed because of client relationships. However, some of the more severe problems in exploration result from how the system's components interact and our attitudes as to what exploration data is telling us, if anything. It is these items which will be discussed. Exploration for blind metal deposits, which has been relatively intense over the last 2S years compared to rather minor outlays prior to World War II has often been an uncoordinated assortment of various specialists employing various techniques (see Dickerson -1). In a program geared to the location of blind deposits, the lack of outcropping deposits or occurrences should not be a deterrent to a well conceived and well planned program. The severe cyclical swings in exploration activity, although often coinciding with depressed metal prices, by and large result from the failure of exploration operators to present a coherent and realistic program to management. It is my opinion that the stream of complaints criticizing management for cyclical exploration support are mostly unwarranted, as many of the programs and goals are ill defined. Although depressed market conditions may serve as the catalyst for exploration cuts, the underlying cause is that when the "chips are down", the non-directional, non-specific nature of many programs is revealed. Thus management should not be castigated for eliminating such programs during bad times, but rather they should be castigated for supporting them during boom periods.

Jan 1, 1978

By D. R. Tweeton

A modified push-pull field test and a computer model of cation exchange were developed to aid in evaluating cation exchange parameters prior to in situ mining. Reliable determination of these parameters is essential when modeling restoration of groundwater quality. The field test involves a much larger volume and much less disturbance to the ore sample than is feasible with laboratory measurements. This test can be performed in two or three weeks. It is relatively inexpensive, requiring one injection- production well and two or more wells for collecting samples of leach solution. The use of the model in interpreting test results is illustrated with field data from an in situ uranium mine. Much of the research was performed by the University of Texas at Austin, and was partially funded by the Bureau of Mines.

Jan 1, 1986

By Brian H. Kaye

Efficient design of grinding circuits for efficient production of ultrafine material requires rapid feedback of information concerning the fineness of material leaving the grinding device. Generating this information requires efficient sampling and adequate rapid characterization of the material leaving the grinding machinery. Recent developments-in electrooptic inspection of dry end wet material leaving a grinding device are critically reviewed. New methods for characterizing ultrafines are discussed. A rapid operating automated cybernetic (intelligent) permeability device for automatic control of grinding circuits using Blaine index and other fineness indices is described.

Jan 1, 1983

By R. L. Grayson, S. B. Bealko, L. L. Chasko, D. W. Alexander

In response to recent mining disasters and new mine rescue team legislation, NIOSH researchers conducted meetings across the United States with mine emergency response experts to investigate current needs and issues. Some of the issues include emergency response preparedness, mine rescue contests, real-life training capabilities and training facilities. Many new teams are being formed that must be trained for mine rescue team competitions as well as be ready to respond to a variety of mine emergencies, including a fire or explosion, a massive roof collapse, mine inundations or vertical shaft rescue situations. Therefore, it is important that these teams are adequately prepared and trained. This paper presents a summary of domestic and international coal mine rescue training facilities and identifies those that provide unique, real-life and/or state-of-the-art training. Research findings from this report will be used in further NIOSH investigations to improve coal mine rescue training.

Jan 1, 2010

By M. Moats

Copper electrowinning operations have dramatically improved their ability to produce high quality copper at low costs over the past several decades. Even so, some fundamental knowledge is still lacking that could allow operations to run even more efficiently. For example, a rule of thumb exists that estimates a current efficiency loss of 2-3% per gram per liter of iron in the electrolyte. While several laboratory studies have been performed that demonstrate this rule of thumb is likely true, no definitive relationship exists. In this paper, the first steps in developing a definitive relationship are presented. The effective diffusivity of ferric ions in synthetic copper electrowinning solutions was measured using chronoamperometry and the Cottrell equation. The effective diffusivity of ferric ion was determined as a function of electrolyte concentration and temperature. Synthetic electrolytes were then used in laboratory-scaled copper electrowinning experiments, where relationships between current efficiency and solution composition were found to exist under stagnant conditions. Key words: Copper electrowinning, Current efficiency, Chronoamperometry, Ferric ions

Jan 1, 2009

By J. F. T. Agapito

Stability in Exxon's Colony Pilot Mine in the Piceance Creek Basin, Colorado has been monitored by periodic pillar stress-determinations End roof-to-floor convergence measurements since 1971. Pillar failure has caused marginal stability in some areas of the mine. Measurements taken during the process of failure provided valuable information on the in-situ pillar strength and long-term behavior of the mine structure. Four pillars were reinforced by 32 mm (1-1/4 in) diameter tensioned grouted bolts to increase long-term stability in the northern area of the mine. Stability of this area is necessary because future plans envision its use as an exit/access and ventilation exhaust. Computer analyses were performed to help evaluate the effect of pillar reinforcement on long-term stability. Results indicate that bolting is particularly useful in stabilizing failed pillars, but its effects are significant only in the immediate area of the pillar. The projected significant decrease in deformation of two extensively failed pillars near a main entry indicates that bolting reinforcement will assist the long-term stability of the opening.

Jan 1, 1985

By Joseph M. Driscoll

After 30 years of successfully mining gold, Newmont Gold has temporarily ceased production from the original Carlin Pit. In late 1993, the Carlin East decline was driven and an extensive underground exploration program was started. Today, Newmont Gold produces refractory ore from the Carlin East Underground at the rate of 864 t/d (950 stpd). Annual production is more than 3.1 t (100,000 02). More than 70 underground miners will be employed during Carlin East's estimated six-year mine life. About 70% of the ore at Carlin East is mined by mechanized longhole stoping with delayed, cemented backfill. The remaining ore is mined by underhand drift and cemented fill methods.

Jan 1, 1997

Adsorption of acrylamide based homo and copolymers on hematite was investigated as a function of phe nature of the polymer charge and functionality of the polymer. Effect of addition of sodium dodecylsulfonate and dodecylamine hydrochloride was also studied and was determined to result in an increase or decrease in the amount of polymer adsorbed depending on, the charge characteristics of the surfactant and the polymer, pH of the suspension, concentration of the various species and the order in which these species were added to the system. The surfactant adsorption under given conditions on the other hand, was found not to be affected by the presence of the polymer molecules. The data is analyzed to elucidate the mechanism of adsorption of polyacrylanide type polymers on hematite both with and without the surfactant species king present in the system.

Jan 1, 1982

By Y. Zhang, M. Yekich, C. Zhou, C. Jobes, J. Galanko, D. Tuchman, J. Srednicki, J. Carr

The continuous personal dust monitor (CPDM) is an essential instrument for working in hazardous environments, is used to monitor real-time coal dust exposure, and is mandated by the Mine Safety and Health Administration (MSHA) for underground coal mines. Researchers from the National Institute for Occupational Safety and Health (NIOSH) found that it is possible for electromagnetic interference (EMI) between a CPDM and a proximity detection system (PDS) to occur. Various approaches have been taken by researchers and manufacturers to address this EMI issue. Administrative controls were recommended to keep the CPDM six inches away from the wearable PDS device. Shielding pouches were made to contain the electromagnetic (EM) emission from the CPDM. Metal shielding was added to major EM emitting components. EMI filtering with large capacitors was introduced to mitigate EMI. Most recently, a novel magnetic-field-cancellation-based approach was developed and achieved remarkable results. In this paper, we provide a comparison between these approaches. The pros and cons of each approach are presented and discussed, so that mining device manufacturers and operators can best evaluate the technology and controls that improve the health and safety of mine workers.

Feb 1, 2023