Search Documents

By A. F. Baker

Laboratory flotation of synthetic coal-pyrite mixtures and high-pyritic-sulfur coal indicated that ferric chloride (FeCl3), aluminum chloride (AIC13), chromium chloride (CrCl3), and cupric sulfate (CuSO4) are potential pyrite depressants. For each metal salt there appeared to be a range of pH values and optimum concentration for selectively depressing pyrite in coal flotation. Pyrite was depressed in the pH range from 4.5 to 7.0 with ferric chloride, from 5.8 to 7.0 with aluminum chloride, from 6.4 to 7.1 with chromium chloride, and from 6.4 to 7.4 with cupric sulfate. Best separation of pyrite from coal was achieved in flotation solutions containing from 2 X 10-5 to 5 x 10-5 mole/ liter of each salt. In solutions containing excess salt concentrations, coal was also depressed. These Bureau of Mines tests demonstrated on a laboratory scale that, in solutions containing 4 X 10-5 mole/liter ferric chloride and from 1 x 10-4 to 2 x 10-4 mole/liter sodium hydroxide, the pyritic sulfur content of a Lower Freeport bed coal sample could be reduced from about 2.51 percent to less than 0.60 percent with recoveries of over 83 percent. The depression of pyrite appears to be due to the adsorption of positively charged colloidal metal hydroxide at the pyrite-solution interface. This hypothesis is supported by zeta potential determinations which showed that suspended coal and pyrite particles in solutions containing metal salts are positively charged in the pH range where depression occurs.

Jan 1, 1971

By Donald F. Reed

During the first 6 months of 1948 the Bureau of Mines investigated the titania, deposit on the Wynn 0. Christy property in northern Hot Spring County, Ark. The property is situated in Magnet Cove, about half a mile north of the Magnet Store and U. S. Highway 270 (fig. 1). The purpose of the investigation was to determine the extent and grade of the ore body and to obtain a representative sample of the ore in as nearly natural condition as possible for use in metallurgical testing. All of the titania that has been marketed from Arkansas mines has been in the form of rutile from a deposit about 2 miles west of the Christy property. The titania in the Christy property occurs principally as brookite, which, with fragments of novaculite, quartz, and limonite, is imbedded in red clay. It is difficult to recover a core of the material. Three types of drills - a diamond drill, a bucket drill, and a Baker cable-coring tool operated on a churn rig - were employed in an effort to procure proper samples in their natural state. The Baker tool was found to be the most efficient and to be capable of drilling to a depth of 150 feet, making 80 to 100 percent core recovery (fig. 8). Total footage drilled was 1,536.9 in 21 holes, of which 7 were diamond-drill holes, 13 were bucket drill holes, and one was drilled with the Baker tool. The ore body was found to be 900 feet long, 500 feet wide, and more than 141 feet deep and contained 5.8 percent TiO2 and 0.52 percent 1720. Most of the deeper drill holes bottomed in ore, and there is a possibility that the ore may persist to a depth of several hundred feet. The Metallurgical Division of the Bureau of Mines is conducting experimental work at the Mississippi Valley Experiment Station at Rolla, Mo., for the purpose of developing methods of concntrating and utilizing the ore.

Jan 1, 1949

By C. H. Fisher, Abner Eisner

"INTRODUCTION Sulphuric acid of various concentrations has long been used as a reagent in the determination of olefins and aromatics in hydrocarbon oils 4 such as gasoline, kerosene, and neutral oils from coal—tar distillates. Despite its long use, however, there is no general agreement as to optimum conditions and concentration of acid, and numerous methods and modifications have been recommended. In most cases, treatment of the neutral oil with 60 to 90 percent sulphuric acid, followed by distillation to the original endpoint to remove olefin polymers, is recommended for the estimation of unsaturated hydrocarbons. The distillate thus obtained is taken as olefin—free oil and used in later stages of the anlysis. Aromatic hydrocarbons generally are determined in the olefin—free oil by suphonation with more concentrated acid (96 to 100 percent and fuming sulphuric acid are recommended), the hydrocarbons not attacked and removed as water—soluble sulphonic acids being considered as saturated hydrocarbons. In some cases the saturates are examined further by differentiatingbetween cyclic (naphthenes) and acyclic hydrocarbons (paraffins). Generally this is achieved by physical methods, although strong sulphuric acid is known to react preferentially with some types of saturated hydrocarbons,It was the purpose of the present work to make a general study of this type of analysis and to investigate the reactions of hydrocarbons under conditions often used in analyses that employ sulphuric acid reagents. Since previous work is not in good agreement, the optimum concentrations of acid for the different stages of the analysis were determined. Several sulphuric acid methods previously recommended and new modifications were compared, two synthetic solutions being used as the reference oil. The results obtained are presented below under separate headings."

Dec 1, 1937

By Marvin E. Lane

This paper , which describes the mining methods and practices at the Hayden Creek lead mine of St. Joseph Lead Co. in southeast Missouri , is one of a series being prepared by the Bureau of Mines on mining methods , practices , and costs in various mining districts of the United States . The Hayden Creek mine is in the W 1/2 sec . 7 , T. 36 N. , R. 4 E. , St. Francois County , Mo. , about 1 mile southwest of the town of Frankclay ( fig . 1) . The mine is on the west edge of the mining district known as the Lead Belt . However , neither the ore body nor the underground workings are connected with those of any other mine in the district . In contrast with most operations in the district , underground haulage is entirely trackless , and nearly complete delineation of the large , well -defined ore body by drilling permitted comprehensive planning of development and mining in advance of shaft sinking . The ore differs in character and occurrence from that of the main ore deposits in the Lead Belt in that the lead mineral , galena , occurs in the dolomitic matrix enclosing granite boulders instead of in dolomite limestone .

Apr 1, 1957

By Walter Kawa

In connection with its research in producing synthetic liquid fuels from coal, the Federal Bureau of Mines studied reactions of iron and iron compounds with hydrogen and hydrogen sulfide in batch autoclaves. The Bureau hoped to gain indirect evidence regarding the chemical changes that iron catalysts undergo when they are used in the hydrogenation of coal. The information obtained may be helpful in identifying the active form or forms of iron catalysts. At 450° C., with hydrogen at hundreds of atmospheres and hydrogen sulfide at 1 or 2 atmospheres, the thermodynamically stable form of iron is ferrous sulfide in the case of the metal, magnetite, ferric oxide, ferrous sulfate, ferrous oxalate, or the chlorides of iron. However, complete conversion to ferrous sulfide was not achieved at temperatures of 400° to 500° C. for kinetic reasons. Extensive sulfiding of iron, magnetite, ferric oxide, and ferrous oxalate occurred below 400° C., and some conversion of ferrous sulfate to ferrous sulfide occurred at 400° C. In the hydrogenation of coal, ferrous sulfide is the form of iron likely to be available for heterogeneous catalysis when starting with the metal, oxide, sulfate, or oxalate.

Jan 1, 1960

By E. C. Lane

[This is the eleventh in a series of reports on properties of commercial motor fuels made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R) Committee and the Bureau of Mines of the United States Department of the Interior. The first report contained data, on motor gasolines sold during the winter of 1935-36.3/ The present report presents analytical data for 2,020 samples, reprecenting the products of approximately 120 companies, which, as in previous surveys, include both large and small suppliers. In addition, the Pacific coast is represented by data averaged the Pacific Coast Technical Group before being submitted and' are published exactly as they were received. As in previous surveys, the data are divided into the three groups of samples of regular-price, premium-price, and third-grade gasoline each group has been averaged separately. The number of samples, items, and old brands comprising each group, exclusive of the of the Pacific coast, axe as follows: Regular price, 1,071 samples, 29 items, and 77 brands; premium price, 608 samples, 235 items, and 72 brands; third-grade gasoline, 341 samples, 196 items, 78 brands. The meanings of these terms as used in tae surveys are as follows:]

Jan 1, 1941

By Roy E. Peterson

The Bureau of Mines has been developing and evaluating methods for beneficiating the large deposits of nonmagnetic (oxidized) taconite located on the western Mesabi Range. In this segment of the research, a sample representing about 0.5 billion tons of nonmagnetic taconite from near Grand Rapids, Minn., was beneficiated using a reduction roasting, magnetic separation, flotation process. The sample contained 32.1 pct iron and 49.1 pct silica. Tests were conducted both on a bench scale and with a 1,000-lb/h pilot plant. In the bench-scale research a con-centrate containing 69.0 pct iron and 4.5 pct silica was produced with an iron recovery of 82.1 pct. In the pilot plant, reduction roasting was conducted in a 35-ft kiln using lignite as the reductant and major source of fuel. Dust from the kiln exhaust was pelletized and recycled to the kiln. The roasted taconite was beneficiated by magnetic sep-aration and flotation to produce a product containing 67.9 pct iron, 5.5 pct silica, and 69.7 pct of the iron in the kiln feed. The cyclone separation in the grinding circuit was sharpened by demagnetizing the cyclone feed in a 400-Hz, 1,000-Oe magnetic field.

Jan 1, 1983

By Peter C. Wood

This report describes research directed toward the preparation of chemical oxygen (02) sources which exhibited improved 02 storage and reaction characteristics when compared to potassium superoxide (KO2). The initial focus of the research was the preparation of calcium superoxide (Ca(02)2) by the disproportionation of calcium peroxide diperoxyhydrate. The Ca(02)2) was characterized by chemical, thermal, and x-ray analyses. Several methods for scaling up the Ca(02)2 synthesis process were studied. Next, the reactivity of Ca(02)2 toward humidified carbon dioxide (C02) was evaluated and was compare o that of K02 under flow-test conditions approximating those existing in portable breathing apparatus. The reactivities of mixtures of K02 and Ca(02)2 or lithium peroxide towards humidified CO2 were also studied. Finally, an analysis of two commercial, K02-based, self-contained self-rescuers was conducted to determine the potential weight and volume savings which would be possible if Ca(02)2 or a mixture of K02 and Ca(02)2 were used as a replacement for K02.

Jan 1, 1983

By Dean H. Ambrose

Using three-dimensional (3-0) graphics computing to evaluate new technologies for computer-assisted mining systems illustrates how these visual techniques can redefine the way researchers look at raw scientific data. The U.S. Bureau of Mines is using 3-D graphics computing to obtain cheaply, easily, and quickly information about the operation and design of current and proposed mechanical coal and metal-nonmetal mining systems. Bureau engineers developed a graphics simulator for a continuous miner that enables a realistic test for experimental software that controls the functions of a machine. Some of the specific simulated functions of the continuous miner are machine motion, appendage motion, machine position, and machine sensors. The simulator uses data files generated in the laboratory or mine using a computer-assisted mining machine. The data file contains information from a laser-based guidance system and a data acquisition system that records all control commands given to a computer-assisted mining machine. This report documents the first phase in developing the simulator and discusses simulator requirements, features of the initial simulator, and several examples of its application. During this endeavor, Bureau engineers discovered and appreciated the simulator's potential to assist their investigations of machine controls and navigation systems.

Jan 1, 1992

By Friedel. Michael J.

The U.S. Bureau of Mines investigated acoustic emission (AE) and the Kaiser effect in six types of rock: St. Cloud gray granodiorite, Barre granite, Dresser basalt, Salem limestone, Berea sandstone, and a volcanic tuff. AE signatures were used for interpreting the rock deformation stage and for indicating mechanisms of failure in uniaxial compression. The research demonstrated the advantages of using the volumetric stress-strain curve, as opposed to the more conventional uniaxial curve, for correlating AE response signatures with deformation stages and fracture processes in the rock. Standardized experimental procedures were used for the AE monitoring. The Kaiser effect was shown to be capable of determining prestress levels to within a few percentage points in uniaxial compression tests. Also, prestress memory was shown to be retained in the rock for periods of up to at least. 5 months, the maximum period of testing. The Kaiser effect AE technology holds promise for providing a comparatively inexpensive and less complex method for examihing stress history in rock. However, since the conftning stress has a pronounced influence on the Kaiser effect, it must be considered in developing technology for determining peak fteld stresses based on the Kaiser effect.

Jan 1, 1990

By Oren C. Baptist

Umiat field contains the largest accumulation of oil discovered so far in Naval Petroleum Reserve No. 4 in Arctic Alaska. The Umiat anticline was tested with 11 wells; 6 produced oil in varying quantities. Behavior of the wells during testing was unpredictable. For example, one well was abandoned as a dry hole after all tests failed to recover any oil, yet an offset well, only 200 feet from the dry hole, produced 400 barrels of oil a day. The main oil reservoirs are less than 1,000 feet deep and are in the permanently frozen zone (permafrost). Reservoir pressures are low, and most primary production will be by expansion of gas-in-solution in the oil. Because of the unusual reservoir conditions and the difficulties encountered in drilling and completing the wells, the Department of the Navy asked the Federal Bureau of Mines to make laboratory studies of the reservoir sand to determine the cause of well plugging and to provide laboratory information, to be used as an aid in estimating oil recovery from frozen reservoir rocks under solution-gas expansion from low-saturation pressure conditions.

Jan 1, 1960

By Larry G. Stolarczyk

This report deals with information regarding a new Medium Frequency (MF) Wireless Communication System for underground mines. This new telecommunication system works on low loss electromagnetic wave propagation modes which allow it to provide quality radio communications almost anywhere in a mine. Tests show the MF system can provide improved safety and managerial control, increased productivity, better organizational team-work and reduced maintenance cost; furthermore, MF's unique design allows for easy installation at a minimum cost. This paper covers the following: 1) MF design plan, 2) Overview of mine radio communications systems, 3) Preparations needed for designing an MF system, 4) MF equipment, 5) MF installation, 6) MF design considerations, 7) MF design specifica¬tions, and 8) Recommendations dealing with MF system. Experiments in four mines are illustrated to demonstrate the success and via¬bility of the MF system. The mines range from small (500 tons/day) to large (67,000 tons/day) capacity and represent several different mining methods. The MF Wireless Communication System represents an advancement in mining communication and the groundwork for other advanced mine systems.

Jan 9, 1984

By W. M. Dressel

The Federal Bureau of Mines has obtained data by differential thermal analysis of the various minerals that represent the nation's resources in manganese. These data are supported by X-ray diffraction analysis, chemical analysis, mineralography, and optical mineralogy, and provide fundamental information on the response of each mineral to thermal treatment in oxidizing, reducing, and neutral atmospheres. The information can be applied advantage¬ously in the identification of manganese minerals. Its greatest potential value, however, lies in the application of the quantitative data on the reaction temperatures, rates, and products to the more efficient extraction of manganese from U.S. ores. Thermal analysis curves are presented for certain manganese minerals, namely hausmannite, bixbyite, braunite, pyrolusite, lithiophorite, cryptomelane, hollandite, manganite, rhodochrosite, and rhodonite. The original minerals and the products of their thermal decomposition were identified by X-ray diffraction analysis, supplemented by chemical analysis and mineralogical identification.

Jan 1, 1961

Air pollution control regulation$ already implemented or being considered for implementation require substantial investment of capital to remove the sulfur oxides from copper, lead, and zinc smelter gases. There will be an attendant increase in production costs and possibly an associated increase in the price of these metals to the consumer. The total investment and any resultant metal price increase will depend upon the control regulations that ultimately will be adopted by the individual States. Controversy has arisen between the metals industry and governmental control agencies regarding the status of stack gas desulfurization technology and the ability of industry to control sulfur oxide emissions to the degree proposed by some of the more stringent regulations currently under consideration. This paper evaluates the problems involved in achieving various degrees of control over smelter sulfur oxide emissions and the technology available to accomplish the task of assuring clean air. The estimated cost of compliance is reviewed for the copper, zinc, and lead industries, but principal at tent ion is given to the copper situation.

Jan 1, 1971

By William H. Schiffbauer

The U.S. Bureau of Mines has been investigating methods and technology that may improve safety and production when applied to existing mining machines. Toward those goals, the Bureau has developed navigation systems that provide machine positional information while in the production area. This research has been limited in the past because the Bureau had only one type of mining machine to do experiments. Addressing this problem, the Bureau, along with Carnegie Mellon University, has developed a generic vehicle emulator, in the form of a wheeled vehicle with an onboard computer, known as the Locomotion Emulator, that provides a software-selectable vehicle emulation package. Preliminary testing by the Bureau has shown that the emulator can accurately imitate the maneuvers of the software selected vehicle type. Now the Bureau can test their navigation systems on different vehicle types without having to procure each of the vehicles. This report completely describes the emulator as well as all the modes in which it can be operated.

Jan 1, 1991

By C. G. Maier

The present trend of chemicometallurgical research toward widespread and inclusive use of thermodynamic methods requires the inclusion of available data of this sort in any comprehensive metallurgical report . Such data for manganese are far from adequate for the full utilization of these methods . Even if our knowledge of these properties is weak , the collection of available figures is nevertheless well worth while , especially if their utilization in an approximate way may show inherent possibilities of application . No less important is the necessity for discovering the vital gaps in the existing information , to serve as a basis for further pertinent study . The utility of the thermodynamic methods of Lewis and Randall ( 234 ) 3 has become increasingly evident to metallurgists . It is true that at present no better approach to the general , fundamental problems of chemical metallurgy is available than close adherence to these methods . The effort is here made to collect and correlate , as far as possible , significant quantitative thermodynamic data on manganese and its metallurgically important compounds . There are considered here only the intrinsic properties of pure materials . The order maintained as far as possible will be as follows :

May 1, 1934

By G. R. Hopkins

Although many small refineries were dismantled in 1934 the total number of plants, including a few under construction, increased from 604 at the beginning of the year to a new high of 638 on January 1, 1935. The capacity also reached a new record, the total of 4,072,400 barrels of crude oil daily being about 45,000 barrels higher than the previous high of January 1, 1932. The number of refineries increased materially in 1933, following construction in east Texas and the building of many small plants in the Rocky Mountain district and elsewhere. Most of the new plants of 1933 were built to provide an outlet for crude or because the ratio between crude oil and gasoline prices appeared conducive to profits However, low gasoline prices and increased costs in 1934 dispelled the hopes for profits; many plants were shut down, and some were dismantled. The number of operating plants declined from 454 on January 1, 1934, to 435 on January 1, 1935, but the number of inactive plants increased from 137 to a new high of 196 during the same period. As indicated above, new construction was at a minimum in 1934, and on January 1, 1935, only 7 plants were being built.

Jan 1, 1935

By Foster Fraas

The objective of this research was separation of one highly conductive mineral from a second conductive mineral , a procedure which is impractical in commercial electrostatic separators using metal rolls . Such separators permit separation of nonconductive from conductive minerals . A new technique involved use of carrier electrode rolls specially prepared by anodizing and / or oxidizing at high temperatures to form suitable oxide surfaces . Specific oxides included aluminum , copper , and nickel . The significant result provided by the new surfaces was the extension of the separation range to higher conductivities , an extension in relative mineral conductivity from 10-14 mhos . The results are in accordance with the blocking- layer theory .

Jan 1, 1964

By Yael Miron

The presence of pyrite (FeS2) in coal can cause or contribute to several problems for the coal mining industry. These problems, which include spontaneous combustion, roof falls, floor heave, and accidental explosions in coal surface mining when ammonium nitrate fuel oil (ANFO) explosives are used, result from pyrite oxidation. Pyrite oxidizes exothermically in the presence of air and moisture to form a large variety of products, including hydrated ferrous and ferric sulfates, and sulfuric acid. Some of the products are reactive chemicals and strong oxidants. The volume of many of these oxidation products exceeds the original volume of the pyrite; as a result, the adjacent coal disintegrates and its surface increases, rendering it more susceptible to oxidation. The heat from pyrite oxidation raises the temperature of the adjacent coal, accelerating the oxidation and self-heating rates of the coal. These combined chemical, physical, and thermal effects are the cause of the aforementioned problems. When ANFO is used in surface coal mines and contacts ferrous sulfate, a highly exothermic reaction ensiles. Additional hazards are fires or explosions caused by the frictional ignition of methane when the pyrite in the coal is struck by a cutting bit during mining.

Jan 1, 1994

By R. W. Van Dolah

The Bureau of Mines t.ced its investigations into sympathetic detonation of ammonium nitrate (AN) and ammonium nitrate-fuel oil (AN-FO) to define the scaling law for safe separation from detonating AN-FO. Both missile- and non-missile-producing AN-FO donors, weighing up to 5,400 pounds, were employed with acceptors of the same size. The usual cube-root scaling law was not confirmed; exponents for the relationship S = f(Wx) for AN were 0.51 with non¬missile-producing donors and 0.61 for missile-producing donors. For AN-FO an exponent of 0.80 was indicated in the missile-producing case. AN-F0 in polyethylene bags appeared somewhat more easily initiated than bulk AN-FO. The efficacy of barricades in protecting AN charges was investigated. detonation distances were reduced from one-third to one-seventh when filled barricades were employed. The investigation was extended to dynamite with both types of donors. With 1,600-pound missile-producing donors and an equivalent weight of dynamite, initiation would be expected in 50 percent of the trials at 167 feet. The corresponding value in the non-missile case was 67 feet. The data developed in this program of sympathetic detonation will allow the development of a rational set of safe separation distances for AN, AN-FO, and explosives.

Jan 1, 1966