Search Documents

The 95th Annual General Meeting of the South African Institute of Mining and Metallurgy was held in the Gold Room of the Transvaal Automobile Club in Johannesburg on Wednesday, 12th August, 1992.

Jan 1, 1992

The 91st Annual General Meeting of The South African Institute of Mining and Metallurgy was held at Kelvin House, Johannesburg, on 17th August, 1988. Mr B.c. Alberts (President) was in the Chair, and declared the meeting open at 16hOO. Obituaries The President announced the deaths of the following members of the Institute:

Jan 1, 1988

Cutting strong rock with a drag bit assisted by high-pressure water jets By M. HOOD. B.Sc. Hons. (Min. Eng.). B.Sc. (Mech. Eng.). A.M.I.M.M. (Visitor) Experiments are described that led to the discovery that coherent high-pressure water jets directed immediately ahead of drag bits while they are cutting strong rock reduce the magnitudes of the forces on the bits significantly. Tests were carried out to assess the effects of the pressure of the water jets on bit-cutting performance. The pressure was varied between 10 MPa and 50 MPa, the water flow rate being a constant 30 I/min. Over this pressure range, the force on the bit was reduced to the extent that the depth of cut of the bit was at least doubled with the point of impingement of the jets optimized. Forces on the bit were found to be particularly sensitive to the point of impingement of the water jets relative to the bit. The optimum configuration was found to be with two jets, one directed towards each corner of the bit and impinging on the rock approximately 2 mm ahead of the leading edge of the bit. Experiments in which a drag bit and high-pressure water jets were used to cut strong abrasive quartzite in the underground mining situation have demonstrated a potential increase of up to five times in the average depth of cut due to reduction of the forces on the bit. The results from the underground tests indicate that the life of the bit is improved significantly - by a factor of approximately two - when highpressure water jets are used.

Jan 11, 1976

By E. Hakami

The objective of the study was to estimate the largest shear displacement that could be expected on a pre-existing fracture located in the repository area, due to the heat release from deposited waste. Two-dimensional numerical analyses using UDEC have been performed. The maximum shear displacement, at the fracture centre, amounts to 0.2 – 13.8 cm depending on fracture parameters. The fracture extension, friction angle and shear stiffness are found to be the most important. Le but de cette étude est de déterminer le déplacement maximal en cisaillement qui puisse se développer le long d'une fracture préexistante en réaction à la chaleur dégagée par les déchets radioactifs enfouis dans la roche. Les analyses numériques ont été réalisées à l'aide du code 2D UDEC. Le déplacement maximal en cisaillement enregistré au centre de la fracture varie entre 0.2 et 13.8 cm en fonction des propriétés de la fracture. L'ouverture, l'angle de friction et la rigidité au cisaillement semblent avoir une influence dominante sur les résultats. Zielsetzung der Studie war die Abschätzung der maximalen Scherverschiebung, die auf einer innerhalb des Endlagergebietes existierenden Rissfläche infolge der Wärmeabstrahlung des eingelagerten Materials zu erwarten war. Es wurden zwei-dimensionale numerische Berechnungen mit UDEC durchgeführt. Die maximale Scherverschiebung im Zentrum der Rissfläche beträgt 0.2-13.8 cm, abhängig von den Risseigenschaften. Dabei hat sich herausgestellt, dass Rissgrösse,Reibungswinkel und Schersteifigkeit den grössten Einfluss haben.

Jan 1, 2003

By J. P. Hoffman, A. S. M. de Jesus

Additions of boron have been found to increase the hot workability of stainless steels. Boron forms complex chromium-iron borides, primarily at grain boundaries but also on delta-ferite stringers. This paper describes how a nuclear technique based on the track-etch method was used to distinguish between borides and chromium carbides on grain boundaries and to investigate the distribution of boron in stainless steels. The method was found to be sensitive for boron, and made it possible for boron precipitates to be identified on grain boundaries and interphase boundaries.

Jan 1, 1989

By P. C. Seligmann

Primary fracture from an array of shotholes by c. M. LOWNDS. B.Sc. Hons. (Rhodes). Ph.D. (Cape) (Visitor) and P. C. SELIGMANN. B.Sc. (Witwatersrand) (Visitor) The effects of stress on the directions of cracks that are propagating in a brittle medium are described. It is shown that the superimposition of stress fields from the holes of an array always adversely affects fragmentation. Consequently, the best fragmentation will result when holes are fired far enough apart in space or time for each to develop its whole crack pattern without disturbance from the others. This concept leads to a philosophy for the design of more effective blasting patterns, which has been verified on model scale and which explains many published, empirical results.

Jan 1, 1976

By J. C. Coetzee

In this article, a case is made for the importance of the transfer and management of tacit knowledge to ensure continued sustainable competitive advantage within the pyrometallurgical industry in South Africa. The state of knowledge management (KM) is assessed through a theoretical and empirical study. The empirical part of the study was conducted by means of a survey questionnaire. An important prerequisite within the research entailed determining the current state of KM within the pyrometallurgical industry, and the findings are presented throughout this article. The research argues for initiatives to address the high turnover of pyrometallurgical knowledge workers. This industry needs to entrench tacit knowledge and therefore address the problems associated with the continuous loss of inherent specialized knowledge. Appropriately, emphasis is placed on identifying initiatives required to embed and retain not only human capital lost through mobility, but rather retaining tacit knowledge through a practical KM framework.

Jan 1, 2012

By D. Limpitlaw

As coal mining often results in the generation of acid mine drainage (AMD), careful planning and management of the water on such mines is required. A colliery in Mpumalanga recently sponsored independent research into the pollution-ameliorating potential of a natural wetland that has been receiving AMD for at least two decades. Samples of the sediment collected in the wetland were subjected to nine stages of sequential extraction in a determination of the distribution of the metal species present. The samples were then analysed for aluminium, iron, and manganese. The concentrations of sulphate-reducing bacteria (SRB) were also determined. The SRB concentration was found to increase with distance downstream (away from the source of pollution). An analysis of the sediment speciation data indicated that metal immobilization may be optimal in areas where the organic adsorption of metals is at its greatest. The analysis also provided evidence of the biogeochemical improvement of the water quality as the AMD passed through the wetland environment. The metal species present did not correlate strongly with the SRB populations; nor did the soluble species correlate with the species formed over long periods of time.

Jan 1, 1996

In many practical situations, calculation of the point semivariogram is not necessary. Such a case is analysed in this chapter. The purpose of this analysis is to give a better understanding of the meaning of the mathematical formulae developed in the previous chapters. A similar problem will be studied in Chapter 11, using the point semivariogram.

Jan 1, 1978

By B. Rainier

This paper discusses the preparation of material for backfilling operations using hydrocyclones. Aspects dealt with include the advantages and disadvantages, material requirements, process constraints, operating systems and equipment of the backfill plant.

Jan 1, 1988

By M. D. Prendergast

Research into the ferrous metallurgy of Rhodesian Iron Age societies M. D. PRENDERGAST (Visitor) Iron-working was a widespread economic activity in Iron Age Rhodesia, and merits historical and metallurgical investigation. However, the research done so far has been incidental and poorly disseminated. This paper reviews the available evidence and the ways in which it can be interpreted by archaeologists and historical metallurgists. Particular attention is paid to smelting techniques and current metallurgical research, and brief suggestions are made for future research. v074n06p254.pdf

Jan 1, 1974

By G. Coetzer, J. C. Davidtz

The substitution of functional groups in covalent trithiocarbonate collector molecules influences the selective and non-selective bonding of collector molecules to mineral surfaces, as well as flotation efficiency in a mixed sulphide ore. These effects were concluded to be related to the metal-sulphide solubility products and electron densities on the sulphur atoms in the collector

Jan 1, 1989

By A. O. Filmer

A study of the dissolution of gold from a pyrite concentrate and from various calcines is reported. The percentage extraction of gold was found to decrease with increasing sulphur content in the material leached because of the porosity of the materials, and particularly because of the passivation of the anodic dissolution of gold when the gold was In contact with other conducting minerals. This is explained in terms of the current-potential curves for the oxidation of gold and the reduction of dissolved oxygen.

Jan 1, 1982

By B. Rohrmann

The paper deals briefly with the history of vanadium, and its uses, price movement, and world resources. It then describes the titanomagnetite ore of the Bushveld Complex, and the production of vanadium from this ore at Highveld Steel & Vanadium Corporation Limited, giving details of the various processes used, including the roast-leach, rotary-kiln, electric-smelting, shaking-ladle, and basic-oxygen-furnace operations. The paper concludes with a very brief account of the treatment of Highveld slags in Europe for the production of vanadium pentoxlde and ferrovanadium.

Jan 1, 1985

By D. J. Adams, R. G. Gürtunca

This paper describes the results obtained from a rock-engineering monitoring programme carried out at West Driefontein gold mine, where dewatered and classified tailings have been used as backfils for local and regional support. The in situ behaviour of these backfils and the surounding rockmass were determined, and it was found that the backfil used on this mine has provided significant regional support. The underground observations also showed less rockburst damage in backfiled panels than in unfiled panels, provided the backfil had been placed properly in the stopes.

Jan 1, 1991

By P. J. Kinver

The paper presents details of the costs and outputs being achieved by South African mechanized tunneling and stoping drillings. The information was gathered from various hard-rock mining and tunneling operations ranging from deep-level gold mines to shallow base-metal mines. The survey included older pneumatic rigs and the newer electro-hydraulic rigs, but excluded shaft drilling and the stope drillings that were developed recently for narrow reefs. The information presented is intended as a guide to those having to decide whether to use mechanized drillings and, if so, what type and quantity

Jan 1, 1990

By J. A. Tyser

The pumping of water from mines in the Central Witwatersrand by J. A. TYSER, Pr. Eng., B.Sc. (Min.) (Associate) This paper describes a system for the removal of underground water in the mines of the Central Witwatersrand, some of which are defunct. The water is pumped by a pump station on 24 level at E.R.P.M. to a surface lime plant and then to a surface treatment plant, where it is treated so that it meets the specification of the Department of Water Affairs relating to the deposition of water in public streams.

Jan 5, 1977

By A. J. Jager, G. R. Adams

The pattern of mining-induced fractures ahead of stope faces in deep-level gold mines, as revealed by petroscopic observations, is described. It is shown that there are zones of fractured and unfractured rock ahead of the face, which are about I m wide and continue as discrete entities for at least 12 m parallel to the face and at least 5 m vertically. These zones do not form continuously as mining progresses, but develop from time to time, leaving a solid zone between the fractured zones. The maximum depth of fracturing ahead of the face depends on the rate of energy release.

Jan 1, 1980

By S. Nana, M. B. Cortie

Duplex stainless steels containing high levels of manganese and copper and lower-than-normal levels of nickel were produced and evaluated. The experimental alloys containing 3 per cent copper by mass could not be successfully hot-rolled. Alloys containing less than 2 per cent copper could be hot- and cold-rolled without difficulty. The wrought experimental alloys that contained copper were found to offer some advantages over the 2205- type duplex stainless steel in sulphuric acid at 52°C. Resistance to pitting attack was governed primarily by the chromium, molybdenum, and nitrogen contents, and one of the experimental alloys was superior to the 2205-type alloy in the ferric chloride test. It is concluded that manganese is a useful substitute for nickel in duplex alloys, but that further work is required before the present alloys, or variations of them, could be commercially viable.

Jan 1, 1993

By R. Hoare

TSG Consulting works with many of the major global mining companies using simulation modelling as an integral component in their development team's processes to determine which combination of infrastructure options, operating performance and operating rules best achieve project goals. All systems can be divided into a series of subprocesses. Conventional management and design practices focus on the optimisation of these system components. However, the interaction between subprocesses means that improvements made to the individual components do not necessarily translate into total system performance improvement. TSG Consulting advocates a `total integrated system approach' to understanding the behaviour and performance of complex interacting systems. In a constraint-based integrated set of processes, the instantaneous system capacity is limited by the subsystem component capacity that is the bottleneck at that point in time. Additionally, real world stochastic and dynamic influences tend to have knock-on effects across subsystem boundaries. This necessitates the requirement for simulation modelling to develop and validate solutions that are sufficiently robust to deliver sustainable outcomes. The key to maximising production is to understand the causes and effects the inherent variability has on component performance, subprocess performance and most importantly, the total integrated system performance. The correct use of simulation modelling techniques allows study teams to evaluate the relative merits of different capacity enhancement proposals. Put simply, when done well, simulation modelling provides a quantitative and rational process to enhance the knowledge and insight needed to make informed decisions.

Jan 1, 2007