Search Documents

By E. J. Magri, A. Couble

Kriging estimates of geological resources are sometimes conditionally biased because the kriging plan contains too few samples. This may be done purposely in order to match the variance of the estimates to the true block dispersion variance. This work aims at evaluating the influence of conditional bias over the ultimate optimum pit design in relation to its shape, size and NPV (Net Present Value of profits). It has been restricted to two real case studies: a ‘carrot shaped’ gold porphyry in northern Greece and a manto-typeexotic copper deposit located in northern Chile. The methodology applied to each deposit consisted of generating a ‘real block model’ and four resource estimates by the use of conditional simulation and the application of four different kriging plans to the drillhole databases respectively. The estimation models vary in smoothness and conditional bias. Ultimate optimum pits were determined for the ‘real’ and the four different kriging models. Pit comparisons lead to the following conclusions: •In the worst case, conditional bias overestimated the project's NPV by 32% and 5% for the gold and copper deposits respectively. •The overestimation of high grades is more relevant than the underestimation of low grades. This resulted in a tonnage over-extraction of 148% and 1% for the gold and copper deposit respectively. This difference was attributable to the vastly different geometry of the deposits. •The smoothing effect of kriging, without or very little conditional bias, produced open pits that were different to the ‘true’ (ideal) ones and furthermore, underestimated the project's NPV by 10% and 6% for the gold and the copper deposits respectively. •Other factors that influence the optimum open pit design and to some extent control the effect of conditional bias are: the cut-off grade, the orebody geometry and distribution of grades within it and the amount of over-burden. Keywords: conditional bias, ultimate pit design

Jan 1, 2003

By P. N. Erasmus

This paper considers the fundamental concepts of support design for underground openings in highly stressed ground. It concludes that the conventional deformed reinforcing bar, woven mesh and cable lacing support methods that have been widely used in deep gold mines are quite in appropriate for the support of highly stressed tunnels. The following is suggested as the criterion for adequate dynamic support under rockburst conditions: the energy absorbed by a support unit (yielding through some acceptable limited displacement) should exceed the kinetic energy generated by the mass of rock that is intended to be retained by that unit. Duraset in conjunction with SRK Consulting has developed a yieldable steel tendon called the Durabar®. It is unique in the sense that it cleverly utilizes the property of the ductility of ordinary low-carbon steel from which it is made to accommodate the excessive displacement it is subjected to in the case of rockbursts or swelling ground.

Jan 1, 2009

By L. Capponi

At Tapira Mine (Tapira/MG/ Brazil), the largest phosphate concentrate producer in Brazil, the mining is fully mechanized and carried out using open pit mining. This work presents a review of the sampling protocol used for short term mine planning at different stages. Sampling is carried out in two steps. Firstly, diamond drill cores are sampled at 50 x50 x5 metre pattern. Fosfertil analyses grades of P2O5, Fe2O3, CaO, MgO, SiO2 and TiO2 plus geological logging. This information feeds the long term block model. Secondly, drill cuttings are collected at the mining faces released for blasting. The drilling pattern is staggered and when blasting is not necessary, a drill hole is made centered in the block area (25 x 25 x 5 m). The primary samples have mass approximately 60 kg and the same chemical parameters are analysed. Metallurgical and mass recovery tests are performed as well. These samples are used to build the short term block model. At the final stage, the short term mine planning model is used to build a stockpile blending model which is simulated using a spreadsheet to match the goals established by the process plant.

Jan 1, 2009

By R. J. Cocks

Water auditing and water efficient practices are evolving as the quantitative tools for water balance reporting in the mining and minerals processing sector. This paper was written to describe the process of water auditing in a gold mining environment. It will contribute towards building an appropriate water management framework for The Cooperative Research Centre (CRC) for sustainable resource processing (CSRP). The research assists with the assessment of water balances in mining and hydrometallurgical processes and provides, on the ground, steady-state data for ongoing probabilistic modeling underway at most of Newmont?s gold mine operations. Five Newmont case study mine sites including the Tanami Granites Goldmine are central to this PhD water project study. The function of the Tanami-Granites water audit exercise was to measure a controlled flow of various water quality types and set a framework to establish further research for water efficiencies and water conservation in mining.

Jan 1, 2009

"Chairman: Dr N. G. W. Cook Rapporteur: Mr M. P. RobertsPapers:Planning open pit mining operations using simulation by A. Bauer and P. N. Calder Simulation for control of underground liquid flow by G. N. Pitts and P. B. CrawfordEvaluation of production strategies in a group of copper mines by linear programming by P. H. Williams, J. N. Brooke and D. M. PoulterAn equipment maintenance system by D. W. Dean and J. A. RyderTaken as a whole, the difference between the four papers in this session were perhaps more illuminating than their similarities. The titles of the first and second papers contained the word 'simulation', and in both papers random number generation was relied upon in the selection of inputs from empirical distributions, but the nature of the models to which these values were inputs were quite different. The third paper displayed another method of uniting the empirical and the theoretical in a linear programming formulation whose matrix coefficients were measured empirically, and here some apt remarks on computer implementation were included. This paved the way for the last paper which abandoned all theoretical pretensions in favour of a detailed description of computer implementation and perhaps as a result gave rise to the most feeling audience participation.The systems mentioned were developed for the iron, petrol, copper and gold producing industries in the US, Canada, Zambia and South Africa..As with all the parallel sessions, contributions from the floor may have been limited by the shorter time available to delegates to acquaint themselves with the papers before the session. In spite of this, and due largely to the active chairman¬ship of Dr Cook, the discussion during the session which is summarized here contributed much to the information contained in the papers themselves.In his presentation, Dr Calder summarized his paper. He expected that simulation would be used in future on an almost universal basis in open pit mining. It could contribute new knowledge more cheaply than experimentation in the flea For example, this study had shown what was previously thought to be a matter of more shovels and trucks was really a blasting problem, and improving blasting had increased production to the desired level. The simulation had shown that uniformity of truck performance was a desirable factor. It had also been used to study the advisability of a dispatching system.Dr Ramani contended that where equipment characteristics were available, deterministic standard simulation could adequately simulate systems in which interference occurred. Operator performance could be measured against perfor¬mance curves predicted by standard simulation and poor operators spotted and retrained. The present system did not take into account variability in truck loading, for instance. Dr Calder replied that if the number of variables was large, the standard approach became too complicated for operating personnel to follow. He admitted he had not tried it. The variability of truck loading could be coped with easily using the Monte Carlo approach. Operator variability was already incorporated because the time studies are actual."

Jan 1, 2014

By S. R. Stadler

Koffiefontein Mine commissioned a distributed antenna system as an underground communication backbone for the DISPATCH® production management system during September1999. STAS Ltd, the supplier of the Distributed Antenna System developed the System for an Integrated and Automated Mine (SIAM). This communication system, in conjunction with DISPATCH®, fulfils Koffiefontein Mine’s present and future requirements for accurate draw control, increasing productivity and improving working conditions. The DAS as SIAMnet communication network was selected by the mine, because of its superior data transmission rate of up to 1.5Mbps at 860MHz, video and Ethernet transmission facilities, and future enhancement abilities. The results of the commissioning tests confirmed the quality and integrity of the data and voice communication. The initial installation enabled 9000 metres of underground production tunnels with voice communication inclusive of 3700 metres having data communication. This article discusses the requirements and selection of the telecommunication system for an underground mine. A description of the installed distributed antenna system follows with a summary of the commissioning tests. A discussion of the reliability of the components is followed by conclusions with suitable recommendations. Keywords: distributed antenna system, underground mining, telecommunication system.

Sep 1, 2001

By P. Lundman, L. Rosengren, T. Brandshaug

Tunnel 99’, the Swedish National Road Administration´s (SNRA) general technical specification for road tunnels requires that the load bearing system must be designed to withstand specified design explosion loads. This paper presents the results of an SNRA study to provide a perspective of design analyses tailored to comply with the new requirement. The paper provides an example of a design analysis for assumed tunnel conditions using a numerical model. Dynamic predictions of potential damage to the rock mass and ground support system (rock bolts and shotcrete) from the specified explosion loads are presented including the nonlinear response of the shotcrete. “Tunnel 99”, qui fixe les règles de l’Administration nationale suédoise des Routes (Vägverket) concernant la conception et la construction des tunnels routiers, requiert entre autres que la structure porteuse soit capable de résister à certaines contraintes spécifiques résultant d’explosions. Cette étude présente les résultats d’une étude effectuée par Vägverket en vue d’obtenir une perspective d’analyses de conception spécialement élaborées pour se conformer aux nouvelles règles. Il contient un exemple d’analyse en fonction de conditions déterminées, basée sur un modèle numérique. Des prévisions de’études dynamiques de dommages potentiels subis par la masse rocheuse et les systèmes de soutènement (boulons d’ancrage et béton projeté) du fait des contraintes libérées par la force d’explosion spécifiée sont également présentées, y compris dans le cas d’une réaction non linéaire du revêtement en béton. “Tunnel 99” - die Vorschriften für Strassentunnel der Nationalen Schwedischen Behörde für Straßenwesen - (Vägverket) - fordern vom Tragsystem eine Auslegung in der Form, dass es spezifischen Explosionsbelastungen standhält. Dieser Artikel präsentiert die Ergebnisse einer Studie der Behörde, um einen Ausblick über konstruktive Auslegungen zu geben, die geeignet sind, die neuen Vorschriften zu erfüllen. Der Artikel zeigt ein Beispiel einer konstruktive Auslegung für eine angenommene Tunnelsituation mit Hilfe eines numerischen Modells. Voraussagen unter Beachtung der vollständigen dynamischen Berechnung zu potentiellen Schädigungen des Gebirges und des Ausbaus (Anker und Spritzbetonauskleidung) durch die spezifizierten Explosionsbelastungen, einschließlich des nichtlinearen Verhaltens der Spritzbetonauskleidung, werden gezeigt.

Jan 1, 2003

United Kingdom mineral statistics 1977. Home, D., Squirrell, H. C., and Venkatesan, J. (compilers). London, Her Majesty's Stationery Office, 1978. 156 pp. £10,25. Copper mining and management. Navin, Thomas R. University of Arizona Press, Box 3398, Tucson, Arizona 85722. ISBN 0-8165-0586-1. 426 pp. Illustrated. Price Metal statistics 1967-1977. 65th edition. 1978. Metallgesellschaft AG, Reuterweg 14, D 6000 Frankfurt am Main, Fed. Rep. of Germany. 382 pp. Illustrated. Coal mine ground control. Peng, Syd S. John Wiley & Sons. ISBN 0-471-04121-1. 450 pp. Illustrated. £19.75 clothbound. Associate Professor and Chairman of the Uranium supply and demand: Proceedings International Symposium, London, July 1978. Spriggs, Michael J. and Casteel, Kyran D. (editors). Mining Journal Gemorfologiesewoordelys/Geomorpho logical vocabulary. Van der Merwe, J. S., en De Villiers, A. B. (samestellers).

Jan 1, 1979

By J. C. M. De Souza

The Samarco pipeline, the longest in the world for iron ore slurry transportation, started operation in 1977 to transport concentrate from the Germano facilities, in the state of Minas Gerais, to the pelletizing plant, located 396 km away, in the state of Espirito Santo, on the south-east coast of Brazil. Designed for a nominal capacity of 12 million tons per year, the pipeline reached 15.5 million/year due to operational improvement and, in late 2005, it was resized to transport 16.5 million tons per year, with the installation of a booster station. In order to ensure the accurate performance of the system, a pipeline cleaning programme was carried out and, since it has been29 years from the operation start-up, precise knowledge of the pipe condition would be fundamental to guarantee the success of the project. The cleaning programme demonstrated the potential of operational gains from this initiative, and its effect on the corrosion control and future measures, which should be permanently adopted to maintain the improved capacity. The intelligent pig runs provided essential data used to establish a pipeline integrity programme that allowed Samarco to develop a pipe repair plan based on the severity and significance of the features and to implement a future pipe replacement plan.

Jan 1, 2007

By T. Feroze, B. Genc

"Blind headings in room and pillar coal mines are a major source of methane and coal dust. Most methane and coal dust explosions therefore occur in the blind headings. The primary cause of these explosions is the disruption of the local ventilation system. Line brattice (LB) ventilation systems are used to ventilate blind headings by directing air from the last through road (LTR) into the heading. The amount of air available to ventilate the face of the empty heading depends on the heading dimension, settings of the LB, and velocity of air in the LTR. LBs are commonly installed by underground supervisory staff based on work experience, which may result in ineffective ventilation. The correct installationof LBs remains a challenge. In this study, a validated computational fluid dynamics (CFD) model has been used to analyse the effect of the LB ventilation system variables on the air flow rates close to the face of the empty heading. Full-scale three-dimensional models with various heading heights, heading depths, LB settings, and LTR velocities were simulated. The air flow rates and patterns at various locations inside the heading were analysed. A comparative study was carried out to quantify the effect of each of these system variables on the flow rates close to the face of the heading. Based on the findings, a user-friendly numerical model was formulated that can be used to estimate the flow rate close to the face of an empty heading for different practical settings of the system variables. This model can help the supervisory staff to swiftly implement the ventilation plan according to the regulations and the mine standards. The model can also serve as part of the curriculum for educating future mining engineers."

Jan 1, 2017

By T. Feroze, B. Genc

"Blind headings in room and pillar coal mines are a major source of methane and coal dust. Most methane and coal dust explosions therefore occur in the blind headings. The primary cause of these explosions is the disruption of the local ventilation system. Line brattice (LB) ventilation systems are used to ventilate blind headings by directing air from the last through road (LTR) into the heading. The amount of air available to ventilate the face of the empty heading depends on the heading dimension, settings of the LB, and velocity of air in the LTR. LBs are commonly installed by underground supervisory staff based on work experience, which may result in ineffective ventilation. The correct installation of LBs remains a challenge.In this study, a validated computational fluid dynamics (CFD) model has been used to analyse the effect of the LB ventilation system variables on the air flow rates close to the face of the empty heading. Full-scale three-dimensional models with various heading heights, heading depths, LB settings, and LTR velocities were simulated. The air flow rates and patterns at various locations inside the heading were analysed. A comparative study was carried out to quantify the effect of each of these system variables on the flow rates close to the face of the heading. Based on the findings, a user-friendly numerical model was formulated that can be used to estimate the flow rate close to the face of an empty heading for different practical settings of the system variables. This model can help the supervisory staff to swiftly implement the ventilation plan according to the regulations and the mine standards. The model can also serve as part of the curriculum for educating future mining engineers."

Jan 1, 2017

By A. S. Macfarlane

Western Deep Levels (North) is a deeplevel, longwall gold mine. Severe strata control problems and high rates of elastic closure, resulting in high rates of energy release, are associated with mining at depths of up to 3 500 metres. To assist in controlling these aspects of mine design and safety, a waste backfilling system has been designed and commissioned. The integration of such a system into an existing, producing longwall brings many problems of logistics, organization, planning and control. It is the purpose of this paper to examine these aspects of fill management, and to describe some of the practical problems involved with the integration of this project into the mining environment. Although many of the rock mechanics and soil mechanics aspects of backfilling systems are common there are specific problems involved which apply to longwall systems. Very strict guidelines are required for planning personnel to design their backfilling systems for a particular situation. These aspects are examined, and basic models developed which can be used without the necessity of comprehensive input from rock mechanics. A summary of the financial implications is included, and these are examined with regard to possible future applications and expansion of waste filling.

Jan 1, 1988

One of the most critical and complicated steps in mine design is a suitable mining method selection based upon geological, geotechnical, geographical and economical parameters. Since there are many factors involved in mining method selection, the decision-making process is very difficult. In this paper, the Analytical Hierarchy Process, with 13 criteria, is used to develop a suitable mining method for the Golbini No. 8 deposit in Jajarm (Iran). Six alternatives (conventional cut and fill, mechanized cut and fill, shrinkage stoping, sublevel stoping, bench mining, and stull stoping) are evaluated. The studies show that the suitable mining method for this deposit in the present situation is the conventional cut and fill method.

Jan 1, 2008

By T. Feroze, B. Genc

"The ventilation of underground coal mines plays an important role in minimizing the risk of methane and coal dust explosions. The ability of ventilation, with the use of line brattices (LBs), to remove methane and coal dust in empty headings is dependent on the amount of air leaving the LB and entering the heading. The quantity of this air depends on the associated system variables, namely heading dimensions, settings of the LB, and velocity of air in the last through road (LTR). However, the exact effect of these system variables on the flow rate at the exit of the LB in an empty heading is not known. The installation of LBs in South African coal mines is generally carried out based on experience. This can result in overor under-ventilation and may increase the cost of providing ventilation or cause accidents, respectively. In this paper, using computational fluid dynamics (CFD), the air flow rate at the exit of the LB in an empty heading was estimated using full-scale three-dimensional models. The CFD model used was validated using experimental results Firstly, the settings of these three system variables were varied, the flow rates at the exit of the LB were measured, and finally the results were used to calculate the effect of each system variable. The outcome is a mathematical formula that can be used to estimate air flow rate at the exit of the LB in empty headings for any practical scenario.This paper will help the coal mining sector in South Africa by providing estimation models based on scientific reasoning for the installation of LBs, and will also serve academia as part of the curriculum towards educating future mining engineers."

Jan 1, 2016

By H. Moslemi

Metal sulphides are usually semiconductor and their electrical conductivity is low; therefore they are sources of electrons and promote electrochemical reactions. This phenomenon is of significant importance in sulphide flotation. The formation of a hydrophobic surface on the sulphide minerals is the result of various electrochemical reactions. Potential difference in the mineral-liquid interface plays an important role in the kinetics of the reactions, and consequently, on the flotation behaviour of sulphides. The value of the potential difference is influenced by different oxidation-reduction reactions at the interface area, and is measured by a two-electrode system in which an electrode is applied as reference electrode. In this study, we attempted to measure open-circuit potentials of pyrite, pyrrhotite, and steel electrodes with respect to the reference electrode. To verify the results, two reference electrodes, saturated calomel and gold, were used. Time-potential relations with respect to both reference electrodes show that the potential of both pyrite and pyrrhotite increases with time; however, this trend decreases for steel except when at pH 12. The results show a potential drop by an increase in pH value, except for steel, for which the opposite holds. This paper discusses galvanic interactions between minerals and grinding media in the grinding circuits, as well as among other minerals in the flotation processes.

Jan 1, 2012

By S. Kahraman

The prediction of rock properties from indirect testing methods is important, particularly for preliminary investigations since indirect tests are easier and cheaper than the direct tests. In this study, we investigate the predictability of the uniaxial compressive strength (UCS) and Brazilian tensile strength (BTS) of rocks from the indentation hardness index (IHI) obtained using point load apparatus. Forty-six different rock types, 14 of which were igneous, 15 were metamorphic, and 17 were sedimentary were tested in the laboratory. The UCS and BTS values were correlated with the corresponding IHI values and the results were statistically analysed. The influence of rock classes on the relationships was also investigated. A strong correlation between UCS and IHI was found for all data. The correlation between BTS and IHI is not as strong as the correlation between UCS and IHI, However, it is in the acceptable limits. When the regression analyses were repeated for igneous, metamorphic, and sedimentary rocks, the correlation coefficients were generally increased. The results show the UCS and BTS can be estimated from IHI, In addition, the effect of rock classes on the relationships between IHI and both UCS and BTS is important.

Jan 1, 2012

By J. Zwartendyk, A. Azis

"Every nation must decide how it should exploit its mineral resources so as to contribute most to its national objectives. It is argued that the present value of the future corporate income tax flow derived from mineral exploitation may serve as a useful indicator in moving toward a taxation policy that would contribute optimally toward the greatest public benefit.The future stream of corporate income taxes depends largely on the mineral endowment, consisting of deposits now being mined, known unmined deposits, and unknown deposits.Unknown deposits may be estimated by geological inference. Both known and unknown deposits can be categorized according to grade and size, and divided into economic and uneconomic deposits on the basis of certain prices, costs, rate of return and taxation levels.Computer simulations can be run of discounted cash flow models at various taxation levels to show the impact of taxation changes on future tax revenues."

Jan 1, 2014

By A. O. Filmer

In the mining and metals industry, business strategy demands that leaders extract more from any set of capital assets. This improvement is achieved through a combination of continuous improvement and upgrading of the assets. Continuous Improvement involves a series of incremental changes in the workplace to stabilize the process, remove waste, and test the limits of process capability. Enhanced Technology involves the replacement of an existing as set with a different process or equipment, to achieve a similar function in a more efficient and effective manner. The paper compares and contrasts the two methodologies and outlines the key business considerations which dictate how and when to select one or other improvement method. The paper also addresses the implications for these two improvement methods for those undertaking R&D in support of the mining and metals business.

Jan 1, 2009

By C. G. Carey, M. P. Mullins

BHPBilliton is a large (US$32bn market capitalization) diversified mining group. Significant organic growth is planned through the development of a number of mining, processing and oil and gas projects, totalling some US$5.2bn over the next three years. The investment standards underpin the capital approval process, and incorporate the requirements for range and risk analysis of key input variables, including mineral resources. Public reporting codes for mineral resources and ore reserves (such as JORC) stipulate deterministic reporting of estimates, but are generally silent on any requirement for range or risk assessment, although they acknowledge the risk and uncertainty in the production of resource estimates. In contrast, public reporting of petroleum reserves allow for the use of either deterministic or probabilistic estimation, and for the latter, mandate the level of confidence required for proven versus probable reserves. Conditional simulation techniques, popular in the petroleum industry, provide an ideal tool forrange and risk assessment of the range of outcomes of key resource parameters, such as tonnagesand grades. Examples of a diamond deposit and of a porphyry copper deposit are presented. The understanding and quantification of mineral resource risk through a technique such as conditional simulation provides quantified information on the potential upside or downside. These techniques should be more widely utilized in the high-risk minerals extraction industry. Keywords: mineral resources, conditional simulation, risk, capital investment standards, BHPBilliton.

Jan 1, 2003

By JOURNAL SAIMM

SYMPOSIUM ON PELLETS AND GRANULES During October 1974, the Newcastle branch of the Australasian Institute of Mining and Metallurgy is to hold a symposium on pelletizing and granulation, with particular reference to the iron ore, fertilizer, and cement industries.

Jan 12, 1973