Search Documents

Excavations in rock are commonly supported with wire mesh, shotcrete, wire mesh and shotcrete in combination, and shotcrete reinforced with various types of fibres. Wire rope lacing and various types of straps are additional forms of support installed over the above types, to cope with severe conditions. These support systems are very important items of ?membrane? rock support. With the recent development of several types of thin sprayed linings, the importance of membrane support is likely to increase in the future. In this paper, a wide range of mechanisms of membrane behaviour and mechanisms of loading of membranes, is described. The concepts of membrane components, which are single membranes that may be used on their own as rock support, and membrane systems, which are combinations of more than one membrane component, are introduced. Different situations have different requirements of membrane support, and differences between civil engineering and mining requirements are highlighted. With the different basic requirements in these two areas, the requirements of rock support are correspondingly different. A thorough understanding of the mechanisms of behaviour of the different types of membranes, and the different mechanisms by which the membranes are loaded, is essential before a selection of appropriate support can be made, before appropriate design methods and calculations can be determined, and before appropriate performance test methods for membranes can be defined. The material in this paper contributes towards the understanding of membrane support behaviour.

Jan 1, 2001

In extracting base metals from orebodies, sulphide as well as oxide, the main environmental concern is sulphur, whether in the form of sulphurous gases or sulphate in liquid form. Generally sulphur is in over supply in developed countries mainly because of strict legislation to capture it. In developing countries, on the other hand there is usually a shortage of sulphur because of less strict environ-mental legislation. Africa falls in this second category and the African continent imports substantial amounts of sulphur, despite the fact that large quantities of sulphur are emitted by smelters, thermal power stations, coalmines, fertilizer manufacturers and others. Other than making acid from gaseous emissions, existing methods to capture sulphur from gaseous and liquid effluents are uneconomical and it ends up in the environment either as ammonium sulphate (from gaseous effluents) or as gypsum (from liquid effluents). The CSIR?s Environmentek and Key Structure Holdings have developed a process whereby gaseous sulphur emissions and sulphates in liquid effluents can be economically captured and converted into elemental sulphur and metal carbonates. The elemental sulphur is of high purity as it is precipitated from a gas stream and is readily marketable. The metal carbonates (barium or calcium) can be recycled back to the process or marketed. The only harmful by-product of the process is carbon dioxide. Should natural gas or methane be available, the carbon dioxide could be reduced by about one third. Should solar, wind or hydro energy be available to generate hydrogen, the carbon dioxide emissions would be zero. Employing this technology could make Africa independent of sulphur imports and furthermore reduce the impact of acid rain and seepage of sulphate from gypsum and other waste dumps into the environment.

Jan 1, 2005

By G. S. Harper

Noise in general and drilling noise in particular have received increasing attention within the South African mining industry during the last 10?15 years. The Mine Health and Safety Committee1, during their 2003 annual summit, established two significant milestones to be met by December 2008 and December 2013. The 2008 milestone target is that of no more than ten per cent deterioration in hearing among occupationally exposed individuals, whereas the 2013 milestone target is that of less than 110 dB sound pressure levels at any place in the workplace. While these targets relate to general noise within the mining industry, it is widely believed that the most significant source of noise contributing to noise induced hearing loss (NIHL) among the underground workforce, is that of pneumatic rock drills. Data pertaining to the noise emission level of any machine is generally reported as either a sound pressure level or a sound power level of a single machine measured under free field conditions as defined in Appendix 3 of SABS-ISO 37442. However, rock drills are seldom used in isolation and underground conditions cannot be considered as free field. A methodology for the selection of rock drills on the basis of total operating cost has been developed. However, this paper focuses on the noise elements of the generic methodology and provides a model for the prediction of the composite sound pressure level and the equivalent noise exposure levels of groups of individuals from machines, used singly and in combination in an underground environment based on the sound pressure level determined according to SABS-ISO 3744 under free field conditions. The methodology includes provision for the consideration of the effect of hearing protection devices and the use of multiple machines in combination and provides an indication of the potential costs of hearing compensation.

Jan 1, 2006

By J. H. Potgieter

This paper describes two cases of corrosion that occurred in dry-process, rotary, cement-clinker kilns. In the case of the kiln with five pre-heater stages, the attack occurred primarily from sulphates that probably originated in the raw feed and fuel being used in the plant and that penetrated the refractory lining. The corrosion was similar to ash-deposit corrosion often observed in steam boilers. In the second case the plant consisted of a long dry kiln with a single pre-heater fitted to the feed-end. In this case the corrosion could be ascribed to alkali chloride penetration through the refractory-brick lining and subsequent hot corrosion of the kiln shell.

Jan 1, 2004

Abrasivity and wear resistance are not intrinsic properties of materials, but rather parameters describing the interaction between the wear part and the material exerting the wearing action. Moreover, wear or, at least, that part of the wear which is due to the cumulative effect of minute scratches, is linked to the hardness disparity concept. Abrasivity, in this context, is a relative concept, pertaining to a metal-rock pair, rather than to a rock. Based on this assumption, a methodology has been developed and checked against actual cases, enabling description of the abrasiveness of a rock or the abrasion resistance of a metal through the ratio of comparable quantitative indicators. The paper describes the methods and provides examples of applications to practical cases (namely: rock cutting, excavation by means of tunnel boring machines (TBMs), rock crushing, and hydro-mill cutting).

Jan 1, 2012

By C. J. Van Niekerk

The study comprised of the investigation into the sensitization characteristics of AISI 409 titanium stabilized ferritic stainless steel during low heat input welding. AISI 409 is a fully ferritic stainless steel used in catalytic converters and tubing for automotive exhaust systems due to the supposition that sensitization does not occur during low heat input welding. Two plates of 2 and 4 mm were tested for sensitization during low heat input welding. The study confirmed that chromium carbide (M23C6) precipitation occurs on the grain boundaries in the heat-affected zone with consequent depletion of Cr adjacent to the grain boundaries during welding. In the 2 mm plate sensitization occurred in the heat input range of 0.1 kJ/mm to above 0.25 kJ/mm and in the 4 mm plate sensitization occurred in the heat input range of 0.2 to 0.9 kJ/mm. Ti stabilization is ineffective at the heat inputs used in this investigation due to the rapid cooling rate through the temperature region where TiC precipitates. The presence of N was found to be detrimental since it consumes Ti on cooling, forming TiN, effectively lowering the amount of Ti available for TiC formation during rapid cooling after welding. Annealing for 5 minutes at 725°C does not improve the sensitization characteristics of the welded plate. There is a linear increase in grain size as heat input increases. The resistance to pitting corrosion decreases in the sensitized, welded plate in theheat-affected zone adjacent to the fusion line of welding. Keywords AISI 409 ferritic stainless steel, sensitization, grain growth, resistance to pitting corrosion, low heat input welding.

Jan 1, 2011

Abrasivity and wear resistance are not intrinsic properties of materials, but rather parameters describing the interaction between the wear part and the material exerting the wearing action. Moreover, wear or, at least, that part of the wear which is due to the cumulative effect of minute scratches, is linked to the hardness disparity concept. Abrasivity, in this context, is a relative concept, pertaining to a metal-rock pair, rather than to a rock. Based on this assumption, a methodology has been developed and checked against actual cases, enabling description of the abrasiveness of arock or the abrasion resistance of a metal through the ratio of comparable quantitative indicators. The paper describes the methods and provides examples of applications to practical cases(namely: rock cutting, excavation by means of tunnel boring machines (TBMs), rock crushing, and hydro-mill cutting).

Jan 1, 2012

By P. K. Hofmeyr

Base Metal (Cu, Ni, Mo, Zn, Co etc.) analysis traditionally has been very slow in conventional analytical laboratories which can lead to additional costs being incurred in waiting time of drill rigs or mining excessively off-reef. Recent developments in the automation of analytical laboratories now allow for very rapid turn-around times for base metal analytical data which can help reduce such costs as well as reduce the unit costs of the analyses themselves. 2.0 CONVENTIONAL ANALYTICAL LABORATORY PRACTICE Conventional analytical laboratories are necessarily are very manual. Sample preparation is slow and laborious, samples are moved from stage to stage manually and, typically, all samples are processed in batches so a sample which is the first to be, say, milled has to wait for the complete milling of the batch before it advances to the next stage eg. mixed with wax prior to pelletising for XRF analysis. Inevitably this results in long sample data turn-around times for laboratories handling large numbers of samples. Manual sample preparation can only be accelerated by increasing staff which increases costs and can lead to additional errors being introduced. Cleaning of sample preparation equipment, eg. crushers and mills, between samples is essential to avoid cross-contamination between samples and this is slow and labour-intensive. In manual sample preparation the correct sample numbers staying with the samples is totally dependent on the efficiency of laboratory operators. It is extremely difficult to detect when errors have occurred due to the switching of sample numbers during the sample preparation stages. Running duplicates and QC samples at best is only partially successful in detecting when sample number switching errors have occurred. Errors of this nature and cross-contamination problems due to incomplete cleaning of sample preparation equipment tend to occur when laboratories are working at pressure due to high sample numbers and when supervisors are not present during 24/7 laboratory operations which is often required on plant process control laboratories. These problems are common to all conventional analytical laboratories and their magnitude is dependent on the level of control and efficiency of QC systems practised by individual laboratories. The disadvantages of conventional manual analytical laboratories can be summarized as follows:- 1. Labour-intensive which is costly especially when multiple shifts have to be used during 24/7 operations.

Jan 1, 2005

By C. Lottering

Copper sulphate solutions are produced during the pressure leaching of first-stage leach residue in a typical base metal refinery process. Apart from impurities such as selenium and tellurium, this leach solution also contains other precious metals (Rh, Ru, and it) due to dissolution in the pressure leaching stage. Selenium and tellurium are removed from the leach solution by precipitation with sulphurous acid, since these elements negatively affect electrowinning. This study investigates the feasibility of modifying the Se/Te precipitation process step to achieve significant rhodium precipitation in addition to selenium and tellurium precipitation, in order to reduce the rhodium inventory of the process. Thiourea, S02, formaldehyde, formic acid, and sodium thiosulphate were evaluated to determine which of these reagents would achieve the highest Rh precipitation. Based on these screening tests, SO2 and thiourea were selected to be used as precipitation reagents in optimization tests. During these optimization tests, the operating temperature (80 to 150°C) and the amount of reagent added (80 to 140 per cent excess) were varied to evaluate the effects that these operating conditions have on the precipitation behaviour of Rh as well as Se, Te, Cu, and Ni, and to propose appropriate operating conditions. It was found that thiourea resulted in good Rh and Se precipitation (typically in excess of 90 per cent), but precipitated noticeably more copper and nickel from the solution than when SO2 was used. In addition, thiourea had poor Te removal characteristics. SO2 achieved a maximum of 70 per cent precipitation of the rhodium. Faster kinetics and a larger extent of Te precipitation were, however, observed when using SO2 compared to thiourea.

Jan 1, 2012

By J. A. Venter, M. K. G. Vermaak

There are practical indications that flotation recovery of palladium bismuth tellurides is poor. This work tested whether this can be caused by a lack of interaction of the collector with the telluride. Impedance measurements, voltammetry and Raman spectroscopy were performed to determine the interaction of dithiocarbonate collectors (KEX) with Pd-Bi-Te. Impedance measurements showed lower capacitance values in solutions containing KEX indicating the formation of a continuous surface layer. Anodic and cathodic polarization diagrams show the mixed potential tobe higher than the reversible potential of the xanthate-dixanthogen equilibrium reaction; hence the formation of dixanthogen on the surface is possible. Electrochemically controlled in situ Raman spectroscopy did indicate the presence of bulk diethyl dixanthogen on the surface. Raman spectroscopy has confirmed the co-presence of xanthate with dixanthogen, indicating that xanthate retains its molecular integrity when it adsorbs on the surface of the Pd-Bi-Te. As a result, the mineral surface is expected to be hydrophobic and a lack of collector interaction with the mineral is not the reason for low PGM recoveries experienced. Keywords: Raman spectroscopy; Pd-Bi-Te; ethyl xanthate; platinum flotation; Great Dyke; Pd-bearing bismutho-tellurides and moncheite.

Jan 1, 2004

By A. M. Milev

A stand-alone instrument especially designed for recording strong ground motions was used in this study to create a large data base of peak particle velocities measured on stope hangingwalls. A total number of 58 sites located in stopes mining the Carbon Leader Reef, Ventersdorp Contact Reef, Vaal Reef and Basal Reef were monitored. The peak particle velocities were measured at the surface of the excavations to identify the effect of the free surface and the fractures surrounding the underground mining. From the monitoring results obtained, the velocity criterion of 3 m/s will bean adequate value that support systems have to sustain during a rockburst in most cases. However, PPVs in excess of this criterion were recorded, and some PVDs were damaged or irretrieveable, a consequence of which was that possible extreme events were not recorded. The data recorded on the skin of the excavations were compared to the data recorded by the mine seismic networks to determine the site response, defined as the ratio of the measured peak ground velocity to the peak ground velocity inferred from the mine seismic data. The site response measured at all mines studied was found to be 9 ±3 times on average. Values of the site response did not vary significantly with seismological parameters such as peak ground velocity, hypocentral distance and source radius.

Jan 1, 2005

This paper summarizes the results from a project aimed at adapting scroll centrifuges for application to the dewatering of flotation concentrates. The main impetus for the project was to reduce the high cost and footprint size of the technology currently used to dewater fine coal. The technical challenge was to enhance solids capture by incorporating a laser-cut screen into the design of the basket. The project has shown that a pilot-scale scroll centrifuge can be used to dewater froth concentrate. A number of different basket designs were tested, the best results being achieved with a basket comprising a laser-cut screen of aperture 70 µm. The best result on a sample of untreated flotation concentrate, which was taken from the open trough flotation cells at a coal preparation plant (CPP) in NSW was a solids recovery of 82 wt% at a product moisture of 24.3wt%. By comparison the best product achieved with a conventional wedge wire basket was a similar moisture content but solids recovery was only 64 wt%. This could only be achieved after the feed had been artificially thickened. Conditioning of the centrifuge feed with polymer flocculants led to an increase in recovery up to 88 wt% with a moisture content of ca 25 wt%. It is thought that optimizing additive selection and conditioning parameters, as well as screen aperture and open area, could improve performance still further. The results were obtained using centrifuging conditions (centrifugal force, feed solids, feed rate) in the pilot-scale machine which should be possible to translate into conventional designs of commercial scale machines, without downgrading solids throughputs. However only with full-scale trials will it be possible to establish this assertion with certainty.

Jan 1, 2001

By Marco Barla, Mariacristina Bonini, Giovanni Barla

ABSTRACT: The paper describes the characterisation studies of Tectonised Clay Shales at laboratory and in situ scale. The interest relates to tunnelling under squeezing and swelling conditions, in Italy, along the Apennines. The results of monitoring during full face excavation are presented in conjunction with numerical modelling. RESUME: Cet article présente la caractérisation, à l'échelle du laboratoire et in situ, des Argiles Chaotiques. L'attention est portée sur le creusement, dans ces milieux gonflants, des tunnels, dans les zones montagneuses des Appennini, en Italie. Enfin, on présentera les résultats de la modélisation numérique et la comparaison de ces derniers avec les mesures effectuées in situ. KURZFASSUNG: Die Arbeit beschreibt die Charakterisierungsstudien von tektonisierten Schiefertonen, sowohl im Labor als auch vor Ort. Das Interesse gilt dem Tunnelbau unter Quetsch- und Schwellbedingungen in Italien entlang der Apenninen. Die Überwachungsergebnisse des ganzflächigen Ausbruchs werden mit numerischen Modellen präsentiert.

Jan 1, 2003

By P. C. Carrasco

Knowing the origin of the relevant and irrelevant components of the nugget effect is essential to optimize the process under study. This paper describes the causes of the nugget effect and, its dependency on the sample support, sampling density, and on the QA/QC procedures. Several examples of natural and ?human? nugget effect are given. A method to estimate the magnitude of the relevant and irrelevant components is suggested. Finally, the economic consequences of misunderstanding the nugget effect are analysed.

Jan 1, 2010

The corrosion behaviour of a low carbon steel was investigated in natural seawater and various synthetic seawaters. It was found that the steel corroded nearly four times faster in a 3.5% NaCl solution than in natural seawater for an exposure time of 21 days. The corrosion rate after immersion in synthetic seawaters (ASTM D1141 and Marine Biological Laboratory seawater) is similar to the corrosion rate after immersion in natural seawater. Calcium carbonate (aragonite) deposits were found on the surface of the steel after immersion in natural seawater and the synthetic seawaters. Some magnesium-containing deposits were also found after immersion in the natural seawater. These deposits act as a barrier against oxygen diffusion and thereby lower the corrosion rate. The morphology of the calcium carbonate deposits that formed during immersion in the natural seawater is different from those formed during immersion in the synthetic seawaters. This may explain the slightly lower corrosion rates obtained in the natural seawater. X-ray diffraction also showed that the oxy-hydroxides formed in the 3.5% NaCl solution differed from those formed in the other solutions. Keywords: Corrosion, seawater, low carbon steel, 3.5% NaCl, aragonite

Jan 1, 2006

By K. Moxham, R. G. B. Pickering

Over the last few years Lonmin Platinum and Sandvik have embarked on a unique partnership of collaboration through a systematic approach to developing equipment to mechanize and automate narrow reef platinum mining. After the initial design and manufacture of the equipment the key aspect is the integrating equipment, people and method into a mining system. Another key a spec of mechanization is the optimization of equipment utilization and this philosophy has ensured continual evolvement of mining methods. This paper describes the trials and development that have resulted in the mining method described as Lonmin mechanized breast.

Jan 1, 2006

By R. T. Jones

Base metals and platinum group metals can be collected in metallic alloy form, via a wide variety of smelting processes. The recovery, or degree of collection, of the valuable metals is a function of the extent of reduction in the furnace, which, in turn, is indicated by the fraction of iron present in the feed materials that report to the alloy. An equation has been developed that relates the recovery of various metals (such as Ni, Co, Cr, and PGMs) to the recovery of Fe. This recovery equation (for each metal) is characterized by a single parameter (K?) that can either be empirically fitted to the data, or expressed in terms of the equilibrium constant and the ratios of the activity coefficients involved. Data from a number of varied DC arc furnace campaigns are presented to illustrate this behaviour.

Jan 1, 2009

By E. Swart

The purpose of this paper is to provide an overview of the current legislative framework for mine closure within South Africa as well as the new requirements in terms of the Mineral and Petroleum Resources Development Act, 2002. The roles and responsibilities of Government, the mining industry and other stakeholders and confusion caused are also highlighted.

Jan 1, 2003

By M. Görnerup, M. Hayashi, S. Seetharaman, C. -Å Däcker

The mould flux plays a crucial role in the continuous casting operation of steel due to its multi-functional assignment as lubricator and heat flux controller. In reality, the commercial fluxes can fall short of the expectations of the operator. In such cases, the performance of the mould flux reduces production throughput in the casting machine. This paper presents the results of a study of two different commercial mould fluxes in continuous casting of steels. The results of online sampling during casting, as well as off-line measurements in the laboratory, are presented. Mould flux powder and slag samples from the caster have been characterized with respect to melting behaviour, interfacial tension and thermal diffusivity, using various measuring techniques. An experimental technique has been developed in order to simulate the melting behaviour of a flux in the mould, which has been found to be useful for qualitative studies. A cross-sectional view of different powders reveals that up to four different material layers may exist in the bed: a loosely packed powder layer, sintered layer, semi-solid layer and liquid slag layer. It is found that the melting rate of the mould flux is dependent on the liquid slag layer thickness. Thus, in a continuous casting operation the melting rate is likely to be non-uniform with position in mould due to the difference in liquid slag layer thickness. Mould slag composition is found to be influenced by the starting powder for as long as 30 min, representing a large part of the first heat casting time. Observations of gas formation indicate that interfacial reactions between the steel and slag take place. Keywords: continuous sacting, mould flux, mould slag, properties

Jan 1, 2004

By V. Bari?ic

The scheduled power cuts of early 2008 were a disturbing reminder that South Africa needs to expand its power-generating capacity. Low-grade and discard coals, of which South Africa has much, are a source of energy and amenable to combustion in circulating fluidized beds (CFBs). Foster Wheeler (FW) has a long record in developing this technology in boilers. The technology is flexible in burning a variety of fuels; low-grade, high-ash coals, good quality bituminous and anthracite coals, and biomass and waste fuels have all been used. CFB boilers are efficient, reliable and can be designed to meet tight emission standards. In recent years once-through supercritical (OTSC) CFB technology has been developed. It enables the next stage in CFB development to proceed to a medium-scale (500 MWe) utility in such projects as Lagisza, which runs at a net efficiency of nearly 44%. Scaling the technology up to 800 MWe with a net efficiency of>45% is planned to be commercial during 2009. CFB technology can reduce CO2 emissions in the repowering of coal-fired and greenfield power plants. It does so through greater efficiencies and by co-combusting coal with biomass. FW has also developed CFB technology for the gasification of biomass, as, for example, in a pressurized gasifier to produce syngas, which can be used for the production of biodiesel, thereby reducing CO2 emissions from vehicles. Carbon capture and storage (CCS) can potentially cut CO2 emissions in the generation of power from fossil fuels in the short term, provided that it gains public acceptance, that the required regulatory framework is created, and that emission-trading mechanisms or other incentives provide a solid return on the major investments required. Oxyfuel combustion is an option in CCS; Foster Wheeler is adapting its CFB combustion technology for oxy-fuel combustion to meet this challenge. It is developing Flexi-burn?, which enables a plant to be operated either with or without carbon capture. This paper describes the status of CFB technology in terms of boiler efficiency and fuel flexibility. It highlights the advantages of CFB technology for oxyfuel combustion, presents a development plan for Flexi-burn?, and discusses a pressurized gasifier for biodiesel applications.

Jan 1, 2009