Search Documents

By Dwight L. Sawyer, Roy T. Sorensen

The Bureau of Mines has investigated the recovery of alumina by hydrochloric acid leaching of calcined kaolinitic clay . Bench- scale studies indicated that horizontal belt filtration was a pprraaccttiiccaall method for separating the siliceous residue from aluminum chloride liquor generated in the leaching step . Miniplant -scale continuous testing was performed to evaluate the filter circuits and to compare filtration response of different calcined kaolin feed materials and of different agitatorbaffle designs in the leaching reactors . Soluble alumina recovery with a single filter ranged from 94 pct with minus 10 -mesh feed more than 96 pct with minus 35-mesh or misted feed . Process advantages were confirmed for the calcined misted kaolin feed material prepared by a Bureau-developed misting process . With two filters in series , an overall filtration rate of 100 lb solids /hr.ft - 2 of filter area was attained with a soluble alumina recovery of more than 99 pct . More than 99.5 pct alumina recovery was obtained with a thickener and a two - filter circuit for either the minus 35-mesh or the misted feed . Modifications in leaching reactor design made to decrease particle- toparticle attrition were successful and significantly increased filtration rates and decreased flocculant requirements .

Jan 1, 1965

By Leo A. Schrider

This report analyzes the successful low-pressure gas drive in the Keener sand of the Bonds Creek oilfield, Pleasants and Ritchie Counties, W. Va.) and predicts its future performance. Core analysis from two wells and electrical and radioactivity logs were used to evaluate the reservoir characteristics. Production records over a 37-year period indicate that over 240,000 barrels of oil have been produced from the Keener sand by low-pressure gas injection. Decline-curve analysis shows that 165,000 additional barrels should be recovered from 108 acres of productive sand by continuing this secondary-recovery method.

Jan 1, 1966

By R. D. Brown

This Bureau of Mines report describes a new methodology for identifying and sorting scrap metals using two modern portable instruments: a thermoelectric sorter and a hand-held emission spectroscope. The method, tested on a 27-sample stainless steel and superalloy array, makes it possible to group and/or identify a typical mixture of high-value metal scrap in two or three steps, whereas as many as seven or eight steps are needed to perform the same separations using chemical spot tests. A portable fluorescent X-ray analyzer identified 19 of the 27 alloys in the sample array by name or type; these alloys are included in the microprocessor memory. The remaining alloys were identified by using the analyzer in its elemental analysis mode and comparing the results wit.h alloy specification chemistry.

Jan 1, 1984

By E. C. Tarpley, R. A. Drogowski, R. F. Abernethy

Three of the test methods frequently used for the determination of moisture in the analysis sample of coal were employed in analyzing a series of coals ranging in rank from anthracite to lignite . For most coals , the variation between the three methods are within the tolerances allowed between duplicate determinations by the same method . The processing variables studied included atmosphere , flow rate of atmosphere , inert atmospheres , oven temperatures , heating time , exposure of the dried coal to laboratory air , and surface area of the test sample . Unless close control is kept on these variables , erratic results will be obtained .

Jan 1, 1964

By Ronald Althouse

During the past five years under contract with the U. S. Bureau of Mines (BOM Contract J0308002). West Virginia University's Mining Extension Service (WVU-MES) has designed, developed) and delivered to the mining industry a comprehensive training program for Mine Rescue (MR) teams and a management planning tool for Mine Emergency Preparedness. The Mine Rescue team program is systematically built on a set of training objectives, backed up by content, allowing mine operators to conduct team training activities. These materials are user-ready, provide the MR principles and practices for both initial and advanced training, and supply teams with exercises geared to problem-solving activities. In addition to an instructor's program guide, the eight (8) modules that comprise the initial (20 hour) MR training are: an Introduction to Mine Rescue, an Introduction to Self-Contained Breathing Apparatus (SCBA), a set of modules covering each approved minimum 2-hour SCBA (i.e.) the Draeger BO 174-A. the McCaa) the Aerolox. & the Scott Rescue-Pak), and a manual on Auxiliary Apparatus as well as the Chemox Auxiliary SCBA. Advanced, annual refresher training (40 hour) is covered by seven (7) modules that spell-out the principles and practices needed to establish surface organization, to handle mine gases as well as mine ventilation, to conduct exploration, for fires, firefighting, and explosions, to rescue survivors and recover bodies, and to accomplish a mine recovery. Approved by MSHA in 1984 to meet requirements for 30 CFO. Part 49, these materials provide a basis for trainers' instruction, for comparison of team capabilities, for modifying programs resources, and services, and for program planning. The Mine Emergency Preparedness Program (MEPP) is used by management as a tool in the preparation of company personnel for handling a mine emergency operation. As a wholly new program. MEPP depends upon development of a Mine Emergency Organization and Emergency Operations Procedures. It also requires regular scheduling of drills) periodic mock emergencies, and evaluation of organizational responses and program performance beyond required training of mine rescue teams. MEPP materials are arranged into three sets of guides: 1) the Preparedness Program System Guides include an Executive Summary, a Program Director's Guide Mine Emergency Organization, and Emergency Operations Procedures; 2) the Emergency Organization (MEO) User's Guides cover the Rescue and Advisory Division, the Technical/Safeguarding Division, and the Surface Support Division; and 3) the Emergency Procedures (EOPS) User's Guides detail Containment Level Procedures, Notification Level Procedures. Mobilization Level Procedures, and Deployment Level Procedures.

Jan 1, 1986

By R. W. Geehan

The Yellow Pine zinc-lead mine, situated about 3-1/2 miles northwest of Goodsprings, Clark County, Nev., was explored by core drilling during the fall of 1942 and the summer and fall of 1944 by the Bureau of Mines in cooperation with the Federal Geological Survey. The Yellow Pine district was located in 1855. The original claims covering the Yellow Pine mine were located in the following years: Rover, 1892; Hilo, 1897; Bybee, 1900; Radio and Como, 1906. The mine was operated by the Yellow Pine Mining Co. from 1906 to 1929. This company was dissolved in 1935. At a later date, S. E. Yount and the Security First National Bank of Los Angeles, Calif., acquired ownership of the mine. Since 1939, the mine has been operated in a small way by leasers. Production has been at least 175,000 tons averaging about 10 percent lead and 25 percent zinc, with a gross yield of $5,785,174. Virtually all ore produced by this mine consisted chiefly of oxidized zinc and lead minerals and came from long, pipelike shoots in the 100-foot thick Yellow Pine limestone. Ore shoots are sharply defined; elsewhere, the limestone is nearly barren. Numerous faults cut the mine into blocks. Ore is now mined in an open stope, but in the past, large tonnages wore mined in stopes by square-set methods. Ore produced recently was shipped direct to smelters unprocessed; in the past, it was milled by gravity and produced separate lead and zinc concentrates.

Jan 1, 1949

By John C. Edwards

The Bureau of Mines developed a mathematical model to predict the oxygen requirements for a miner evacuating a mine. The model accounts for variations in the miner's escape speed with mine airway height, and for the empirically determined expressions for the weight-specific oxygen uptake rate for upright walking, stooped walking (duck-walking), and crawling. A Fortran computer program that is user oriented was prepared based upon the model's constitutive equations. Specific instructions for utilizing the program, as well as applications to miner evacuation from a mine, are presented.

Jan 1, 1986

By P. G. Kovalchik

Safe electrical operation of shuttle cars depends upon maintaining the trailing cable's conductor temperature below 90° C. However, trailing cables are wound on and off reels, which changes the heat transfer characteristics of the cable-reel system. Derating factors for trailing cables are an attempt to adjust for this changing heat transfer mechanism in a practical way. The U.S. Bureau of Mines conducted research to determine acceptable derating factors for reeled mine trailing cables, using four cable-reel combinations, representative of industry usage. Cables were continuously and intermittently loaded at different duty cycles with direct currents of different magnitudes. Relationships between the average temperature rise and current load were established for each layer of each cable. Two models were constructed; one used empirical data from the continuous and intermittent load tests, and the other was based on thermodynamic theory. Results obtained from the theoretical model were compared with those from the empirical model for the rated temperature rise of the cable. Both models can be used to simulate a variety of test conditions including those that normally cannot be conducted in the laboratory. This information was used to determine acceptable derating factors for each layer of these cable-reel combinations.

Jan 1, 1994

The Bureau of Mines is establishing design criteria for effective roof support systems and is developing technology to improve mine planning and design. Geologic studies, surface and underground mine monitoring, and laboratory evaluations were conducted. The seven papers in this proceedings Information Circular present results of several investigations. Addressed are problems existing in both longwall and multiple-seam mines. Discussions include the effect of dewatering at a longwall mine site in the Pittsburgh coal seam and the effect of chain pillars on subsidence. Other results are measurement and characterization of longwall rock mass movement and an integrated design for stability in multiple-seam mining.

Jan 1, 1987

By Walter Wood, J. T. H. Cannarella, H. F. Yancey, R. E. Zane

More than 50,000,000 tons of bituminous coal and probably about the same quantity of anthracite are cleaned annually in the United States by wet methods. The water, fine coal, and impurities from the water used for washing ordinarily are recovered by moans of various forms of settling tanks. Settling and clarification may be hastened markedly, thereby greatly increasing the capacity of clarification equipment already installed, by the addition of substances to the washery water that cause the fine particles in suspension to agglomerate and thus settle more rapidly. This phenomenon, although well known and applied in other fields, has been used at only a few coal washeries in the United States. It is widely employed, however, as an aid in the recovery or disposal of fine coal or impurities, as a means of preventing, stream pollution, and to enable reuse of washery water at many plants in Europe. Pioneering work in the United States has been done principally by two companies -- the Pittsburgh Coal Co., in Pennsylvania, 6/ and the Pacific Coast Coal Co., in Washington.

Feb 1, 1940

By F. J. Perzak

The Bureau of Mines conducted a study to develop a standard fire test for 5-gal containers used for storing combustible fluids in underground coal mines. A standard test method was developed which evaluates the performance of the container in a 4-min tray fire. Bureau investigators used the standard test method to evaluate several types of closed 5-gal plastic and metal cans in outdoor tests. Each can tested contained 1 gal of nonfire-resistant (NFR) hydraulic oil. A container failed the test if it lost its contents in any of seven trials. Contents spilled either as a result of thermal rupture or melting. Fewer than 10 pct of the metal containers failed this criterion, but all the plastic containers failed. The metal container failures were usual-ly due to tipping over during pressure relief, which spilled the NFR oil. Replacing the NFR oil in the container with kerosene resulted in failure of more than 30 pct of the metal containers. The standard tests and preliminary tests showed that plastic containers are not equivalent to metal containers in their ability to contain combustibles such as lubricants and greases in a fire. For solvents and lubricants more volatile than NFR hydraulic oil, approved metal safety containers are recommended.

Jan 1, 1985

By Joseph Blake Smith

Coal resource data from published sources and company files were used by the Bureau of Mines to determine the location and extent of strippable coal reserves in Wyoming. Total strippable reserves of 23 billion tons were estimated in seven major coal areas. Seven large strip mining operations were active in 1969, and their production totaled 45 million tons of coal. Cutoffs used to define strippable reserves were (1) minimum coalbed thicknesses of 5 feet; (2) overburden-to-coal ratios of less than 10 cubic yards of over- burden per ton of coal; and (3) total overburden thicknesses of less than 120 feet, except where reserves occur in multiple beds or a single thick bed. Tertiary rocks along margins of the Powder River basin contain most of the strippable coal reserves in Wyoming. The Wyodak beds, ranging in combined thickness from 30 to 1.30 feet, crop out on the east flank of the basin and contain an estimated 19 billion tons of strippable subbituminous C-rank coals under less than 200 feet of overburden. Partings between these beds total less than 60 feet. The 100- to 200-foot-thick. Healy bed on the western flank of the basin and the 35-foot-thick School and 20-foot-thick Badger beds on the south also contain large strippable reserves. Elsewhere in Wyoming, strippable reserves. Elsewhere in Wyoming, strippable deposits are subbituminous coal of Late Cretaceous and Tertiary ages, mostly in the Hanna and Great Divide basins in the south-central portion of the State and in the Kemmerer-Hamms Fork region in the southwestern corner.

Jan 1, 1972

By J. A. CoRGAN, J. A. DECARLO

The coal -carbonizing industry is recognized as one of our country's most essential industries , and this position has been achieved through its primary function as a source of supply of special fuels and chemical raw materials . When coal is carbonized at high temperatures in slot - type coke ovens in the absence of air , it decomposes into two main products cokę ... and crude gas . Of these , the more important is coke , a hard, strong, porous solid that remains in the oven after the volatile matter in the coal has been driven out by heat . The hot crude gas carries with it all. of the coke -plant products except coke and has a complex composition in the vapor: state . Its processing , to produce the four principal coproducts of coke (tar , ammonia , light oil, and gas ) , is accomplished by preferential condensation and absorption . Although the principal coproducts of coke tar , ammonia , and crude light oil - - gas, are of secondary importance , their

Jun 1, 1949

By Howard P. Hamlin, John W. Sweeney

Shales , clays , and loess in Iowa were tested and evaluated to determine feasibility of producing lightweight aggregate by commercial rotary - kiln or sintering methods . Preliminary testing was conducted in a muffle furnace . Rotary - kiln tests were conducted in a 16 - inch by 14 - foot rotary kiln . Concrete cylinders and cubes were tested to determine qualities of the aggregate . Three samples made suitable lightweight aggregate by rotary - kiln methods and two by sintering .

Jan 1, 1964

By A. G. Loomis

Although secondary-recovery methods have not been applied widely in California, it is apparent that increasing attention and effort must be given to this phase of recovery if the State is to maintain its high rank as a petroleum producer. Steadily increasing demands for petroleum products and decreasing rates of discovery of new oil fields, with rapid depletion of existing reserves, emphasize the prospect of an adverse situation of supply and demand in the not-far-distant future. If the trend of discoveries becomes more favorable or if more complete economic recovery of the oil in place can be obtained by secondary recovery, this situation can be averted. Not only are these reserves of economic importance to the petroleum industry for meeting increasing market demands; but economic reclamation of such reserves is an important conservation measure, which will prolong the productive life of many fields. Accordingly, progressive operators in California are alert to the possibilities of secondary recovery and have done much to implement such operations wherever feasible. Most current operations are of the pressure-maintenance type, in which the reservoir pressure is maintained or partly maintained by injecting natural gas to in-crease oil recovery. The possibilities of recovering additional oil from stripper fields by gas drive and water flooding (including water disposal) also are being tested in experimental field projects. Table 1 summarizes current gas-and water-injection projects in California.

Jan 1, 1952

By G. R. Smith

This report describes research carried out by the Bureau of Mines to develop new technology for electrorefining metals at much higher current densities than those normally used in commercial practice, preliminary studies using rotating-ring and cylinder electrodes to increase the mass transport of copper are discussed. Following this work, single- and multichannel cells were developed that utilized a high electrolyte flow in the channels formed by the anode-cathode pairs. Using these cells, copper was successfully refined at current densities in the range of 70 to 300 amp/ft2. The effects of flow rate, electrolyte composition, and grain-refining and leveling agents on the morphology and purity of electrodeposited copper were determined.

Jan 1, 1979

By D. Bienstock

In connection with air-pollution studies, the Bureau of Mines is cooperating with the U.S. Public Health Service in investigating the use of solids for removing sulfur dioxide in concentrations of less than 0.5 percent from combustion and waste gases. Removal of sulfur dioxide at flue-gas tempera¬tures would no longer result in the cooling of scrubbed gas, which is inherent to liquid scrubbing processes used exclusively in industry today. Results are reported of extensive investigation, using metallic oxides as absorbents, adsorbents, and oxidation catalysts at 130° and 330° C. (temperatures at which flue gas may be treated in powerplant practice). The most active absorbents tested were the oxides of manganese, cobalt, copper, and alkalized alumina; 23 to 33 grams of sulfur dioxidn were removed by 100 grams of absorbent at 130° C., while scrubbing more than 90 percent of the sulfur dioxide from a simulated flue gas, and 19 to 61 grams of sulfur dioxide were removed at 330° C. A more detailed study is reported on absorption and regeneration, using manganese oxides and alkalized alumina. Adsorption of sulfur dioxide on activated carbons and molecular sieves at elevated temperatures is considerably less efficient than removal by absorption--a maximum of 7 to 8 grams of sulfur dioxide could be removed with 100 grams of adsorbent at 130° C. A potash-promoted vanadium pentoxide is effective in converting sulfur dioxide to trioxide; complete conversion in a simulated flue gas containing 0.35 percent sulfur dioxide was obtained at 365° C. Pilot-plant and cost studies are being made by the Bureau to determine the economic feasibility of removing on an industrial scale the sulfur dioxide present in gases in low concentrations.

Jan 1, 1961

By A. U. Christensen

THERMODYNAMIC data for many of the common interoxidic compounds are seriously lacking, and appraisal of possible ceramic or metallurgical applications depends upon dubious estimates. In particular, high-temperature heat-content estimates may be invalid because of unknown phase-transformations. This paper reports experimental heat-content values above 298.15° K. for five interoxidic compounds-the aluminates of lithium and sodium (LiAlO2 and NaAlO2), the ferrites of lithium and sodium (LiFeO2 and NaFeO2), and lithium titanate (Li2TiO3), as obtained by the Bureau of Mines. Sodium aluminate, sodium ferrite, and lithium titanate were found to have previously unknown transformations in the crystalline state. The heats and temperatures of these transformations were evaluated as were also the heats and temperatures of fusion of sodium ferrite and lithium titanate. The heat-content results are assembled in both tabular and algebraic-equation form for use in conducting thermodynamic calculations at temperatures in the range 298°-2,000° K.

Jan 1, 1960

By Walter W. Kaufman

This User's Manual, extracted from information contained in the Final Report for the above referenced project, outlines test procedures to measure the braking capabilities of underground non-coal rubber-tired mining equipment. Methods to interpret test results, recommendations for safe braking capabilities, and basic techniques to improve braking systems and road surfaces are also discussed. Possible applications for runaway vehicle protective devices other than braking systems are reviewed. Also included is a listing of mining equipment and brake component manufacturers who supply the majority of equipment to the United States non-coal mining industry. In conjunction with this list of manufacturers, a general tabulation of brake related specifications appears for vehicles observed during stopping tests conducted underground.

Jan 1, 1977

By Donald E. Redmon

This Bureau of Mines report examines the injury experience in the quarrying industry for the years 1964-65. Twenty-eight tables for each year are presented in which disabling work injuries are summarized by department, source of injury, extent of disability, part of body injured, and nature of injury. Correlative information on employment, worktime, and operating activity is also presented.

Jan 1, 1973