Search Documents

Narrow vein mining, with enough challenge and also where the cutting edge technology can be applied, is still a very important and exciting portion of the mining industry. Based on the deposit characteristics, the most flexible mining method, cut and fill, has been being tested mining this high grade Northern Nevada property, Hollister, since the year of 2008. In the last three years, 254,000 tons of ore were hauled out of the portal and 23,000 feet of development were excavated underground with the winning of several safety and environmental awards. Together with mine geology, the essential segments include mining cycle, ground control, ventilation, grade control and backfill method in cut and fill stopes were covered in this paper.

Jan 1, 2012

By Ray Brainard

Treated effluent from the Clean Water Coalition (CWC) member agencies is currently discharged at an annual average rate of 6,570 l/s into the Las Vegas Wash, and is increasing annually. As the effluent flow increases, the nutrient loading of the treated effluent will approach the maximum limits allowed under the current regulations. To manage this flow while maintaining water quality in Lake Mead, the CWC is implementing a 44-km-long conveyance system. This paper discusses the geological and geotechnical aspects of the 13.4-km-long tunneled section through the River Mountains and their effect on design. The tunnel alignment traverses a heterogeneous package of volcanic and sedimentary rocks exhibiting widely variable rock conditions.

Jan 1, 2008

By S. A. Abdel Sabour

Conventional methods for selecting a production plan for an open pit mine is based on the assumption that ore grades throughout mine life as well as market variables are known with certainty. Another important issue that is also being ignored in the conventional procedure is the value of management flexibility to revise operating policy with time according to the arrival of new information. Based on this oversimplification of reality, an optimum mine plan that is thought to be maximizing net present value (NPV) of the project is selected. Given the multiple sources of risk affecting the estimated NPV, there is a high probability that the actual value will be different from that estimated. This could mislead decision making process regarding selecting an optimum mine plan. This paper proposes a multi-criteria ranking system for selection between alternative mine designs under both geological and market uncertainties. The system is based on integrating multiple market and geological uncertainties as well as the operating flexibility to revise the ultimate pit limits using a Monte Carlo-based real options valuation (ROV) model. To compare the methods, the article applies the proposed system, along with the conventional NPV-based method, to rank possible mine designs for a copper and a gold mine. It has been found that, considering multiple risk analysis measures while integrating uncertainty and operating flexibility results in selecting a mine design that is different from that selected by the conventional method.

Jan 1, 2009

By G. V. Krishnan, L. Adler

A rock classification for drilling and boring is presented covering most equipment types and providing an estimation of the key parameters for operation, such as thrust and speed, and of performance such as penetration rate and bit life. Drilling and boring are significant and integral aspects of both the mining and heavy construction industries. Together these constitute over 20% of the G.N.P. Drilling and boring represent the most arduous mechanical processes performed in industry. Their misapplication quickly leads to equipment destruction, hazards, and to major delays. The classification is unified in two ways: 1) for a particular rock class several parameters can be estimated, 2) the classification integrates most excavating activities (i.e. digging, ripping and even blasting), and is derived from ground control. The rock classification provides a job property, based on fundamental and index properties, which yields quick and rough estimates of vital information. However it does not obviate the need for a more thorough analysis, and maintaining field records. BACKGROUND In order to adequately describe a drilling operation the conditions, activity, and equipment must be characterized. Of these the major independent variables are the conditions. Conditions focus on the geologic mass and also consider whether the site is surface or underground. The primary component of the geologic mass is the rock type, detailed below in Rock Characteristics. The other components

Jan 1, 1983

By Brett Campbell

The San Vicente to 2nd Aqueduct Pipeline?Tunnel project is a raw water conveyance tunnel linking the San Vicente Reservoir (SVR) to the 2nd Aqueduct Pipeline via Rancho Penasquitos Pressure Control Facility (RPPCF). This 58,230 lf long tunnel will be 8.5? final ID, and has four points of construction access. The job is classified into 6 Reaches of tunnel, identified by the dominant geology within the reach. This paper will focus on Reach 3, specifically the measures necessary to drill and blast a 550 lineal foot section of granitic rock tunnel immediately in front of an open face digger shield.

Jan 1, 2008

By A. D. Davis, C. J. Webb, C. S. Johnson, J. L. Porter

The abandoned Belle Eldridge Mine near Deadwood, South Dakota, is on land controlled by the U.S. Bureau of Land Management (BLM) property. The mine produced primarily lead and zinc during the first half of the twentieth century. The BLM has expressed concern about acidic drainage as well as elevated arsenic levels in tailings and waste rock at the site. The mine site was evaluated for remediation in 1998 and 1999. Recent reclamation and remediation work included substantial regrading of waste rock, removal of material where metal loading were of concern, and re-routing of drainage from an adit. Trenching at the site shoed a greater volume than originally calculated during site characterization. Material was removed to a repository that was constructed at a nearby drainage divide. Because of physical hazards, the BLM has decided to remove some historic structures. However, a search of mine records and an inventory of archival materials were complete to preserve the history of the site.

Jan 1, 2002

By J. Cole

The Morenci concentrate leach plant construction was completed and successfully commissioned in October 2007. The plant was designed to operate at medium temperature, 160ºC and pressure, 2,100 kPa. The concentrate leach plant utilized many innovative design features. This paper examines the first year?s operation, the challenges, the successes and the lessons learned. The future plans for Morenci concentrate leaching will also be presented.

Jan 1, 2009

By W. L. Jacobsen, T. L. Dyer

Cortez Gold Mines completed a feasibility study for a new openpit gold mine in north central Nevada. The production schedule calls for a peak in material movement. This schedule is based on current operational efficiencies and equipment parameters observed at the company’s existing openpit operation. To mitigate risks of over/under predicting production, simulation modeling was used to validate the loading and haulage requirements during the peak production period. The advantage of simulation is the ability to provide a realistic model of a mining operation based on scheduled and unscheduled random events during the period under analysis.

Jan 1, 2007

By F. S. Kendorski

Several startup or longtime underground stone mines have experienced unanticipated roof control difficulties due to the variable geologic character of the roof strata. Careful mapping of roof conditions, and identification of controlling geologic and mine geometric factors, lead to an understanding of the mechanisms causing roof problems. Factors such as unexpected rolls of the roof strata resulting in a gradual change from strong to weak roof; encountering open water-filled master joints; roof strata delamination due to internal water pressures; local karst features with mud, sand, and water hazards; and sudden loss of limestone roof due to paleo-channel erosion are some recent problems described. Strategies for overcoming these problems are discussed and detailed.

Jan 1, 2002

Steady increases in longwall production have required operators to apply greater quantities of ventilating air in an effort to control and dilute respirable dust. Significant increases in shearer speeds necessitate that longwall supports also be advanced at a faster rate. Both of these factors may contribute to overall respirable dust levels on the longwall face because as supports are lowered and advanced, broken material falling from the top of the canopy is entrained directly into the air stream. To address this issue, the Pittsburgh Research Laboratory collected respirable dust samples from four longwall faces to characterize shield-generated dust. This paper investigates the influence of air velocity and shield advance rates on respirable dust levels. Also discussed are engineering controls currently used to reduce shield dust and alternative controls being investigated by the National Institute for Occupational Safety and Health (NIOSH).

Jan 1, 2009

By Rafael C. Castro

As part of its risk management plan, the South Central Connecticut Regional Water Authority (RWA) is assessing the condition of its system of raw water conveyance tunnels and connecting pipelines. In 2006, the RWA inspected one of the system?s main tunnels, a 4-mi, 1950s-era tunnel that had not been inspected since its construction. The inspection team prepared extensively for the unknown conditions in the tunnel, and the inspection was completed safely and successfully. This paper describes the team?s pre-entry preparations, dewatering and ventilation efforts, surface-to-tunnel communication, access, physical inspection of the tunnel, and the lessons learned throughout the process. Additionally, this paper will preview planning for the subsequent inspections.

Jan 1, 2008

Due to deposit shape and dimension, narrow vein makes reserve modeling, geological control, stope design, drill and blasting more challenging. It needs high standard quality control as errors can be created easily, which could cause significant amount of ore loss or dilution. From channel sampling, survey control, reserve modeling, drill hole design, blasting, communication with underground drillers to backfill, this paper illustrated every step and its quality control of a long hole stope mining. Compared to other narrow vein mining methods (cut and fill and shrinkage), long hole stoping means higher production, less labor, and significantly lower cost when deposit characteristics allowed.

Jan 1, 2012

By Peter Klaver

Deep tunnels have been used for decades for the temporary storage of large volumes of urban runoff, both storm water and combined sewer overflow (CSO). Tunnels are attractive because they reduce surface disruption and do double duty as storage and conveyance systems, collecting overflows from multiple locations and transporting them for treatment to various facilities. Like any hydraulic system, however, there are dynamic effects that must be fully understood during the design phase so that the final constructed product does not have unintended negative consequences. Preliminary sizing of storage tunnels is typically based on the total volume required. For example, if studies have determined that a volume of 56.8 ML (15 million gal) will provide the intended level of control, then that figure can be used, along with a preliminary idea of the desired tunnel length, to compute the required diameter. Of course, filling a long tube with water from various points along the way is not at all the same as pouring water into a bucket, and these dynamic effects require additional attention from design engineers. The rapid filling of storage tunnels can lead to the formation of bores, which are essentially moving walls of water. An open channel bore can build in height until it reaches the crown of the tunnel, at which point it becomes a pipe-filling bore. Figure 1 depicts both kinds of bores moving upwards in a rapidly filling tunnel. Bores can strike the ends of tun-nels with tremendous force, driving water and entrained air upwards into dropshafts and creating strong pressure surges in portions of the tunnel that are already filled. If the hydraulic surges are high enough to reach grade, they can cause overflows and/or damage structures at the surface. Trapped air pockets can occur through several phenomena, including the reflection of bores off dropshaft structures and the occurrence of ?premature pressurization.? The latter refers to the situation where the inflow to a tunnel is increasing more rapidly than the tunnel can convey it, such that the pipe becomes surcharged at an upstream point while points downstream are still flowing as an open channel. These air pockets are a great nuisance as they migrate toward points in the tunnel where they can rise to the surface, which are often shafts that are already filled with water (Fig. 2). The ?geyersing? that results can be hazardous and costly.

Jan 3, 2010

The National Institute for Occupational Safety and Health (NIOSH) has continued study of the Personal Dust Monitor (PDM) developed by Rupprecht & Patashnick Co. Inc. through a CDC contract and currently being commercialized by Thermo Fisher Scientific. This report examines the effect of oversize particles, cyclone inversion, and cleaning procedures. Clean and exposed filters were examined using light microscopy and particulates counted before and after various instrument manipulations. The data presented show that the dry cleaning procedures do not cause significant (greater than limit of detection) sample contamination by respirable or oversize particulates and that the cyclone is resistant to particulate carry over during inversion.

Jan 1, 2009

By D. Brady

When deciding to deploy rescue teams underground the decision makers need to be able to determine that there won?t be an explosion whilst the rescue teams are underground. Previously general body concentrations in areas likely to be travelled were compared to explosive limits on a one off basis with no formal process looking at trends or other areas. A new approach is being adopted that takes into account the rate of change of gas concentrations with triggers set to enable a withdrawal of personnel prior to a possible explosion and influences such a barometric pressure changes. This paper explains the rationale behind the changes made and the advantages and implications of adopting such an approach.

Jan 1, 2012

By Graham A. Davis

?The ideas of economists and political philosophers, both when they are right and when they are wrong, are more powerful than is commonly understood. Indeed, the world is ruled by little else. Practical men, who believe themselves to be quite exempt from any intellectual influences, are usually the slaves of some defunct economist. Madmen in authority, who hear voices in the air, are distilling their frenzy from some academic scribbler of a few years back. I am sure that the power of vested interests is vastly exaggerated compared with the gradual encroachment of ideas. . . . But, soon or late, it is ideas, not vested interests, which are dangerous for good or evil.? John Maynard Keynes The General Theory (1936) Policy analysts, economists and others have tradition-ally considered mining and mineral wealth a boon, providing rich countries with the resources needed to sustain their modern industrial economies while helping poorer countries generate the foreign exchange, tax revenues and other assets necessary for economic growth and development. Nevertheless, this conventional view has always had its critics.

Jan 1, 2008

By I. Nimmo

Since the beginning of Aluminum mining and refining the industry has lived with distributed control rooms and suffered from many behavioral problems common with this design. When Human Factor/Ergonomic design is introduced to a Western Australian installation a common centralized control room realized many improvements including economic payback. Communications issues were resolved, better coordination of materials, improved situation awareness during startups, abnormal operations and an opportunity to make improvements during normal operations characterize the changes at the Worsley Refinery. This presentation will review the reasons for the change. Since the beginning of Aluminum mining and refining the industry has lived with distributed control rooms and suffered from many behavioral problems common with this design. When Human Factor/Ergonomic design is introduced to a Western Australian installation a common centralized control room realized many improvements including economic payback. This presentation will review the reasons for the change, what changed and the process of changing the culture from reactive to predictive and what difference that has made.

Jan 1, 2011

By Alan Weakly

The Powder River Basin (PRB) of northeastern Wyoming and south-central Montana is the largest strippable reserve of compliant coal (0.6 or less lb of sulfur per million Btu) in the United States. In mining parlance, it is the Mother Lode! Wyoming’s portion of the Basin provides one fifth of the coal produced in the United States annually, and the state has been the nation’s top coal producer for the past six years. Based on 1993 production statistics and estimated strippable compliance coal reserves, Wyoming may remain the nation’s top producer for the next 76 plus years. Past articles on the PRB have focused mainly on production. After living and working in the Basin for the past five years, I have developed an appreciation for the area and its major industry that transcends size and production data. In the fall of 1993, MINING ENGINEERING’s publisher and I decided to present a series of articles that would cover many other aspects of the Basin. Ten topics were outlined, and specific individuals, selected for their knowledge and experience, were asked to contribute articles about their specialties. Although Montana has four large mines producing coal from the PRB, this series of articles will concentrate on the Wyoming portion of the Basin.

Jan 1, 1994

By T. Mudder, R. Cellan, R. Waterland, J. Whitlock, B. N. Nelson

The effectiveness of anaerobic in-situ biological treatment for the immobilization of selenium, molybdenum, and uranium in an alluvial aquifer was examined using long-term column tests. A series of organic substrate and nutrient combinations were tested to determine removal effectiveness, optimum supplement concentrations and ratios. Final column testing was conducted to determine the chemical stability of the treatment by-products/treatment compounds by dosing the columns continuously with elevated redox untreated alluvial groundwater.

Jan 1, 2002

By D. Jacobson

There are many different machine setup parameters and variables that affect the production of cone crushers in a mineral processing plant. One of these variables is the eccentric speed at which the cone gyrates. In June 2012, pilot tests were conducted on a 200 hp high speed cone crusher to determine the production and operating conditions over a wide spectrum of eccentric speed. Every plant will have variations in the ore characteristics and feed rates throughout the life of the mine, and at times throughout a single shift of operation, which result in non-optimal use of the crushing energy and inconsistent process control. For high speed cone crushers, the crusher will exhibit a different capacity, power required, and discharge size distribution as the speed ranges over the design limits of the machine. This study documents the measured variation in production and energy efficiency both when the crusher was ran at full capacity as well as when the feed to the crusher was not sufficient to run at full capacity. Overall, the results match theory and the capacity and power fluctuated by 25% and 17%, respectively, over the speed range when operated full while there was an overall trend of slightly coarser discharge size distribution as the speed decreased. The results with the fixed feed rate were more telling, as the crushers had 4-14% higher production when making a theoretical minus 12.5 mm product when operating at the optimal speed as compared to the worst speed in the ?typical? speed range for this application. Secondary analysis of the fixed tonnage testing also showed that the power draw was more consistent with lower magnitude spikes at the higher speeds (higher cavity level), as on average the standard deviation of the power draw increased from 7% to 18% and the peak power spikes from 20% to 48% over the speed range tested. The findings lay groundwork for more efficient plant design. Varying the speed of the crusher can be used to tune the crusher speed during commissioning, adapt to changing ore conditions over long periods of time, or be used as a dynamic input into an advanced control system. Each action above would serve to make the crusher(s) more productive and more energy efficient, and would also have mechanical benefits for the machine. Key Words: cone crusher, ore reduction, process control, crushing efficiency

Feb 27, 2013