Search Documents

By J. E. Dickinson, J. L. Sutherland, J. Zhou, M. J. Cole, K. P. Galvin

Interest in early gangue rejection has grown substantially in the minerals industry to reduce energy and water consumption arising from excessive comminution. Recent developments in coarse-particle flotation have proven successful by promoting a quiescent hydrodynamic environment to limit particlebubble detachment and by helping to convey more buoyant particles to the overflow. Current approaches also benefit from upstream classification to remove the finer particles ahead of the coarse-particle flotation. In this study, coarse-particle flotation was investigated experimentally using a novel hybrid gravity-flotation system called CoarseAIR™ that exploits the hydrodynamic advantages of the Reflux® Classifier. The system consists of a lower fluidised bed housing, with a system of inclined channels above. The inclined channels enhance the segregation and hence rejection of intermediate through to relatively coarse particles containing little or no surface liberation. This approach overcomes the need for pre-classification, while offering strong transport of coarse particles made buoyant through their attachment to air bubbles. The paper explores the strong relationship between the solids transport to the overflow and the input gas flux, showing firstly the potential for significant mass rejection at the relatively low gas fluxes, and robust performance in terms of recovery across the full range of gas fluxes. Keywords: Flotation, inclined channels, coarse particle flotation, Reflux Classifier

Jan 1, 2020

The kinetics of adsorption of gold di-cyanide onto activated carbon has been investigated extensively over the past two decades. These studies have demonstrated that both film and intra-particle mass transfer affect the kinetics. The dominant mechanism of intra-particle mass transfer has not yet been identified. In the work described, surface diffusion and pore diffusion are considered as possible rate-determining mechanisms of intra-particle mass transfer. Mathematical models are described that incorporate film mass transfer and the respective intra-particle mass transfer mechanism with equilibrium described by a Freundlich isotherm. Rate constants of film mass transfer and pore or surface diffusivities were estimated by the fitting of the respective models to experimental carbon adsorption data. The estimated pore diffusivities, after they had been corrected for the porosity and tortuosity of the carbon, were found in most instances to be higher than the molecular diffusivity of dilute gold di-cyanide in aqueous solution. This situation is not physically viable. The surface diffusion mechanism acting in parallel with the pore-diffusion mechanism is thus responsible for the intra-particle transportation of most of the gold.

Jan 1, 1996

By S. J. Bluhm

Recommendations are given for the design of multi-stage spray chambers in which air flows horizontally through water sprays. A detailed description is given of one such spray chamber at Hartebeestfontein gold mine that is used for bulk cooling of the incoming ventilation air, and that has been constructed according to these recommendations. A method for predicting the performance parameters of horizontal multi-stage spray chambers is given, and the method is illustrated with some examples. The method is equally applicable to spray chambers in which the water, rather than the air, is cooled.

Jan 1, 1979

By P. W. Ocerbeek

The occurrence, properties, and uses of andalusite, and its advantages over other refractory minerals and materials, are discussed. Ore reserves are given for the five producing areas, and statistics on production, export sales, and prices are included to illustrate the growth of the industry since the early 1960s. The mining and beneficiation procedures are described, with special reference to new techniques in concentration and magnetic separation. As fines dumps represent a considerable source of andalusite, possible methods of recovery are discussed. . The outlook for the future appears favourable, and possible competition from other sources and substitute refractory minerals are mentioned. It is concluded that the industry is in a sound position to maintain South Africa's status as the world's foremost producer and supplier of andalusite.

Jan 1, 1989

The mining rock-mass rating (MAMA) classification system was introduced in 1974 as a development of the CSIA geomechanics classification system to cater for diverse mining situations. The fundamental difference was the recognition that in situ rock-mass ratings (AMA) had to be adjusted according to the mining environment so that the final ratings (MAMA) could be used for mine design. The adjustment parameters are weathering, mining-induced stresses, joint orientation, and blasting effects. It is also possible to use the ratings (AMA) in the determination of empirical rock-mass strength (AMS) and then in the application of the adjustments to arrive at a design rock-mass strength (DAMS). This classification system is versatile, and the rock-mass rating (AMA), the mining rock-mass rating (MAMA), and the design rock-mass strength (DAMS) provide good guidelines for the purposes of mine design. However, in some cases a more detailed investigation may be required, in which case greater attention is paid to specific parameters of the system. Narrow and weak geological features that are continuous within and beyond the stope or pillar must be identified and rated separately. The paper describes the procedure required to arrive at the ratings, and presents practical examples of the application of the system to mine design.

Jan 1, 1990

By F. H. Deist, J. P. E. Morris, E. Georgiadis

For some years the Collieries Research Laboratory of the Chamber of Mines of South Africa has been engaged in the development and application of computer programmes to aid in the solution of rock mechanics problems. It is the purpose of this paper to introduce some of the programmes having general applicability. A system capable of predicting stresses and displacements induced by large-scale tabular excavations is discussed. A finite element programme especially designed for handling layered continuum problems, and which is being used extensively has been supplemented by an automatic mesh generation facility that reduces problem preparation times considerably. Some typical applications of these programmes are described. An entirely new approach, potentially capable of performing linear three-dimensional continuum analysis at practical cost is introduced.

By R. S. Sarracino, M. J. Louw, S. M. Vather

Two detonation models, IDeX for ideal VOD and CPeX for non-ideal VOD, were used to predict the velocities of detonation (VOD) of five explosives: ANFO, a bulk emulsion, and three repumpable emulsions (R100 Gold, R100 Diamond, and R105). The theoretical VODs were compared with the in-hole VODs of the explosives, and the predicted and actual values were found to be within experimental error for ANFO and the bulk emulsion. The results were not consistent for the repumpable emulsions. The discrepancies can be explained as being due to variations in mining and loading practices. The results show that the detonation models can be effective tools in predicting the behaviour of explosives in different diameters and rock confinements, provided that the user is aware of the factors that can affect the optimal usage of explosives and equipment.

Jan 1, 1993

By J. E. Forbes, B. K. Loveday

The role of gravity concentration in the recovery of gold from typical South African gold ores is described. The location of the concentrator in the grinding circuit is discussed, and typical capacities and operating costs are given. Some operating problems are mentioned, but the performance of concentrating equipment is not dealt with in detail since this to some extent depends on the nature of the ore. It is concluded that the main benefits are an improved recovery of coarse gold and a reduction in soluble loss. The use of a long leaching time and a carbon-in-pulp recovery system may eliminate the need for gravity concentration. but gravity concentration is seen as an inexpensive way of improving the recovery on existing plants.

Jan 1, 1982

By J. Keyser

The realization of an Integrated Technical Resource Asset Management System (ITRAMS) has so far evaded all software developers in the mining industry. The major factors that have prevented the development of such a system are limitations on software, hardware and network systems. Several factors have come together at Venetia Mine, which has made the undertaking of such a project both possible and desirable. This has led to the formation of a strategic partnership between Venetia Mine and Gemcom Software International Inc. This partnership is dedicated to develop and provide an Integrated Technical Resource Asset Management System based on Microsoft Back Office architecture, Gemcom for Windows™ and the MinRas system. This paper will elaborate on the phased approach of the integration of systems into the core repository, mechanisms of integration, the functionality of the system, final results, techno-economic benefits and general project management issues.

Sep 1, 2001

By R. G. B. Pickering, H. H. Haase

Few innovations in the South African gold mining industry could have a more significant impact on improving profitability than non-explosive methods of mining. The far-reaching benefits of this approach are explained and the progress made through development work funded by the industry is described. Three methods are considered: impact ripping, sloting with abrasive waterjets and diamond saws, and breaking from drilled holes with waterguns and electric pulses. Of these methods, impact ripping is the most advanced and requires only minor refinements before production applications can be initiated. Although this method, based on current performance, is expected to yield considerably increased profits, it is predicted that it could perform several times better than at present with further development. The other methods of rockbreaking also show potential. Waterguns and electric rockbreaking would be attractive in unfractured rock for difficult geological conditions, and for confined areas such as gullies and development ends. Methods based on sloting could be combined with any of the other methods to enhance their effectiveness and thus yield further improvements in profitability; also, they could be used to advantage in specific applications. Al the discussed methods, therefore, deserve to be developed further.

Jan 1, 1991

By A. Kapito

The ferrite-pearlite microstructure is the most popular microstructure for alloys used in structural applications, including railway wagon wheels. These alloys have been designed through alloying and thermo-mechanical processing to have a refined microstructure. Ferrite-pearlite alloys are low cost, weldable, have good fabricability, and are reliable under extreme conditions. Given these performance attributes, it seems unlikely then that their dominant position as structural steels would ever be challenged by alternative microstructures. One major achievement in the development of ferrite-pearlite steels has been in the refinement of their interlamellar spacing to very fine distances of the order of < 0.3 µm. A refined microstructure increases the hardness of the alloy, thus increasing its life under wear conditions. The interlamellar spacing in pearlitic steels has, however, been refined almost to its theoretical limit. The increasing demand for speed and increased axle loading on railway wagons requires the use of stronger, tougher, and more durable materials. This has opened the window for the development of novel bainitic steels. Bainitic alloys have a higher level of microstructural refinement than pearlitic ones. They have shown to have good wear resistance and rolling-contact fatigue resistance, and high toughness. This paper will discuss the progress to date on the development of bainitic railway wheel alloys. Four alloy chemistries have been chosen for possible further development.

Jan 1, 2012

By R. J. Davidson

The chemistry related to the adsorption of gold, uranium, and transition-metal ions onto algal biomass (activated carbon) is related to the genesis of the Witwatersrand. Detrital gold being washed into the early basin, together with cyanide generated in the atmosphere, would have solubilized as the stable aurocyanide complex, the necessary oxygen being produced from the photosynthesis of carbon dioxide by primitive algae. Pebble-type conglomerates, while providing for the free movement of solutions containing the vital nutrients for prolific algal growth, would have screened of the sunlight, which would otherwise have degraded any free cyanide in solution. With the subsequent decomposition of the algal deposits, it is surmised that carbon-rich layers having adsorptive properties similar to those of activated carbon formed in the conglomerates. Under these conditions, gold (silver) in solution would have been adsorbed selectively as the cyanide complex, together with uranium as the carbonate complex. Any transition-metal ions present would also have been adsorbed onto such a substrate. The subsequent burial and compression of the gold-rich conglomerate with temperatures rising to about 400DC would then have reduced the adsorbed gold to the metal in a single segregated gold-silver metal phase (95 to 99 per cent of the contained gold), while leaving behind a sulphide phase rich in iron, base metals, and arsenic and containing some gold and silver. The recrystalization of this later phase may explain the presence of the rather consistent contents of secondary pyrite in the Witwatersrand conglomerates. Similarly, uranium minerals, some rich in titanium and carbon, may also have formed. An adsorption model would explain the very consistent trends in the gold-to-silver ratios of individual reefs in the Witwatersrand, which suggest an extensive hydrothermal system approaching isothermal equilibrium. Also, as gold grades increase, so silver grades generally decrease, indicating the sequential displacement of silver by gold as classically obtained with activated carbon.

Jan 1, 1990

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. All papers must meet the standards set by the Council of the Institute, and for this purpose all papers are referred to at least two referees appointed by Council. STANDARDS FOR ACCEPTANCE To merit consideration papers should conform to the high standards which have been established for publication over many years. Papers on research should contain matter that is new, interpretations that are novel or of new significance and conclusions that cast a fresh light on old ideas. Descriptive papers should not be a repetition of well-known practices or ideas but should incorporate developments which would be of real interest to technical men and of benefit to the mining and metallurgical Industry. In some cases a well prepared review paper can be of value, and will be considered for publication. All papers and particularly research papers, no matter how technical the subject, should be written with the average reader of the Journal in mind, to ensure wide interest. The amount of textbook material included in a contribution should be the minimum essential to the argument. The length of a paper is not the criterion of its worth and it should be as brief and concise as possible, consistent with the lucid presentation of the subject. Only in very exceptional circumstances should a paper exceed 15 pages of the Journal (15 000 words, if there are no tables or diagrams). Six to ten pages is more normal. NOTE: Papers in the Journal are printed in 10 point type, which is larger than the 8 point type used on this page. For special publications Council may decide on page sizes smaller than A4 used for this Journal. The text should be typewritten, double-spaced, on one side only on A4 size paper, leaving a left-hand margin of 4 cm, and should be submitted in duplicate to facilitate the work of the referees and editors. LAYOUT AND STYLE Orthodox sequence Title and author&apos;s name, with author&apos;s degrees, titles, position. Synopsis. Index, only if paper is long and involved. Introduction, including a brief statement of conclusions. Development of the main substance. Conclusions. in more detail. Acknowledgements. References. Title: This should be as brief as possible, yet give a good idea of the subject and character of the paper. Style: Writing should conform to certain prescribed standards. The Institute is guided in its requirements by: Collins, F. H., Authors & Printers&apos; Dictionary-Oxford University Press. Hart, H. Rules for Compositors and Readers. Humphrey Milford (familiarly known as the Oxford Rules). Fowler, H. W. & F. G. The King&apos;s English-Oxford University Press. General: A few well selected diagrams and illustrations are often more pertinent that an amorphous mass of text. Over-statement and dogmatism are jarring and have no place in technical writing. Avoid the use of the first person, be objective and do not include irrelevant or extraneous matter. Avoid unnecessary use of capitals and hyphens, while punctuation should be used sparingly and be governed by the needs of sense and diction. Sentences should be short, uninvolved and unambiguous. Paragraphs should also be short and serve to separate basic ideas into compact groups. Quotation marks should be of the &apos;single&apos; type for quotations and "double" for quoted matter within quotations. Interpretations in the text should be marked off by parentheses ( ), whereas brackets [ ] are employed to enclose explanatory matter in the text. Words to be printed in italics should be underlined singly. For small capitals they are to be underlined DOUBLY and for large capitals TREBLY. If there is any problem in producing formulae accurately by typewriter they should be inserted by handwriting in ink in the copy forwarded by authors. Abbreviations and symbols are laid down in British Standard 1991. Abbreviations are the same for the singular and plural, e.g. cm for centimetre and centimetres, kg for kilogram and kilograms. Percentages are written in the text as per cent; the symbol % is restricted to tables. A full stop after an abbreviation is only used if there is likely to be confusion of meaning. Metric System: The Systeme International d&apos;Unites (S.I.) is to be used for expressing quantities. This is a coherent system of metric units derived from six basic units (metre, kilogramme, second, ampere, kelvin, and candela), from which are derived all other units, e.g. the unit of force is the newton (N) for kilogramme metre per second per second (kg m/s2). Always use the standard metric abbreviations. Commas must not be used for separating groups of digits. For ease of reading digits should be grouped in threes counting from the decimal point towards the left and the right. Illustrations: Drawings and diagrams are to be in black India ink and should be about 18 cm wide. When submitting graphical representations avoid a fine grid if possible. Curves should be in heavy line to stand out. Lettering too should be bold as a reduction in size is often involved in the printing process. (A single column is 8.5 cm wide.) Numbering of tables should be in Roman numerals: I, 11, etc. and figures in Arabic numerals: Fig. 1, Fig. 2, etc. (Always use the abbreviation for figure.) Photographs should be black and white glossy prints. As a guide to the printer the author should indicate by means of notes in the typescript where tables and figures, etc. are to appear in the text. Paragraphs: A decimal system of numbering paragraphs may be used when the paper is long and complicated and there is a need for frequent reference to other parts of the paper. Proof correction: Galley proofs are sent to authors for the correction of printers&apos; errors and not for the purpose of making alterations and additions which may be expensive. Should an author make alterations which are considered excessive, he may be required to pay for them. Standard symbols as laid down in British Standard 1219C should be used. SYNOPSIS It is most important that the synopsis should provide a clear outline of the contents of the paper, the results obtained and the author&apos;s conclusions. It should be written concisely and in normal rather than abbreviated English and should not exceed 250 words. While the emphasis is on brevity this should not be laboured to the extent of leaving out important matter or impairing intelligibility. Summaries simplify the task of abstractors and therefore should present a balanced and complete picture. It is preferable to use standard rather than proprietary terms. FOOTNOTES AND REFERENCES Footnotes should be used only when they are indispensable. In the typescript they should appear immediately below the line to which they refer and not at the foot of the page. References should be indicated by super-script, thus. . .1 . . .2. Do not use the word Bibliography. When authors cite publications of other societies or technical and trade journals, titles should be abbreviated in accordance with the standards adopted by this Journal. GENERAL The Council will consider the publicatiol1 of technical notes taking up to three pages (maximum 3000 words). Written contributions are invited to the discussion of all papers published in the Journal. The editors, however, are empowered by the Council to edit all contributions. Once a paper or a note has been submitted to the Institute, that document becomes the property of the Institute, which then holds the copyright when it is published. The Institute asa body is, however, not responsible for the statements made or opinions expressed in any of its publications. Reproduction from the Journal is permitted provided there is full acknowledgement of the source. These points should be borne in mind by authors who may submit their work to other organizations as well as to the Institute. P.W.J.vR.

By H. W. J. P. Neomagus, J. R. Bunt, T. S. Mthombo, C. A. Strydom

"Low-cost calcium lignosulphonate (CL), which is a byproduct of the wood pulping industry, was investigated as a potential binder during laboratoryscale pelletization of inertinite-rich high-ash coal fines from the Highveld Coalfield of South Africa. Coal-binder mixtures containing between 1 and 15% calcium lignosulphonate were prepared, pressed, and ultimate, proximate, porosity, XRD, and XRF analyses obtained. It was found that increased pressure during pelletization results in increased attractive forces, due to increased interparticle contact areas. FTIR analysis showed that chemical interactions occur between coal fines and the binder, as evidenced by the formation of new C-O ether-type bonds. The presence of moisture during pelletization enhanced surfactant activity of the binder. Chemical interactions between the coal and the binder seem to be mainly electrostatic, driven by Ca2+ from the calcium lignosulphonate, which may act as a bridge between the anionic parts of the binder and the surface of the coal. IntroductionCoal has over the years remained South Africa’s major energy source, with over 90% of the country’s electricity being produced via coal-fired processes (Arndt et al., 2016). Sasol’s coal conversion technology alone provides more than 40% of South Africa’s liquid fuel requirements (van Dyk, Keyser, and Coertzen, 2006). The production of high-grade coal requires the processing of run-of-mine (ROM) resources by a combination of processes which include crushing, screening, and washing (Radloff, Kirsten, and Anderson, 2003). These processes result in the generation of coal fines (< 0.5 mm) which, until recently, have been discarded into slimes dams (le Roux, Campbell, and Smit, 2012). Several issues are associated with slimes dams, among which are the costs of transportation of these fines from the place of origin to the discard point (often a considerable distance), and the potential environmental effects due to seepage of toxic materials into surrounding ecosystems (Clausen, 1973).Consequently, utilization of these coal fines is an area of great interest. Mechanical densification of fine coal by means of pelletization and/or briquetting to larger sizes for use in technologies that require lump coal, such as chain-grate stokers and fixed-bed gasifiers, has been shown not only to reduce environmental risks (Mangena et al., 2004), but also to significantly reduce storage and transportation costs (Mani et al., 2001). Pelletization is the process by which solid particles are consolidated into uniform, usually hard, impact-resistant agglomerates, rendering them useful as a fuel with sufficient calorific value for domestic and industrial utilization (Finney, Sharifi, and Swithenbank, 2009)."

Dec 1, 2018

By C. Tokoro, T. Kato

The objective of this study is to improve the shrinking core model for particles with a particle size distribution and clarify the activation mechanism of rare earth elements dissolution by mechanochemical activation. To achieve this objective, the method, called the doubly integrated micromodel, was applied for a shrinking core model in this study. This method consists of integrating the batch leaching rate of a single particle over the distribution of both feed particle size and reactor residence time to arrive at the fraction unleached. The usefulness of the shrinking core model improved by doubly integrated micromodel was confirmed by comparing it with a shrinking core model. To apply the shrinking core model improved by doubly integrated micromodel to rare earth elements dissolution from weathered residual rare earth ores by mechanochemical activation, leaching experiments were performed for grinding samples by planetary ball milling. The reaction equation of mechanochemical reaction by planetary ball milling for weathered residual rare earth ores was investigated by x-ray absorption fine structure analysis. As a result of a kinetics study, the rate-determining process of leaching changed from reaction to diffusion reaction control by planetary ball milling. Based on these results, it was revealed that the main mechanism of activated rare earth elements dissolution from weathered residual rare earth ores was a mechanochemical reaction by planetary ball milling. Keywords: Mechanochemical reaction, particle size distribution, shrinking core model

Jan 1, 2020

By S. V. Lukichev, O. V. Nagovitsyn, V. V. Laptev

In this paper the authors describe the developed algorithms of short- and medium-term planning of underground mining operations. The algorithms were developed using the example of the flat-back cut-and-fill method, and provide multifactor accounting of mining conditions, technical and technological limitations: state and properties of the rock mass; the current mining situation; mining rules; availability of safety pillars; properties of the filling; additional characteristics of technological objects that complicate the driving of workings; sufficiency of human and technical resources; employee specialisation; existing machinery and equipment; opportunities and limitations of the transport scheme of the mine, and work schedule. The paper is presented by means of a dynamic model of mining development, which shows the sequence of mining operations in the mine workings. Besides animation, the tool provides an opportunity to form tabular and graphical reports.

Sep 1, 2021

Since 2001, the Hybrid Stress Blast Model (HSBM) project members have developed a software suite to model the complete blasting process from non-ideal detonation to muck pile formation. To preserve the physics and improve solution time, the breakage engine uses a combination of analytical models and 2D axisym-metric finite differences to model near-field crushing, coupled to 3D discrete lattice fracturing and distinct element numerical methods to model throw and muck pile development. The model has been validated by comparison with laboratory and field tests in kimberlite. Multiple blasthole simulations are used to demonstrate how changes to blasting parameters can influence downstream efficiencies. Case studies of wall control blasting show that the presplit design must balance the two opposing effects of increased damage with increased charge and decreasing attenuation of the seismic waves with decreasing charge. Modelling of decoupled explosives needs further development. Reducing the charge towards the back of the trim blast results in a much more significant decrease in back damage than altering the timing. The model demonstrates how separation along the weaker planes in a jointed rock can coarsen the fragmentation, leading to inefficient beneficiation, and extends the damage to a distance of at least twice the burden behind from the blasthole, severely compromising the wall stability.

Jan 1, 2012

By E. Schoeman

Ion exchange resins were investigated for the effective recovery of platinum, palladium, and gold from a pregnant cyanide heap leach solution. Screening results indicated that strong-base anion exchange resins proved to be most effective in the recovery of these metal cyanides. Gold was selectively recovered with the use of Minix, while effective recovery of gold, platinum, and palladium over the base metals, copper, and iron, was achieved with Amberlite PWA-5. Successful elution of these metal cyanides was possible from both Minix and Amberlite PWA-5, using a 2M potassium thiocyanate solution at ambient temperature. Acidic thiourea was unable to elute platinum from either Minix or Amberlite PWA-5. Effective elution of palladium and gold were, however, achieved with use of acidic thiourea. Using these results, two conceptual flow diagrams for the recovery of these metals from cyanide solutions are proposed.

Jan 1, 2012

By R. M. Stroh, D. F. H. Grave

In this paper ventilation planning methods are discussed, with particular reference to the application of computer techniques to the solving of the many problems associated with the forecasting of ventilation and refrigeration requirements in mines of high production rates going to depths and rock temperatures higher than previously experienced. The use of the Starfield-Dickson programmes for calculating heat flow into airways and advancing stopes is demonstrated in the case of ventilation planning on a large mine extending to a brief depth of over 3 km below the surface. The possible effects of new mining methods on ventilation requirements in the future is briefly discussed.

By D. G. Krige

The scope and salient features of a general risk-analysis model for the main types of new mining ventures are covered in brief outline. The following special features and their effects on the investment criteria are discussed: - various criteria for viability, - the maximum shortfall of funds, - correlations between the grades of up to five ore constituents and between the corresponding product prices. differential inflation and escalation rates for costs and prices, - the estimation, if relevant, of a pay limit based either on the major product only, or on the two major products jointly, - the likely recovery grades of all the products to be obtained when the ore-body is mined to any such pay limit. - an option to take account of the effect on the pay limit of any negative taxation on marginal ore, - investment analyses in current and real terms for individual groups of investors subscribing for equity and any loan capital on differential terms.

Jan 1, 1979