Search Documents

By M. F. He

There are three polymorphic modifications in pyrrhotite (monoclinic, hexagonal and orthorhombic), with monoclinic and hexagonal polymorph being more abundant. The floatability of different crystalline structures of pyrrhotite (monoclinic and hexagonal) is studied in this paper. It is shown that the floatability difference of monoclinic and hexagonal is obvious and that the flotation recovery of monoclinic pyrrhotite is greater than that of hexagonal pyrrhotite using different collectors . Using butyl dithiophosphate as collector, the flotation recovery of pyrrhotite is higher than when sodium diethyl dithiocarbamate and sodium butyl xanthate are used as the collectors. Monoclinic and hexagonal pyrrhotites are more easily activated by Cu2+ in acidic conditions than in alkaline conditions, while Cu2+ can not activate hexagonal pyrrhotite when sodium diethyldithiocarbamate was used as the collector. By the measurement of contact angle, it is indicated that monoclinic and hex-agonal pyrrhotite float well and are easily activated by Cu2+when dithiophosphate was used as the collector. Using sodium diethyl dithiocarbamate as a collector, the flotation behavior of pyrrhotite was investigated. The relationship between potential and pH range for pyrrhotite flotation was established. The results show that the flotation of pyrrhotite is dependent on pulp potential at certain pH values.

Jan 1, 2014

By X. L. Wang

Hydrothermal method was applied in the preparation of calcium sulfate whiskers in airtight re-actor using gypsum as primary materials. The optimum conditions of preparation are as follows: pH value 9.8~10.1, concentration 5%, material size 18.1µm, which were determined by the analysis of the diameter of CaSO4 whiskers through SEM. On these conditions a product of ultrafine CaSO4 whiskers with diameter of 0.19µm and aspect ratio of 98 is obtained. Ultrafine CaSO4 whiskers with different concentrations, modified by titanate NDZ-401, were added into polypropylene as intensifier and composites of Ultrafine CaSO4 whiskers/ polypropylene were prepared by melting-extruding method. Mechanical performance of the composites was tested and surface morphology of the composites was observed by SEM. The results indicated that impact notched izod of the composites was enhanced by 49.5% compared with pure polypropylene when 10.0% Ultrafine CaSO4 whiskers were added into polypropylene and toughening effect was very remarkable. Dispersion behaviour and interface phenomenon of Ultrafine CaSO4 whiskers in polypropylene matrix were investigated by SEM. The results indicated that Dispersion performance of Ultrafine CaSO4 whiskers modified by titanate NDZ-401 in polypropylene matrix is good, which improved mechanical performance of composites to some extent.

Jan 1, 2014

By Y. X. Yang

Bottom ash is a solid waste stream in a Waste-to-Energy (WTE) processing plant during the combustion of the municipal solid waste (MSW). In the Netherlands, bottom ash contains typically about 18% metals originated from the MSW, and current industrial practice could recover about 10% metals through magnetic and eddy current separators. The remaining 8% as the finer particles is difficult to recover through current physical separation technology. Among various alternatives, vitrification is one of the promising options to immobilize the ash and recover the remaining metals. During vitrification a homogeneous glassy slag and a Fe-Cu based alloy were obtained. In the cur-rent study, the metal alloy recovered from the bottom ash originated from a Dutch Waste-to-Energy plant contains about 82 wt% Fe, 12 wt% Cu and 6 wt% other alloying elements and impurities such as C, S, P, Ni etc. The generated alloy does not have direct commercial applications, and separation of copper from iron-based alloy is critical to obtain the market value of both copper and ferrous constituents. To find a suitable processing route of this metal alloy, various alternative approaches have been considered for an efficient removal of copper from the alloy, and the focus in the present study was on the sulphide treatment at elevated temperatures of 1400 ~ 1500oC. The tested sulphide systems include pure FeS, FeS containing sulphide mixture (such as Na2S and Al2S3), pyrite (FeS2) mineral, ZnS containing sludge as an industrial waste. It was found that the carbon saturation of the alloy is proved to be an essential condition for a proper phase separation. The results showed that FeS mixed with Na2S, ZnS containing sludge and pyrite are effective sulphide systems for copper removal with a removal efficiency of 92% by using pyrite and 95% by zinc sludge at a S/Cu ratio of around 7 times of the stoichiometry. The copper content drops from 12 wt% to about 2 wt%. However, it is still difficult to remove copper completely from the alloy in a single step, and a multi-step operation is needed. The present research is expected to contribute both to the utilization of the metal recovered from bottom ash, and to the general recycling of steel scrap where copper removal from the steel scrap is a critical issue.

Jan 1, 2014

By Gökçe Törenli, Okay Tutar

"Predicting the performance of plant-scale comminution circuits is essential to monitor the energy use and product size distribution, allowing us to control and optimize the whole process. In the light of this issue, with the assist of recent technologies, simulation techniques utilize the chance of putting the theory into practice in the most accurate way. For this purpose, this study aims to evaluate and optimize the efficiency of a plant-scale ball mill circuit by using perfect-mixing ball mill model on a simulation environment. The comminution circuit is selected from a specific copper-ore processing plant in Turkey. The essential parameters which are required for this study such as fresh feed Bond work index, size distribution etc. are determined by laboratory experiments. The forecasted data which are calculated by third-party software will be compared by the industrial operating data, in order to determine the performance of comminution circuit. In addition to that, this methodology provides a greater ability to analyse, optimize and understand the comminution circuit of ore treatment plant. The authors believe this work will provide supplementary data for further studies on simulation and subsequent optimization of comminution circuits.INTRODUCTION By the assist of mathematical models of the grinding mills and classifiers, simulation of the grinding circuits become more common in comminution because it is relatively economical and able to consider many variables simultaneously. It’s proceeds depends on the accuracy of the models and capability of reflect real operations. Computer-based simulation studies would provide the quantified information about the effects of the proposed changes on the comminution circuit performance in terms of size distribution, mass flow rates, equipment efficiency etc. Then the mentioned data used in order to check the suitability of the current equipment to the modified conditions, and for equipment selection. The outputs of circuit could also be used to estimate downstream flotation circuit performance because the general aim in this study is to The aim of the study is to investigate optimum operating variables and achieve p(80) size of 57 µm and 64 % of -36 µm particle in hydrocyclone overflow stream, which is optimum for that porphyritic copper ore for best concentrate recovery after flotation process in specific copper ore comminution circuit by using modelling and simulation techniques. Sampling survey was carried on the fine ore bin in order to perform Bond work index test and determine work index value (Wi). Thereafter mass balancing, using the size distribution data and tonnages, models for ball mills and hydrocyclone were developed. Finally, the circuit performance were investigated by computer simulations via JKSimMet software."

Jan 1, 2018

By G. Unland

The sizing of crushers depends on the expected crushing forces. However, the crushing forces develop differently with every individual rock while it is compressed by the working surfaces of the crusher. For sizing, this compression process has to be characterized by the maximum crushing force. The maximum crushing force depends on the strength, shape and size of the rock, the amount and velocity of the imposed displacement of the working surfaces of the crusher on the rock and the conditions of the contact surfaces. From experience it is known that the strength of the material and, therefore, the crushing forces depend on the size of the specimen. This dependence is the so called size effect. The determination is based on compression tests. The force development is recorded during the compression of the specimen and for every individual test the maximum force is determined. The occurring maximum crushing forces of several rocks with the same diameter comminuted under the same conditions can be assessed by a mean value and a variance. The relationship between the mean values of the cross section related maximum crushing forces FAmax and the corresponding sizes d of the specimens can then be described by mathematical functions. They are derived from different approaches (phenomenological, statistical and statistical-physical methods). The phenomenological methods are subjective and yield functions depending on the assumptions of a person, whereas the statistical and statistical-physical methods are based on an evaluated function and the optimization of the parameters.

Jan 1, 2014

During incineration of municipal solid waste (MSW), some heavy metals and other environmentally harmful elements are liberated into bottom ash. The stricter environmental regulations require a higher immobilization efficiency of the ash before its safe disposal and application. Vitrification is one of the promising options, and has the advantages of high destruction efficiency of organics, high immobilization of heavy metals, and large volume reduction. The main components of the vitrified slag are SiO2, CaO, Al2O3, Fe2O3, Na2O and MgO, and the compositions have direct effect on the glass formation during vitrification, and further on the physical and mechanical properties of the slag. To provide essential data for the utilization of bottom ash as vitrified slag, the phase relations and thermodynamic properties of the oxide system need to be systematically investigated. In the present study, the liquidus temperature of the typical vitrified bottom ash slag was determined by using differential scanning calorimetry (DSC) measurement. High temperature equilibrium experiments were conducted to investigate the phase relations of the sub oxide system of CaO-SiO2-Na2O by means of Scanning Electron Microscopy (SEM), Electron Microprobe Analysis (EMPA) and X-ray Diffraction (XRD). The results show that the melting temperature of the vitrified bottom ash is around 930°C. In the CaO-SiO2-Na2O system with less than 50 mol% SiO2, the liquidus temperature de-creases with increasing amounts of Na2O along the tie-line of Na2O-Ca3Si2O7. Two compounds Na2Ca3Si2O8 and Na4Ca8Si5O20 are identified in the oxide system.

Jan 1, 2014

By N. Johnson, J. Quinteros

With the general trend across all commodities towards the treatment of lower grade ores, it is becoming increasingly important to develop efficient protocols for comprehensive mineralogical characterisation to allow the development of the most appropriate strategies for processing an ore. In the case of silver, there are more than 200 known silver bearing minerals which can make it challenging to identify them. Knowledge of the deportment of silver within an ore is one of the factors used to determine an appropriate processing strategy. Automated SEM-based tools are commonly used for mineralogical characterisation but the low-grade together with the large number of minerals that are potential hosts for silver means that often, complementary analytical tools must be used in order to properly account for the silver. The work presented in this paper is a demonstration of the approach that should be taken when identifying the deportment of silver in complex ores. Three complex, low-grade silver ores were characterised using the approach. The insights from the mineralogical characterisation were then used to inform the metallurgical testing that was undertaken. The results from the batch flotation testing clearly demonstrate the importance of understanding the mineralogy in order to select the most appropriate metallurgical processes.

Jan 1, 2014

By T. A. Penzov

As a result of recent scientific and experimental studies new technical devices have been developed for monitoring and control the process of grinding. The description of microprocessor module MILLCONT 1 for control of the loading of the mill and microprocessor density control module DENSIMETER is given in the paper. The improved variant of the automatic system for ore grinding control in single-stage ball mill working in close cycle with a classifier with above mentioned technical means is shown in the paper. The loops for measuring and stabilization of the basic technological parameters (density of the ready pulp ? and fineness of grinding of the pulp ß) are described in the paper. The nowadays economic results in ore grinding process automation are given as well.

Jan 1, 2014

By Q. Huo

The alumina production might not continue when the sulfur content of bauxite was too high. In order to bring down the sulfur content in bauxite, we studied on the bauxite desulfurization by bacteria screened from the acid mine drainage at mines of high sulfur content. The screened bacteria were domesticated by the high sulfur content bauxite. The experiments of bauxite desulfurization were carried out under the conditions of 5% pulp density, temperature of 30?, rotate speed of 120rpm. Bacterial desulfurization for 30 days, the sulfur content of the bauxite was reduced from 5.73% to 1.55% and the desulfurization percent was 72.9%. The recovery percent of alumina was 94.3%. The study showed that it was feasible to bring down the sulfur content of bauxite by bioleaching and this technique might make full use of the low grade bauxite.

Jan 1, 2014

By V. V. Lodeischikov

This paper covers some problems of treatment of complex gold ores and concentrates containing copper, lead, zinc, antimony and uranium. All these metals may present in ores both as major and associated components. The paper suggests recommendations for early determination of relative value of the metals in ores, which largely contribute to the selection of concentration and metallurgical flow sheets. The focus of this work is on treatment of complex ores in gold plants. The metal extraction technologies used by such gold plants are typically aimed at maximum gold recovery. Therefore, production of base metals as by-products requires significant updating of the existing process flow sheets based on economic, environmental and other considerations. At the same time, cooperation between gold plants and base-metal plants is of great importance. This paper provides an overview of worldwide existing and innovative processes of base metals extraction from complex and refractory gold ores.

Jan 1, 2014

By A. D. Shuloyakov, G. A. Finkelstein, V. I. Kurets, A. K. Vedin

"In disintegrating solid ores with mineral values disseminated in them, one of the principal tasks is to selectively separate valuable mineral particles from the matrix in which they reside, striving at the same time to keep their natural shape and size as intact as possible.The conventional mechanical disintegration methods do not meet this most important requirement in full. The other major objective here is to reduce electric power consumption during the fragmentation stage, since up to 65 per cent of the total power consumption at concentrators processing ores of non-ferrous, ferrous, rare, and precious metals is spent on disintegration steps.Numerous experiments conducted on dozens of ore types (tin, tungsten, and many others, as well as on rock containing diamonds, rubies, emeralds, etc.) have invariably demonstrated by far superior integrity of mineral values as compared with that obtained by mechanical as well as other types of disintegration.However, the process remains as power-intensive as ever which is due to the imperfect nature of the electro-technical devices that convert the network electric current into high-voltage electric impulses responsible for the disintegration process.The maximum capacity attained in disintegrating the hardest materials from 40 mm to 2 mm size in a single operating chamber with four high-voltage electrodes does not exceed 1.0-1.5 t/h. Attempts at increasing the number of electrodes and the capacity of the operating chamber have failed so far because of high overall dimensions and mass of the electrical part of the installation supplying the chamber with pulsating current, as well as of the commutation requirements. At the same time, a number of overseas operations have reported a significant breakthrough in their attempts to reduce dozens of times the overall dimensions and mass of the discharge impulse generating installation (EIS), which enables us to contemplate to increase the capacity of the EIS at least ten times in the nearest future. Yet, even with the currently achieved capacity of the EIS, these installations have found wide use in geological surveying, precious and semi-precious stones production, in grinding super hard materials, etc., since they provide spectacular selectivity of disintegration and thus the integrity of valuable mineral crystals."

Jan 1, 2003

By F. C. Yi

Discontinuous and consecutive process was applied to probe into the Kinetics and adsorption theory for Cs+ adsorbed by Zeolites under the conditions of temperature, time and fixed-bed dynamic adsorption. It indicated that the sorption kinetics behavior of zeolite?s sorption on Cs+ is ac-cord with pseudo-secondary velocity equation, velocity constant k2=0.0005213 g?mg min-1, and equilibrium adsorptive capacity is 147.0588 mg?g-1; The equation can be expressed as: Y=0.0068X+0.0887; From the analyzing of diffusion coefficients on different temperatures and times, the coefficient of diffusion is not only related with the fabric of mineral and the character of ions but also the temperature and time; When the ambient temperature hoisted, the diffusion velocity augmented rapidly; Cs+ would get over a certain energy barrier when it enters into structure of zeo-lite; This energy is expressed by activation energy, and its value is E=131.668818 kJ?mol-1; There are two dominating adsorption mechanisms in the system of zeolite absorb Cs+: ionic interchange and surface coordinate adsorption.

Jan 1, 2014

By Olgac Kangal, Ali Guney, Gulay Bulut, Guven Onal, Ayhan A. Sirkeci

"This paper presents the results of pilot scale column flotation applications in the two different copper concentrators in Turkey. The Kure Copper Plant is located in the Black Sea Region of Turkey. There are four types of copper ore formations in the Küre region. The so called disseminated ore contains 60-70% siliceous minerals of which Cu content is around 0.5%. The remaining three ore types in the region are generally named “massive ores”. The massive ores may assay up to 15% Cu and the major gangue mineral is pyrite associated with relatively little amount of silica. The main copper mineral in all formations is chalcopyrite that is generally finely disseminated in pyrite therefore satisfactory liberation requires ultrafine grinding especially in the case of the massive ores.A blend of these ores, containing 1.7% Cu on average, is fed to the Küre Copper Concentrator whose capacity is 1.2 million tons of ore annually. Unfortunately, today the plant operates below its designed capacity treating around 550,000 tons of ore per year. The design of Küre Copper Plant was undertaken by the Outokumpu Company of Finland. The operation of the plant is almost automatically controlled and the feed, the concentrate and the tailings are assayed for copper by on-line XRF analysers. The particle size analysers are also connected to the grinding circuit. The feed material is ground almost below 50 µm and the flotation is conducted around pH 11.2 using Hostaflot X-231 (a trade mark of Hoechst) as the collector. Apart from the rougher cells, there are four cleaning stages after which the final concentrate is produced. A very fine grinding requirement for an adequate level of liberation makes successful flotation difficult and consequently the final concentrate can hardly assay above 16% Cu leading to copper losses around 20% in the tailings that contains 0.3% copper."

Jan 1, 2003

By L. Y. Zhang

The metallic sulphides in Jinchuan Mine are relative friable and the gangue minerals suffer of wide secondary change, the overgrinding of metallic sulphides and sliming of gangue minerals are the main cause that makes the mineral separation indexes difficult to improve. So changing the process of grinding, and classification, and optimizing the particle size distribution of grinding product is the key improving the separation performance of Jinchuan nickel and copper ore.

Jan 1, 2014

By Aubrey Mainza, Malcolm S. Powell

"A hydrocyclone with two vortex finders, named the three-product cyclone (3PC), has been successfully tested in the Platinum industry for dealing with the dense Chromite found in UG2 ores. This dense component preferentially reports to the cyclone underflow, resulting in an over-ground fine Chromite component in the final product. The dense media effect caused by a high concentration of this in the cyclone feed produces a coarsening of the cyclone overflow, which results in loss of recovery through over-size silica in the PGM carrying component material in the float feed. The fine barren particles of Chromite that report to the overflow are recovered through entrainment in the flotation process, resulting in detrimental contamination of the slag produced from the concentrate.Data from many industrial scale tests of the 3PC have shown that three distinct products are obtained when the inner vortex finder length (LIVF) is extended to the region either above (normal classification) or below (reverse classification) the transition zone (a region were the inner and outer overflow streams are identical). Due to wear problems arising from extending the IVF deep into the cone of the cyclone, it is advantageous to use the shorter IVF. Only the normal classification results are reported here, but similar outcomes (to opposite overflow streams) were obtained for the reverse classification. The results showed notable differences in the percentage split of the plus 100µm material in the product streams, confirming that three distinct products are discharged from the 3PC. About 12% of the plus 100µm material in the feed reports to the middlings stream, 1% reports to the final product, and the remainder to the cyclone underflow.Results of silica and chrome splits to the three distinct products namely, the inner overflow (INO), the outer overflow (OUO) and the underflow (U/F) are given in Table 1. These show that the 3PC can be used to recover coarse silica through screening the middlings product - which has a high silica content. When the vortex finder ratios (ratio’s of cross-sectional areas) are carefully selected, the split of plus 100µm silica to the middlings product ranged from 2.9 to 9.6%. Large amounts of oversize silica and chrome report to cyclone underflow, explaining their high percentages in the underflow stream."

Jan 1, 2003

By C. Çelik

Nowadays the optical sorting of industrial minerals is one of the most important processing methods which has cost efficient production possibilities. This method is used for industrial and raw materials that have different colour and brightness features. Initially this technology is used for sorting of foodstuffs and recovered glass, but for a long time also as physical mineral processing method for both industrial minerals like: limestone, marble, talc, basalt, flint, quartz and secondary raw materials like: building rubble, refractory materials, glass, plastic and household waste. In this study via optical sorting the separation of quartz out of a flint mix, which consists of the particles with different colors and brightness, is aimed. Experiments are performed on an optical sorting machine named CombiSense® 1200 at the institute of ?Aufbereitung mineralischer Rohs-toffe? RWTH Aachen. This automatic picking device was developed by the company ?Separation Systems Engineering (SSE), Wedel?. Hand picking method is used for product analysis and the efficiency tables are prepared on every step accordingly. This process enables to reach quartz products with purity up to 100%.

Jan 1, 2014

By Chen Jianhua, Shen Zhenchang, Zhang Ming, Chen Feifei

"With flotation cells scale-up, the performance of flotation cells is increasingly variated for short-coming and dead zones existing. The residence time distribution which shows the movement of tracers can assess the unexpected flows such as short circuit and dead zone in a flotation cell. In this paper, the residence time distribution of pilot flotation cell is investigated with CFD simulation. Based on the theoretical model, the short-coming probability and dead zone probability are quantitative. The ideal average residence time is similar with the actual average residence time. The mixing effect of the flotation cell approaches the ideal continuous stirred tank reactor. The operating parameters such as speed and feed velocity have complicated influence on residence time distribution. The research would be helpful to understanding flow in flotation cell and improving performances of flotation cell.INTRODUCTIONFroth flotation is a method which purifies minerals according to difference of physical and chemical surface characters of different mineral particles (Shen, Z., Chen J, 2012). Flotation cell is a key equipment for froth flotation method. The flotation cell performances have great influences on flotation index.It is difficult to evaluate flotation cell how to improve flotation procedure to complexity.The main flotation cell performances are aeration volume, air dispersion, solid suspension and residence time distribution, etc (Shen, Z., Lu, S., 2008). Residence time distribution is an important fluid hydrodynamics which could reveal the flow of pulp, mixing of particles and air bubbles. In the flotation cell, the ideal average residence time of pulp could obtain easily. But the fluid differential units would be different flow paths. The residence time of the fluid differential units is variation and would be longer or less than the average residence time. The residence time distribution would reveal the mixing effect and predict the not ideal flow in the flotation cell such as shorting cutting, dead zone, etc. As we know, the shorting cutting and dead zone would be decreased the real flotation time and it is disadvantage to better flotation effect, especially for large flotation cell. It is impossible to eliminate the not ideal flow totally. It is very important to reveal and decrease the shorting cutting and dead zone probability in the flotation cell."

Jan 1, 2018

By Chen Jianhua, Shen Zhenchang, Zhang Ming, Chen Feifei

"With flotation cells scale-up, the performance of flotation cells is increasingly variated for short-coming and dead zones existing. The residence time distribution which shows the movement of tracers can assess the unexpected flows such as short circuit and dead zone in a flotation cell. In this paper, the residence time distribution of pilot flotation cell is investigated with CFD simulation. Based on the theoretical model, the short-coming probability and dead zone probability are quantitative. The ideal average residence time is similar with the actual average residence time. The mixing effect of the flotation cell approaches the ideal continuous stirred tank reactor. The operating parameters such as speed and feed velocity have complicated influence on residence time distribution. The research would be helpful to understanding flow in flotation cell and improving performances of flotation cell.INTRODUCTION Froth flotation is a method which purifies minerals according to difference of physical and chemical surface characters of different mineral particles (Shen, Z., Chen J, 2012). Flotation cell is a key equipment for froth flotation method. The flotation cell performances have great influences on flotation index.It is difficult to evaluate flotation cell how to improve flotation procedure to complexity. The main flotation cell performances are aeration volume, air dispersion, solid suspension and residence time distribution, etc (Shen, Z., Lu, S., 2008). Residence time distribution is an important fluid hydrodynamics which could reveal the flow of pulp, mixing of particles and air bubbles. In the flotation cell, the ideal average residence time of pulp could obtain easily. But the fluid differential units would be different flow paths. The residence time of the fluid differential units is variation and would be longer or less than the average residence time. The residence time distribution would reveal the mixing effect and predict the not ideal flow in the flotation cell such as shorting cutting, dead zone, etc. As we know, the shorting cutting and dead zone would be decreased the real flotation time and it is disadvantage to better flotation effect, especially for large flotation cell. It is impossible to eliminate the not ideal flow totally. It is very important to reveal and decrease the shorting cutting and dead zone probability in the flotation cell."

Jan 1, 2018

By Carlos Collado, Oscar Jimenez, Francisco Diaz, Rodrigo Bernal, Carmen Salinas

Water is a strategic resource for the mining industry. The rising cost has forced the industry to become more efficient in their use, reduce and recycle waste as much as possible. The importance of having a reliable water balance is increasingly urgent, because the resource is scarce and vital to the sustainability of human life, animal and ecosystem. Conventional flowmeters can suffer disruptions or failures by corrosion, fouling, presence of elements in the water as acids, salts and suspended solids. Use of radiotracers is advantageous to determine fluid velocities that are transported through pipes, as they are detectable by means of the radiation emitted, the same way for surface flows, such as natural watercourses and drainage from tailings dams, fluorescent tracers are those with the best advantages. For velocity measurements in pipelines a Iodine-131 tracer solution, around 5 mCi was injected into the suction of the pumps. The technique used is the transit time between detectors at known distances and determining the time of passage of the radiotracer. For measurements of surface fluxes using the fluorescent tracer Rhodamine WT by tracer dilution technique, injecting the tracer at a constant rate and measuring it known concentration diluted downstream. This work has been performed in Minera Los Pelambres, located in the IV Region of Chile, measuring the flow rate pumped from 12 pools with 1-7 pumps operating, obtaining speeds of 0.56 to 2.62 m/s. In pumping wells three facilities have been measured at speeds of 0.111-0.223 m/s, plus six surface flows with flow rates of 8.45 to 357.2 L/s.

Jan 1, 2014

By Güven Önal, Zeki Dogan, Neset Acarkan

In this study, it was aimed to produce glass sand with less than 0.15% Fe2O3 for window glass manufacture and glass ware grade with less than 0.05% Fe2O3 from Yalõköy sand dunes having 0.48% Fe2O3. In order to reduce the iron content of the Yalõköy sand dune, magnetic separation, flotation, scrubbing, H2SO4 leaching and drying were used. The optimum iron removal was achieved by H2SO4 baking at 150oC and 8 kg/t acid consumption. In this way, sand concentrate was obtained with 0.04% Fe2O3 and sand recovery 95%.

Jan 1, 2003