Search Documents

By Joe Maher

Adequate mine roof support to insure the safety of men and equipment is essential to successful mining. It is also expensive, amounting to more than one-fifth of the total mining cost at the White Pine mine. Cost effectiveness is therefore a prime consideration in developing optimum roof support. Roof bolt length is an important cost factor. This Phase II work compared uniform four-foot length Resin Bolts with the hitherto standard alternating four-foot and six-foot Resin Bolts, aiming at more cost-effective roof bolting. The data generated under this Phase II show that there is no discernible difference in the roof support given by uniform four-foot, and by alternating four- and six-foot, Resin Bolts in the relatively difficult ground selected for a severe initial test comparison; subsequent data from less difficult ground led to the same conclusion, namely no discernible difference between four-foot and four-six foot bolting.

Jan 1, 1975

By David E. Nicholson

The Bureau of Mines has constructed a special compression chamber for developing stress-strain relationships of mine backfill and simulating the high compressive ground pressures encountered in underground mines. A one-dimensional, or Earth-Pressure-at-Rest model is proposed for backfills subjected to these pressures. Results of the compression tests performed in the chamber indicate that reliable stress-strain relationships can be developed from these tests. The primary objective of the test series was to evaluate the effectiveness of compaction of common backfills in retarding ground closure. Analysis of the stress-strain data shows an eightfold reduction in relative strain in optimum well-graded, compacted backfills over poorly graded, loose backfill material. Analysis of the one-dimensional compression test data also indicates a significant retardation of transmitted stress in dense compacted samples of backfill and natural sands. Although not fully understood, a deformation mechanism is thought to occur at the intergranular contacts in cyclic fashion causing frictional heat loss and a reduction in transmitted stresses in the densely packed materials. The experimental values of transmitted stress are compared with theoretical values of effective stress calculated from the one-dimensional compression relationships developed by Hendron (4).3 These experimental values of transmitted stress compare very closely with the theoretical values of effective stress.

Jan 1, 1968

By Steven W. Schmauch

The U.S. Bureau of Hines conducted e mineral resource survey of approximately 232,000 acres in part of the Humboldt National Forest, Nevada, during 1989. About 7S percent of the study area was covered with mining claims. About 1,800 samples were collected end analyzed for 16 elements. Geologic structure, including thrust faults, is the most important factor in the localization of mineral deposits in the study area. The Independence mine (formerly Jerritt Canyon), Big Springs, and Wood Gulch are the most well known active properties, all developed on large, low-grade, disseminated gold deposits. These deposits have produced almost 3 million ounces of gold and are known to contain more than 8 million ounces of gold. At least 10 barite deposits in the south end of the range have had significant past production and contain 0.2 million tons of resources. Numerous precious and base metal targets have been identified and in some cases quantified during this study.

Jan 1, 1992

By G. J. Colaizzi

The Bureau of Mines, at the request of local authorities in Rock Springs, Wyo., investigated and conducted through contracts a multistage program of exploratory drilling and pumped-slurry backfilling of 15 areas of potential subsidence in abandoned mine workings underneath that community. Initially, the Bureau in 1969 had recommended a program of gravity blind flushing of some of the inaccessible mine voids, and in 1970 a new technique, the pumped-slurry injection process, was tested for the first time in a site adjacent to the city's area of severe surface subsidence. Success of this initial testing program, and of a large-scale project in Scranton, Pa., led to further large- scale projects, funded by Congress, that resulted in the successful back- filling not only of all 15 target areas of potential subsidence in Rock Springs, but also of several areas in other States. Total cost of the projects in Rock Springs, including the original pumped-slurry test, was $3,243,993. A total of about 923,000 tons of sand was injected hydraulically into mine voids, rendering 178 acres of residential and central-downtown areas of Rock Springs less susceptible to subsidence damage. The pumped-slurry method was proved to be much superior to the gravity blind flushing method in term of the amount of solids that could be injected underground through a single borehole. However, there are special conditions that make this technique more or less applicable in different areas or underground configurations, as noted in the report's conclusions.

Jan 1, 1980

This report is the 26th in a series summarizing Bureau of Mines research and technologic work on coal and related investigations and the 8th of these reports to be issued on a calendar-year basis.1 It reviews briefly work in progress during 1961, and it provides references to publications by Bureau personnel during 1961 and also to a few older papers that were not cited in prior reports of this series. Details about some of the researches mentioned may be obtained by referring to the publications cited in the footnotes or in the further list in the Bibliography; other phases of work are reported here for the first time and will be covered in more detail by later publications. The coal program of the Bureau of Mines extends over the wide range of applied and theoretical studies indicated by the table of contents of this report. Applied studies are conducted in connection with the development and evaluation of new mining techniques, and the effective processing and utilization of coal and coal products. Analyses of coal, technical advice, and other assistance to Federal agencies in connection with fuel and boiler-water problems, and health and safety activities are among the practical services handled by the Bureau, Fundamental research such as that on coal structure and on the properties of coal is conducted because it will, over a period of the, furnish an increasing general knowledge about coal; scientists and engineers may use this knowledge in solving problems in mining and utilization of

Jan 1, 1963

By H. B. Carroll

This Bureau of Mines report evaluates the performance of commercially available portable instrumentation for the detection of carbon monoxide, carbon dioxide, oxygen, and methane at conditions simulating an industrial work atmosphere. Portable instrumentation included in the study was gas-detection tubes (length-of-stain and color intensity), catalytic detector, liquid absorption detectors, paramagnetic oxygen detector, galvanic detector, and pelement or hot-wire methane detectors. Evaluation of the instruments was in atmospheres with 50 and 80 percent relative humidities at 75° F and containing test gas concentrations of 0.1, 0.25, 0.50, 1.0, 1.5, and 2.0 times the thresh-old limit value. Correlation of the results from the portable gao analyzer with measurement from the standard instruments was made by calculating and plotting an estimated line of regression, prediction, and confidence limits and the correlation coefficient for each detector system. Relative humidity in the 50-to 80-percent range did not appear to contribute to instrumental uncertainties in either performance or operation. Considerable deviation in detection precision between the portable gas-detection systems and the standard systems was established, especially at the lower gas concentration levels. The main difference or inconsistency in toxic gas concentrations determined with length-of-stain tubes resulted from the observer's interpretation of the results rather than difference in the tubes themselves.

Jan 1, 1973

By F. W. Wood

The Bureau of Mines has sought clarification of the Ti-TiN system by studying the phases formed by diffusion reactions between titanium and titanium nitride. Reaction couples were prepared by embedding pockets of TiN powder in arc-melted buttons of titanium. Specimens were vacuum annealed at nominal temperatures of 800°, 950°, 1,200°, and 1,500° C. Metallographically mounted cross sections from reacted specimens and from some that were not annealed were examined optically, with an electron microprobe, with an election microscope, and by X-ray diffraction. Each annealed specimen contained a segregated core primarily of d-phase material, an ?-phase diffusion layer, an a-phase diffusion layer, and host metal. On the basis of corresponding microprobe analyses, and considering results of certain other research, a new phase diagram is proposed. It contains no qualitative innovations, only quantitative adjustments. Results were also analyzed from the viewpoint of diffusion behavior. Diffusion coefficients calculated for the ? phase were sufficiently scattered that the parameters are very tentative. Nevertheless, the diffusion behavior reported is in reasonable agreement with one of two prior studies if it is assumed that the earlier investigators were mistaken in their identification of the nitride phase in which the diffusion occurred.

Jan 1, 1974

By James W. Pennington

MERCURY, also widely known as quicksilver, ranks tenth in quantity in world output of nonferrous metals. However, its unusual and desirable combination of properties- liquid liquidity at ordinary temperatures, high density, uniform volume expansion, electrical conductivity, ability to alloy readily, high surface tension, chemical stability, and toxicity of its compounds -gives mercury an industrial and military importance out of proportion to the small physical size of the production industry. Although mercury has been known and used for over 20 centuries, until the 16th century consumption was small and chiefly in medicine. Since then mercury's applications have paralleled scientific advancements, kind current principal uses of mercury are in electrical apparatus, industrial and control instruments, agriculture, pharmaceuticals, and the electrolytic prepa¬ration of chlorine and caustic soda. Other materials may be substituted for mercury in come applications; yet, for those uses that require mercury's unusual combination of physical and chemical properties, there is no ideal substitute.

Jan 1, 1959

By Hugo E. Camargo

Noise Induced Hearing Loss is the most common occupational disease in the U.S. and of paramount importance in the mining industry. According to data for 2006 from the Mine Safety and Health Administration (MSHA), Continuous Miner operators accounted for 30.2% of underground mining equipment operators with noise doses exceeding the Permissible Exposure Limit (PEL). This figure becomes more significant considering that 49% of the 2006 national underground coal production was extracted using continuous mining methods. Thus, there is a clear need to reduce the sound radiated by Continuous Mining Machines. The first step towards efficient noise control of a Continuous Mining Machine requires identification of the various noise sources under controlled operating conditions. To this end, a 42-microphone phased array was used in conjunction with 4 reference microphones to sample the acoustic field of a machine in the Hemi-anechoic chamber of the Pittsburgh Research Laboratory. These data were processed using a frequency-domain beamforming algorithm to obtain acoustic maps of 5 sides of the machine. The focus of the test was on the conveyor noise since previous studies showed that operation of the conveyor is the most important contributor to the sound radiated by the machine. From the acoustic maps, the following potential areas for noise control were identified, and included: chain-tail-roller interaction, chain flight tip-side board interaction, and chain-upper deck interaction.

Jan 1, 2008

By H. V. Makar

Laboratory tests were performed to obtain a quantitative description of the effectiveness of sodium sulfate (Na2SO4) for removing copper from molten iron and to determine the effectiveness of Na2SO4 on actual auto scrap. The tests were conducted on induction melted heats of iron averaging 0.58 and 1.50 percent initial copper and on cupola-melted auto scrap containing 0.45 percent initial copper. The Na2SO4 was added in powder form in amounts ranging from 2.9 to 43.8 percent of the weight of iron being treated. The data showed that copper removal for the various Na2SO4 treatments followed a similar trend, regardless of the iron composition that was tested. The equation Y = 1 - e-3.23x approximately reflects the relationship between copper removal and amount of Na2SO4 added, where Y is the fraction of copper removed and x is the ratio of the weight of Na2SO4 added to the weight of metal treated. Copper removals ranged from 3.3 to 74.5 percent and reductions down to less than 0.10 percent final copper were achieved in the auto scrap. Copper removals were generally accompanied by sulfur removal, and initial sulfur contents ranging from 0.10 to 0.20 percent were reduced to as low as 0.02 percent. High temperatures and long slag reaction times tended to induce copper and sulfur reversion from the slag, but, generally, the Na2SO4 treat¬ments were effective up to approximately 2,820° F with reaction times not exceeding 7 minutes.

Jan 1, 1968

By R. K. Linn

The New Idria Mining and Chemical Co. owns and operates the New Idria mine in southern San Benito County, Calif. During 1957-59, the New Idria mine was the largest producer of mercury in the United States and its alltime production of over a half-million flasks was exceeded only by one mine. It is one of the oldest and most consistent producers in California. With the exception of 1921-22, the mine has an annual production of mercury dating back to 1854. This paper by the Federal Bureau of Mines describes the exploration, development, mining, and furnacing of mercury ore at the New Idria mine. Figure 1 is a view of the furnace plant of the New Idria mine. The purpose of this report is to promote the development and conservation of our mineral resources by dissemination of technological information on mining and processing procedures, and related practices at operating mines.

Jan 1, 1961

By G. L. Oldwright, Virgil Miller

"The data presented in this paper were collected at the smelter of the Consolidated Mining & Smelting Co. of Canada Limited, Trail (Tadanac), Brithish Columbia. The authors are greatly indicated to S.G. Blayrock, vice president and general manager; James Buchman, smelter superintendent; and the staff members mentioned in Report of Investigation 3243. The authors are exceedingly grateful to George Murray, assistant smelter superintendent, for his keen interest, suggestions, and help in carrying out this investigation.INTRODUCTIONThe methods of charign the blast furnaces at Toole and Kelloggs were noted in Report of Investigations 2957 and 3094 respectively. Report of Investigations 2957 cited (4 to 9 inclusive) Hofman's Metallurgy of Lead (p. 226) and the work of A.S. Dwight, Thompson and Sicka, the staff of the Engineering and Mining Journal, and L.D. Anderson, N.F. Collins, in The Metallurgy of Lead (Chas. Griffin, London, 1910) also gives (pp. 247 254) the principles that he believes govern the successful charging of the blast furnace."

Dec 1, 1934

By K. L. Whitehead

An examination of 60 mines, 11 illumination hardware manufacturers, and Q mobile face-equipment manufacturers was conducted to determine the state of the art of mine-illumination hardware, define lighting system installation and maintenance problems, and assess personnel acceptance of lighting. Longwall and mobile face-machine illumination were studied. Major problems on room and pillar installations include damage of exposed components, electrical failures, and reduced lamp life, with extreme variability in the degree of these problems. Most longwall systems had low or moderate maintenance requirements, cable damage being the most significant problem. Most mobile face-equipment operators liked their machines' lighting systems, but many complained of glare and other problems. Longwall lighting was unanimously accepted by face personnel, and most complaints were minor. Based on the survey, general installation and maintenance guidelines have been established, addressing hardware design aspects, approaches proved effective to minimize problems, and improper practices noted which are detrimental to effective lighting.

Jan 1, 1981

These proceedings consist of papers presented at a Bureau of Mines Technology Transfer Seminar in September 1981 for the purpose of disseminating recent advances in mining technology in the area of premining research. The introduction and descriptive papers discuss techniques and instrumentation used in premining research for metal and nonmetal mining and shaft design and borehole control for premine planning.

Jan 1, 1982

By Joseph Grumer

An instrumented spherical vessel has been used for many years to study laminar combustion waves. Concurrent measurements of flame speed and pressure-rise rates have led to evaluations of burning velocities, the pressure dependence of the burning velocity, and the expansion ratios of the gases passing through the combustion wave. For the most part, these studies have involved flames initially at atmospheric or subatmospheric pressure. The old spherical vessel used by the Bureau of Mines was not designed for use at elevated pressures. Moreover, being made of wrought iron, it was susceptible enough to corrosion to prohibit its use with many combustible mixtures that figure in industrial research. In mid-1956, under sponsorship of the Office of Naval Research, the Bureau undertook the development of a stainless steel spherical vessel capable of withstanding explosions of gaseous mixtures at initial pressures as high as 20 atm. and initial temperatures as high as 250° C. The design called for a double array (cross) of closely spaced small windows for observation of the flame as it traversed the vessel and a piezoelectric transducer to measure concurrently pressure-rise rates. Because no commercial contractor was willing to bid on the construction of such a vessel, it was built at the Bureau's Bruceton machine shop.7

Jan 1, 1961

By Paul Averitt

The coal-bearing rocks in Iowa occur in an arcuate belt across the central and southern parts of the State (fig. 1) at the northern end of the Western Interior coal field. Coal beds of minable thickness are sporadic throughout this area and are mined principally in the three districts indicated by dark shading on the index map, although coal occurs also in the areas indicated by light shading. The coal is mostly of high-volatile C bituminous rank in all parts of the State. SURFACE FEATURES The coal-bearing rocks in Iowa are concealed for the most part by a covering of glacial drift ranging in thickness from a few feet to several hundred feet. This covering has been dissected to form a gently rolling upland, rising from an elevation of 466 feet at the mouth of the Des Moines River to about 1,200 feet in Calhoun County in the central part of the State. The local relief, however, rarely exceeds 150 to 200 feet.

Jan 1, 1949

By J. R. Thoenen

In the summer of 1937 the authors began a series of time studies of the various processes employed in' the production of crushed stone. These studies, made at quarries situated in the eastern and southeastern parts of the United States, have not been completed, but to make results available to the industry as early as possible, it was decided to publish summaries of the studies made to January 1, 1939, as a series of progress reports. The first of these dealt with power-shovel loading and was issued as Report of Investigations 3461 in September 1939. The second, issued in September 1939 as Report of Investigations 3467, dealt with quarry haulage. The present report discusses analyses of time studies of primary drilling at the same group of quarries. OBJECT Or STUDY Pressure of business problems frequently requires the entire attention of quarry management, and in consequence internal plant economies often are neglected. Also, operating officials absorbed in their local problems are prone to overlook possible economies that would attract attention immediately were they critically examining another plant. The authors felt that technical studies at a number of plants, made by impartial engineers, might disclose opportunities to reduce costs or improve efficiency in internal plant processes.

Jan 1, 1940

By M. John Brodie

This report reviews the regulatory environment as it pertains to tailings management and disposal from mining operations, excluding coal and placer gold operations, in the state of Alaska. It is based on the EPA's staff position on an effective program to regulate mining wastes as presented in the May, 1990 Strawman II document, The unique conditions which occur in parts of the state, including a fragile environment, high seismicity and permafrost, are identified. The special waste management practices which are necessitated by these conditions are delineated. The report provides a detailed outline of the current technologies that are suitable for designing, constructing, operating and closing a railings disposal facility to meet environmental protection objectives. Cost implications to the mining industry of potential regulatory actions, such as the degree of groundwater protection are examined.

Jan 1, 1992

By O. W. Owings

"The handling and transportation of explosives and explosives supplies are inherently hazardous owing to their sensitiveness to impact and flame or electric arcs and sparks. Many accidents have occurred in the past during transportation of explosives, especially when they were carried by individual miners on man-trips. When electric haulage became the usual mode of transportation and shots were fired electrically, the hazards of carrying explosives and supplies on man-trips were fully realized, and in some mines all explosives were placed in one car, usually at the rear of the trip. Far-sighted managers saw the danger of this practice and provided separate trips for delivering explosives. This step was a definite advance in safety, but the latest achievement is the construction of special, rugged, nonconducting cars.Many coal-mining men have shown considerable interest in the construction of safe cars for explosives during recent months. Undoubtedly many others are interested in this phase of safety, therefore this circular is issued to give information on cars of this type now in use.Car A (fig. 1) is essentially a closed inner box separated from an outer box by an insulating lining of rubber. The double box is attached to a standard steel chassis that has spring journals and electric welding instead of certain rivets. The chassis is equipped with roller bearings. The over-all length from pin to pin is 11 feet, 9 inches; the wheel base is 54 inches, the track gage 42 inches, and the capacity eighteen 50-pound cases of permissible explosives. The box is 10 feet long, 6 feet wide, 3 feet high at the top of the arched roof, and 2 feet 9 inches at the edges. The top of the car is 46 inches above the top of the rail.The inner box is insulated from the outer box by two pieces of 1/4-inch switchboard.-insulating matting cemented together. To cover the top, two ends, two sides, and the bottom of the box requires 320 square feet of the l/4- inch matting.The walls are well-seasoned tongue-and-groove oak, 1 1/4 inches thick and 2 3/4 inches wide. A 1 1/4-inch air space is maintained by oak strips between the outer wall and the two thicknesses of 1/4-inch rubber matting. The inner box is made of 7/8-inch, well-seasoned, tongue-and groove oak fitted closely against the insulating matting. No nail, rivet, or bolt extends through the rubber insulation.The floor of the outer box is secured to the chassis by two sets of bolts through an intermediate piece of well-seasoned oak. One set of bolts is countersunk from the top of the intermediate piece of oak, and the other set is countersunk from the bottom. The countersunk portions are filled with ""insulate,"" an insulating compound. Adjacent bolts are at least 6 inches apart.The bed of the inner box is divided into six compartments by transverse strips of wood at the bottom and partitions near the roof. Each compartment accommodates three 50-pound cases of explosives. This arrangement prevents cases in adjacent compartments from touching, so that there is no possibility of end thrust of the entire load of explosives. Each inner compartment is 21 inches high, 5g inches long, and 16 1/4 inches wide. Separating strips at the floor are 3 inches wide and 1 1/4 inches thick. The outside dimensions of the 50-pound cases of explosives used are 17 1/2 inches long, 13 1/2 inches wide, and 12 1/2 inches high."

May 1, 1940

By John C. Machisak

STATISTICAL data on injuries and employment pertinent to metal mines and to their mills, and/or processing plants are presented in this Information Circular for the calendar year 1960. The information pertains to metal mines, as well as ore-dressing plants and primary nonferrous smelters, refineries and reduction plants, and their auxiliary works. These data are voluntarily submitted annually to the Bureau of Mines by the operators, and contribute greatly toward the promotion of safety in the mineral industries. The data presented are classified according to the principal mineral produced and include information on copper, iron, lead-zinc, gold-silver lode, gold placer, uranium-vanadium and miscellaneous metals. A breakdown of miscellaneous metals by commodities is shown in table 19, page 41. The data also relate to workers engaged in production, exploration, development, construction, and maintenance and repair work, as well as supervisory personnel and office-workers at the mine or plant site. Injury and employment data at metal mines and metallurgical plants in the United States for 1960 are shown under the following general sections: 1. General injury experience: Tables I-5-Data on injuries, injury-frequency and severity rates and related employment data, work location, and degree of injury.

Jan 1, 1963