Search Documents

By M. Timucin

High-temperature phase relations in the Pb-PbS system were established by the quenching of samples equilibrated in evacuated and sealed silica capsules. The liquid-miscibility gap seen in some previously published phase diagrams was not observed. The thermodynamic activities of PbS in liquid solutions of this system were derived at 1473 K from the isopiestic equilibration of samples belonging to this solution series with Cu2S-PbS melts of known PbS activities. The behaviour of Pb-PbS melts was found to be compatible with a subregular solution model. This model also made it possible to obtain an analytical liquidus for PbS that was in excelent agreement with the experimental determination.

Jan 1, 1988

By A. M. Copeland, A. J. Barrett

The use of hydraulically placed backfill in the deep gold mines of South Africa has increased rapidly over the past decade. The backfill that is delivered to the placement areas has a relatively high moisture content, and it is therefore pumped into geotextile containment bags that allow excess water to drain out but retain solid particles. The specific problems associated with this process that are addressed in this paper include the loss of solid particles entrained in the excess water, the rate of strength gain of the backfill, and the post-placement shrinkage of the backfill. The results of laboratory, surface stope, and underground tests are described. The parameters that were varied included the slurry density, the particle-size distribution, and the feed rate of the slurry the concentration of added flocculant; and the type of geotextile used as containment. Suggestions are given for the optimization of the placement properties of backfill.

Jan 1, 1994

By W. A. Lenhardt

During the past five years, several research projects on the causes of mining induced seismicity have been carried out by the Rockburst Research Department at Western Deep levels Limited. This paper summarizes the results of these investigations. Several types of mining-induced seismic events are addressed, and models of their mechanisms are presented. It is shown that most of the seismicity results from mining in geologically disturbed areas, and ways and means are discussed to reduce the seismic potential. Stabilizing pillars, for instance, have been introduced to reduce stresses at the stope face and to alleviate the facebursting problem. Facebursts still occur in areas of very low stresses, and pillars became the source of very large seismic events (M >3). At this stage, the understanding gained of pillar-associated events allows a review of current mining practices. Further, it makes possible an examination of the efficiency of measures to alleviate the effects of various seismically prone situations.

Jan 1, 1992

By P. W. J. van Rensburg

COLLOQUIUM AND GENERAL MEETING A General Meeting and Colloquium on comminution was held on March 13th, 1974, at Kelvin House, Johannesburg. Mr P. W. J. van Rensburg (President) was in the chair. The Colloquium was attended by 140 delegates and was opened by the President at 9.15 a.m. MINUTES The minutes of the general meeting held on November 14th, 1973, as published in the December issue of the Journal, were confirmed.

Jan 5, 1974

By G. L. Gomes-Sebastiao, W. W. de Graaf

"Gomes Sand is a quarry operation that produces sand and aggregate for the construction industry. The quarry is experiencing inconsistencies in the fragmentation and poor pit conditions as a result of poor drilling and blasting practices. This results in excessive downtime in the load and haul and crushing processes.A benchmarking exercise of the blasting practices was conducted to evaluate the effect of the inconsistency on the mining cycle. After changes in the blasting practices the downtime was reduced, which improved the crushing plant utilization by 4.9%. The improved blasting practices and more consistent fragmentation decreased the average number of loads lost each month due to jaw crusher blockages from 9.2% to 3.9% of plant throughput. The change in blasting practices also improved pit conditions. IntroductionGomes Sand is a quarry operation that has been in operation since 2009, producing sand and stone for the construction industry. The quarry was experiencing unacceptable blasting results. The repercussions included uneven pit floors, large amounts of oversize rock (>500 mm), and inconsistent fragmentation.The blast results affected the load and haul operations as well as the efficiency of the crusher. This resulted in downtime in the daily operations, and consequent production and revenue losses.The crusher product should have a top size of 50 mm. A blast fragmentation of <50 mm would improve the downstream operations and the crusher throughput.An investigation into the blasting practices was carried out to assess whether the downstream delays can be eliminated by improving the blast results. The exercise included:* Assessing if the designed blast layout is adhered to on the bench* Observing the quality and control of drilling* Observing the charging procedure of the blast-holes* Benchmarking the fragmentation consistency of the blasted rock using current blast design and practices* Analysing the throughput of the crushing plant* Investigating the power consumption of the crushing plant and determine if a change in blasting practices will affect this* Evaluating the hours spent by the hydraulic hammer on secondary breaking."

Jan 1, 2017

By C. L. M. Gough, L. A. Vermeulen, D. D. Howat

Formulae expressing the dependence of the mass of a grinding ball on the amount of material milled by a ball mill are derived. It is shown that, with the aid of these formulae, it is relativel rsimple for the results of a marked-ball test to be analysed and for the relative performance and cost-effectiveness 0 the various types of ball under test to be evaluated. Predictions based on theory and the results obtained in a marked-ball test in a ball mill are compared detail and shown to be in close agreement. The difficulties associated with marked-ball tests are considered, and an explanation for the decrease in the calculated consumption of the balls, which follows naturally from the theory, is presented. The marked-ball anomaly explained, and it is demonstrated that the ball consumption in a ball mill can be predicted with fair accuracy from the results of a marked-ball test.

Jan 1, 1983

By M. U. Ozbay

The stability of pillars is analysed on the assumption that pillars shed load in a stable manner if the slope the strata load-deformation relation is steeper than that of pillars in the post-peak regime. Concepts of local stiffness, mine structural stiffness, and critical stiffness are discussed. Procedures are described for the determination of strata stiffness for various pillar layouts by use of the available boundary-element computer programs. The postpeak stiffness of pillars is assessed from the available data relating to the post-peak load-deformation relationship and width-to-height ratio. Stability analyses are carried out by the contrasting of strata stiffness with post-peak pillar stiffness. It is shown that the strata stiffness becomes unacceptably small for a stable yield-pillar layout when the span exceeds about 5 times the depth. The strata stiffness is found to increase, thereby increasing the stability, as the span-to-depth ratio, number of pillars, and percentage extraction are decreased. It is also found that the stability in a yield pillar becomes difficult to achieve when al the pillars in a layout are in the descending part their post-peak load-deformation curve

Jan 1, 1989

By N. B. Strydom

Die bedryfsfisioloog en lugbesoedeling N. B. STRYDOM, Ph.D. (Phys.) (Illinois) (Genoot) Although the industrial physiologist can still be regarded as a rarity in South African industry, it is obvious that he could make a positive contribution to the control of air pollution. For the past twenty-two years, the gold-mining industry has invoked the aid of industrial physiologists in solving various problems that continually crop up in the more effective and safer utilization of man-power. Air pollution is only one facet that has received attention. It can be stated emphatically that other industries could gain many advantages from the employment of this type of specialist. Because of inadequate opportunities for academic training, however, the industrial physiologists available might not be enough to fill all the possible posts in industry at present, but confidence is expressed that interested persons will soon be able to follow a full university course in this field of study.

By D. P. Enright, D. D. Howat

Austenitic manganese-steel castings are very widely used in crushing and grinding in the&apos; gold-mining industry in South Africa, The service life of a casting in a short-head crusher is difficult to predict because there are no clear-cut criteria by which such a judgement can be made, The addition of molybdenum and zirconium to the castings for crushers failed to result in improved performance, The results of extensive tests with through-hardened steel castings were very disappointing, mainly because of a design factor in the bowl liner. The design of the bowl liner is an important determinant of the life and performance of these castings. The extent to which the material in a crusher is reduced in size has profound effects on the consumption of metal and power, and on the effective life of a casting. Tests on manganese-steel castings in an 8 ft by 12 ft rod mill provided data on the total consumption of metal, and on the variations in the pattern and rates of wear of liners over lengthy periods. Progressive changes in the wear profiles of the lifter bars and the other liner components showed unexpected features. There are clear indications that, whereas a set of lifter bars will at first lift the charge strongly with relatively little slippage, there is a later period characterized by more slippage and greater wear on all the liner components.

Jan 1, 1980

By B. Strohmeier

An account is given of the use of a computer to control the performance of three ultra-high-powered electric-arc furnaces in Iscor 5 steelmaking plant at Vanderbijlpark, South Africa. Several of the reports and graphs printed by the computer are reproduced.

Jan 1, 1985

By D. M. Meyer, K. Auerswald

The production of electrolytic manganese in South Africa by M. HARRIS, Pr. Eng., B.Se. (Eng.) (Fellow), D. M. MEYER, Pr. Eng., B.Se. (Meeh. Eng.) (Visitor), and K. AUERSWALD (Visitor) The decision to construct the first electrolytic manganese plant in South Africa was important and farreaching. After evaluating the results of the pilot plant operation, the first South African producer, Electrolytic Metal Corporation (Emcor), established a plant in Krugersdorp. Initially, there were many process problems that had to be InvestIgated, and, after these had been solved and many operating parameters had been established, manganese was successfully produced. When the Delta Manganese plant in Nelspruit was planned, cognizance was taken of the fact that, if peak efficiencies were to be maintained, the process must be operated between fairly narrow parameters. Instrumentation was therefore installed to control the process automatically wherever possible. The main features of the Delta Manganese operation are outlined, with a brief description of each stage of the process from ore milling through to electrowinning and packing of the metal. It is concluded that much benefit can be obtained from further research work into process improvements and into the exact effect of certain variables on plant and current efficiency.

Jan 2, 1977

The FSPE Award for Services to the Engineering Profession was awarded to Or Francis George Hill at a ceremony held in January of this year by the Federation of Societies of Professional Engineers. The following is an abridged version of the citation made by Professor A.N. Brown, President of FSPE, and of Or Hill?s reply. Achievements. It is indeed fitting that such a distinguished group of people have gathered on this special occasion to honour and pay tribute to Or Pinkey Hill

Jan 1, 1988

By G. S. Hansford, J. W. de Kock, C. D. Levy

Rheological measurements on pulps from South African gold mines by G. s. HANSFORD, Ph.D. (Pennsylvania), M.Sc. (Cape Town), C. D. LEVY, B.Sc. (Eng.), and J. W. DE KOCK, Ph.D. (Cantab.), B.Sc. (A.I.C.) (Visitors) A method is described for the determination of the rheological parameters of a fast-settling slurry with conventional viscometric measuring equipment. The effect of concentration, temperature, and pH on these parameters is investigated. The results agree with those obtained by previous workers using different viscometers, but this method allows a more detailed characterization of all the properties. From a literature survey, two semi-empirical equations were found that allow the effect of concentration, temperature, or pH on the rheological parameters to be correlated.

Jan 3, 1976

By D. S. Loubser

The technique of backfilling in the gold mining industry is dependent on the dewatering of slurry to form a solid support system. In many cases flocculants are added to the slurry to increase the rate of dewatering. To ensure that a stable support is obtained it is important that the chemistry, application and limitations of these flocculant additives are understood. Flocculant additives have to be added at a point where minimum shear will occur. (Shear occurs when a flocculant is exposed to excess energy resulting in breakdown, of the floc.) To ensure that optimum results are obtained it is important that personnel involved are trained to use the flocculant additives and dosing equipment correctly.

Jan 1, 1988

Solvent loading: It is agreed that it is advantageous, as far as reagent cost is concerned, to operate at maximum solvent loading. However, owing to the fact that no reliable automatic solvent flow controller is yet available, control tends to be erratic with the result that there is risk of losing uranium. As can be seen from Mr Tunley&apos;s plot, the graph representing total ammonia cost is fairly flat between loadings of 3.5 and 4.0 gpl, while the graph representing uranium loss in the raffinate is steep. It is, therefore, safer to operate slightly below optimum loading in the absence of absolute control. Should the purity of the final product gain importance, operation at optimum loading or even slightly above, may be advantageous. Solvent losses and clarification of pregnant solution: The cost of replacing solvent, as indicated by Mr Carman, represents a high percentage of the overall Purlex costs. It is, therefore, agreed that, amongst other factors, efficient clarification of the pregnant solution and mixer-settler design have an important bearing on the cost. However, as at Blyvooruitzicht, the Buffelsfontein plant can tolerate a suspended solids content of 50 ppm without serious deterioration in efficiency. An increase in the suspended solids content from 15 to 50 ppm normally accounts for an increase of approximately 1 ppm in amine loss. Clarification of acidic pregnant solutions is much more difficult than that of alkaline solutions. Sand clarifiers are being used at Buffelsfontein with moderate success. Clarified solutions containing less than 20 ppm of solids in suspension can be produced, depending on the quantity and type of flocculant used in the filtration process, the thickness and the grading analysis of the sand beds and the quality of supervision. An on-stream duty of approximately 0.15 gallon per sq ft of surface area is obtained. Hydraulic handling of clarifier sand, while cleaning, may effect the efficiency of a clarifier, as size segregation of sand particles may lead to inefficient "pockets" in a sand bed. Control of the solution level in the sand clarifier also affects the quality of the effluent. Exposure of the sand bed invariably causes a cloudy effluent. Recycling of the final and initial solution discharged before and after skimming the clarifier sand improves the clarification efficiency significantly. Post-precipitation of silica and possibly sulphate salts, after clarification, may give a false impression of inefficient clarification. This phenomenon is more pronounced when treating hot supersaturated solutions. Ageing and cooling of the solution before clarification assist in stabilising the solution and reduce precipitation after clarification. The maintenance cost of sand clarifiers at Buffelsfontein is in the order of 0.35 cent per metric ton of solution treated. A redundant ion-exchange column has been tested successfully, either as a primary or a secondary clarifier, depending on the quality of the filtrate treated. The conventional pebble and sand beds in the column have been retained. Operation was enhanced by the addition of a two-foot deep resin bed as a filtering medium. The suspended solids content was reduced to less than 5 ppm. Mixer-settlers: Mixer-settler design is a controversial subject but, in view of the high costs of solvent compared to relatively low pumping costs, it is believed that mixing and pumping functions should be separated. Separate facilities for pumping and mixing not only give greater operational flexibility but also permit eventual changes in the flow circuit as technology develops. Scrub technique: Unlike the pilot plant, where the crud was carried away in the aqueous phase, crud is carried over with the organic phase in the full-scale plant. This carry-over of crud into the strip bank aggravates crud formation in the first strip stage. This phenomenon may result from a slight difference in settler design and/or a variation in the relative phase depths in the two plants. Bypassing of the scrub aqueous solution from the fourth to the second stage was introduced in order to avoid dilution and partial neutralisation of the acid added to the third stage, as it is known that a low pH value enhances the transfer of iron into the aqueous phase. The low aqueous flowrate in the third scrubbing stage was overcome by introducing an aqueous phase recycle. Gleaning: Mr MacDonald&apos;s contribution on "gleaning" was most informative. This process for recovering solvent from raffinate seems to show at least as much promise as coalescers and other methods employed to date. Similar tests conducted at Buffelsfontein pilot plant gave 60 per cent amine recovery from raffinate containing 10 ppm amine. However, the circuit was not operated at equilibrium and recovery may be expected to drop as the amine concentration of the "Gleaner" circuit increases.

By C. G. Schmidt, N. W. Hanf

Many of the pyrite concentrates produced at South African gold and uranium mines contain economically significant amounts of nickel, copper, and cobalt, apart from gold and uranium. In some cases these concentrates are leached for uranium, followed by roasting and cyanidation of the calcine for the extraction of the gold. Even if their intrinsic value is excluded, the presence of appreciable amounts of base metals can lead to excessive consumption of cyanide and zinc in the conventional process for the recovery of gold from calcines. The extent to which base metals, particularly cyanocides in the calcine, can be made soluble in water or in dilute acid by variation of the pyrite roasting conditions was investigated. An important finding of the investigation was that the conditions producing favourable base-metal sulphation (and hence solubility in water) also produced good sulphation of the uranium values that had not been extracted in a conventional leach of the original pyrite. Thus, if the pyrite is subjected to a sulphating roast followed by quenching in water (or dilute acid), it should be possible for the uranium to be extracted in improved yield. The need for leaching of the pyrite would therefore fall away. It was noted that sulphation roasting also resulted in improved gold extractions when the calcine was subsequently subjected to conventional cyanide-extraction procedures. From well-sulphated calcine, the dissolution of base metals and uranium appeared to be fairly independent of leaching pH, time, and temperature. On an inadequately sulphated calcine, Iow pH values during leaching gave increased extraction of copper and uranium but did not have a significant effect on the dissolution of nickel and cobalt. The extraction of uranium increased with increasing leaching time and temperature, while only longer times at a Iow pH value markedly improved the extraction of copper. The extraction of cobalt was fairly independent of leaching time and temperature, but the results were insufficient for a conclusive evaluation to be made of their effects on the dissolution of nickel. A cursory economic assessment &apos;indicated that sulphation roasting applied to the pyrites investigated is likely to be very profitable.

Jan 1, 1979

By A. Morley

It is difficult to evaluate exploration properties in a manner that is transparent, repeatable and easily re-calculated to cater for different geological interpretations, but the risk-based assessment methodology, the Geological Risk Method, developed and described by Lord et al (2001) attempts to satisfy all these criteria. This paper examines a case study example based on valuations of exploration projects conducted by SRK Consulting using this methodology, and describes some of the advantages and limitations of the method.

Jan 1, 2007

Performance testing is often used by project owners and financiers to provide protection from, or assessment of, technical aspects of project design, procurement, construction and commissioning. The performance tests can range from comprehensive performance warranties relating to process performance and production in the case of lump sum turn key (LSTK) projects to less onerous demonstration tests for cost reimbursable contracts. This paper will discuss performance testing from both the contractor&apos;s and owner&apos;s perspectives and focuses on: ? when performance tests are required, ? what type of performance test/warranty is optimum for each type of project, and ? how project performance should be evaluated. The requirement for performance testing can be driven by the project financiers, particularly in the case of smaller resource development companies. In such cases, differentiation between owner&apos;s risk and contractor&apos;s risk can become contentious. At the other end of the spectrum, larger mining houses may choose to heavily influence the engineering and design process with the contractor supplying services on a reimbursable basis. In that case, the performance testing process is often limited to demonstration tests that validate performance for the owner&apos;s corporate governance requirements. This paper was prepared due to the lack of published benchmarking of performance testing and the resultant differences in expectations between a contractor and a project owner that often surface late in the contract negotiation process. The paper provides a checklist of requirements for both the owner and the contractor that may be used to provide `common purpose&apos; early in the contract negotiation process.

Jan 1, 2007

By A. S. Nhleko, P. R. Lobe, H. Mtegha

"Government’s equity role in the minerals sector is one of the nationalist measures implemented in order to ensure greater control and management of a country’s mineral resources. This paper evaluates the Tanzanian government’s equity participation in the minerals sector from 1996 to 2015. The research methodology included determination of the number of mineral rights, minimum allowable exploration expenditures in prospecting licences (PLs), and forms of equity role of the government. Data was collected and analysed for PLs, mining licences (MLs), and special mining licences (SMLs).The study revealed a number of challenges faced by the Tanzanian government as regards its equity strategy in the mineral sector. One of the major challenges was the secrecy surrounding agreements and contracts entered into between the government and private sector investors, which were concluded via various business ownership and mineral development projects. This secrecy resulted in non-transparency and lack ofaccountability in the mining industry.The financial benefits accruing to the government were inadequately realized, evident through inconsistent payments of corporate income tax and mining royalties by the mining companies. Furthermore, the government does not have solid mechanisms and frameworks for assessing non-financial benefits, thus it is difficult to measure the impact of these factors.It is recommended that the Tanzanian government review the Mining Act and Regulations of 2010 to include the provision of solid mechanisms and frameworks for all forms of government equity role.This paper is based on an MSc research study undertaken at the University of the Witwatersrand.IntroductionGovernments can grant private companies mining rights to extract mineral resources, or take a stake in the companies as well as establish state companies to oversee their interests in the minerals sector. The establishment of a state company to oversee government interests in the mining sector implies the direct participation of government by way of equity participation. Equity participation or role is defined as the holding of shares in an enterprise, company, or asset by individuals or a body corporate (Otto, n.d.; Brown, 2013; Natural Resource Governance Institute, 2015)."

Mar 1, 2019

By A. L. Hinde

A review of real-time particle size analysers A. L. HINDE,. B.Sc., A.R.C.S., D.I.C., Ph.D. The physical principles of different sizing techniques are critically examined in order to evaluate the suitability of the techniques for real-time particle size assessment. Examples of both successful and unsuccessful attempts at producing an acceptable real-time sizer are described in order to delineate the difficulties involved in making rapid and accurate size measurements. Only two of the examples described have proved to be suitable for on-line particle size monitoring, namely the "MintekjRSM Onstream Slurry Sizer" manufactured by Cartner Group, Ltd., and the "PSM System 100" made by Autometrics Co. Both these commercial systems are capable of assessing particle size with an accuracy comparable with that obtained by routine sieving and weighing. The "PSM System 100" has been used successfully for automatic control of grinding circuits. Economic benefits derived from this system, operating under rigorous plant conditions for several months, have proved that real-time size analysers are of significant value to the mining and metallurgical industry.