Search Documents

By F. M. L. Mulaudzi

Metal dusting is a corrosion phenomenon that occurs in strongly carburizing gas atmospheres at elevated temperatures. Reaction kinetics and product characterizations of Alloys 602CA and 800 were examined by scanning electron microscopy with energy dispersive X-ray analysis (SEM-EDX) and X-ray diffraction (XRD).The results showed that Alloy 602CA is more resistant to metal dusting than Alloy 800. Visual examination and SEM surface analysis showed that Alloy 800 suffered metal dusting attack after a relatively short exposure period. The amount of coke deposits increased on Alloy 800 with increased exposure from 96 to 336 hours. X-ray diffraction on the reacted surfaces identified graphite and austenite in both alloys and some iron oxides/spinel for Alloy 800.

Jan 1, 2012

By W. Ferreira

Steel is produced in a basic oxygen furnace from hot metal obtained from a blast furnace. A sintered iron ore with good hightemperature properties (strength and permeability) should be used as feed to the blast furnace. The quality of this sintered ore depends on the reactivity of the iron ore used as feed to the sinter plant during the lime assimilation step in the sintering process. The penetration test is the standard method for evaluating the reactivity of iron ore with lime. It is, however, difficult to determine the exact depth of penetration from the standard test. A new test method is proposed that allows automatic evaluation of iron ores in terms of lime assimilation with increasing temperature. A comparison of the coefficients of variation for the new and standard methods for each ore type demonstrates that the results of the new test are more reproducible and more precise than those of the standard method. The test is also less time-consuming and easier to implement.

Jan 1, 2014

By R. A. Wildenboer, R. F. Sandenbergh

Rare earth elements (REE) are present at concentrations of approximately 0.36 % in phosphogypsum stacks located in Phalaborwa, South Africa. The REE are present in the phosphogypsum in solid solution in the gypsum and as fluorine and aluminium rich precipitates. Recovery of the REE offers opportunities for valorization and reducing the environmental impact of the phosphogypsum waste. This paper presents the results of investigations into the leaching behaviour of rare earth elements and other impurities from phosphogypsum using aqueous sulfuric acid. The effects of acid concentration, temperature, residence time, and the influence of impurities were evaluated for their impact on the solubility of rare earth elements in a sulfate medium. It was found that a significant fraction of the REE can be leached from the phosphogypsum in a range of conditions much less severe than traditional hard rock rare earth processing conditions. The REE were leached at a sulfuric acid concentration of 110 g/l, temperature of 30°C – 40°C and a residence time of approximately 8 hours.

Nov 6, 2024

By K. C. Mills

The objective of this work was to provide process engineers with values of the physical properties of various slag systems involved in high-temperature processes. Software that calculates the thermo-physical properties of slags from chemical composition is available on the www.pyrometallurgy.co.za website. This paper outlines the principles underlying the various models available in the program. The software calculates the following properties of crystalline, glassy, and liquid slags (where appropriate) as a function of temperature: heat capacity, enthalpy, density, viscosity, thermal conductivity, electrical conductivity, and surface tension. We hope, in the future, to update the program to (i) add new models as they become available, (ii) remove any ?bugs? discovered in existing programs, and (iii) provide guidance on the limitations of individual programs.

Jan 1, 2011

By M. de Beer

The conversion of carbon-containing feedstock into liquid fuels can proceed via the Fischer-Tropsch synthesis, which is catalysed using supported cobalt catalysts. These catalysts contain noble metals to facilitate the reduction of oxidic cobalt species in the catalyst precursor to metallic cobalt, which is the catalytically active species for the Fischer-Tropsch synthesis. This is thought to occur via hydrogen spillover, i.e. the diffusion of atomic hydrogen over the support from the noble metal to the oxidic cobalt moieties. Noble metals may also affectthe dispersion of cobalt in the active Fischer-Tropsch catalyst. The economic aspect of the addition of noble metals to the Fischer-Tropsch catalyst is discussed.

Jan 1, 2014

By R. Simon, P. Pagé, L. Li, P. Yang

The Mathews-Potvin stability method is widely used in the Canadian mining industry as a starting point to determine the maximum dimensions of mine stopes. However, it cannot be applied to inclined (more frequently encountered) mine stopes without conducting numerical modelling to obtain the stress factor A, defined as a function of the ratio of unconfined compressive strength of intact rock to the induced principal stress on the exposed stope walls. The need to conduct numerical modelling significantly limits the application of the Mathews-Potvin method. In addition, given its empirical nature and main application for preliminary design, it is deemed undesirable to conduct numerical modelling, especially elaborate modelling. Alternatively, theoretical methods can provide a much simpler and quicker way to estimate stresses around stopes and the corresponding stress factors. Over the years, a large number of studies have been conducted to estimate stresses around openings excavated with various crosssections. However, theoretical or graphical solutions remain unavailable for mine stopes that typically consist of horizontal floor and roof, and two parallel inclined walls (hangingwall and footwall). To remedy this situation, a series of numerical simulations is first performed for openings with vertical and inclined walls, including typical stopes commonly encountered in underground mines. A group of empirical solutions is then formulated to estimate the induced principal stresses at the roof centre and mid-height of the stope walls. The validity and predictability of the proposed solution have been verified using additional numerical simulations. The proposed solution can thus be used to calculate stresses and the resultant stress factors A around typical mine stopes with any inclination angle and height to width ratio, under any in-situ stress state, without conducting numerical modelling.

Aug 1, 2021

By R. G. B. Pickering

Successful management of mining operations depend on the accurate and reliable measurement of performance as a monitoring instrument in a feedback and control loop. However, when changes are being considered, the probable effect of the change on bottom line results requires different measuring techniques incorporating an in depth understanding which can identify hot spots in the operation which exhibit strong sensitivity to change. The CSIR's Division of Mining Technology has therefore been devoting a considerable effort to the establishment of techniques which enable changes to be analysed in terms of their impact on the two key parameters describing mine performance, i.e. profitability and safety. This paper describes these techniques, outlines their application to some example situations and discusses planned enhancements. The first section of the paper addresses the profitability model, and this is followed by a section considering the mine safety model.

Jan 1, 1996

By G. Drennan, A. Cameron

"South African mining operations depend on the skilled professionals produced through the tertiary education sector. In geoscience courses at the University of the Witwatersrand, which lead into the mining sector, there has been a significant increase in student intake over the past 15 years. This increase has been characterized by a radical shift in demography: in classes where white male students once formed the majority, black female students are now in the majority. This demographic shift appears closely linked to policies addressing issues of social justice and transformation in post-apartheid South Africa. We document this change and consider the role played by employment equity legislation (as in the Mining Charter) and corporate social investment strategies in the mining industry, notably through bursaries offered to black female students. We also look at the changing needs of the industry, where the critical need for managerial skills, not just technical knowledge, is highlighted through data from surveys of past students and industry managers. Our findings indicate the need for a curriculum adjustment to meet these changing requirements, as well as more rigorous selection criteria for bursars than simply gender, race, and appropriate matric results. IntroductionThe South African economy has historically been linked to mining and the exploitation of mineral resources. South African mining operations are dependent on the professional labour that is produced through the tertiary education sector, with critical thinking, teamwork, and the art of negotiation having been identified as the crucial skills required for this industry (Sideropoulos, 2014). Over the past three decades the South African system of education has gone through a period of dysfunction that it is struggling to rectify (Maphai, 2014). This has impacted on the levels of academic preparedness of students applying for places in higher education. Concurrently, government and university policies have widened access to higher education in response to the need to address issues of social injustice and transformation related to South Africa’s history of apartheid. As a result, the number of students admitted to universities has increased dramatically. In the School of Geosciences at the University of the Witwatersrand (Wits), the increase in student numbers has been accompanied by a significant change in demographics: classrooms which in the past were dominated by white males have given way to classrooms in which black females are often in the majority. This demographic shift is related to legislation such as the Mineral and Petroleum Resources Development Act and the Broadbased Socio-Economic Empowerment Charter, developed to reshape the socio-economic and equity frameworks of the country (Botha and Cronje, 2015). Requirements aimed at transformation in terms of management, skills development, and employment equity, together with corporate social investment (CSI) requirements, have resulted in bursaries being made available to attract students from designated groups, which in turn has increased the number of black students, and notably black female students, taking courses in geosciences. However, due to the economic downturn, instability in the mining industry has recently resulted in the downsizing of some mines, with international investors pulling out of South Africa. This instability resulted in devastating strikes across all sectors of the mining industry (Stewart, 2013) and in Marikana, an important platinum mining area, the strike culminated in a deadly shoot-out between miners and police. The resulting tensions spilled over into the gold mining sector, resulting in further strike action, shaft closures, and retrenchments. These challenges have implications not only for the mining industry in South Africa, but for the tertiary education providers whose graduates would have been absorbed into the mine-related workforce."

Jan 1, 2017

By J. Hadjigeorgiou, G. Knox

There is a considerable wealth of information on the behaviour of rockbolts under axial loading conditions both in situ and under controlled laboratory conditions. However, there is comparably less data on the behaviour of rockbolts in shear. Several authors have contributed to the understanding of the behaviour of conventional rockbolts’ performance under shear loading. Much of this data have been gathered through experimental programmes conducted on sections of the rockbolt. Considering the continuous coupling between the rockbolt and borehole interface, the approach is justified. Due to the design premise of energy-absorbing rockbolts with discrete couplings, full scale testing is required to quantify the behaviour of the rockbolts. This paper reviews published results obtained from two testing facilities, which are the SINTEF rockbolt pull test rig in Trondheim, Norway and the Epiroc Combinations Shear and Tensile test rig in Johannesburg, South Africa, both capable of conducting full scale testing of rockbolts. Based on this high-quality database it was possible to identify three distinct responses of rockbolts in shear. The behaviour under load is controlled by the presence or absence of an encapsulation medium (resin/cement grout), the reinforcement mechanism, and whether the rockbolt is continuously or discretely captured. As a reference the results are compared to the performance in shear of conventional grouted rockbolts.

Nov 24, 2025

By D. Marcotte, R. V. Dutaut

In most exploration or mining grade data-sets, the presence of outliers or extreme values represents a significant challenge to mineral resource estimators. The most common practice is to cap the extreme values at a predefined level. A new capping approach is presented that uses QA/QC coarse duplicate data correlation to predict the real data coefficient of variation (i.e., error-free CV). The cap grade is determined such that the capped data has a CV equal to the predicted CV. The robustness of the approach with regard to original core assay length decisions, departure from lognormality, and capping before or after compositing is assessed using simulated data-sets. Real case studies of gold and nickel deposits are used to compare the proposed approach to the methods most widely used in industry. The new approach is simple and objective. It provides a cap grade that is determined automatically, based on predicted CV, and takes into account the quality of the assay procedure as determined by coarse duplicates correlation.

May 1, 2021

By T. Bezuidenhout, J. D. Visagie

In recent years the requirements for a barrier system between the waste body of tailings storage facilities (TSFs) and the natural ground (NG) has necessitated the use of HDPE-lined TSFs in South Africa and other countries. The addition of an HDPE liner creates an interface between, inter alia, the tailings and surrounding soils on the footprint of the TSF. It is known that low-strength materials beneath slopes can cause slope instability. One method which can theoretically mitigate this instability of a lined TSF is the addition of stability bunds along the footprint of the TSF. Altering the profile of the footprint to include slope changes which oppose the direction of the failure creates passive slices in a limit equilibrium analysis. The passive slices actively oppose the movement of active slices, resisting the mobilization of tailings, thus greater active slice forces are required to develop a failure surface running along the liner interface. Two scenarios are presented and compared. The first scenario retains the ground profile unaltered and the second scenario includes stability bunds along the ground profile. An in-depth assessment is made of the interslice forces and the interface shear stresses for each scenario. The theoretical background is discussed in greater detail to determine the mechanisms of reinforcement provided by the bunds.

Jun 2, 2022

By H. Han, Z. Gao, Y. Gao, W. Sun, J. Wang

Strategic Ca-bearing minerals like scheelite and fluorite are usually separated by flotation, yet the separation is quite difficult due to their similar surface Ca active sites. Compared with the conventional strong collector sodium oleate (NaOL), lead nitrate-benzohydroxamic acid (Pb-BHA), complex collector shows a better selectivity for scheelite, yet its high cost hinders its wide application. Therefore, a novel collector (Pb-BHA-NaOL complex) was initially developed in this work to overcome the abovementioned dilemma. The flotation results of a single mineral showed that Pb-BHA-NaOL had a better selectivity for scheelite than Pb-BHA. Under the conditions of sequential assembly of Pb, BHA and NaOL at the molar ratio of 240:120:1 and pH 9.0, selective separation of scheelite from fluorite could be achieved without adding any depressants. In addition, for the same preferred scheelite recovery, Pb- BHA-NaOL could also save approximately 20% Pb and BHA compared with Pb-BHA. The analyses of the zeta potential measurement and X-ray photoelectron spectroscopy indicated that Pb-BHA-NaOL showed stronger adsorption on scheelite relative to fluorite. Meanwhile, Pb-BHA-NaOL showed more adsorption modes and higher utilisation of Pb and BHA on scheelite than Pb-BHA, which was due to the accelerator, NaOL. Keywords: Scheelite, fluorite, lead nitrate, benzohydroxamic acid, sodium oleate, flotation

Jan 1, 2020

By A. Yañez, J. Yianatos, P. Vallejos, R. Grau

This paper presents an evaluation of the effect that the mineral feed characteristics have on the metallurgical performance in an industrial flotation circuit. Variables such as mineralogy, particle size, solid content and mineral grade were evaluated using a flotation simulator, which was previously developed and validated using industrial data from different concentrators. The metallurgical performance was evaluated not only from the point of view of recovery and concentrate grade, but also by analysing less common variables such as froth carrying rate, froth and collection recovery, water recovery and others. Then, new data from the industrial flotation circuit was used to complement this analysis and evaluate the simulator predictability by comparing simulated and measured data. The results allowed for the quantification of the significant effect that mineralogy and particle size have on recovery and/or concentrate grade. Therefore, the grinding stage and flotation cells design become important factors to avoid a significant loss in metallurgical performance when feed mineral characteristics change in an industrial operation. In this context, an evaluation of cells design and arrangement should be performed to compensate the loss in recovery and concentrate grade in order to find an optimal operating condition. Keywords: Flotation circuits, mineral feed, modelling, particle size, liberation, mineralogy

Jan 1, 2020

By M. Pawlik, N. Ghaffari Touran

The interactions between apatite and hematite were studied through zeta potential and stability experiments, for this paper. The zeta potential measurements were conducted in both background electrolyte and mineral supernatants. The difference in electrokinetic properties of minerals in the presence and absence of supernatant was explained in terms of the dissolution of minerals and the subsequent readsorption of dissolved species at the mineral-water interface. The stability measurements in individual and mixed mineral systems were also performed to identify the extent of interaction between apatite and hematite upon their direct contact. The results from stability measurements in individual and mixed mineral systems indicate that there is an interaction between apatite and hematite. Based on the results, the implications for the apatite-hematite separation process were discussed. Keywords: Apatite, hematite, dissolved ions, stability, zeta potential

Jan 1, 2020

The Annual General Meeting of the South African Institute of Mining and Metallurgy was held in Kelvin House, Johannesburg, on Wednesday, 27th August, 1975. Professor R. P. Plewman (President) was in the Chair. There were present 45 Fellows, 37 Members, 8 Graduates, 3 Associates, 4 Students, and 45 Visitors, making a total of 142. The President declared the Meeting open at 16h00. OBITUARIES The President: Ladies and gentlemen, it is my sad duty to announce the death of the following members of the Institute : M. Barcza, an Honorary Life Fellow and Past President of the Institute; J. A. Boyd, F. E. Keep, and J. H. Taylor, Life Fellows ; I. D. B. Corner, C. O'G. Deane, R. E. Gilmour, A. C. Hofmeyr, M. W. Howell, T. J. Robin, and F. S. Steinhobel, Fellows; J. J. Frankel, Member; and T. J. Higgs, Associate. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, I ask you to rise and observe a few moments' silence. MINUTES The President: May we confirm the minutes of the General Meeting held on March 12th 1975 and published in the June issue of the Journal? Agreed. WELCOME The President: It is now my very great pleasure to welcome the many members of our Institute and all the distinguished guests who have honoured us with their presence this afternoon. In particular, I would like to welcome our Honorary President, Mr R. S. Lawrence, President of the Chamber of Mines, and also our Honorary Vice-President, Mr T. L. Gibbs, the Government Mining Engineer. Ons is ook besonder vereer dat dr. Naude, die Wetenskaplike Raad-gewer aan die Eerste Minister, en mnr. C. A. J. Borman, Direkteur van die Witwatersrandse Kollege vir Gevorderde Tegniese Onderwys, hier aanwesig is om die vergadering by to woon. We are also honoured by the presence of some 19 Presidents, Vice-Presidents, and Chairmen of our sister scientific and technical organizations. I would particularly like to welcome Mr Gericke of the South African Council for Professional Engineers, Professor Pretorius of the A.S. & T.S., and Dr Lloyd of F.S.P.E. And then, also the Presidents of the Institute of Welding, Professor Robinson; of the Electrical Engineers, Dr Troost ; of the Certificated Mechanical and Electrical Engineers, Mr Gibbs; of the Geological Society, Professor Maske; of the Land Surveyors of the Transvaal, Mr Course ; of the Assayers and Analysts, Mr Williams; of the Mine Ventilation Society, Mr Martinson; of the Chemical Institute, Mr Goodman; of the Association of Mine Managers, Mr Pretorius ; of the Institute of Foundrymen, Mr Attenborough; of the Production Engineers, Mr Duggan ; and of S.A.F.U.E.S., Mr Avalle. Then, the Chairman of the Council of the Institute of Metallurgists, Mr Snow; the Vice-President of the Town and Regional Planning, Mr Reinecke; the Vice-President of the Association of Consulting Engineers, Mr O'Kell; and Mr Cronje, who is representing E.A.S.A. Finally, the Chairman of the Southern Transvaal Section of the Chemical Institute, Mr Bloom ; the Chairman of the Witbank-Middelburg Branch of our own Institute, Mr Hosking; and the Secretary-Treasurer of our O.F.S. Branch, Mr Bird. We also have with us Mr Trueman; the Deputy Manager of Kelvin House, Mr Mrost ; our Honorary Editor, Dr Glen; Mr Walford; and also some representatives of the Press. Finally, it gives me great pleasure to welcome those who will receive Honorary Life Fellowships tonight, and also the winners of our student prizes. MEMBERSHIP The President: Ladies and gentlemen, I have pleasure in announcing the names of the following candidates, which have been published in accordance with By-Law 5.2.5., and Council has elected them to membership in the following grades: Fellows: R. G. Boswell, R. W. Chadwick, D. R. Hardman, J. A. Holmes, T. J. B. Jones, and R. P. King. Members : M. A. Bridgeford, C. F. Bonney, H. E. Bartlett, L. G. Floyd, A. K. Haines, D. Hatfield, C. G. Heymann, M. J. Howes, J. B. See, E. van Greunen, and S. P. Swanepoel. Associate Members : J. Coetsee and R. P. G. Steyn. Graduates: J. J. de Villiers and J. C. King. Associates: B. J. Bucher, P. A. Combrinck, W. J. N. Gelderblom, L. S. Halasz, J. van Wyk, C. P. Visser, and A. Veress. Students: D. J. Claasens, P. C. Crous, D. H. Murchison, P. A. Rossouw, and J. P. L. Schultz. Company Affiliates: Airco Engineering (Proprietary) Limited and Deelkraal Gold Mining Company Limited. There have also been some transfers: Member to Fellow: J. B. Nangle. Graduate to Member: E. E. Eichenbergen, M. J. Hillbeck, L. A. Melis, P. J. Venter, and R. O. Wellman. Associate to Associate Member: B. M. Williams. I welcome the newly elected members to the Institute, and I congratulate those who have been transferred to a higher grade.

Jan 10, 1975

By V. Jokovic

Hydrocyclones are the most commonly used classifiers in the mining industry. The reason for this is their low operating cost and a small footprint. Data from plant trials where screens replaced hydrocyclones indicated that lower bypass of fines and sharper separation could improve breakage rates, with a positive effect on flotation circuit performance throughput. Despite the importance of classification, hydrocyclones have not received as much attention as more expensive comminution units, and their technological progress has been incremental. Noticeable water split (Rf) reductions of a semi-inverted hydrocyclone have been reported in the past. According to theory, the hydrocyclone with reduced Rf will improve classification of fines. A classification study using semi-inverted hydrocyclones was conducted to determine if a hydrocyclone could be operated in a way that would minimise misclassified fines. The classification performance of a semi-inverted hydrocyclone will be presented in this paper and other potential applications will be discussed. Keywords: Semi-inverted hydrocyclone, water split, misclassification of fines

Jan 1, 2020

By C. J. Pretorius

More than 30 percent of the global demand for zircon (ZrSi04) is supplied by South Africa. A significant amount of the zircon is exported, and beneficiated products are then imported for industrial applications locally. Beneficiating the zircon locally could have a positive impact on the local market, since zircon is only one of many such cases. Ammonium acid fluoride serves as an alternative anhydrous fluorinating agent for zircon in the synthesis of several metal fluoridesl.2. It provides an effective dry fluorinating method and is easier to handle than hydrogen fluoride or fluorine gas. Zircon exposed to extreme plasma temperatures dissociates and becomes more reactive. The reaction of the plasma-dissociated zircon (Zr02?SiO2) with the ammonium acid fluoride (NH4F?XHF, where x= 1 to 5) forms two main intermediate compounds (NH4)3ZrFr(s) and (NH4) 2SiF6(s), the latter decomposing to form volatile products at relatively low temperatures, providing easy separation of the silicon and zirconium compounds. The ammonium zirconate compound decomposes to form zirconium tetrafluoride (ZrF4), which can be further manufactured into zirconium metal, to name but one product. Data on the kinetics of the reaction of ammonium acid fluoride with zircon and plasma-dissociated zircon, combined with the thermo-dynamic parameters of the reaction, is essential for the development of an industrial process for the production of a precursor for the manufacturing of zirconium metal, namely anhydrous ZrF4. Both the reaction kinetics and reaction parameters will be included in this study, as well as some proof that the reaction proceeds to ZrF4 on a small batch scale. If the exact reaction parameters can be pinned down, a wide spectrum of anhydrous metal fluorides can be synthesized through this fluorination route.

Jan 1, 2012

By I. Soto, E. Córdova, A. Anani

The new caving megaprojects that are planned to go into production in the next decade have scheduled horizontal developments at very high rates, which are difficult to achieve. Research has been conducted that seeks to model the construction times for underground developments to determine the feasibility of achieving the planned rates. However, these previous attempts do not consider all the operational aspects that make up the mine development cycle. Here, we present a discrete event simulation (DES) model that individualizes each unit operation of the development cycle to determine the construction rates that new projects will be able to attain. The developed model was applied to the New Mine Level (NML) of the El Teniente Division (DET). The results indicate that it would be impractical to achieve the advance rates scheduled in the original plans if the unit operations of the mine continue to be executed using the status quo. The metres developed after six years in the sections analysed can be significantly improved by changing the maintenance strategy for the equipment (457 metres increase), orepass availability (194 metres increase), and the initial planning sequence (1 598 metres increase). It is recommended that the mine implements a flexible maintenance strategy, defines a strategy to ensure and increase orepass availability to contractors, and makes use of current simulation tools for a more robust development sequence planning.

Oct 1, 2022

Spiral concentrators are compact, cost-effective and generally efficient gravity concentration separators for a wide range of applications (for example: coal, beach sands, iron ore, chromite and tantalite). Large mineral processing plants consist of thousands of spiral concentrators resulting in large plant footprints (capital intensive) and the adjustment of splitters is time consuming, impractical and is in many cases neglected?high capacity (HC) spiral concentrators aim to address these shortcomings. As a result Exxaro Namakwa Sands is currently investigating high capacity spiral technology for the spiral circuit upgrade at the primary concentrator plants (PCPs). This article summarizes the rougher spiral performance evaluation that was conducted on different types of spiral concentrators (the traditional MG4 spiral concentrator and the high capacity (HC) spiral concentrator) under different feed conditions. In addition, the effect of slimes on the spiral concentrator performance was also investigated. Slimes rheology was linked to the poor concentrator performance at the higher slimes concentrations. The test campaign shows a sacrifice in recovery under design-feed conditions can be expected when using high capacity spiral concentrators in the rougher stage when compared to traditional spiral technology currently in use. Both spiral concentrators show a detrimental impact of slimes on the performance, but the high capacity spiral concentrator is more sensitive to the higher slimes conditions.

Jan 1, 2010

By G. P. A. Howe

"A computer model of the rutile, ilmenite and zircon industry was developed jointly by Associated Minerals Consolidated and Consolidated Gold Fields for exploring marketing strategies and making predictions over a ten-year period. The industry is described briefly and the reasons for modelling it and choosing a deterministic approach explained. The economic structure of the model and its level of complexity are discussed. The necessity and techniques for convenient input and clear output, the team composition and the method of work are discussed.The reasons for the choice of FORTRAN, large computers, remote batch terminals and the vital importance of fast turn-round are discussed.Costs in staff time and computing are given, with an assessment of the reasons for the success of the model. The model is used on a regular basis to aid management decisions."

Jan 1, 2014