Search Documents

By P. A. Bepswa

A numerical study done to test the efficacy of heuristics developed for the design of measurement networks for high precision metallurgical accounting is presented in this paper. The heuristics considered were designed to maximise variance reduction of terminal stream measurements through data reconciliation for observable linear flow systems. A complex metallurgical process flow sheet from the mineral sands industry was used as a case study. Monte Carlo type simulations coupled with a non-linear programming based steady state data reconciliation algorithm were used as tools to investigate the heuristics. The results obtained suggested a close correlation between magnitudes of measured variances and the respective levels of variance reduction obtained through data reconciliation for both internal and terminal streams. It was observed that variance reduction through data reconciliation was maximised for terminal stream measurements in networks characterised by high precision measurement of internal streams and/or in flow sheets characterised by high ?stream to node ratios?. Terminal streams attached to highly interconnected parent nodes were observed to experience higher reductions in variance compared to terminal streams attached to less interconnected parent nodes. The results generally highlight the additional benefits of highly interconnected flow sheets and high precision internal stream measurement regimes on the maximisation of variance reduction of terminal stream measurements through data reconciliation. These findings are significant to metallurgical accounting and to process accounting applications in general in that they provide a conceptual basis for design decision making regarding the construction of measurement networks aimed at maximising variance reduction of targeted streams through data reconciliation.

Jan 1, 2014

By C. Kleine

Coal sorting with an x-ray-transmission (XRT) sensor has experienced a lot of development since first described by Jekinson et.al. in 1974. Powerful computers and increasingly sensitive X-ray scintillation counters enabled the development of high-performance sensor-based sorting machines. The first industrial installation of a belt-type XRT-sorting for coal is in operation since 2004. It is upgrading high quality coal from 1% ash to 0.7% ash for cathode production. In comparison to the high quality coal which is treated with a belt-type sorter, the chute type sorter has been successfully optimized for high volume coal treatment of lower quality coals. This project was funded by the German Environmental Fund (Project Nr.244444). In cooperation with the RWTH Aachen University and Isambane Processing, CommodasUltrasort(now Tomra Sorting Solutions) conducted extensive pilot test work under production conditions in 2010 for the destoning of power station coal at Arnot Power Station in South Africa. The experience gained during this pilot test phase led to an optimized, redesigned PRO Secondary XRT Chute sorter which is now in operation at a South African coal mine. This flexible semi-mobile modular destoning plant is treating a size range of -120 mm +30 mm at a throughput of 150 tph. The implementation of this plant not only reduces the ash content, abrasiveness index and sulfur content significantly, but also reduces royalties, water treatment and transport costs.

Sep 1, 2012

By H. J. Cao

Valuable elements could be extracted by microorganism ferment fluid from bauxite, which mainly due to bacteria acid namely organic acid. And after leaching, reclaiming the remainder organic acid in leaching solution was an important procedure for bauxite leaching process. the re-searching status about organic acid reclaiming process from bauxite ore bioleaching solution was summarized. Common processes for recycling organic acid from bauxite bioleaching solution in this period and their advantages and disadvantages, research aspects which need being confirmed for the future were Indicated

Jan 1, 2014

By V. Buddhiraju

Liberation of valuable minerals from low-grade ores is an important challenge faced by the minerals industry. It is necessary to grind the ore to extremely fine size in order to liberate the mineral from such ores. As it is generally difficult to produce ultra-fine particles of diameter less than 1-10 mm using traditional grinding equipment such as the ball mill and the rod mill, several new types of grinding equipment are being explored to produce ultra-fine particles. The planetary ball mill is promising in that it makes grinding to submicron sizes possible by imparting high energy to the ground powder. It consists of four pots mounted on a disc. The pots and the disc rotate in opposite directions. The high-speed rotation of the pots and the disc makes the grinding media move at high centrifugal velocities leading to high impact energy and thus improving the grinding performance. The planetary mill is currently being explored for its capability to produce ultra-fine particles on a large scale. In this context, there is a need to understand the dynamics of the ultra-fine grinding process within the planetary ball mill. Here, we address this need by studying the movement of media inside the pots and the grinding kinetics, employing both experimental and modeling techniques. The experiments were conducted on a laboratory scale planetary ball mill. The particle size distribution of the powder was monitored to allow an estimate of the grinding kinetics to be made while video images of the media profiles inside the pots were taken to allow quantification of the media movement as a function of process variables such as the media size, percent loading, etc. The population balance modeling (PBM) framework was used to simulate the kinetics of grinding while the discrete element modeling (DEM) approach was utilized to simulate the media motion. The parameters in the population balance model, namely, the specific breakage rate and the breakage distribution function were determined by fitting the batch grinding equation to the experimental data. The predicted powder size distributions were found to be in good agreement with the experimental data. The experimental results have shown that the mean size of product powder decreases as the size of the grinding media decreases. Keywords: population balance modeling, grinding, planetary mill, grinding media, grinding equation

Sep 1, 2012

By Jacob Masliyah, Zhenghe Xu, Lujie Yan

"Understanding adsorption mechanism of polymeric organic process modifierssuch as carboxymethyl cellulose (CMC) on talc hasbeen a major challenge due to anisotropic nature of talc basal planes and edge surfaces. The main objective of this study is to investigate the adsorption of CMC on the basal planes and edge surfaces of talc.Smooth basal plane and edge surfaces of talc were prepared successfully by simple cleavage and sophisticated ultramicrotome cutting method, respectively. The prepared surfaces were characterized by atomic force microscope (AFM) imaging to be sufficiently smooth for colloidal probe force measurements using AFM. Anisotropic surface charge characteristics were determined,with the basal planes to carry a permanent negative surface charge and edge surfaces featuring a pH-dependent charge characteristic. The adsorption of CMC on talc basal plane and edge surfaces at pH 9 in KClaqueous solutions of various ionic strengths wasinvestigated by in situ AFM imaging technique. Themorphology of adsorbed CMC on talc basal planes and edge surfaces was found to be significantly different, due to different binding mechanisms involved. Interaction of CMC with the talc basal plane was found to bedominated by hydrophobic interactions while its binding with the talc edge surface was mainly through chemical complexation and hydrogen bond. The amount of CMC adsorbed on both talc basal planes and edge surfaces increased with increasing ionic strengthof solutions. The methodology developed in our study opens the door to probe polymer adsorption on anisotropic phyllosilicate surfaces, which can help us better understand the mechanism of polymer adsorption on specific mineral faces."

Jan 1, 2014

By Majid Saghaeian, Rasool Hejazi, Parisa Ghobadi

"Pulp handling in mineral processing circuits is very complicated due to its inherent different specifications compared with other fluids such as water. Because any variation in ore property (e.g. size and abrasion index) and pulp specification (e.g. density, solid content and pressure) causes problem in this part and reduces the plant availability and throughput as a result. The most common issues in the hose system are sumps and pipe-line blockage, wearing of the pumps impeller and liner, and pipe tearing specially at elbows and bends. High pressure grinding roll (HPGR) is employed in a closed circuit with a screen as the first stage of grinding in Zarand Iranian Steel Complex (ZISCO). Wearing of the pump and pipeline transferring the screen undersize stream was the main problem from the plant commissioning. The plant couldn't achieve to the design capacity because of this defect. Although various practical solutions such as improving the pipes and impeller material quality and eliminating the elbows, as much as possible, were done in order to downtime minimizing, but damages didn’t vanish. Since HPGR discharge contains somewhat rough and abrasive particles, the mentioned modifications didn't effective very much. Therefore, converting of the wet screen to dry and using of belt conveyor to the screen undersize handling was employed based on the plant capability evaluation and experimental and pilot trial results. Although this reformation imposed another additional cost (for conveyor system), but it had significant advantages such as increasing the plant availability up to 96%, reducing the operating costs of the wear parts, providing more stable operating condition for the HPGR performance and decreasing abrasion rate of the HPGR rolls liner because of the lower moist feed."

Jan 1, 2014

By S. V. Bogdanov, S. I. Grishaev

"The article presents the materials about the appropriateness of the use of rental indices to assess the effectiveness of the use of deposits of rare earth elements (REE). The authors suggest from the standpoint of rent payments to rate for the owner the possibility of using the anticipated rental income as the indicator for the analysis of preferences and economic significance of enrichment of extracted raw materials in the emerging field of rare earth metals (REE). Usually from ore mined at the fields, for flotation technology to produce concentrates with collective REE, then they are subjected to chemical-metallurgical processing of the received products are divided into pure oxides, chemical compounds or isolated from them pure metals and alloys. This commercial product is shipped to the buyer. REE were a non-renewable natural resources, so the calculations for determining differential and specific rent showed that during the development of the technologies of mineral processing of a specific field it is necessary to consider what the expected rental income depends on the magnitude of differential rent is related to the volume of production of REE for the whole planned period of exploitation of natural resources. This income is determined by the amount of stock field. For long-term exploitation of the deposit is observed in almost direct proportional dependence between the annual differential rent and the rental income. The decrease in rents in the long run is determined by the change in the composition of ores included in the extracted raw materials and the balance between light and heavy REE. The largest 70% reduction of the rent projected for ""cerium"" fields, while for ""yttrium"" these losses are considerably smaller. Tomtor, Chuktukon and Katuginskoye Russian deposits are characterized by a level of rent that is comparable to the mastered foreign sources of REE. Thus, the enrichment of minerals with REM in the domestic deposits is quite competitive at the world level. INTRODUCTION Deposits of rare earth metals (REE) are non-renewable resources that should be developed and used so that it would be possible to provide a reduction due to payment of appropriate resources for future generations. This compensation, due to the reduction of natural resources, can be carried out both in natural and in economic terms (1). When analyzing economic compensation options, particular attention should be paid to rental income in assessing the attractiveness of using different REE deposits. It is known that absolute and differential rents are summands when calculating the value of natural rents. The value of the absolute natural rent is proportional to the unit price of the product obtained from mineral raw materials and sold on the commodity market. Limitations, as well as the use in production processes and business, contribute to the gradual reduction of natural resources, which increases their consumer value and affects the price of commodity products from primary raw materials."

Jan 1, 2018

By X. W. Zhang

Mica plate is broadly used in electric industry, production of man-made mica paper plate is in-creasing. The problem coming with is that large quantities of leftover materials unable to be re-cycled are produced during cutting and molding of mica plate productions. The leftover materials are always abandoned as crabs, which not only pollute the environment but also waste our resources. The study intends to find a new measure to decompose and to reuse the mica plate leftover materials so as to create a new production process of mica plate, which is clean and does not produce crabs.

Jan 1, 2014

By Mario Gerards

Maturing populations create an increase in the demand for the type of non-ferrous metals, which are used in the manufacturing of electronic products. The depletion of existing high-grade deposits, make it necessary to boost the efficiency of beneficiation processes and most importantly the yield (recovery rate of the value commodities). Increasing demand now makes it worthwhile to tap into resources, which were previously considered waste, for example secondary deposits such as tailing ponds and electronic waste. In order to achieve increased yields, increasingly finer, or even ultra-fine fractions have to be treated. In most cases, mineral characteristics such as size and density call for non-mechanical, high-capacity technologies to be used. There are various technologies that allow for the separation of fines and ultra-fines. This paper outlines the dynamics and efficiency of pneumatic flotation with emphasis on its application to the recovery of non-ferrous metals, from electronic waste. The conventional agitator flotation technology of an electronic waste processing plant was not able to recover ultra-fine non-ferrous metals satisfactorily, due to losses within the tailings. Because of its adaptability and its inherent suitability for non-ferrous metals, pneumatic flotation has been incorporated to the existing process achieving excellent results. The merit of the process lies in the state of the art technology, which does not utilize compressed air and any rotating parts, which results in a reduction in wear and energy requirement, both features of this innovative technology. In addition, the use of pneumatic flotation resulted in a significant reduction in residence time, when compared to mechanical flotation. Pneumatic technology is able to influence air bubble size in a flotation cell, by changing the speed and pressure of the slurry stream. Higher slurry velocities lead to the formation of smaller air bubbles, which is required for the successful flotation of ultra-fine particles. Conversely, decreasing the slurry velocity leads to bigger air bubbles. The optimum bubble size can be created according to different feed characteristics. This is important in case of feed fluctuations.

Sep 1, 2012

By Liang Dianyin

In this paper, the molybdenite flotation tailing of cleaner-scavenger bank which has a mass of very fine particles has been taken as raw ore to be processed by flotation with/without ultrasonic. The effect of ultrasonic frequency, intensity, processing time and uploading location on molybdenite flotation efficiency is investigated by four-factor three-level orthogonal experiment, and the effect significances of these ultrasonic variables to molybdenite flotation efficiency have also been evaluated. Single-factor analysis of variance is conducted to investigate whether the effect of ultrasonic on molybdenum ore flotation efficiency is significant or not. The samples extracted from different ore species in different time have been mixed to analyze the particle size. The results show that the particle size of +38µm in concentrate obviously increases while the particle size of -25µmobviouslydecreaseswith ultrasonic, which means that ultrasonic is good for flotation due to sludge removing effect. Keywords: ultrasonic, flotation efficiency, sulfide ore, tailing, grade, sludge removing

Sep 1, 2012

By S. M. Mustakim

Red mud is the major waste material produced during digestion of bauxite ores with caustic soda in alumina production following the Bayer?s process. Its disposal remains a worldwide issue in terms of environmental concerns. A lot of research and developmental activities are going on throughout the world to find effective utilization of red mud, which involves various product developments. At present, building materials, industries are fast growing industrial sector where the need of various raw materials is enormous. The use of red mud in building material production is one of the options for conservation of natural resources and reduction of environmental pollution. A cost-effective and energy efficient mineral cementation process has been developed at CSIR-IMMT, Bhubaneswar for use of red mud in manufacture of building brick, block and aggregate. The red mud is an alkaline material, which contains both leachable and non-leachable soda along with different mineral constituents of alumina, iron and silica. The effort has been made to use the mineral constituents of red mud to develop cold setting building brick by mineral cementation process using a binder specially prepared from Portland Slag Cement, Lime, Gypsum and Alkali metal sulfates. The red mud has been used from 40 to 70% by weight along with fly ash and binder in development of cold setting building brick conforming to the specification of IS:12894:2002.

Sep 1, 2012

By I. Kairyakov

The present paper is about the restoration of the molybdenum production in the floatation plant of Ellatzite-Med AD in Bulgaria. The process, based on a working design, includes the construction of a new floatation molybdenum section in the existing molybdenum department of the Floatation Plant using the so called Vemco inert-gas floatation machines, made especially for the molybdenum floatation. While in the ordinary floatation machines, block impellers create suspension of the air, sucked from the atmosphere with the slime particles of the concentrate, which creates conditions for oxidizing the reagent, Vemco inert-gas floatation machines are covered with hermetic lids and the air inside the chamber is used. The technology, suggested by Geotechkoper Ltd. for making the working project, employs special machines from Dor Olliver Aimco, suitable specifically for molybdenum floatation in order to reduce the oxidizing of the reagent sodium hydrosulphate. Also the transport of the chamber product is done in hermetic conditions as the molybdenum flotation is done in two floatation rows and refining operations 3 to 8 are placed in the second row. Thus in the basic molybdenum floatation together with the first and second refining operations, which are hermetically closed, an ambient condition with low content of oxygen is created, that is about 8% for oxygen and about 92% of nitrogen, in which the oxidizing process is extremely reduced. This in turn results in reducing the consumption of the reagent depressor ? sodium hydrosulphate. In that way there is an improvement of the economical indices of the molybdenum production.

Jan 1, 2014

By J. Y. Xu

A mutant of Phanerochaete chrysosporium, which is capable of degrading lignin, was bred by ul-traviolet ray irradiation and this mutant strain shows high capability of degrading of lignite. The degradation ratio of original Yima lignite and nitric acid treated Yima lignite by this mutant are 37.6% and 51.62%respectively, whereas those by the original strain are 31.84% and 32.55% respectively. XRD and FTIR analyses of the lignite converted product show that its polymerization degree and average molecular weight are both greatly reduced. The content of the functional groups is also been altered.

Jan 1, 2014

The flotation efficiency of magnetic concentrate of the Anhui hematite ore, which includes a great quantity of iron-bearing silicates, has been studied through reverse flotation test with a new type of collector Fly-102. The results indicate that collector Fly-102 has a strong adaptability to the variation of temperature, when the flotation temperature is in the range of 10? to 35?, using collector Fly-102 can obtain good flotation indexes. Collector Fly-102 has a strong adaptability to the variation of the slime contents and grades of the flotation samples. When the content of slime and the grade of the flotation feeds are 30% and 55.63% respectively, under the condition that the temperature is 15?, the open circuit flotation test was carried out with collector Fly-102. After one-stage roughing, one-stage cleaning and two-stage scavenging, a better result is got, the grade of iron concentrate reaches 67.12%, and the recovery of iron concentrate comes up to 84.15%.

Sep 1, 2012

By P. Raghavan1

Reverse froth flotation experiments were carried out in the laboratory using two different types of kaolins for the separation and removal of coloring titanoferrous impurities from cryo-filtered clay after subjecting to high shear pre-treatment. This high shear pre-treatment consists of high shear agitation of a high solids clay slurry with the dispersant (high shear dispersion, HSD) followed by high shear agitation with the collector (high shear conditioning, HSC). After this pretreatment, the slurry is diluted and reverse flotation is carried out. One sample is from, Gujarat, India (Mamuara clay, ?MC?) while the 2nd sample is from Amberg, Germany (AKW clay, ?AC?). While MC consisted of 89% particles below 2µm and analyzed 1.06% of TiO2 and 0.29% Fe2O3 and measured a brightness of 83.4 %ISO, the corresponding values for AC are 67% below 2µm, 0.3% of TiO2? 0.49% Fe2O3 and 83.4 %ISO. The flotation performance is found to be greatly influenced by the conditions of high shear treatment. Important variables are HSD intensity (rpm), HSD time, HSC intensity (rpm), HSC time, HSD/HSC time ratio, ?HSD+HSC? total time etc. Higher shear intensities favor both the impurity liberation and collection. For both clays, it could be shown that impurity removal increases as total pretreatment time (?HSD +HSC? total time) increases up to a certain limit. For MC, the HSD time was only half or less than that of HSC time, while for AC, HSD time is at least twice (or more) than HSC time which is just an opposite manifestation. This is believed to be due to the striking differences between these two clays. Most importantly, the shear frequency is found more influential than the shear rate for the overall flotation performance for both clays. Interestingly, at high shear frequencies, i.e., when a stirrer with more number of teeth on the rotor is used, the ?HSD+HSC? total time is greatly reduced. Again, increased shear frequency helps to reduce flotation time and significantly improves flotation performance. At optimum conditions, product titania reduced to 0.35% for MC whereas the same reduced to 0.13% for AC. The product of flotation of MC measured 85%ISO brightness while that of AC measured84.6%ISO thus enhancing the value of the final product. It could also be established that the high shear pre-treatment shows better flotation performance than that due to collector dosage. Keywords: high shear dispersion, high shear conditioning, titanoferrous impurities, shear rate, shear frequency, brightness, clay recovery, Mamuara clay, AKW clay

Sep 1, 2012

By S. H. Morar

Froth stability is widely recognized as a key driver of flotation selectivity. It is well known that froth stability is affected by the type and quantity of surface active reagents present (frothers), and the concentration and hydrophobicity of solid particles present. While some studies have been performed on the effect of frothers on froth stability in three-phase systems and the hydrophobicity of particles present, very little work has been performed on the effect of solids loading on froth stability. This may be due to insufficiently robust measurement techniques. This paper investigates the use of a new machine vision measurement to measure solids loading, and the relationship between this measurement, bubble size, and bubble burst rate on the froth surface. Keywords: froth flotation, machine vision, solids loading

Sep 1, 2012

This study examines the surface alteration and flotation behaviour of synthetic moncheite, PtPd(BiTe)2, in the presence of pentlandite. The telluride minerals contribute around 20% ~ 30% and up to 45% of the PGM present in the Platreef ore and are considered to be slow floating as there is evidence of these minerals reporting to the tailings. It was proposed that oxidation products from other minerals and grinding media would affect the mineral surface composition and floatability thereby causing inadvertent depression of moncheite due to precipitating ions. ToF-SIMS analyses (time of flight secondary ion mass spectrometry) was used to characterise the mineral surface as well as the extent of surface alteration. Microflotation was used to deter-mine the hydrophobicity of the synthetic minerals. Conditioning of moncheite in the presence of pentlandite reduced the flotation response of the + 38 -106µm size fraction from > 99% to 56%. This was due to pentlandite dissolution products (iron and nickel hydroxy species) which formed overlayers on the mineral surfaces thereby inhibiting the adsorption of collector. In addition, further grinding of these samples, with and without pentlandite conditioning showed a negative effect on recovery due to the fineness of the particle size distribution and there was no advantage gained from any possible exposure of fresh sites in the sample.

Jan 1, 2014

By Saeed Farrokhpay

It is known that the grinding condition has a major effect on the beneficiation characteristics of the minerals in subsequent processing, in particular, flotation. In the flotation process, particles surface and their condition can significantly influence collector adsorption and flotation performance. For example, particle shape and its surface roughness occurred during grinding may influence flotation characteristics of a specific ore. In fact, adsorption of different cationic and anionic species on mineral surfaces can be varied depending on the selected comminution procedure. The flotation performance of sulphide minerals can be detrimentally affected by the surface oxidation. The amount of surface oxidation may reduce the hydrophobicity of the mineral and makes adsorption of collectors less selective. Improved liberation may generally result in improved flotation recovery. However, this may result in finer grinding and slimes, and consequently, reduce the overall flotation recovery. This paper discusses the effect of wet and dry grinding on copper flotation of a complex Cu-Pb-Zn ore. Industrially, wet grinding is preferred due to its higher energy efficiency and owing to downstream processing requirements. In this study, series of flotation tests were conducted,and surface analysis (XPS and ToFSIMS) were performed after wet or dry grinding at two different P80 values. Mineralogical study was also conducted to investigate the liberation of valuable minerals after grinding. A higher copper flotation recovery was found for wet grinding. However, the copper recovery was increased by further grinding in both conditions (wet and dry). The results showed a higher collector adsorption on copper mineral surfaces after wet grinding. The surface analysis also revealed that the ore is slightly more oxidized after dry grinding probably due to higher temperature during dry grinding.

Sep 1, 2012

By Jerzy A. Mielczarski

The separation of albites from quartz by flotation applying the conventional HF-methods is no longer acceptable from an environmental and health point of view. Therefore, the search for a new reagent scheme without using HF depressor for separation of albite from quartz is under consideration. The flotation behaviour of ore mineral components depends on the produced hydrophobic or hydrophilic surface coverage (chemical functionalization). Currently we have excellent possibility of monitoring surface composition and structure at molecular and atomic levels at surfaces of natural minerals contacted with aqueous solutions of collectors, activators, depressants which is vitally important for the understanding of the surface chemistry that govern selective and efficient flotation. Detailed surface characterization of minerals before and after their exposition to different solution conditions was performed by the most modern spectroscopic techniques such as developed by us the infrared external reflection technique combined with spectral simulation and X-ray photoelectron spectroscopy (XPS). It is possible to monitor surface reactions which facilitate the separation process and those which bring disadvantage to selective flotation. At first we found that a small amount of ?mineral impurity? presented in natural ore could play important role in selective hydrophobization process. It was found that the pH of solution (parameter possible to control) and natural mineral impurities present in mineral samples (parameter related to ore origin) play a very important role in the separation process. Another important parameter is interaction between minerals, quartz and albite, present in aqueous solution. The limitation of flotation separation resulting from chemistry will be discussed. Moreover, the most promising scheme for separation of albites from quartz will be examined.

Jan 1, 2014

By Jia Ma, Lu-De Qiang, Zhi-Chao Liu, Chun-Feng Li, Guang Li, Bao-Bin Tang

"At present, research on the surface chemical properties of uranium minerals is very scanty, which restricts the research progress of uranium ore flotation process research. The research aimed at exploring the surface characteristics of two common uranium minerals and providing basis for flotation process to enrich uranium minerals in ore. This paper selected pitchblende and uraninite as the object of study, which are widely distributed in uranium deposits. We chose out the pure minerals of pitchblende and uraninite from different ores collected from different uranium deposits. By means of Zeta potential test and X-ray photoelectron spectroscopy (XPS) test, a preliminary study on surface characteristics of the pure minerals of pitchblende and uraninite was conducted. And the significance of the change of Zeta potential, the elements composition and valence state on the minerals surface for flotation was discussed. The research shows that, the Zeta potentials of pitchblende and uraninite in pure water are negative mainly when the pH value varies from 2 to 11, which maybe a result of the difference of ionization capacity between two kinds of oxy-compounds on the surface of minerals. On the surface of pitchblende and uraninite, the metal elements are mainly U, Th and Pb. U is mainly in the form of UO2, Th is mainly in the form of ThO2, and Pb is mainly in the form of Pb and PbO. Based on the surface characteristics of pitchblende and uraninite, we can select process and reagents appropriately in uranium ore flotation.INTRODUCTION Globally, the major challenges associated with exploitation of low grade ores are about finding economically feasible processes for reducing the mass of gangue minerals (Filippov et al., 2012). Among the beneficiation technologies of low grade uranium ores with complex minerals assemblage, flotation is the common process which is used to reduce production cost and eliminate the acid-consuming minerals (Li et al., 2016; Liu et al., 2015)."

Jan 1, 2018