Search Documents

By C. J. Van Niekerk

When gold plant residues are cycloned for producing a coarse product for backfilling the gold and uranium values are upgraded in the backfill product. Gravity concentration, wet high intensity magnetic separation and froth flotation were investigated as first-stage recovery processes to recover these economic values from backfill prior to placement underground. This paper addresses the recovery of values from flotation concentrates and also details the economic feasibility of a treatment route including flotation, followed by roasting of flotation concentrate to liberate gold entrapped in pyrite and reverse gold leaching of the calcine so produced.

Jan 1, 1988

By Y. G. Che, M. Brown, R. L. Gandhi, M. D. Watson

Slurry pipelines have proven to be an economical method of mineral concentrate transport over long distances. Some of these pipelines are internally lined with high-density polyethylene (HDPE) to avoid internal corrosion. HDPE is an inert and extremely smooth material, and it was believed hat scale deposits would not form on it. However, there have been instances of scaling on HDPE lined pipes. Scale problems have also occurred on bare steel pipes. In this paper experience with scale problems in some of these pipelines will be summarized. Alternatives available for control of scale problems will be discussed, and a success story for the control of scale problems in the 300 km long Century zinc and lead slurry pipeline will be presented.

Jan 1, 2007

The block caving mining method is used to mine large orebodies in weak rock types. The layout for block caving requires that a considerable amount of development is carried out on the extraction drives and drawpoints at the bottom of the caving block. The development further weakens the rock mass, and stability problems arise in the extraction drives and extraction pillars. This paper describes the application of three-dimensional boundary element models in analysing alternative extraction level layouts for a block caving mine. The objectives were to establish whether the use of lateral pillars between drawpoints was warranted, and whether the lateral pillars should be offset or not. The stability of the rock mass within the pillars as well as the stability of the extraction drives were taken into account. The results showed that after undercutting, the horizontal and vertical stresses in the extraction level would be reduced. The lateral pillars would significantly improve the stability of the extraction pillars and extraction drives. There would be a minor improvement in stability if the lateral pillars were offset.

Jan 1, 1987

By L. Wade

The advent of relatively cheap computing power has precipitated a rapid growth of computer usage in the mining industry. In order to obtain most benefit from this development a need is recognised for the future mining graduate to be trained in computer literacy. This paper outlines the type of training required and describes progress to date with such a programme at the University of the Witwatersrand. Certain challenges concerning the teaching effort are discussed.

Jan 1, 1987

By J. A. L. Napier

An analytical solution to the best choice of cutoff grade for a mine is deduced for an assumed model of selective mining. It is found that this choice is determined by the constancy of a special function, the Hamiltonian, over the life of the mine. It is suggested that the appropriate constant value for this function should be determined by the expected long-term average of the paylimit. In that case, the optimum profile can be calculated at each point in time according to the prevailing working cost and product price. In particular, a decision can be made between operation at the true paylimit or at the subsidized paylimit implied by either the lease and tax formulas or the assistance formula for gold mines. It is also shown how the basic formulation can be extended for 'use in the determination of the optimum joint paylimit for two products over the life of the mine.

Jan 1, 1983

By D. J. Mourant

Day-to-day operations on the Broken Hill mine of the Black Mountain Mineral Development (BMMD) Company require a detailed knowledge of the distribution of the ore minerals within the orebody. The data are acquired by systematic underground diamond drilling of the orebody and subsequent geological and analytical borehole logging. These data are then captured onto a database, available for further analysis. Before mining commences in a mining block, copper, lead, zinc, silver and bismuth assay values, and the specific gravity of each sample, are extracted from the database. 3-dimensional variogram and kriging calculations are performed for each geological zone; for all the metals of interest. A computer representation of the mining block in the form of an ore model is then built using these kriged data. From these ore models information is extracted as required by the Geology Department on the mine, and used in numerous operations. These include: daily grade control to supply optimum feed grades to the treatment plant; the compilation of short, medium and long term production schedules; orebody outline definitions for the detailed planning of mining operations; ore resource calculations. The system has been modified and updated since its inception and provides timely information in a production environment.

Jan 1, 1987

By L. Dison

There are many potential uses in gold mining for an initially stiff element of backfill that will yield at a predetermined load and maintain that load to beyond a compression of 30%. Such elements could be used as yielding rib pillars, as replacements for more conventional supporting packs, as con- fining bulkheads for mass backfill, as supports to provide lateral constraint, and load-carrying augmentation to overloaded rock pillars. The paper describes a system of reinforced cemented backfill that can be used to provide the above requirements. The necessary characteristics of the reinforcing and the cemented tailings are described together with the method of design to obtain a predetermined stiffness and yield load. The load-compression characteristics of the reinforced tailings elements are described and the effect of changing various of the design parameters is demonstrated.

Jan 1, 1988

By E. Dadzie

This paper will review some methods used to manage geotechnical risk at Damang Pit Cutback. The pit depth is designed up to 250m with push back on the eastern and western walls of the existed and depleted Railway Cutback (RCB) pit. The geotechnical design was presented by SRK Perth, focussing on the optimisation of the bench face angle which finally evolved with ?steep slope strategy?; 24m at 800 and 24m at 750 on the eastern and western walls respectively. The east wall was designed strategically to optimise the proximity of the tailings dam to the final pit crest of the push back. The pit has experienced failure in the weathered profile transgressing through the transitional material into the fresh rock at different location of the east wall since development in July 2005. To ensure stability and to minimise ore loss, the east wall has been redesigned using 700 batter angles and reduced berm width of 4m compared to 800 and 8.5 berm width of 24m bench height. The paper will also discuss how slope failures to the east wall had been sustained, managed and monitored to enhance production. Emphasis is placed on slope management at Damang which includes the principles of wall control blast, visual inspection, slope depressurisation and the state-of-the art of slope monitoring using Autoslope automated prism monitoring. Future slope monitoring is considering the use of 3D Laser and Radar to provide early warning so that evacuation could be effected. The intension is to provide mine personnel the means to identify risk areas during mining activities.

Jan 1, 2008

By J. B. A. Solar Menéndez, M. A. Martínez Fidalgo, L. A. Alvarez-Santullano

1. ANTECEDENTS This present communication refers to the results of the research project entitled "Training in the correct use of chemical oxygen self rescue apparatus and also an analysis of apparatus autonomy", carried out under the auspices of the Specific Collaboration Agreement signed between the Industry Council of the Principality of Asturias (Spain) and INSALUD (National Silicosis Institute, Spain). The antecedents of this project lie in work undertaken by the National Silicosis Institute aimed at optimising efficiency in the use of chemical oxygen self rescuers through improvements in worker training. To be precise, by means of Agreements drawn up between the above-mentioned parties, a simulator was designed and incorporated as the basis of a training station within the " Fundación Barredo" of the Industry Council of the Principality of Asturias. This has been operative since the year 2001 and, up to the present, 2300 Asturian coal mine workers have been trained there. What prompted this activity was the observation of various errors in the use of the self rescuers, deriving from their innate characteristics, especially with respect to the sensation of discomfort - the high temperature and humidity of the breathed oxygen, resistance and inconvenience - and limited autonomy. It was precisely this insight that, in critical situations, lack of familiarity with the conditions of discomfort likely to be experienced during the evacuation process might lead to rejection of the equipment, with fatal consequences, that has justified the setting up of this training and simulation centre. The centre is able to provide all mine workers with the necessary training, and experience of the characteristic sensations experienced when using such equipment (Fig.. 1).

Jan 1, 2003

By M. Ndabeni, J. H. van Vreden, M. Le Roux, Q. P. Campbell

It is not uncommon for gold slurry ponds or screen oversize dumps to contain several different types of carbon-rich contaminants. These contaminants act as robbers of dissolved gold which has a detrimental effect during the downstream carbon-in-leach (CIL) or carbon-in-pulp (CIP) processes. With a renewed interest in the reprocessing of contaminated gold waste ponds and dumps, preconcentration of the feed to either the CIL or CIP process becomes important to maximise profits from these resources. An added advantage in removing these resources, which were once thought of as being uneconomical, is the availability of land that can further be rehabilitated for community development projects. For gravity separation, an example of suitable technology is the Reflux Classifier (RC), which can be used for the separation of materials of different densities and can be used as a pre-concentration step. In this project, a laboratory-scale Reflux Classifier was used to pre-concentrate a gold-bearing sample obtained from a waste dump situated to the east of Johannesburg, South Africa. The material had an average gold grade of 1.9 g/ton and a carbon content of 10%. This material was first fed to a semi-batch Reflux Classifier that was used to fractionate it into several different density intervals by varying the fluidisation water feed rate, followed by continuous runs at fixed water flow rates. The results showed that a cumulative gold recovery of 60%, carbon recovery of 85%, and mass pull of 41% was possible for a fluidisation water feed rate of 15 L/min, while a rate of 20 L/min resulted in a gold recovery, carbon recovery and mass pull of 83%, 92% and 79% respectively, which translated into a concentrate gold grade above the set target of 3 g/ton. Continuous operation at 20 L/min yielded an underflow stream with 84% gold recovery at a grade of 5.4 g/ton. Keywords: Reflux Classification, gold recovery

Jan 1, 2020

By C. G. Verkerk

The paper discusses the transport and rheological characteristics of high concentration slurries or pastes for backfill purposes. The influence of pipe size, particle size distribution, additives, coarse material and mass concentration on these characteristics is addressed.

Jan 1, 1988

By M. Thurston

This case study shows that for a set of lognormal data with a low coefficient of variation the semi-variogram of the logs has almost the same shape as the semi-variogram of the raw data. This means that the variogram of the logs, which is numerically more stable, can be used to krige the raw data. This technique is tested on samples from a sedimentary gold deposit and the results compared to those obtained from ordinary and simple lognormal kriging.

Jan 1, 1987

By A. Yamik

This research study includes studies carried out on the recovery of unburned carbon in the ashes of Tuncbilek Thermal Power Plant. Bottom ashes have been identified by X-ray diffraction and X-ray fluorescence. These samples are potentially of class F type and have significant amounts of unburned coal. According to the ash amount that units in the thermal power plant produce, and the analyses of the samples mixed, which used certain amounts in flotation tests, it was found that the bottom ash includes 91.47% ash in dry form and 8.53% combustible matter, and the lower calorific value is 491 kcal/kg. Optimum flotation conditions to get the unburned carbon were subsequently determined by examination of the optimum flotation grain size, pulp density, collector type and amount, depressant type and amount, frother type and amount, agitation speed, and froth-taking time. While the lower calorific value of the thermal power plant bottom ashes of the 3rd , 4th and 5th units and the mixed bottom ash sample was, respectively, 959, 469, 279 and 491 kcal/kg in dry form, it increased to 2490, 1312, 786 and 1348 kcal/kg in the product obtained as a result of flotation in optimum conditions. Key words: ash, conventional flotation, unburned carbon

Jan 1, 2008

By K. Grossauer, W. Schubert

For tunnelling in poor and heterogeneous ground a reliable on-site short-term prediction is required to allow a safe and economical construction. With the use of absolute displacement monitoring data and advanced software for evaluation of the data in combination with a routine update of the geological model a considerable increase in the reliability of the short-term prediction could be achieved. The paper deals with theoretical considerations, numerical studies and case histories from alpine tunnels in heterogeneous rock. Tunnelbau in schlechtem und heterogenem Gebirge erfordert auf der Baustelle eine verlaessliche Kurzzeitprognose, um ein sicheres und wirtschaftliches Bauwerk gewaehrleisten zu können. Die Verwendung von absoluten Verschiebungsmessdaten und deren Auswertung mit Hilfe von hoch entwickelten Softwareprogrammen in Kombination mit einer laufenden Aktualisierung des Gebirgsmodells ermöglicht eine erhebliche Erhöhung der Verlässlichkeit von Kurzzeitprognosen. Dieser Beitrag beschäftigt sich mit theoretischen Ansätzen, numerischen Modellen und Fallstudien von Tunnelvortrieben in heterogenem Gebirge. La construction de tunnels dans la montagne hétérogène de faible résistance exige un pronostic fiable à court terme sur le chantier, afin de pouvoir garantir un ouvrage sûr et économique. L'utilisation des données de mesure de décalage absolues et de leur évaluation à l'aide de logiciels sophistiqués en combinaison avec une mise à jour courante du modèle de la montagne permet une augmentation considérable de la fiabilité des pronostics à court terme. Cette contribution présente des approches théoriques, des modèles numériques et de cas pratiques de progressions de tunnels dans des montagnes hétérogènes.

Jan 1, 2003

By A. Refahi

For predicting the energy consumption during the size-reduction process, the Bond approach is often used. In this work, the PFC3D discrete element method (DEM) software was employed to model the crushing behaviour of some rocks with different mechanical properties in a laboratory jaw crusher. FLAC3D software was adopted to analyze the stress distribution in the rocks. The rocks studied were modelled as granular assemblies in the shape of a sphere and/or a cube located between two jaws, and the work done by the jaws in the crusher was determined. Nine different types of rocks were studied and the energies consumed by the crusher were compared to those of the Bond comminution energy estimated from the Bond index. There is considerable difference between Bond crushing energy and work done by the jaw crusher for rocks. It appears that the Bond approach is not a suitable method for predicting single particle fracture energy done by the crusher. To verify the results obtained from DEM models, the fracture behaviour of the crushed rocks was examined and was compared to the PFC3D results. The tensile mode of fracturing is favourably modelled by the PFC3D software while the delamination mode cannot be well modelled by PFC3D software. Keywords: jaw crusher; discrete element method; crushing energy; Bond index

Jan 1, 2009

By J. H. Bulloch

A short review is given of the effects of corrosion fatigue on the materials used in pressurized water-reactor vessels. Selected topics such as testing procedures, test data, and mechanisms in simulated environments are discussed. The main fact that emerges is that most of the data on the growth of fatigue cracks reside below the ASME X1 1980 High-R 'Wet' design-code lines, Le. they fall within that specification. Finally, some recent advances in the understanding of the corrosion-fatigue behaviour of such materials in pressurized water reactors are highlighted.

Jan 1, 1987

By D. F. Malan

This paper describes the development and implementation of amine-wide continuous stability monitoring system at the Declines Section, Anglo Platinum Union JV. The Declines Section at Union JV experienced a number of large panel collapses during 2005 and 2006. As well as posing a major safety risk, the panel collapses had a major effect on production since the Declines Section is a semi-mechanized operation. The collapses would often extend into the mechanized strike roadways, resulting in a loss of access to both current and future production faces. The collapses have been largely overcome owing to a change in support design and the implementation of a mine-wide stability monitoring programme. This paper describes the precursors to collapses, which were identified using continuous closure measurements and the remedial measures taken. It also outlines the design and introduction of a robust and reliable monitoring tool, which is now used on a mine-wide basis to provide early warning of large-scale collapses.

Jan 1, 2010

By N. C. Gay

The quantitative evaluation of the performance of fill materials placed in gold mine stopes is achieved by (i) measurement of the in-situ load- displacement, or stress-strain, characteristics of the materials; (ii) an objective comparison between the observed fill performance and that predicted from suitable computer modelling techniques; and (iii) objectively comparing conditions in backfilled and conventional stopes. Considerable problems have been experienced with the development of sufficiently robust instrumentation which can be installed within filled pad- docks and give reliable information over a long period of time. However, at most mines where backfill performance is being monitored, it has been possible to correlate stress measurements within the filled paddocks with strain measurements adjacent to the paddocks. The resultant stress-strain curves agree relatively well with those determined in the laboratory. Measurements in the hangingwall strata of filled and unfilled stopes indicate that the placement of fill does reduce the amount of inelastic convergence due to bed separation. Moreover, in some stopes, the rate of convergence with respect to face advance does reduce to that of the theoretical elastic convergence. Quantification of changes in the conditions at the stope face due to placement of fill has proved difficult. Observations indicate that, provided the fill is placed close to the face (- 5 m), and adequate temporary face support is used, conditions in filled panels are superior. In addition, in filled panels the damage caused by a rockburst in the stope and, particularly, in gullies is generally much less than would be expected in an unfilled stope. To quantify these improvements, parameters such as stope height, face advance and the frequency of falls of ground are being monitored.

Jan 1, 1988

By George Kayesa

[ ] A multiple-bench slope failure occurred at Letlhakane mine on 14th July 2005. No injuries or damage to equipment was suffered and mining production was not affected. Slope failure was preceded by the precursors of tension crack formation, crack widening and extension as well as slope monitoring targets movement. It was predicted that slope failure was imminent using the Geomos slope monitoring system, though the timing was not certain. The area to be affected by the slope failure was also known before hand as was the slope failure mode. As a result, measures were taken to avoid exposing personnel and mining equipment to the slope failure risk. This paper discusses how the prediction of the slope failure of 14th July 2005 using the Geomos slope monitoring system resulted into avoiding potentially fatal injury, damage to mining equipment and loss of mining production.

Jan 1, 2006

By A. W. Sundström

This paper reviews the development and suitability of various important thermophysical and electrical properties with respect to base metal mattes. Areas of focus include the critical validation of measurements of viscosity, density, surface and interfacial tension, electrical conductivity, and an overview of the various experimental methods used to determine these properties. Accurate physical property data of mattes are critical in process modelling and computational fluid dynamic modelling of smelting and converting operations employed in the extraction of copper, nickel, cobalt and platinum group metals.

Jan 1, 2008