Search Documents

By Sup Hong

"Lifting riser in deep-seabed mining (DSM) is exposed to acute and chronic stresses of materials, whose yield will result in the most critical loss of total mining system. For freehanging riser (FHR), the axial vibration and local bending of riser may produce acute stresses, in the meanwhile, vortex-induced vibration (VIV) in relative current, friction and collisions of solid particles with inner-wall, and material corrosion in seawater are representative causes of chronic stresses. The chronical stresses bring about fatigue failure or abrupt failure by material loss. Hydraulic lifting is effective and promising for transportation of minerals, however, ecofriendly treatment of operating seawater is an unease hurdle to come over. Sizing of riser section confronts multi-directional problems, i.e. safety of slurry transportation (flow assurance), material safety of riser (wall thickness), seawater treatment on board, etc.A free-standing riser (FSR) might exclude a part of design problems of free-hanging riser and give a way to sustainable mining. FSR stands vertically by means of sub-buoyancy part(s). The top of FSR emerges above sea surface and is connected with mining platform through jumper line (supported by external yoke). Total amount of sub-buoyancy and location(s) have to be carefully determined in viewpoints of dynamics of FSI (fluidstructure interaction) in waves and currents. The concept of FSR gives more freedom for design of multi-functional riser system in view of sustainability of DSM. In DSM, sustainability concept may be focused on eco-friendly treatment of seawater and sediment, and safety of total mining system. For feasibility of FSR, however, installation, maintenance and repair need to be investigated thoroughly in collaboration with industry experts"

Jan 1, 2017

By Dennis Sánchez Mora, John Jamieson

INTRODUCTION Work by Humphris et al., (2002); Ondréas et al., (2009); Barreyre et al., (2012); and Escartín et al., (2015) has identified active and inactive hydrothermal sites along the Lucky Strike segment. The sites that contain the largest accumulation of known sulfides are located between the north and the southern zones (Figure 1), a vent site area that is referred to as the Main Lucky Strike hydrothermal field (Escartín et al., 2015). Hydrothermal fluid outflow has been linked to a shallow fault network (Barreyre et al., 2012). However, specific constraints on fault geometries have not been determined. Other off-axis sites at Lucky Strike, such as Capelinhos (high temperature vent), and Grunnus (inactive?), as well as a low temperature vent field (on-axis), Ewan, have been described by (Escartín et al., 2015). Given the spatial relationship between the Main Lucky Strike hydrothermal field (MLSHF), and the intersection of northern rift faults with the southern rift faults, a structural analysis of this area can provide insight into the fault controls on fluid flow that leads to hydrothermal venting and sulfide precipitation. METHODOLOGY Structural data (dip direction and dip) was determined using Leapfrog Geo 4.0 software. Bathymetric data was obtained from Escartín et al., (2015) and references therein. The bathymetry was imported into Leapfrog Geo (in UTM format) and, using the structural modelling tool, individual measurements with dip direction and dip data were collected with a focus on the northern volcanic rift and the southern central volcano (Figure 2a). All measurements were taken from what the authors consider as normal faults, and to aid the determination of individual measurements a “face dip” map was constructed, where the bathymetry is colored by slope angle (Figure 2b). All measurements are simultaneously plotted on a stereonet generated by the Leapfrog Geo Software. Data were divided into northern and southern, and western and eastern zones to determine the relationship between hydrothermal venting and the structural geometries at Lucky Strike (Figure 2c). Slip measurements for individual faults were determined along the dip of the fault with a measuring tool. Net slip, heave (horizontal displacement), and throw (vertical displacement) was calculated for each of the zones.

Jan 1, 2018

By R. K. H. Falconer, Wood R. A., C. D. Castle

"A deposit of phosphate nodules is on the Chatham Rise approximately 450 kilometres to the east of Christchurch in the South Island of New Zealand. The deposit contains sufficient rock phosphate to supply New Zealand’s phosphate fertilizer needs for at least 20 years. It was first investigated commercially 50 years ago by Global Marine, followed by JBL Minerals in the early 1970’s. NZ and German government research and industry groups then took it up again, with major field programs in 1978 and in the early 1980s.Due to difficult global and local economic conditions the project ground to a halt in 2004.The project was resurrected in 2007 when Chatham Rock Phosphate applied for a prospecting licence. This was granted in 2010 and a successful subsequent mining permit approval followed in 2013. The initial application for the separately required environmental permit was declined in February 2015.A lot has changed then and the significance of this will be the subject of the presentation. Chatham Rock Phosphate is confident that an environmental permit will be successfully granted next time."

Jan 1, 2017

By Hans Smit

The face of mining as we know is changing as mining companies all over the globe realize the reality of accessing the vast mineral wealth contained on, and under, our ocean floors. With some land based mineral deposits being fully exploited across the world, deep sea mining is set to revolutionize global approaches to the search for precious metals and other sought after minerals. Previously, the financial and technological implications of deep sea mining outweighed the benefits of access to the mineral rich deposits identified all around the world. The process of marine diamond mining off the west coast of southern Africa started in the late 1950s, and subsequently continued by De Beers to the present day, has proven to be an excellent proving ground for the development of technology and mining systems that ensure a sustainable and financially viable business.

Jan 1, 2011

By Andrea Koschinsky

Recent technological breakthroughs in the fields of ceramics, medicine, aerospace engineering and electronics (semi- and superconductors) are constantly creating new uses and an ongoing increasing demand for a variety of rare valuable trace metals. These so-called high-tech elements such as hafnium (Hf), titanium (Ti,) niobium (Nb), tantalum (Ta), zirconium (Zr), molybdenum (Mo), vanadium (V) and the rare earth elements (REE), many of them of strategic importance, occur inter alia at elevated and potentially economic concentrations in marine ferromanganese nodules and ferromanganese crusts, making those deep sea deposits potential future resources of these metals. As these metals are mostly present in the lattice of the manganese and iron phases, which are strongly intergrown, rather than in separate mineral phases within the nodules and crusts (Koschinsky and Hein, 2003), reductive dissolution of the host phases is a prerequisite to release and dissolve the valuable metals. To evaluate the association of these rare valuable metals with their mineral carrier phases, sequential leaching experiments were carried out on selected samples in a first step in our project.

Jan 1, 2011

By J. R. Woolsey

In late 1988, the Committee for Coordination of Joint Prospecting for Mineral Resources in South Pacific Offshore Areas (CCOP/SOPAC), Suva, Fiji, consulted the Continental Shelf Division of the Marine Minerals Technology Center regarding low-tech, low-cost, reconnaissance sampling systems for a variety of nearshore needs. Materials of interest to several member island nations included silica and calcareous aggregate for cement manufacture, sand for beach replenishment, heavy minerals, and precious metals. A principal criteria of the system was that it be of low-tech design, and as far as possible, suitable for construction on the islands from available materials. It should also be operable with SOPAC personnel on island vessels of opportunity. The system selected to satisfy these requirements was a convertible drill of basic airlift design, capable of operating with easy modification as either a vibralift or airlift, depending on the desired application. The basic system included a drill pipe constructed of heavy duty 76 mm (3") black iron pipe, divided into three 3 meter sections (for ease of transport), fitted with an air intake manifold and bit at the lower end. A 25 mm (1") galvanized pipe assembled in three similar sections and clamped to the drill pipe served as a water jet to assist in cutting. Air was supplied to the manifold by means of a 12 mm (1/2") pipe also clamped along the length of the drill pipe. Suitable hoses supplied water and air to the upper ends of the respective pipes by means

Jan 1, 1989

By S. Jeffress Williams

Continental shelf margins are dynamic sedimentary environments that contain important benthic habitats and support many functions such as navigation, national defense, cables, pipelines, trawling, and oil and gas and mineral extraction. Coastal margins also contain resources such as sand and gravel aggregates, which are becoming increasingly important for beach nourishment to mitigate coastal erosion and enhance recreation and to restore degraded coastal ecosystems. Existing geologic maps of the seafloor and sub-bottom sedimentary character, morphology, texture, composition, and other seafloor properties are not available for some regions, are out of date and not inclusive of the massive data collected during the past several decades, and are not in GIS-based digital formats. New geologic maps, based on unified and integrated national digital datasets, showing the sedimentary character of continental margins are critical tools for both research to better understanding the geologic history and processes of continental margins as well as the distribution of habitats and resources and for managing coastal-marine resources. The majority of existing seafloor maps are decades old and do not include recent data from mapping surveys, seabed sampling and observation carried out by federal agencies, universities and industry. Because continental margins are increasingly important, comprehensive and integrated databases are needed to produce GIS-based digital maps displaying information such as seafloor geology, sediment character, texture and distribution. To meet the need for a unified database of seafloor sedimentary character, the USGS is conducting the Marine Aggregate Resources and Processes project, a national assessment of marine sand and gravel with federal, state, and academic partners.

Jan 1, 2004

By Michael J. Cruickshank

The State of Hawaii has expressed concern over deterioration of the tourist beaches at Waikiki, which are becoming seriously depleted of sand. In this report the options for acquisition, transportation and placement .of sand on the beach are examined with respect to feasibility and cost. Ten sources of sand were compared, including commercial, from Australia, Maui, and Barbers Point (3), deposits offshore of the Reef Runway (3), offshore of Waikiki (3), and offshore of Molokai from the Penguin Bank (1).

Jan 1, 1991

By Lars-Kristian Trellevik, Jan Arvid Ingulfsen

Swire Seabed is dedicated to being at the forefront of the Autonomous Subsea Revolution. The company is currently working along and developing operational, technical and market strategies where autonomous technology is the driving force. Swire Seabed’s vessel Seabed Constructor is currently mobilized and operating eight Hugin AUVs and 6 Surface going USVs. This significant and revolutionary spread is owned by Ocean Infinity. Ocean Infinity and Swire Seabed is currently involved in the search for the missing MH370 – in about 3 months the vessel and autonomous spread have fine combed an area of deep sea floor spanning over more the 100 000 km2 . With such a considerable spread with a depth rating of 6000 meter – Swire Seabed and Ocean Infinity is challenging long held paradigms in subsea mapping and resource surveys. Highly accurate and precise data can be acquired for large areas in record time, and at a comparatively much reduced cost. As one earlier required several vessels and associated crews and logistical support – Swire Seabed and Ocean infinity are now able to operate a large number of AUVs and USVs, through technological advances in automatic data-processing and interpretation, from a single offshore vessel. This opens up vast possibilities for emerging markets such as subsea-minerals. Swire Seabed is also developing strong collaborative relationships with academic institutions. Along with UIB Swire Seabed is developing methodology for deep sea geological and geophysical resource searches applying AUVs at an industrial scale – this work is based on UIBs groundbreaking work and significant experience in the same fields. In particular Swire Seabed and K.G Jebsen Centre for Deep Sea Research (UIB) have developed methodologies for conducting detailed Seep-Searches at a large geographical scale. UIB and Swire Seabed is further pursuing a formalized long term relationship for academic and industrial cooperation and exchange in AUV operation and methodology development. Whilst K.G Jebsen Centre for deep sea research have been involved in basig deep sea research for years, Swire Seabed have specialized in cost-effective heavy duty operations in water depths greater the 3500 meters. This collaboration affords the subsea mining community a unique pool of both insight and operational capacity.

Jan 1, 2018

By Laurie Meyer

The need for improved, high confidence estimates of nodule abundance to support mine permitting, detailed mine planning and mining and processing equipment design is evident. To date, physical samples represent the ?Gold Standard? for nodule abundance measurement, and are likely to remain as such. However, there are some interesting improvements in the area of 3-D scanning which, if marinized for operations at 6000m, may prove to be reliable alternative methods for mapping abundance over large areas particularly if calibrated or benchmarked with physical sample data. . Features of a high confidence physical sampling device, such as the 0.75m2 (0.86m on a side) box corer developed and successfully used by the Kennecott Group for exploration in the CCZ, take into account not only the accuracy in nodule sample collection but a host of other operability considerations which can mean the difference between a successful exploration cruise yielding high numbers of large area samples and one in which few, inaccurate, often inconclusive samples are collected (or, even worse, the sampler fails to grab any nodules for any number of reasons). The collection of physical samples at appropriate spacing within a mine area combined with more qualitative indications of nodule density such as can be obtained using acoustic backscatter should prove adequate for the near term objectives related to overall abundance appraisal or estimates of ?indicated? resource. Looking ahead, exploration cruises will need to yield increasing amounts of data to support development of higher confidence resource abundance estimates to support issuance of mining permits and detailed design of mining plans and equipment. It is likely

Sep 14, 2011

By Randolph A. Koski

Recent investigations located at least six major massive sulfide deposits (dimensions measured in tens to hundreds of meters) within a 50-km-long segment of Escanaba Trough, the sediment-covered axial valley of southern Gorda Ridge. The sediment fill is intercalated silt and sand turbidites and hemipelagic mud with a maximum thickness of 500 m. Several volcanic edifices, spaced at approximately 15-km intervals along the ridge axis, penetrate and locally breach the sediment. The largest sulfide deposits form mounds and ridges on the steep flanks of structurally unstable sediment-capped blocks that have been uplifted above the volcanic edifices; both sediment and sulfide deposits are undergoing rapid erosion and redeposition. Although hydrothermal activity appears to be absent at most sulfide fields, 220°C fluids are discharging from the tops of sulfide mounds near 41°00'N lat, 127°31'W long. Recent pillow lavas and sheetflows erupted onto the sediment-covered sea floor less than 500 m away from the active vent field. The massive sulfide deposits have compositional characteristics that differ from deposits formed on sediment-free spreading axes. The Escanaba Trough deposits include Fe- and Cu-rich, Zn- and Pb-poor massive sulfide mounds, polymetal (Zn-Fe-Pb-Cu-As-Ag-Sb-Sn) sulfide vent structures, abundant barite-rich chimneys, crusts, and sinter cones, and thermogenic petroleum in the sulfide and sediment. Sulfate-rich crusts have high Au values ranging between 2 and 10 ppm. The unusual mineral assemblage at Escanaba Trough

Jan 1, 1989

By William D. Siapno

Mining the deep ocean by the year 2000 may seem far fetched. The year 2000 is but a decade away, a scant 10 years. Remember, the youngsters of today will grow up in a little more than a decade and rebut the wisdom of the ages, especially the traditions of their elders. Rude perhaps, but none the less a fact of life. Ocean mining exhibits many of these same traits. We should all brace ourselves for some rude shifts in our rapidly moving society. Major shifts in economics, politics, and social orders are the rule of the day. Communism is in retreat, our own economic structures chaotic. So in this moment of cataclysmic change, a shift in the international market place of mineral resources should not be a great surprise.

Jan 1, 2011

By Pedro Madureira, Georgy Cherkashov, Harald Brekke, Marzia Rovere

"The most promising deep-sea mineral resources for exploration in the Area (beyond the limits of national jurisdiction) are polymetallic nodules, cobalt-rich ferromanganese crusts and polymetallic sulphides. These marine minerals have different characteristics in their distribution, geological setting, grades of metals and genesis. Considering future exploitation of nodules, crusts and sulphides such parameters as estimated resources, specific mining operations and ore processing are different as well.Comparative analyses of deep-sea mineral minerals as well as onshore and offshore resources will be discussed in the paper."

Jan 1, 2017

By Robert Heydon

With the United Nations Conference on Sustainable Development fast approaching it is timely to reflect on the integral role seafloor polymetallic nodule mining will play in facilitating sustainable development and alleviating global poverty. Polymetallic nodule mining presents mankind with a unique opportunity to advance the world?s sustainable development aspirations, particularly given the ultimate beneficiaries from polymetallic nodule mining will be the billions of people around the world that require greater access to more affordable minerals for their social and economic development. This paper discusses the importance of polymetallic nodule mining in the context of sustainable development and forecasted growth trends, supply and demand dynamics, the decreasing grade and quality of terrestrial mineral resources, and the Green Economy, as well as in light of a comparative analysis that demonstrates polymetallic nodule mining offers a socially and environmentally advantageous alternative to terrestrial mining.

Jan 1, 2011

By Ian B. Corbett

De Beers Marine Pty Ltd. (South Africa) (DEBMARINE), a wholly owned subsidiary of De Beers Consolidated Mines Ltd. specializes in the provision of contracting and consulting services for offshore diamond exploration, Mineral Resource Management and mining. Established in 1983, the company is strongly focused on driving and sustaining growth of the offshore diamond mining industry into the 21st century. DEBMARINE provides full Mineral Resource Management and produce almost half a million carats annually for the Namibian Diamond Corporation (Pty) Ltd. from their offshore mining licence. The company is also extensively involved in feasibility studies to establish new mining ventures and in the exploration of several offshore Prospecting Licence Areas for other clients. As a pioneer in this field, DEBMARINE remains highly focused on technological development. A specialized section, the Technical Development Business Unit, has been established. Through relationships with various technology leaders, this unit develops new sub-sea mining technology and delivers productivity innovations aimed at realizing maximized carat extraction. This talk provides a broad perspective on the development of the Namibian offshore deposits and examines the critical role played by high-resolution orebody characterization and high-confidence Mineral Resource development at De Beers Marine.

Jan 1, 1998

By Francois P. Leroy

In the quest of studying the assigned blocks of seafloor for deep water mining, each member country of the ISA is thirsty for accurate information as to the level of resources available. Manganese nodules represent a large portion of the resources and are as precious as they are hard to locate and harvest. Resolving such challenges is what drives the technology development and yields instruments and products capable of serving this field of research. This presentation will study how manufactures of oceanographic instruments have pushed the technology envelop to in order to transform a collection of sensors and instruments into a seamless and adapted assembly working to serve the researcher and prospector in the challenging field they operate. Deep water data collection is characterized by the following challenges: ? Deployment, recovery and handling of the vehicle ? Producing high resolution at great distances ? Positioning that data with accuracy to relocate Teledyne Marine will present the work performed in its engineering laboratories to produce sub systems and systems now capable of delivering key information necessary to the proper cataloguing and exploitation of deep water mineral mining. Understanding and controlling the alternative resources available to each country will allow better management of current traditional land based minerals.

Jan 1, 2010

By Elisabetta Tedeschi, Razieh Nejati Fard

Deep-sea mining is in the future perspective of mining industry and it is currently in the technological development phase. The focus of this study is on the electrical power system that provides sufficient energy for the mining equipment at the seafloor, excavating Seafloor Massive Sulfide (SMS) deposits. SMS deposits usually exist at water depths between 1500 m and 4000 m. Despite the similarities of SMS deposits excavation to the open-pit terrestrial mines, more energy is required to drill and crush the ores in the hyperbaric conditions [1], which can be done whether by static trench cutters [1] or by mobile mining crawlers [2]. In addition, the ores vertical transportation by subsea pumps requires several MW electrical power that can be supplied by all-electric subsea motors or hydraulically from water injection motors located on the surface. The power requirements can be fulfilled by an offshore or subsea power network. As the SMS mines are usually in remote locations, the straightforward solution will be an isolated offshore grid mounted on a vessel or platform similar to the most of offshore Oil & Gas projects. These power systems resemble the onshore microgrids for industrial purposes operating in island mode. However, in contrast with the onshore power networks, there are space and weight limitations in offshore infrastructures, which impose the design compactness to be a priority. In addition, having a very high reliability is necessary in the design approach of the offshore projects due to the extraordinary high expenses corresponding to repair and maintenance. The other design criterion is to improve the power system efficiency in order to reduce the size of the power equipment cooling apparatus, operational costs and CO2 emissions produced by diesel/LNG onboard generators. There are a few studies considering power system distribution for seafloor mining industry. Among them, [3] has investigated the AC and DC alternatives for SMS mining in 2400 m water depth by considering Solwara 1 project scenario introduced by Nautilus Minerals Inc. [2]. In this study, a power system design tool will be presented taking into account various water depth, power consumption levels, different distribution configurations (AC and DC) and the aforementioned design criteria.

Jan 1, 2018

By C. L. Mardock

The U. S. Bureau of Mines participated in a two-year joint State of Oregon/Department of Interior Placer Task Force study on the economic and environmental aspects of Oregon's marine placer deposits. The effort culminated in a research cruise off the southwest coast of Oregon to investigate the geological and biological characteristics of the continental shelf deposits. The Bureau's role was to collect and study the placer material off the continental shelf and to determine its strategic potential and significance. In-depth characterization of the sediments by optical and electron microscopy verify that the placer material from Cape Blanco contains up to 3 pct ilmenite, 0.5 pct chromite, and small amounts of zircon and gold. However, harsh sea conditions and equipment failures prevented sampling below a four-foot depth at the Cape Blanco site. Results to date indicate that the deposits sampled off the southwest coast of Oregon do not represent a significant source of strategic minerals. However, further study of the deeper sediments off Cape Blanco may uncover significant concentrations of chromite. This presentation encompasses the site geology, the geophysical and biological activities of the expedition, and the results of the Bureau's mineralogical and chemical investigation. The combined findings of the Bureau and other Task Force agencies have provided information needed to expand the country's limited knowledge of marine mineral resources and has assisted state and federal agencies in the formulation of offshore mineral policies.

Jan 1, 1991

By LeRon E. Bielak

The marine minerals program of the Minerals Management Service (MMSI has undergone significant changes during 1991. Formerly the Office of Strategic and International Minerals, the program has been renamed and invested with additional responsibilities. The new name, Office of International Activities and Marine Minerals, (INTERMAR) reflects its dual mission. INTERMAR'S role in the international area was broadened in January 1991 to provide the MMS with a focal point for identifying and coordinating international opportunities of mutual interest and benefit. Opportunities include energy and nonenergy minerals and a broad range of areas such as resource and environmental assessment and management, structural and operational safety, royalty management, regulatory matters and public affairs. Cooperative efforts involving information exchanges, training programs, research, and similar arrangements are receiving particular emphasis. Australia, Canada, France, Japan, Sweden, the United Kingdom and the USSR represent a growing list of countries with whom arrangements have been established. Support has also been lent to other Federal Agencies and the United Nations in areas where MMS expertise and resources can impart a significant contribution. Opportunities will also be explored which involve Pacific insular areas.

Jan 1, 1991

By J. M. (Mac) Beggs

With New Zealand?s ratification of the United Nations Convention on the Law of the Sea in 1996, the government of the day increased work on developing an oceans strategy to help create a governance framework for the country?s extensive existing and potential maritime territories. This project took a new direction in 2001 with the establishment of an ad hoc committee of 6 Ministers, and their appointment of a Ministerial Advisory Committee (on which the senior author served) to consult with the public, identify widely held values and inform the development of a Vision for subsequent policy development. The current second stage of the policy development process involves a working group of officials from the relevant agencies completing a stock-take of existing laws and regulations to identify overlaps and gaps that should be addressed in the third and final stage. The public consultation process revealed, as might be expected, a wide range of perspectives but a solid consensus in favour of a coherent, and balanced, framework to enable the realization of economic benefits of ocean development so long as appropriate environmental standards (broadly expressed in terms of sustainability) are not compromised.

Jan 1, 2002