Search Documents

By M. G. Zabetakis

This publication contains highlights of a 4-hour lecture and demonstration by the Bureau of Mines on the fire and explosion hazards of flammable liquids and solids, oxidizing materials, corrosive liquids, and compressed gases. The authors first presented this material as part of a 2-week course given to officers and enlisted men at the U.S. Coast Guard's Dangerous-Cargo Handling School, established at Fort Eustis, Va., in 1959. The Bureau was asked to present the lecture and demonstration because of the extensive experience of its researchers in handling certain harardous commodities.

Jan 1, 1961

By Ronald P. Hollenbeck

Shales in the Appalachian Region of Kentucky and Tennessee were sampled and tested to determine their use as raw materials for the manufacture of lightweight aggregate by the rotary-kiln method. Nine samples were obtained from eastern Kentucky and 143 samples were obtained from eastern Tennessee. As a result of preliminary testing of these samples, two sources in eastern Kentucky and 11 sources in eastern Tennessee were resampled for rotary-kiln tests. The rotary-kiln tests showed the two sources in Kentucky and seven sources in Tennessee contained shale that would produce satisfactory aggregate. Lightweight aggregate processed from these nine sources was tested in concrete shapes and was found to be suitable for use in structural concrete.

Jan 1, 1968

By Naoki Hosoya, Setsuo Maeda

This paper addresses establishment of an experimental system for measuring biodynamic response (BR) of hand-arm system at the NIIH in Japan. BR measurement system at the NIIH is nearly equivalent to NIOSH installed system. The feasibility of the system is examined through the apparent mass (AM) measurement of the empty handle and a set of calibration masses. Apparatus The grip force was measured by using the handle shown in Fig. 1. The handle has two force sensors (KISTLER, 9212) and one accelerometer (PCB, 356A12). A low-pass filter with 5 Hz cut-off frequency was used to the grip force from measured force signal. Figure 2 shows BR measurement system in this study. The push or pull force at the handle was measured by using the force plate (KISTLER, 9286AA). The grip force and the push / pull force were displayed on a monitor. The shaker (IMV, VE-100S) is used to vibrate the hand-arm system along the forearm axis (Zh direction) (ISO 10068, 1998; ISO 5349-1, 2001). In most situations force actions for operating tools are expressed by grip, push, pull and combined these actions. These actions can be simulated in the test system. AM was obtained by performing H1 estimator in the PULSETM system (B&K, 3109) and it is denoted at the one-third octave band center frequencies. [ ] Methods In order to investigate the reliability of the system, AM measurement of the handle was performed. It is assumed that the handle is rigid in the upper limit of adoptive frequency range in this study. This assumption is validated in AM measurement of the empty handle. A pseudo-random vibration in the frequency range of 10 to 1,250 Hz was used and its amplitude is 1.0 (m/s2)2/Hz with a flat power spectral density (PSD) in the experiment. Measured AM includes the mass effect of the measuring cap in a subject experiment. Compensated apparent mass AMc(?) is obtained by Eq. (1) 1-2.

Jan 6, 2006

By Galen G. Waddell

The Deep Creek zinc and lead mine afforded an excellent example of a relatively small underground mine operation that approached the low mining costs of large, highly mechanized mines, An open stope mining method incorporating sublevel benches and vertical long holes was used (fig. 1). Detailed descriptions are given on the exploration program, stope development, stoping procedures, and pillar removal. Pressure grouting was used to check the inflow of water and thus prolong the life of the mine. Statistics on mining costs and on electric power consumption, haulage from mine to mill, and milling costs are included.

Jan 1, 1963

By John A. Kiefer

Ground fault and overcurrent protection criteria for coal mine a.c. distribution systems were examined under a Bureau of Mines funded investigation. The report begins with a literature review which discusses relaying topics including instrument transformers, ground-fault pickup methods, static relaying, and comparison of relaying techniques. A chapter on ground-fault relaying provides recommendations for maximum and minimum pickup levels as a function of maximum ground current and power system line-to-ground capacitance. Research in the area of phase overcurrent protection has resulted in a complete set of procedural recommendations for the selection and setting of overcurrent relays and current transformers, molded-case circuit breakers, and distribution system fuses in coal mine power systems. The final chapter, which discusses relay system maintenance, introduces a unique test set which was developed by KETRON and used to test the performance of relaying systems in coal mines.

Jan 1, 1980

By Meherwan C. Irani

The Bureau of Mines is developing a new technological approach to handling the problems of fires in abandoned coal mines and waste banks. This new technology involves the accelerated combustion of "waste" coals in place (i.e., in situ) under controlled exhaust ventilation conditions, which allows for total management of the combustion products; including utilization of the heat produced" This new concept could significantly lower the costs of reducing the environmental and public safety hazards associated with waste coal fires, and could lead to the conversion of a coal waste to a coal resource. The controlled burnout technology has progressed from the laboratory stage to a full-scale field evaluation stage at the site of an abandoned-coal-mine fire. This first report describes the site selection, evaluation, and preparation, and the design and construction of the full-scale controlled burnout installation. Subsequent reports will deal with the results of the operational field trial.

Jan 1, 1983

By S. B. Christy

This report on the electrodeposition of gold and silver from cyanide solutions represents work that has occupied my time at intervals during the past 20 years. The investigation has been carried on simultaneously with my duties as professor of mining and metallurgy of the University of California. During shis long investigation I have been assisted in the details of the work by, a number of my former students, acting in turn as assistants. Particular mention in this connection is due W. H. Hilton, who graduated in 1900; C. T. Dozier, 1902; N. C. Stines, 1905; H. N. Herrick, 1907, and L. C. Uren, 1911. It is impossible to publish full details of the many thousands of experiments performed. Effort has been made to present only the essential data. Wherever possible, the results of the experiments have been expressed in diagrammatic form by curves showing the relation between the simultaneous variables of the experiments. It is necessary to show, as nearly as may be, the state of the art. This is difficult because of the meager literature on electrodeposition in the cyanide process; hence resort must be had to the specifications and claims of patents, most of which seem never to have been applied on a working scale. Such information consequently can not be taken at its face value. Expressing the essential ideas evolved in such specifications is no easy task. Clearly, in quoting from patent records it is not ·feasible to enumerate all of the specifications or the claims allowed the inventors. A statement of the chief contributions to the art in the patent cited must suffice. Legal details, of course, must be obtained from the original patent. In the study of patent literature, when one compares the ardent hopes of the inventors with the results realized from their efforts, it becomes clear that in the development of an art no one man contributes everything. Each subsequent inventor stands on the shoulders of the one who has gone before. It is only through the summation of the contributions of many inventors that the art as a whole prospers. On October 19, 1887, a British patent was granted to McArthur and Forrest for the use of dilute cyanide solutions for treating gold and silver ores. The rapid extension of this process, in various forms, all over the world, has almost revolutionized the treatment of ores containing precious metals. It is a remarkable fact, however, that long before this patent was granted there was issued, on February 5, 1867, to J. H. Rae, U. S. patent 61866, for an electrocyanide process. Thus a method of electrodeposition from cyanide solutions used for treating ores was invented 20 years before the McArthur and Forrest patent .was granted, although the process did not come into general use. On May 24, 1889, U. S. patent 403202 was granted to McArthur and Forrest for the use of zinc shavings for removing gold and silver from cyanide solutions. The use of finely divided zinc is still the standard method for recovering 'gold and silver from cyanide solutions. Since this patent was granted, many attempts have been made to replace the precipitation upon the zinc by methods of electrodeposition. It is the purpose of this report to give an outline of some of these methods, as well as to show the relative advantages and disadvantages of the zinc and the electrical methods of recovering gold and silver from cyanide solutions.

Jan 1, 1919

By Charles E. Whieldon

The importance of producing more oil from known petroleum reserves has placed increased emphasis on the application of secondary-recovery methods. Recently published reports3 4/ describe the results of waterflooding in Roane and Pleasants Counties, W. Va. (see fig. 1.) This report describes the Barron Kidd Oil Co.?s Santee waterflood project, Maxton sand, Burton field, Church district, Wetzel County, W. Va. (See fig. 2.) The Federal Bureau of Mines hopes that these reports will stimulate interest in improved waterflooding techniques, thereby discouraging premature abandonment of oil leases.

Jan 1, 1961

By R. P. Maloney

Since mining operations began in 1900, Government geologists and mining men have periodically recorded the presence of the minerals of mercury and antimony in the extensive gold placer deposits near Flat in the Iditarod district of the Yukon River region, Alaska. No serious effort was made to recover the cinnabar contained in the gold placer gravels, and there is no evidence that veins of cinnabar and stibnite exposed in the placer operations (as reported by the Geological Survey) were ever explored or developed. A large monzonitic intrusive, which is the dominant geologic feature of the immediate area, is believed to be the lode source of the valuable minerals in the placer deposits. In contact with the monzonite are argillite and quartzite, metamorphic products from the Cretaceous shales and sandstones.

Jan 1, 1962

By Thomas M. Barczak

The initial Support Technology Optimization Program (STOP),Version 1.0, was released at the 19th Ground Control Conference. This original program has since been updated to Version 2.3 which was released in May, 2001. This paper describes the additional features of Version 2.3, focusing primarily on the following three aspects: (1) including uncontrolled convergence into the design requirements for standing roof supports, (2) the addition of design procedures for cable bolts as an alternative secondary roof support, and (3) the addition of new standing roof support technologies. Another new feature which should facilitate the development of design criteria for standing roof support is the capability to define ground reaction curves through convergence measurements alone without having to make support loading measurements. There are several other new features provided in Version 2.3 which are only briefly addressed in the paper. These include: (1) additional graphics capabilities to facilitate rapid assessment of support comparisons, (2)an East-West designation for support selection to more accurately provide cost and support availability data, (3) additional safety measures including a safety factor to identify support design near the peak support capacity, checks to see if the support dimensions comply with aspect ratio requirements, and a measure of roof coverage for the design layout of the support system. These new features of STOP provide more capabilities to design and analyze secondary roof support systems for conditions which could not be fully analyzed in the original version of the program.

By D. R. Dollnar

At a mine in central PA, high horizontal stresses have caused long running roof falls resulting in hazardous conditions for the miners and the premature abandonment of panels. Because of these conditions, the mine requested assistance of the National Institute for Occupational Safety and Health (NIOSH) in utilizing the 'advance and relieve method to mitigate the affects of horizontal stress on the mine roof. "Advance and relieve" mining involves the removal of a pillar or a portion of a pillar during development, thereby creating a cave along one side of the panel. Following cave development, the horizontal stress is relieved over the workings adjacent to the cave in the active panel. The mine has used this system in three panels with a significant reduction in stress damage and no large roof falls.

Jan 1, 2002

By W. M. Dressel

In producing feed for a lead blast furnace, concentrates analyzing 70 to 80 pct Pb are sintered to produce a physically acceptable low-sulfur product which contains only about 50 pct Pb. Mixtures of PbS with varying amounts of SiO2, CaO, Fe 20., and ZnS were heated in an oxidizing atmosphere at 1,000° C; the products were cooled and examined to determine the problems involved in producing sinter with substantially higher lead levels. Microscopic and electron microprobe studies of the above products as well as experimental and commercial sinters indicate that sinters consist essentially of lead silicates, lead-zinc silicate, calcium zinc silicate, and spinel (ferrite). Lead oxide and lead sulfate areas appear to result from insufficient mixing of the materials prior to sintering. The data give an insight into the process and show that sintering results from a complex interaction of all constituents and that sintering is not simply a matter of diluting the mixture to control the oxidation of lead sulfide.

Jan 1, 1975

By G. J. Perrott, H. W. Clark

During the course of the cooperative smoke abatement investigation carried on by the Bureau of Mines , the city of Salt Lake and the University of Utah during 1919-1920 , a study was made as to the suitability of Utah coals for by-product coking with particular reference to low temperature coking . was done because it was realized that a smokeless fuel for domestic consumers was the best remedy for this class of smoke producer . A report of the technical side of the work was included in the final report of the cooperative investiga- Since this report was written (June 1 , 1920) further work has been done by other investigators .

Apr 1, 1922

By Magnus Persson

ISO8662-4, “Hand-held portable power tools - Measurement of vibrations at the handle - Part 4: Grinders” is under revision. The new revision shall harmonize ISO 20643 “Mechanical vibration - Hand-held and hand-guided machinery - Principles for evaluation of vibration emission” which, among others, requires measurements in three directions and declared values related to the upper quartile of real-use vibration. To get the most suitable test method, a round robin test was made for evaluation of the two test methods proposed by the ad-hoc group working with this standard revision. Methods Seven laboratories measured the vibration from four grinders of different sizes, with and without autobalancing units. The laboratories come from universities, health & safety laboratories and grinder manufacturers. Two measurement methods are evaluated with respect to repeatability and reproducibility: 1. Grinding on a well-defined mild steel bar with depressed center wheels according to detailed test instructions. The test sequence starts and ends with 10 seconds of running the grinder in the air, when measuring the unbalance contribution to the vibration coming from the unbalance of the grinding wheel. Between these runs the average vibration during 60 seconds of grinding is measured. Three operators do five grinding tests per grinder. 2. Measurements using an aluminum unbalance disc similar to the one defined in ISO8662-4. Each operator runs the grinder four times, between each run the unbalance is moved 180 degrees to avoid variations caused by the play between the test wheel and the spindle. The averaging time is 10 seconds. Each grinder is tested by three operators. Repeatability is the spread within a lab between operators and over short time period for one machine and reproducibility is the spread between laboratories and over longer time periods for one machine. Instrumentation and transducer location are chosen according to ISO8662-4 and circulated test instructions. Results Both the repeatability and reproducibility is poor for the real grinding test, see figure 1. The coefficient of variation for repeatability is approximately 40% higher for the grinding test and the coefficient of reproducibility is 60% higher for the grinding test than for the unbalance disc test.

Jan 6, 2006

By N. Malakondaiah

Several growth chamber and laboratory experiments were conducted to study the germination behavior of plant species on mine spoils and plant growth responses to nutrients on spoils and topsoils. Experiments were conducted to study the germination potential of some native and introduced species under various conditions. The seeds of green needlegrass, side oats grama, thickspike wheatgrass, crested wheatgrass, birdsfoot trefoil and emerald crownvetch were less tolerant, whereas those of alkali sacaton. durar hard fescue, slender wheatgrass, yellow sweetclover and alfalfa were most tolerant to the sodic mine spoil conditions. Addition of leonardite improved the germination potential of some of the poor genninators. Slender wheatgrass and yellow sweetclover were used as test plants to study the fertility status and productivity potential of stockpiled topsoils and spoils collected from Center. Glenharold and South Beulah of North Dakota. The topsoils were neither saline nor sodic but low in N and P. The spoils were neutral to alkaline with SAIL of 12-32, EC of 1.8-5.5 mmhos/cm, Olsen&apos;s P< µ4g/g, and total N <0.07%. Application of N and P together to the topsoils increased the yield of wheatgrass and sweetclover by 88% and 70% of their respective maximum yields, whereas near maximum yields were obtained for both the species by the same treatments to the spoils. The average yields on topsoils were higher than the yields on spoils. The concentrations of major nutrients were higher in plants grown on topsoil, whereas the opposite was true with the concentrations of Mn, Zn, and Cu. Growth chamber experiments were also conducted to study the growth responses of alfalfa, oats and slender wheat grass by the application of Mn and Zn to a sodic coal mine spoil which was previously used for pot culture experiments. Significant growth responses to Mn and Zn were observed in alfalfa but not in oats or slender wheatgrass. Fertilizing the spoil with Mn along with NPK increased the yield of alfalfa to 85% and with Mn + Zn to 99%. Growth responses and plant composition results of this study confirm that the application of major nutrients to spoils can accentuate Zn and Mn deficiencies in some plants.

Jan 1, 1982

By J. T. Popp

This Bureau of Mines study reviews the geological factors that affect methane in the Beckley coalbed in southern West Virginia, including overburden, coalbed structure, type of and changes in lithology above and below the Beckley coalbed, and presence of fractures in the coal and rock adjacent to the Beckley. Depending on the depth, the Beckley coalbed emits from 216 to 520 ft3 of methane per ton of coal mined, and the Bureau estimates that methane emission in a deep, extensively developed mine in this area may exceed 3,000 ft3 per day per ton of coal mined. Average face cleat and butt cleat trends in the Beckley coalbed measured underground are N 33° W and N 53° E, respectively. Close cleat spacing con¬tributes to the friable nature of the Beckley and provides easy movement for methane and water. Because rider coals, splits, and carbonaceous shales may contribute methane to mine emissions, predictions of methane emission based on gas content of the Beckley coalbed alone may be conservative. Beckley coalbed reserves in the study area are 234 million tons. The gas content of the Beckley coalbed averages 407 ft3/ton, and the coalbed gas reserves are 108 billion ft3.

Jan 1, 1976

By Harold P. Rue

The problem of removing hydrogen sulphide from natural gas has become within the last few years one of major importance to the natural gas and petroleum industry. Several gas fields in the United States produce natural gas containing hydrogen sulphide, and a number of oil fields produce gas which contains hydrogen sulphide. 3 The percentage of hydrogen sulphide in natural gas produced in these fields varies from a fraction of 1 per cent t6 as high as 20.5 per cent by volume. 4 Hydrogen sulphide is probably the most toxic gas associated with natural gas,5 and from the standpoint of health and safety it is important that the hydrogen sulphide be removed if the gas is to be used for domestic purposes. Hydrogen sulphide, besides being toxic and therefore a hazard to animal life, is under certain conditions an active corrosive agent and very destructive to equipment. 6 The annual loss caused by the corrosive action of hydrogen sulphide on equipment amounts to hundreds of thousands, perhaps millions, of dollars. 7 The largest percentage of natural gas produced in the United States comes from wells which also produce oil. This associated gas invariably carries with it light fractions of petroleum, which when separated from the gas, condense to the liquid form at ordinary temperatures and pressure. Commercial application is made of this natural condition, and "wet gas" is processed to obtain so-called natural gasoline by employing the principles of absorption, adsorption, or compression and subsequent expansion accompanied by cooling. In the manufacture of natural gasoline from wet gas which contains hydrogen sulphide, if this contaminating gas is not first removed, some of the hydrogen sulphide may oxidize to form free

Jan 1, 1932

By J. P. Schmid

Results of a comprehensive investigation of the impact of underground mine waste disposal on the health and safety of miners are presented. Information was gathered through an extensive search of American and foreign literature and personal communication with professionals in private industry and government. All conceivable health and safety hazards directly or indirectly related to underground mine waste disposal are analyzed, catagorized, and ranked on an industry-wide basis. Positive health and safety effects are analyzed and ranked in a similar way. Both potential and known hazards and positive impacts are included. Recommendations on abatement techniques for the various hazards are presented. Case histories of a fill-related accident in a metal mine and a health hazard associated wtih coal waste backfilling are included and causes and possible abatement procedures are discussed. The rule of management in the promotion of health and safety in backfilling operation is discussed.

Jan 1, 1982

By D. Harrington

The greatly extended use of the underground trolley-locomotive system for hauling coal without doubt was one of the most important factors in the rapid progress of coal mining and the increased production of coal in American coal mines during the period 1910-20. Much of the superior efficiency of production of our underground coal and metal lines should also be credited to the trolley locomotive system. The trend to mechanization of mines during the past 15 years, mere particularly the past 5 years, with higher production per man employed and greatly accelerated advancement of working places, has required increased use of trolley locomotives, necessitating larger equipment, higher speeds, and more &apos;frequent turn over of pit cars. This is re¬flected in increased size of locomotives and the use of larger mine ears (some with a capacity up to or over 10 tons); moreover, heavier rails and larger-size trolley wires have boon or ought to have boon installed. Trolley-locomotive haulage has proved to be rapid; economical, efficient, and productive; nevertheless; in spite of these advantages, so-many hazardous features and, unsafe conditions are involved and the price paid in life and property is so high as to justify the statement that the system should be scrapped if it cannot be operated under reasonably safe conditions. Since bare trolloy wires were introduced into underground mines, they have boon responsible for the death of hundreds of diners, property damage totaling millions of dollars, an indeterminate loss of tonnage through the abandonment of mines or parts of mines, and loss of time after disasters caused by fires or explosions originated by the trolley haulage system.

Jan 1, 1945

By Richard Stayner

Suspended seats perform two functions: Reduce effect of occasional large bumps; Reduce more continuous vibration at a lower level. The former needs high damping. The latter needs low damping. For most mobile work machines the inevitable compromise is generally better than a simple cushion seat, because that amplifies vibration at around 4 Hz which is a sensitive frequency for human vertical WBV. Why have standard tests for seat suspensions? • Seat suspensions are non-linear so any measure of performance depends on operating conditions. For comparison these need to be defined. • Seat manufacturers need benchmarks for product development; • Machine makers choose dynamic characteristics appropriate to their products; • Occupational health specialists wish to control operator exposure to Standard tests should be representative, repeatable and reproducible. These requirements are reviewed in relation to the history of seat test standards and the current position. Current position and history The current position is that we have standard tests for seats for agricultural tractors, earthmoving machinery, industrial (fork-lift) trucks. These tests comprise measurement of vibration transmission and of the rate of damping. Current standards developed as the technology developed, starting around 1960: 1. Test on machine driven over standard surface1. 2. Test on shaker reproducing standard surface. 3. Shaker input replaced by representative spectrum2. 4. Human subject replaced by dynamic dummy. (Not yet settled). Are standard tests representative? The development process has gradually moved seat tests further from reality. 4 hr samples of work exposure suggest that seats do not on average provide large reductions of vertical WBV3. For specific magnitudes of vibration they can work well. For low vibration, performance is reduced by friction and for severe vibration by length of travel. Recent work has led to a new test to quantify how a suspension controls over-travel 9.

Jan 6, 2006