Search Documents

By R. C. Miranda

Flotation is an operation widely used in mineral processing because of its aptitude to recover minerals of interest very efficiently. Flotation is often responsible for making possible the exploitation of mineral deposits of low concentration. In flotation various processes phenomena occur, some of which have still not been explained scientifically. Due to this fact, there are no models that can be widely applied in flotation control. Thus, in most cases, the control is done by experienced operators who are able to visually classify the types of foam into different categories and each one of them is associated with an operating actuation. In this situation, image analysis is configured as a solution that has already been employed in several ways. In this paper, a control strategy based on the colour of froth on a direct flotation of a nonferrous metal is presented. Moreover, the paper reveals the theoretical basis of the method, the critical points, difficulties and improvements that can be implemented. Data of grade were collected from the mineral of interest and RGB (red, green and blue) data of final concentrate of the froth. The mineral grade was collected and analysed during one month of operation and RGB was obtained using a camera. It was verified that the red colour showed the same trend of the grade curve in the concentrate. Thus, the use of this online data in optimising control was introduced. The laboratory grade is used to calibrate the colour set point. Therefore, it was possible to monitor in real time the trend of enrichment and depletion of a non-ferrous mineral in a flotation. It was possible to establish an online control strategy based on simple data acquisition. The result was an increase of 10% on production.

Sep 1, 2012

By M. P. Krasteva

The froth flotation process for separation of mineral ores depends on the establishment of care-fully controlled froth. The formation of very stable froth in the flotation circuit is a problem that may occur in many plants, resulting in down-time, low quality and grade of final product and considerable expenses. Froths build up on the top surfaces of thickeners, tanks and flotation cells until they overflow, or until the efficiency of the circuit is impaired. A similar problem exists in Assarel concentrator, Assarel-Medet PLC, Bulgaria. Copper and copper-pyrite ores are dressed in Assarel concentrator. They are characterized with variable and complex mineral and physical composition. During the flotation cycle, resilient and difficult to break-down froth is formed, which subsequently impedes the process of thickening and clear overflow obtaining. Due to this problem continuous sampling in the cycle of thickening was conducted. The mineralogical, chemical composition, particle size distribution and solid phase content of the products were determined. It was established that the solid phase of the froth build up on the top surface of the thickener differs considerably from this one of the thickener underflow. The data clearly indicates that a separation process takes place on the top surface of the thickener ? fine particles of chalcopyrite are concentrated in the froth. The role of chemical reagent addition in the break-down of the flotation froth is investigated in terms of surface chemical phenomena involved in the stabilized froths. Measurements of the coper minerals wettability and surface tension at the air/liquid interface were performed. The surface active agent AERODRI® dewatering aids were laboratory tested. Bench-scale froth collapse tests were conducted. Reagent addition into pulp-froth system promotes and leads to a bubble coalescence, an improvement of the wetting of the mineral particles and a decrease of the surface tension at the air/liquid interface. The results of the laboratory experiments showed that the presence of the surface active agent leads to considerably decrease of the froth stability and the destruction of the deleterious froths build up on the top surface of the thickeners in Assarel concentrator.

Jan 1, 2014

By L. Bbosa

Positron Emission Particle Tracking (PEPT) and the Discrete Element Method (DEM) are used to investigate Power Draw in a laboratory scale tumbling mill. The mill is run dry in batch mode at different speeds using mono-size charge of glass beads, and is mounted along with a torque transducer to measure power. Particle tracking information from PEPT is used to reconstruct the motion of glass beads and infer the overall charge behavior, while DEM is employed to simulate particle motion and interaction, with collision mechanics calculated using the Hertz-Mindlin contact model. For PEPT and DEM data, the product of torque and average angular velocities in discrete cells are accumulated to obtain mill power. This method is found to be within statistical agreement with measured power for all tests. Spatial distributions plotted from this approach highlight the regions of the mill that draw the greatest power. A second technique to obtain Power Draw from DEM data which sums particle forces against the mill geometry is similarly found to accurately predict mill power with lower statistical error. Keywords: Power Draw, PEPT, DEM

Sep 1, 2012

By Stoyan Gaydardzhiev, Michel Shengo, Pierre Kalenga

Lab-scale flotation of copper and cobalt oxidized ore from the Luiswishi deposit in the Katanga province (DRC) has been done focusing on the influence of the degree of process water recycling on metals recovery. Results have shown that at 20 % recycling rate, the recovery of copper and cobalt in the cleaner stage have been respectively reduced to 23 % and 45 % in comparison to 53 % Cu and 63 % Co if process water has not been recycled. At 10 % recycling rate however, the system could still tolerate the effect from recycling, since Cu and Co recovery has remained respectively at acceptable levels of 52 % and 60 %. In order to explain the reasons for the observed worsening of flotation results if process water was recycled at rate higher than 20 %, electrochemical investigation of the pulp has been performed. It has been established that the chemical compounds formed in the pulp when process water was recycled, do influence the sulphidization of malachite and heterogenite and impact further collector adsorption. To confirm these assumptions, the effect from thiosulphate ions presence during the sulphidization of high purity malachite has been studied. It has been found, that thiosulphate ions depending on their concentration in water induce variations in pulp properties such as DO content, pH, Es and contribute to formation of undesirable chemical compounds on mineral surface as identified by DRIFT spectroscopy.

Jan 1, 2014

By D. Gucbilmez

Three spiral concentrators having different geometries were compared in a chromite processing plant. They had different diameters, helix-cross sections and capacities. Two of the spiral concentrators were manufactured in China and one of them was manufactured in Australia. The tests were carried out in a closed circuit experimental setup by using a low grade chromite ore. The pulp densities kept the same during the operation, and the samples were taken simultaneously. The effects of the different positions of the splitters on separation and the feed rate were the parameters that were observed during the experiments. The performances of three spiral concentrators were found to be different. To clarify the effect of the particle size on the separation in spiral concentrators, the screening was applied to the feed. The samples were sieved from 75µm. The test results indicated that the separation performance decreased dramatically in very fine particles. Although fine particles caused some problems in spiral concentrators, fine grinding is required for this particular chromite ore for better liberation. A suitable method for the fine particles should be investigated for acceptable recovery.

Sep 1, 2012

By M. McClintock

"High Pressure Grinding Rolls (HPGR) is increasingly being chosen for comminution circuits for its energy-efficiency for hard rock mining operations. Despite HPGR’s growing popularity, geo-metallurgy programs are still prohibitively expensive because of large sample requirements. Traditionally, sizing HPGR application requires a significant amount of sample, in the order of 1 to 10 tonnes, depending on the level of study and complexity of the resource. Therefore, engineering and design of HPGR circuits typically are reliant on few composites that are required to be representative of the resource and mine plan. Three bench scale HPGR test methodologies were developed in 2015 at NBK Institute of Mining Engineering at the University of British Columbia (UBC) capable of defining the energy size breakage relationship of pilot HPGR. These methodologies were developed to allow bench scale testing for different levels of study from PEA (Preliminary Economic Assessment) to detailed design and operations. The Piston Press test defines the energy size reduction relationship by measuring specific energy consumption and corresponding feed and product size distributions. The advantage of Piston Press testing is the small sample requirement of 5 to 10 kg. Small sample requirements allow multiple samples to be tested across a deposit. Piston Press testing allows extensive geo-metallurgy programs that can determine ore variability and inform in optimization and production planning. To date, the Piston Press methodologies have been validated on a pilot-scale HPGR unit located at UBC. Recently, testing was conducted to calibrate and validate the Piston Press test against full-scale HPGR on a gold sulphide ore deposit. The program included the collection of operational data with the respective HPGR feed and recycle sample. Sample collected was used both for Piston Press testing and HPGR piloting. This paper discusses the test-work and results as carried out during this program, using the aforementioned methodologies."

Jan 1, 2018

By J. K. Afidenyo

Microbial pretreatment of a double refractory gold ore was investigated using a white rot fungus, Coriolus versicolor (ATTC 20869) to improve gold extraction. A series of preliminary tests were conducted to determine the amenability of the ore to fungus degradation. Pulp density, temperature, pH and retention times were the process variables considered. Both a single. Stage and two-step processes were studied to establish process conditions. During the single stage process, the ore was contacted with the fungus culture (biotic) for 3weeks at 30°C and pH 10.0. For the two-step process, the first step involves ore contact with the culture medium (abiotic) at 45°C and pH 10.0 followed by fungal contact (biotic) at 30°C. Results indicated that carbonaceous matter is not degraded but passivated by the fungus; as preg-robbing activities dropped significantly from 18.1% to below 1.0%. The single stage process resulted in higher gold recovery than the two-step process Gold ex-traction by cyanidation of the pretreated ore was 78.9% for the single stage compared with 15.0% for the untreated ore. In the two-step process, only 73.3% gold extraction was achieved. Application of the two step process conditions to a high grade flotation concentrate, resulted in 93.3% gold ex-traction as against untreated concentrate of 30.5%. The results show that the microbial pretreatment process degraded sulfide sulfur, passivated carbonaceous matter and enhanced gold extraction from double refractory gold ore and concentrate.

Jan 1, 2014

By G. K. Nimal Subasinghe

The performance of Knelson Concentrators (KC) used in gravity gold circuits often rely on manufacturers recommendations for selecting operating parameters such as, fluidising water flow rate and cycle time. These parameters are not only dependent on the machine parameters but also on the feed characteristics such as, size distribution of the gold and gangue particles and the composition of its constituent minerals. Particles entering a KC experience a centrifugal acceleration due to the high bowl rotational speeds. The required centripetal force to maintain a circular orbit is provided by the fluid drag force created by inwardly moving fluidising water and the Bagnold?s force arising from the particle/particle collisions. When the fluidising water flow rate is low particles move towards the outer rim of the bowl forming a packed bed within the grooves. On the other hand, if the fluidizing water flowrate is high the bed expands and some particles would move towards the centre of the bowl and gets carried to the tailings stream, thereby reducing the amount of material retained within the grooves of the bowl. Based on a force balance on a particle captured within the KC, a criterion which can be used to predict the amount of material recovered in the bowl has been derived and validated by experimental data. It has been shown that this criterion may be used to demarcate the transition of the bed from a packed-bed state to a fluidised state depending on the fluidizing water flowrate. By identifying the conditions for the optimal expansion of the bed comprising different constituent mineral particles, it is possible to estimate the optimal fluidising water flow rate that would maximise gold recovery while minimising gangue recovery. It was also observed that the accumulation of valuable mineral in the bowl takes place by the displacement of the gangue particles in the bed by the incoming heavy mineral particles. The kinetics of this segregation process was also studied using synthetic mineral mixtures. The experimental data suggests that this process follows first order kinetics and that the build up of heavy mineral reaches a maximum which could be used to identify the optimal cycle time. In this work, the suitability of the above model in optimizing the performance of a KC have been reviewed. Also the necessity and merits of testing an unaltered

Jan 1, 2014

To extract the gold from refractory gold concentrate with high sulfur and arsenic, the gold concentrate was catalytically oxidized to expose the gold for cyanide leaching. The effects of reaction temperature, initial nitric acid concentration, reaction time and initial gold concentrate concentration on the conversion rate were studied. The results show that the appropriate conditions for the catalytical oxidation of this gold concentrate are: reaction temperature of 65 oC; initial nitric acid concentration of 25% (wt.); reaction time of 1.5 hours; initial gold concentrate concentration of 10% (wt.). Under such conditions, the conversion rate of gold concentrate is 92%. The solution can be used to prepare nano-iron oxide red pigment. Gases released in the process can be recycled and reused by oxidation absorption. A chemical background of catalytic oxidation is proposed.

Jan 1, 2014

By K. D’Elia, L. D. Ogrel, O. A. Malyshev, T. I. Yushina, I. M. Petrov

"The purpose of this research is to develop enhancements in the mineral processing by flotation methods of nonferrous ores. Currently, 180-190 million tons of ore are processed by flotation in Russia. The annual processing volume of copper-nickel and copper-zinc ores exceeds 20 million tons. In the total volume of processed ores by flotation, non-ferrous ores account for roughly 35% and ores of precious metals for another 15%. The total demand of flotation reagents in Russia in 2016 was estimated at 170,000 tons. Sulfur-based collectors used in the flotation of non-ferrous sulfide ores (typically, xanthates) do not always offer sufficiently high recovery of valuable components.It has been found that reagents like DMIPEC and DK-80 improve the recovery of metals into concentrates. To identify the reasons of that higher recovery, quantum chemical calculations of the mechanism and interaction forces of DMIPEC with non-ferrous sulfides were undertaken by determining the stabilization energy of the resulting chemical complexes. It has been shown that, in the interaction of DMIPEC and DK-80 with the surfaces of sulfide minerals, ethylene and acetylene bonds act as the reaction centers, and the formation of molecular p-complexes is the result of metal-cation interactions with the surface and the flotation reagents.In the flotation of non-ferrous ores, DMIPEC and DK-80 act as selective supplementary collectors with foaming properties, and at a flow rate of 3-35 g/ton, they reduce the flotation time, and increase copper recovery by up to 3.5%, zinc recovery by up to 12%, gold recovery by up to 8-10%, allowing to increase the recovery of valuable components by 1.5-12.0%, basically this kind of reagents nearly double the flotation rate, improve the grade of the concentrate, improve the stability of the flotation process parameters, and reduce the environmental impact of flotation plants."

Jan 1, 2018

By Willis Forsling, Prabhakar Swarna, Hanumantha Rao Kota

The solubility of wollastonite and its Hallimond flotation behavior as a function of dodecylamine concentration and pH are examined. The flotation response is characterized by adsorption and surface energy in the presence of amine. The methods of UV-Visible and FT-IR spectroscopy for adsorption and sessile-drop contact angle for surface energy estimation are employed. The results of wollastonite dissolution clearly showed its non uniform dissolution. The surfaces are depleted with calcium ions and became rich in silicon within 10 min of flotation time. Maximum flotation of wollastonite corresponds to a half monolayer coverage of amine, which is substantiated by the surface energy parameters. A good correlation between flotation, adsorption and surface energy as a function of amine concentration and pH was observed. The sudden increase in wollastonite flotation and amine adsorption at and above 5x10-5 M initial amine concentration is thought to be due to two-dimensional precipitation of amine on surface in accordance with the recent 2D-3D precipitation model of amine adsorption on silicate minerals.

Jan 1, 2003

By Yuemin Zhao

Pre-combustion cleaning of coal plays a key role in the process of efficient and clean utilization of coal resources. Recently, wet beneficiation of coal is predominant around the world. Nevertheless, wet beneficiation processes are limited by the increasingly serious problem of worldwide shortage of water, especially in China. Thus, it is imperative to develop efficient dry coal beneficiation techniques. Currently, several technologies such as air dense medium fluidized bed, compound dry cleaning and air jigging have successfully achieved high-efficiency separation of 50~6 mm coal. However, in recent years, a large amount of fine coal is generated as the mechanized mining technology has been progressively deployed in coal sector. Thus, it is necessary to develop efficient dry beneficiation techniques for fine coal. In recent years, many countries including China, India, Canada, Germen, and Australia have carried out many research works on fine coal dry beneficiation techniques. China University of Mining and Technology has carried out systematic researches on the introduction the vibrated energy to traditional air dense medium fluidized bed for fine coal beneficiation. This paper studied air dense medium vibrated fluidized beds (ADMVFB) for fine coal dry beneficiation. The experimental results show that the coal of <6 mm size can be beneficiated in an ADMVFB efficiently with the E value of 0.065~0.085, the separating density can be adjusted in the range of 1.45~2.2 g/cm3, and the lower limit of beneficiation can reach to 0.5 mm. Keywords: fine coal, air dense medium vibrated fluidized bed, coal separation, dry separation

Sep 1, 2012

By M. Brozek

The particle settling velocity is the argument of separation in such processes as classification and enrichment in jigs. It characterizes material forwarded to the separation process and belongs to the so-called complex arguments because it is the function of particle density and size. i.e. the function of two simple arguments. The affiliation to a given subset is determined by the values of two mag-nitudes and the distribution of such argument in a sample is the function of distributions of particle density and size. The paper will present a method of determining the distribution of settling velocity in the sample of spherical particles for the turbulent particle motion in which the settling velocity is expressed by the Newton formula. Because it depends on density and size of particle which are random variable of certain distributions, the settling velocity is a random variable. Applying theorems of probability, concerning distributions of function of random variables, the authors will present general formula of probability density function of settling velocity for the turbulent motion and particularly calculate probability density function for Weibull?s forms of frequency functions of particle size and density. Distribution of settling velocity will calculate numerically and perform in graphical form.

Jan 1, 2014

By Yuexin Han, Jie Liu, Shuai Yuan, Yanjun Li

"In order to improve recovery efficiency of iron minerals from iron ore tailings and to reduce its connected environmental pollution, this article investigated the reducing roasting of iron ore tailing in a laboratory fluidized magnetization roasting reactor to optimize the roasting method and conditions. The examined parameters included roasting temperature, roasting time and reducing atmosphere. The parameters evaluating magnetizing roast efficiency and theoretical value were determined. X-ray diffraction (XRD) analysis was used to investigate the conversion of iron phase after roasting. The results show that the best magnetizing roast conditions are roasting temperature of 540?, holding time of 15min, and CO concentration of 20%. The magnetization conversion ratio of roasting products is over 80%, under the best magnetic separation condition, the concentrate grade of iron is 65.61 % and the recovery of iron is 83.77 %. The XRD analysis shows that Fe exists in hematite and siderite before roasting and exists in magnetite after roasting. The technique not only recovers the iron minerals from tailings with good economic benefit, but also reduces the environmental pollution of tailings accumulation.INTRODUCTION Iron ore tailings are the solid wastes generated during the beneficiation process of iron ore concentration and are one of the main pollution concerns in the mining industry (Das et al., 1996). Continuous development of the iron and steel industry has led to the increasing amount of iron ore tailings; there are over 300 million tons of iron ore tailings discharged per year (Rao et al., 2016). The huge amount of stockpiled iron ore tailings brings a series of environmental and social problems. Comprehensive utilization of iron ore tailings can not only reduce environmental load but also conserve resources, promoting sustainable development of the society. In recent years, iron ore tailings as secondary resources have received considerable attention in many countries in the word and numbers of studies on utilization of iron ore tailings were carried out, such as recycling the valuable minerals (Datta et al., 1996; Jia et al., 2013; Panda et al., 2018), used in construction material compositions as alternative source of raw materials (Das et al., 2012; Zhou et al., 2012; Luo et al., 2016) and other utilization. The iron minerals were recovery by magnetization roasting (Rao et al., 2016; Yang et al., 2013; Yang et al., 2011) and flotation (Kumar and Mandre, 2016). By comparison the reduction roasting has more advantages, but it was found that the conventional roasting equipment was inefficient, high energy consumption and un-economically applied on an industrial-scale."

Jan 1, 2018

By Fengming Li, Baocheng Song, Yuemin Zhao, Hailin Dong, Liping Peng, Chusheng Liu, Chenlong Duan

The large-scale vibrating screens with high processing capacity and efficiency are now in great demand in the mineral processing industry of China. However, as the equipment is always suffering from the strong external harmonic exciting force, the inertial force and the impact from the minerals, the fracture of the beam and the crack of the lateral plate are easy to occur, which has a negative effect on the reliability of the equipment itself and the industrial production. Considering the essential high reliability of the equipment, a new large-scale vibrating screen with duplex statically indeterminate mesh beam structure (VSDSIMBS) was developed. The natural characteristics, namely, the natural frequency (or the modal frequencies) and the natural mode, and the dynamic characteristics of the VSDSIMBS were obtained by the modal analysis and the harmonic response analysis. In addition, the dimensions and the constructions of the statically indeterminate plate and the mesh beam were chosen as the design parameters, to which the sensitivity of the whole mass, the maximum deformation and the maximum stress of the duplex statically indeterminate mesh beam structure (DSIMBS) were summarized for the optimization of the DSIMBS. Now the large-scale VSDSIMBS is being well used in China.

Jan 1, 2014

By Ernesto de la Torre, Karla Velín, Alicia Guevara

"The following study shows the improvement and simulation of a gold recovery plant of 24 t/day of capacity by gravity concentration, flotation and leaching. The ore processed had grades of 6 g/t Au, 15 g/t Ag, and 0.69 %Cu with the mineralogy consisting of 2 %chalcopyrite, 12 %pyrrhotite, 7 %plagioclase and 50 %quartz. The recovery process starts with crushing the ore followed by grinding it further in a ball mill. The ground ore is then concentrated in a Falcon centrifugal concentrator with concentrate being processed by amalgamation process. Gravity tails are sent to a flotation circuit where the copper minerals and some gold are concentrated. Lastly, the flotation tailings undergo cyanidation for gold recovery. Currently, the overall recoveries are 82.8 %Au, 49.6 %Ag and 99.1 % Cu. The optimization was developed in the laboratory using a Wilfley table by gravity concentration. Flotation tests in the laboratory were performed using potassium amyl xanthate and pine oil. Lastly, cyanidation was then performed on the flotation tailings. The results showed the optimum concentration of sodium cyanide in cyanidation is 2 g/L, which produced an increase in gold recovery from 30% to 44%. The reduction of diameter particle from 132 to 80 µm also produces an incremental recovery of gold and silver from 11% to 21% Au and 0.4 to 3% Ag in gravity concentration. Likewise in the cyanidation the recovery of gold and silver has shown a rise from 44 to 62% and 8 to 32% for Au and Ag respectively. However, the flotation method the gold recovery is reduced from 68 to 30% Au by reducing the particle size. Computer simulations using the programs, Moly-Cop and ModSim were performed to determine optimum parameters for the recovery of precious metals at the gold recovery plant."

Jan 1, 2014

By Tatyana A. Ivanova, Tamara N. Matveyeva, Anatoliy A. Fedorov, Tatyana V. Nedosekina, Valentin A. Chanturiya

An ingenious methodology purposively developed by the authors for comprehensive assessment of flotation properties, electrophysical characteristics and. crystal chemistry features of natural gold-bearing sulfide minerals of different origin has been used in this study. Examination of the elemental composition of the minerals, ion-molecular components of the liquid phase in suspensions, surface properties of sulfides and different flotation reagents sorption forms was performed using the methods of X-ray phase and spectral analysis, potentiometry, UV and IR spectrometry, computer image analysis, and computer simulation techniques. The role of isomorphous impurities in the formation of hydrophobic sulfhydric collector layers on mineral surfaces in complex ore processing has been elucidated. The parameters characterizing the variability of the Fe:S ratio in pyrite of different origin have been determined based on non-stoichiometry characteristics of natural gold-bearing sulfide crystals. An ingenious method of formatting and linear approximation of experimental data was used to find out the quantitative relationships between the impurity content, electrophysical characteristics, non-stoichiometry and floatability of pyrite from a number of different deposits. The effect of the impurity species present in sulfides on the characteristic pH value marking the floatability peaks as such and their trend of shift towards higher alkalinity has been revealed. A theoretical substantiation has been given to prognostic assessment criteria for processing characteristics of gold-bearing sulfide minerals with varying composition. New flotation reagents and advanced reagent systems which help to increase the contrast of processing characteristics for different gold-bearing sulfides, resulting in improved selectivity, have been developed. The mechanism of selective flotation of precious metal-bearing Fe and As sulfides achieved by using short-chain dithiocarbamates and a mixture of cyclic trithiocarbonate with oxyalkylsulfides has been analyzed.

Jan 1, 2003

By Junji Shibata

In a present process to treat the tungsten carbide tool waste, the wastes are roasted in air and then an alkali leaching is carried out in an autoclave. An environmentally friendly process is required to recover rare metals (Co and W) from the wastes. The effect of mechano-chemical (MC) treatment on leaching of rare metals was investigated in this study. The solvent extraction and crystallization-stripping methods were applied to separate and recover tungsten and cobalt in the leached solutions. The MC treatment for the rare metal leaching is effective to dissolve rare metals from the wastes due to the change in crystalline structure of WC and oxidation of WC with KMnO4. Cobalt ions are extracted with D2EHPA by a cation exchange reaction. Tungsten in the leachate can be extracted by TOA (tri-octyl amine) as an extractant, because tungsten species exist as a form of anionic species in acidic solution. The rare metals in organic phase are recovered as insoluble salts such as oxalates and ammonium salts in the crystallization-stripping process. Keywords:unheated oxidation, solvent extraction, crystallization-stripping, recycling

Sep 1, 2012

By C. Han

The analytical results of Dagushan grinding workshop primary grinding operation product show that the size fraction of -0.079mm is 32.88%, the size fraction of -0.01mm is 9.97%, the rate of -0.01mm size fraction and -0.079mm size fraction is 30.32%. It means that there is too much -0.01mm size fraction in primary grinding operation product and fall out that there will not be a better result in following operations. Several tests have been carried out to control the size distributing of the primary grinding operation product according to confirm the appropriate conditions of grinding operation. Integrate with theoretic count, grinding property tests show that the appropriate rev ratio of ball mill should be between 85% and 90% so as to get better size distributing. Based on the results of grinding property tests, the shocking property tests simulated the momentum of different diameter steel balls in the ball mill have been carried out. It showed that if want to get better size distributing the appropriate diameter of steel ball should be 110mm. The tests result shows that regulate diameter of steel ball and rev ratio of ball mill could control the size distributing. Contrast to the technical parameters of ball mill in grinding operation now, there are some significant advices are given for practice and industrial tests.

Jan 1, 2014

By Güven Önal, Gülay Bulut, Mustafa Özer, Yunus Emre Benkli, Olgaç Kangal, Mustafa Tarkan

There are various types of natural zeolite deposits in Turkey. Naturally occurring zeolites are excluded from many important commercial applications where uniformity and purity are essential. In this paper, the beneficiation of natural zeolite, taken from western part of Turkey, was investigated. According to X-Ray Diffraction (XRD) and mineralogical studies carried out on the representative ore sample, the natural zeolite was found to be in the forms of clinoptilolite and heulandite. Clinoptilolite forms as a devitrification product of volcanic glass in tuffs. Quartz, clay minerals, orthoclase, plagioclase, biotite, seruzite-muskovite and epidote were observed as impurities. Several types of mineral processing methods were performed in order to remove impurities from the natural zeolite sample to produce high purity zeolite. Gravity separation methods such as shaking table and superpanner were carried out for separating heavy minerals, while high intensity dry magnetic separation was used for discarding magnetic minerals.

Jan 1, 2003