Search Documents

By Mahdi Soudkhah, Akhter Hossain

Vertical micropiles are generally considered to be low in lateral resistance. Therefore, battered micropiles are often used when additional lateral load carrying capacity is required. However, battering of micropiles can sometimes be restricted due to existing adjacent structures or utilities, especially in highly urbanized areas. For example, presented in this paper are lateral load test data from a 43-story building project in New York City where vertical micropiles were used due to proximity to adjacent structures. Three static lateral load tests were conducted on micropiles consisting of 13.375-in-outside diameter and 25- to 51-ft-long casings, and socketed 10 to 12.6 ft into the bedrock (gneissic schist). The subsurface profile above the bedrock consists of loose to very dense, mostly sandy and silty soils. The design load for the three test piles was 14,000 lb and the maximum load applied during the tests was 200% of the design load. Lateral load- displacement behavior of the free pile heads from the load tests are compared with the results of p-y analyses based on a widely used p-y method for sandy soils and using a lower and an upper bound estimates of soil index properties and strength parameters. Since the existing p-y curves were formulated for larger diameter driven piles at a specific geographic location, major differences are observed between the results of the load tests and the p-y analyses. In general, the lateral displacements estimated based on the p-y analyses using upper bound soil parameters are relatively closer to the results of the field load testing. Modified p-y curves specific to the sandy and silty soils representative of the general subsurface conditions of New York City matched with the lateral load tests are presented in this paper. INTRODUCTION Micropiles generally are limited in lateral load carrying capacities due to their relatively higher slenderness ratios (ratio of depth to diameter) compared to more conventional deep foundation alternatives, such as driven piles and drilled shafts. So, micropiles are not typically considered as deep foundation solutions when significantly high lateral loads are expected on the substructures. Various means to increase the lateral resistance of micropiles include battering and installing an oversized casing in the top portion of the piles (FHWA 2005; and Richard and Rothbauer 2004). However, it is often not possible to install micropiles in a battered position in highly urbanized areas due to existing adjacent structures or utilities. Installation of oversized casing is often restricted by limited space availability and concerns of losing lateral capacities due to closely spaced group of piles. Thus, estimation of lateral resistance of vertical micropiles can become highly important for geotechnical engineering projects in urban areas when a small to moderate amount of lateral resistances are expected from the substructures, often to withstand seismic and wind loads.

Jan 1, 2019

By Goudschaal Mark R.

"The Museum of Science and Industry U-505 Submarine Relocation project in Chicago, IL consisted of building an underground reinforced concrete vault (37' deep) for the Museum's new U-505 exhibit. This WWII submarine was captured in 1944, had been located outdoors at the Museum since 1954 and was lowered into its new exhibit area in 2004. A unique combination of earth retention, water cut-off and underpinning systems allowed a forty-two foot (42') deep excavation underneath th is historic museum. The museum - originally built in 1893 for the Chicago World's Fair - was closely monitored for building movements throughout construction. The underpinning systems, construction activities and monitoring results are presented herein. IntroductionThe historic U-505 German submarine at the Museum of Science & Industry was restored, moved approximately 1,000' and then lowered into its new indoor home (Figures 1, 2 and 3). The new underground exhibit opened this year celebrating the 61st anniversary of the German submarine's capture on June 4, 1944. On this historic day, Captain Daniel V. Gallery, a Chicago native, led the Navy in the siege of this submarine near the coast of Africa. This U-boat was the only German sub captured by the United States Navy in WWII and the Enigma machines, codebooks and publications recovered from the sub helped the war effort."

Jan 1, 2005

By Shoji Higashi, Nobuhiro Honda, Takeo Asanuma, Tatsuo Nagatsu, Masaki Kitazume, Sachihiko Tokunaga, Shigeru Kubo, Hidenori Takahashi, Tsuneyasu Onishi, Yoshiyuki Morikawa

"Various kinds of civil engineering structures and facilities were seriously damaged in the earthquake in Tohoku and Kanto regions of Japan on 11 March 2011 due to the greatness of its magnitude. In contrast, many structures resisted the large seismic force having been reinforced by the CDM (Cement Deep Mixing) method, which is often used for increasing the bearing capacity of ground and improving seismic performance. This paper summarizes the field survey undertaken to investigate damage to structures and facilities reinforced by the CDM method. Several prefectures and metropolitan areas were selected for the survey, based on the occurrence of strong seismic motions. A total of 847 structures and facilities were studied, in the survey using a questionnaire, which mainly inquired about the appearance of structures and facilities. Of the respondents to the questionnaire, 789 replied that there were no seriously damaged structures. The paper presents the damaged and non-damaged sites of CDM-technique sites and non-CDM-techniques sites. It can be concluded from the field survey that the CDM Method demonstrates high efficacy and durability against a strong seismic motions.INTRODUCTIONDuring the afternoon of 11 March, 2011, a huge magnitude-9.0 Mw (Category 9.0 on the Richter scale) earthquake occurred about 25 kilometers below the Pacific Ocean’s surface off the coast of Tohoku. This massive earthquake, now called the 2011 Off the Pacific Coast of Tohoku Earthquake was the largest earthquake ever observed in Japan. The seismic intensity of this earthquake was measured 7, the maximum on the Japanese intensity scale, as observed 7 in northern Miyagi Prefecture. The earthquake caused severe damage over a wide area from Tohoku to Kanto, and triggered large tsunamis that struck the Pacific coast of Hokkaido, Tohoku, and Kanto. The number of missing and fatalities caused by this earthquake exceeded 18,000 persons, making this an unparalleled earthquake disaster with a cost-in-life toll not experienced by Japan in recent years. Because of the scale of its seismic motions, the earthquake damaged facilities and structures of many kinds. In the years prior to this earthquake, the CDM method was used extensively to increase the bearing capacity of the ground as an anti-seismic countermeasure and to prevent liquefaction. Immediately after the earthquake, the CDM Association visually surveyed the state of damage to about 800 facilities in the Tohoku and Kanto regions where a seismic intensity of 5 or higher was observed. This report summarizes the survey of damage to facilities and structures constructed applying the CDM method in order to confirm the durability and performance of the method against seismic motions."

Jan 1, 2015

By Marco D. Boscardin, Kenneth A. Pidgeon, Adriane G. Boscardin

"Hollow bar tiebacks can offer an economical alternative to conventional solid bar and strand tieback systems for use in temporary excavation support construction. However, the limitations associated with the installation of hollow bar tiebacks require special attention during design, construction and load testing to verify conformance with conventional performance and proof testing criteria (PTI, 2014). In particular, providing a reliable free length is complicated by the 10-foot (3-m) -long, segmental, couplingto- coupling nature of the free length sheath in the hollow bar system, and addressing the fully grouted annulus of the bond zone and the free length zone at the end of installation are key concerns. In addition, it is often more convenient to install a greater number of more closely spaced, lower capacity tiebacks with the hollow bar system, compared to conventional tiebacks. This paper examines how these issues were addressed for a project involving a 60-foot (18-m) -deep sheet pile excavation through a highway embankment and a 70-foot-deep sheet pile and soldier pile and lagging excavation through a railroad embankment, both supported by a hybrid system of hollow bar tiebacks and hollow bar soil nails. The project involved approximately 300 tiebacks and 400 soil nails.INTRODUCTIONEngineers Construction, Inc. (ECI), constructed a pair of 32-foot (9.8-m) -wide (clear span), 30-foot (9- m) -high (21 feet (6.4 m) above the stream bed), cast-in-place concrete arch culverts as a design-build project for the Vermont Agency of Transportation (VTrans) in East Ryegate, Vermont. The new culverts replaced an existing 8-foot (2.4-m) -wide by 6-foot (1.8-m) -high cast-in-place concrete culvert under US Route 5 (RTE5), and twin, 2-foot (0.6-m) -wide by 5-foot (1.5-m) -high granite block culverts under the Washington County Railroad (WACR) alignment. The culverts convey Manchester Brook eastward, through the embankments for RTE5 and the WACR, on its way to the Connecticut River. The Connecticut River is located approximately 100 feet (30 m) east of the WACR embankment. The existing structures were undersized and backed up water behind the embankments during high flow events; and often trapped debris that flowed down the brook and became clogged. The existing culverts also had cracks and openings that have resulted in the loss of ground into the culverts and the formation of sinkholes in the sides of the embankments. Moreover, the reason for the large cross-sectional dimensions of the culverts was to make them of sufficient size and openness to encourage the migration of fish up the stream to spawn. The culvert through the RTE5 embankment is 144 feet (44 m) long, and the culvert through the WACR embankment is 128 feet (39 m) long, with a 57-foot (17.4-m) -long by 32–foot (9.8- m) -wide by 17-foot (5.2-m) -deep 10 feet (3 m) deep above the stream bed) open channel section between the two culverts. A plan view of the culvert alignment is presented in Figure 1."

Jan 1, 2016

By Ramin Motamed, Farshid Ghazavi, Joseph A. W. Toth

"Post-disaster reconnaissance of areas affected by earthquakes has documented extensive damage to buildings with shallow foundations located in liquefaction-prone areas. Currently, estimation of liquefaction settlement is based on empirical correlations that evaluate settlement in the free-field environment and are based on one-dimensional consolidation. However, observations have shown that liquefaction settlement under buildings can be considerably greater. This research is based on a series of 1- g shake table experiments using a transparent soil box to reproduce liquefaction-induced building settlement. Building settlements were evaluated using a scaled model of a building foundation representing a 1-2 story building. Comprehensive parametric study was carried out to establish the effects of several parameters on free-field and building settlements such as building width and thickness of liquefiable soil layer. The experiments utilized accelerometers and pore-water pressure sensors to monitor ground accelerations and buildup of pore-water pressures in both the free-field and model building footprint. Results of these experiments are compared to available centrifuge tests and field observations and conclusions are drawn with respect to the potential scaling effects. Lastly, this paper discusses the feasibility of installing helical piles as a mitigation strategy to reduce the building settlements by presenting some of the exploratory experimental data obtained from this series of 1-g shake table tests.INTRODUCTIONThe 2010-2011 Canterbury earthquake sequence and the 2011 Great Tohoku earthquake are some of the most recent examples where large numbers of low-story structures sustained damage resulting from liquefaction-induced settlements. This damage has commonly been observed in residential and commercial areas developed over loose, unconsolidated and saturated coarse grained soils resulting from both natural and man-made deposits. Damages incurred from the 2010-2011 Canterbury earthquake sequence occurred in the largely unconsolidated fluvial environment bordering the Avon River in Christchurch (Henderson 2013). Similar damage was also incurred during the 2011 Great Tohoku earthquake where liquefaction of soils occurred in both young alluvial deposits and fill materials (Ashford et al. 2011). Figure 1 presents typical modes of failure to structures resulting from the effects of liquefaction. Current practices in evaluation of liquefaction settlement rely on empirical correlations (Tokimatsu et al. 1987; Ishihara et al. 1992) developed for liquefiable soils in the freefield environment (Dashti et al. 2010a). However, recent observations of the performance of foundations suggest that settlement of rigid shallow foundations in liquefiable soils are commonly greater than those predicted in the free-field. Therefore, new correlations should be developed to better predict the degree of settlement of shallow foundations in liquefiable soils. Current research is beginning to focus on the mechanisms of settlement during liquefaction in regards to confining stress, pore-water pressure and shear stress induced from foundations (Dashti et al. 2010b)."

Jan 1, 2016

By Joel Moskowitz, George J. Tamaro

"A new office complex is being constructed within 25m of the Hudson River in New Jersey. The project, about 140m by 100m, will include 4 basements under the entire footprint. The perimeter was to be secured by a 0.8m thick diaphragm wall, laterally supported by high capacity tieback anchors to rock. Columns were to be supported on footings or piers to rock at a nominal bearing pressure of 3.8MPa at depths up to 17m. Although some variation in rock quality was observed in borings, a substantial vertical seam of weathered and/or decomposed rock, 1 to 2 meters wide by as much as 8 meters deep, was encountered during construction necessitating field redesign. In some locations, the seam dipped below rock that is more competent. Footings were redesigned for support on drilled caissons, or soft rock was excavated and replaced with concrete necessitating a reduction in bearing pressure of the footings by one half. The tower covering the south half of the site was topped out in 2002 and the garage levels in the north half of the site were completed in 2003.PROJECT DESCRIPTIONIn September 1999, a major investment company began the due diligence process to evaluate a property on the shore of the Hudson River in Jersey City, New Jersey for a new multi-use complex. The site offers a spectacular view of lower Manhattan directly across the river from the site of the former World Trade Center. The site, covering two city blocks, was previously occupied by manufacturing and office facilities of Colgate-Palmolive.The building footprint is approximately 140m by 100m, the southern half of which is occupied by a 260m tall office tower, shown in Fig. 1. As of this writing, design of the structure for the northern half of the site has not been finalized, but it is expected to comprise an 11-story office building. A glass-covered atrium will occupy the street that formerly separated the two blocks. As part of the due diligence process and preliminary design evaluation, alternatives were considered to accommodate various numbers of parking places, both above and below existing grade. A major consideration for below grade parking is the proximity of the Hudson River some 25m east of the east building line."

Jan 1, 2004

By Jim Bruce, Peggy Hagerty Duffy, Mary Ellen Large, Allen Cadden

"Over the past 40 years, Deep Foundations Institute (DFI) has executed its mission “to bring together multi-disciplined individuals and organizations to find common ground and create a shared vision and consensus voice for continual advancement in the deep foundations industry”. Like DFI, micropile technology began a significant growth path in the mid-1980s. This paper highlights how DFI’s mission was executed in the deployment and expansion of micropile technology.INTRODUCTIONMicropiles are small diameter foundation elements constructed using specialty drilling and grouting methods. Micropiles have evolved since their introduction into the North American market in the 1970s from being lightly loaded (less than 30 kips) elements used primarily for remedial applications, to today’s high-capacity, often hybridized foundation systems, for both remedial and new-build projects. Micropiles now occupy a substantial market segment in North America.For 40 years, DFI has aimed to be the forum for discussion of all issues related to deep foundations design and construction. DFI now supports 21 technical committees and working groups on all deep foundations technologies and has expanded to include regional chapters in Europe, India and the Middle East.Several key steps are required for the successful execution of DFI’s mission, including identifying a need, engaging dedicated and knowledgeable people, developing effective vehicles and resources for information sharing, cultivating stakeholder contributions and advancements, stimulating influence/impact on deep foundations market, and expanding approaches to continue progress. Pile drivers in New York City (the original organizers of DFI) positively affected their market using these same steps: they recognized a specific need, gathered the people who could affect change, convened a discussion forum (which is common today, but was innovative at the time), defined tasks to address the issues, and influenced their market by improving means, methods and owner perception of their services. These forward thinking, proactive members created a mechanism for communication among all related parties that would advance the profession by improving safety, quality and value of pile driving construction.Micropile technology has evolved in the United States and around the world for the past four decades. The accumulated efforts of DFI and other, similar organizations such as The International Association of Foundation Drilling (ADSC) have contributed to this evolution. The advancement of the micropile industry – and consequently the micropile market – has been intimately tied to the execution of the mission of DFI."

Jan 1, 2017

By Bernardo J. Jiménez Vega, Edy L. T. Montalvan

During the last phase of the Circunvalacion Norte project in San Jose, Costa Rica, preliminary designs for an underpass structure of over 16 km (10 miles) considered drilled shafts as an earth retaining system. Since the project’s execution was delayed and close to the deadline, it was necessary to optimize this structure, with the drilled shafts being the most critical aspect. The key element in order to obtain an improved design was characterizing the job site with a specific site study for seismic demand, and the use of advanced numerical modelling, considering soil-structure interaction. The site investigation comprised the CPT, PMT, MASW geophysical tests, deep exploration drilling, and triaxial compression tests. The terrain was modeled using an advanced constitutive model with hardening plasticity calibrated from the triaxial tests. Plaxis software was used to calibrate the seismic model for the terrain and for the dynamic analysis. Two conditions were considered for the retaining structure: free-head and fixed head. A parametric study with drilled shafts of 1.0 m (3.3 ft) and 1.2 m (3.9 ft) in diameter, and center-to-center spacing of 1.3 m (4.3 ft) and 3.0 m (9.8 ft) was conducted in order to obtain an optimized structure. For each condition of the drilled shaft wall, the computed deformations were compared for two spectrum designs: site-specific spectrum and seismic code generic spectrum. Finally, a dynamic analysis was performed to check the performance of the drilled shafts with optimized spacing using a control earthquake. Based upon seismic performance curves, the analysis showed the possibility of greater spacing for the drilled shafts compared to the original design, obtaining a 32% reduction in the total length of the drilled shafts in the project.

Oct 1, 2022

By James F. Davis, Matthew A. Conte, Robert F. Tonning

This is a paper demonstrating the steps taken to combine multiple types of piles for a single site to maximize the benefits and characteristics of each method. We intend to discuss the use of grouted displacement piles in lieu of traditional pile types that were specified on an individual project. We will show how implementing this alternate pile type can both supplement and replace the originally specified pile to increase efficiency and lower costs. We will demonstrate a reduction in spoils, vibration, crew hours, and equipment size while employing methods to overcome unforeseen ground conditions.

By Sarah Ramp, Daniel V. Cacciola, Justin Labrozzi, Shafiq I. Siddiqui, Faisal Ahmed

"Construction of embankments up to 34 ft in height for twelve ramps and roadways needed for the New Jersey Turnpike Interchange 14A project required ground improvement. The subsurface conditions, consisting of up to 30-ft thick layer of highly-compressible peat and organic soils, would induce up to 8 ft of primary and 4 in. of secondary consolidation settlements to the embankments over a long period of time. Innovative ground improvement solutions were needed to meet unique challenges posed by the poor subsurface conditions, space and existing utility constraints, aggressive construction schedule, and massive size of the project. A variety of ground improvement techniques were utilized in six different zones of the embankments to limit settlements and ensure stability of the embankments. These techniques included preloading with surcharge and prefabricated vertical drains (PVD), load balancing using light weight fill, and concrete column rigid inclusions (RI). Additionally, augercast piles with load transfer platform were used under an existing bridge with low vertical clearance. An innovative approach consisting of preloading with surcharge and PVDs followed by installation of RI was needed in one of the six embankment zones with the worst, i.e., very soft, soil conditions. The design of the RI was performed by a specialty ground improvement contractor (SGIC) using Plaxis 2D and 3D softwares. The performance of the ground improvement systems was verified and monitored by load tests and instrumentations. This paper presents details of the ground improvement design, construction, monitoring results, and lessons learned, with a focus on the RI.INTRODUCTIONNew Jersey Turnpike Interchange 14A is located within the cities of Bayonne and Jersey City, in Hudson County, New Jersey. The New Jersey Turnpike Authority (NJTA) identified Interchange 14A as an area of mass congestion in need of redevelopment to improve the increasing demand of traffic and roadway safety. The New Jersey Turnpike Interchange 14A project included the construction of twelve (12) new roadways, in addition to the construction of four new bridges. The limits of construction are shown in Fig. 1.The fill height required to construct the roadway embankments varied from 2 to 34 ft. The proposed embankment side slopes varied from 6H: 1V to 2H: 1V. Additionally, mechanically-stabilized-earth (MSE) walls were utilized to retain the embankment fill along some segments of the roadways. As shown in Table 1, the proposed roadways were divided into six zones, based on location, subsurface condition, and embankment height."

Jan 1, 2017

By Frederic A. Verheyde

The CPT pile design method of the ‘Laboratoire des Ponts et Chaussées’ (LPC) uses the cone resistance (qc) for the design of axially loaded piles. It was originally proposed in 1982 and was revised in 1993 and 2012. It has been widely used in France for several decades and is included in the current French pile design code. The objective of this paper is to summarise the two first versions (1982 and 1993) of the method and to detail the most recent one as described in the current French pile design code (AFNOR 2012).

Nov 1, 2022

By Amanda R. Parry, Chris R. Pray

Predicting and modeling the soil structure interaction of laterally loaded piles with significant unbraced lengths is one of the challenges faced in designing many waterfront structures. Designers often rely on pile specific design software to calculate forces in an embedded pile and then couple that with either a structural design software to capture the behavior of the rest of the structure or use potentially overly conservative assumptions to omit modelling the piles entirely. Given that some projects have hundreds of piles coupled with hundreds of loading conditions, the shuttling of results from the structural analysis software into the pile analysis software can become cumbersome, difficult to track and manage, and prone to user input errors. An alternative approach recently used on two large marine infrastructure projects consisted of calibrating a structural analysis software to replicate the resultant outputs from a software developed specifically for pile analysis. This calibration was done using thoughtfully placed springs along a pile modeled in the structural analysis software to replicate the soil-structure interaction of the piles. The focus of this paper will be on the methodology used to calibrate the two software programs and an evaluation of the results which showed close agreement. Based on the two case studies, calibrating a generic finite element analysis software via this method should be considered as a reasonable and time saving design approach for pile-supported structures.

Sep 8, 2021

By Nadir Ansari, Brian W. Wilson, Marina S. W. Li

"A hybrid Deep Mixing (DM) shoring system was recently constructed for a high-rise development in downtown Vancouver, British Columbia, Canada for the temporary support of a five-level basement excavation. The site is bounded by an existing bridge off-ramp structure along its longest side and by city streets on the other two sides, which formed a truncated triangle in plan. A conventional secant pile wall was installed along the longest side, about 380 ft (116 m) in length, of the site. Hybrid shoring walls (HSW) 1 and 2 were installed along two shorter sides with each being 235 to 246 ft (72 to 75 m) long. HSW 3 completed the excavation support system along the shortest side with a length of about 55 ft (17 m). Cutter soil mixing (CSM) was proposed by the excavation and shoring design-build team in lieu of conventional secant piling. CSM was the preferred method to construct the infill panels between soldier piles because of the speed at which the shoring system could be constructed in the variable fill, peat, wood waste and overburden. Design ConsiderationsTo minimize the impact on buried utilities along the outside perimeter of the excavation, the temporary shoring was designed to limit the lateral displacements to less than 0.8 in (20 mm). Factors taken into consideration for shoring design included the lateral earth pressures from the fill and native soils, groundwater pressures, temporary construction loads (e.g., crane or heavy plant/equipment), and permanent structural requirements. The subsurface conditions at this site typically consisted of fill (cohesive and granular), overlying peat and/or wood waste, overlying clayey silt to sandy silt, overlying weathered to dense to very dense clayey silt till to sandy silt till with silt layers. Localized, perched groundwater was observed within the fill, peat, wood waste and sandy silt layers above the dense till."

Jan 1, 2017

By Bernardo J. Jiménez Vega, Edy L. T. Montalvan PhD

The experience gained during more than 900 Crosshole Sonic Logging (CSL) tests on drilled shafts shows the importance of establishing proper project acceptance and repair protocols. Drilled shaft evaluation is a multidisciplinary task that should not be left solely to the outcome of the CSL test. This test allows to characterize and delimit areas of different qualities of concrete, and it is important that all the interested parties understand the difference between flaws and defects. The information presented here is intended to give a guideline to contractors, inspectors, engineers, owners and clients on how to deal with acceptance and remediation of defective drilled shafts, detected using CSL tests. A database of flaws is presented depending on their location, intensity and remediation method. Procedures that allow the flaws to be analyzed are presented in order to dismiss or classify them as defects. In many cases, the CSL test may indicate an anomaly, but by coring the concrete and analyzing the structural demands and conditions, the flaw can be classified as non-severe. When flaws are classified as defects, their repair will depend on the area where they are located in the drilled shaft pile. In this document two procedures are described for repairing defects depending on their location. For defects in the drilled shaft head area, the procedure takes into account the interaction between the new and old concrete. For repairing the middle zone of the drilled shaft by grouting, the major concerns are the difficulty of accessing through the drilled shaft at deep depths and the communication between boreholes. For defects at the drilled shaft tip, two proposed remediation methods are presented. Finally, tomography tests are presented to compare the effectiveness of remediation by grouting.

Oct 1, 2022

By Paul Hewitt, Aaron Rastall

The New South Wales South Coast rail corridor is key infrastructure for both freight and passenger transport. Geomorphological and geological evidence suggests that land instability has been widespread throughout sections of the rail corridor, long before the first documented record of landslide activity in 1879. Major landslides occurred along a 25-km length of the South Coast Railway connecting Sydney and Wollongong because of significant rainfall events of the late 1980s. Since this time, several sites have been identified as subject to instability and treated progressively under a risk priority and safety management system. Two such sites comprise a station footbridge and overhead wiring structure (OHWS), both founded on high embankments overlying colluvial materials resulting in the structures’ potential movement and associated stability concerns. This paper presents these two sites as case studies, and discusses the project geology, geotechnical models developed, interpretation of monitoring data, and successful remediation of the rail structures using sleeved bored piles. The sleeved pile system was used to isolate bored piles, which separated the bridge foundations and OHWS from the moving soil mass to ensure the piles can carry the rail structure loads, unaffected by downslope soil movements.

Nov 1, 2022

By Heman Manchanda, Sandeep Sharma

Several infrastructure projects are in various stages of construction and planning in India and almost all of them involves open ground excavation extending to varying depths. These structures are generally multipurpose and fulfil several needs of the society, their failure can be catastrophic. The design and construction of deep open excavations is generally associated with a high level of risks due to a whole series of uncertainties involved, and the success of such projects depends on various factors including appropriate evaluation of ground behavior and response to excavation stages, correct choice and analysis of construction supports, control of ground water flow during excavation, etc. One of the most critical amongst all these is ground water flow during construction and stability of underground excavation depends to a large extent on ground water control. This paper uses numerical studies for the assessment of the potential impact of ground water and ground water movement for the design of underground deep structures. The studies are being conducted using PLAXIS 2D finite element software and analysis all construction stages to which an open underground excavation shall be subjected. The paper discussed in detail the impact of water table fluctuations and comparative evaluation of different water flow conditions – a) Different Stages of excavation in line with the construction sequence (Phreatic), b) Coupled flow analysis (Transient- 1 year and 2-year duration) and c) Steady state flow conditions. The paper also covers seepage calculation and design of dewatering system.

Sep 1, 2022

By Venkata Krishnaiah Yeddala, Sai Vivek Adari, Suresh Kumar Velugu

Assam cancer care foundation (ACCF) proposed the construction of hospitals and related facilities across 18 locations in the state of Assam-India. Tezpur is one among the 18 locations of Assam with high seismic risk. The strata at the site are comprised of mostly fine silty sands of lower SPT- N values. The water table is also encountered and ranging from 1 m to 2 m below EGL. Since the site lies in seismic zone V as per IS 1893, detailed liquefaction analysis is carried out for all five boreholes and indicates that soil is liquefiable and ground improvement is inevitable up to a depth of 15 m below existing ground level. To mitigate the liquefaction potential and enhance the seismic performance of the soil, ground improvement using stone columns by Wet top feed Vibro-replacement method is proposed. Also, the differential settlements can be avoided effectively under the raft foundation with Vibro Stone Columns. In this paper, field test validation results such as Pre and post-SPTs and ECPTs to access the extent of ground improvement, along with other information adopted in this project presented.

Nov 1, 2022

By Lorie M. Dilley

Alaska Village Electric Cooperative (AVEC), an electric utility cooperative providing power to 51 Alaska villages, has made a concerted effort to install wind turbines in the villages they serve in an effort to mitigate the growing costs of electrical power generation. The subsurface soils in several of these villages consist of sands and silts with ground temperatures of between 30°F and 32°F. The presence of warm, degrading permafrost in three of the villages has required innovative foundation designs, including the use of helical piers and piles to support steel and concrete wind turbine foundations. The design of the deep foundations had to account for the effects of degrading permafrost likely resulting from observed climate change patterns. Uplift forces imposed on the foundations were approximately 100 kips per pile. Uplift pile load testing was conducted on the installed piers and piles in order to determine the actual working load that each pier or pile could sustain. In addition, pile driving analyzer testing was conducted on several piles installed in the permafrost and compared to pile load tests. Results indicated that the installed piers and piles achieved the necessary capacity with sufficient factors of safety. Thermosyphons were installed near the foundations in order to limit the effects of climate change on the permafrost. The two to four wind turbines in each of the three villages are currently operational. Refinement of the design based on the pile testing from the first village to the third has decreased the cost of the tower foundations and improved our understanding of designing for warm, degrading permafrost.

Jan 1, 2010

By Erwin Stötzer, Renato Fiorotto, Wolfgang G. Brunner, Manfred Schöpf

"Deep mixing methods can be used economically for the construction of cut-off or excavation support walls where other systems such as traditional soldier beams and lagging walls would yie ld unsatisfactory performance, where the installation of vibrated or driven sheet piles could cause vibration induced settlements and where concrete diaphragm walls would be time consuming and expensive. The new CSM method can largely replace the more conventional single or multiple auger methods of soil mixing or jet grouting. The cutter tool is similar to a cutter used in diaphragm walls or cut-off walls and is operated with a Kelly mounted on a drill rig. With this system much deeper walls can be installed and even hard soil layers can be penetrated. CONVENTIONAL SOIL MIXINGIn 1962 Norman Liver patented an auger-based soil mixing technique that has become the basis for the world's current technology.The deep mixing method (DMM), as it is known today, is an in situ soil treatment and improvement technology where the soil is blended with binders and/or other materials that are introduced in a slurry or dry form.Typically one or more hollow, rotating mixing shafts tipped with some type of cutting tool are mounted vertically to the mast of a base carrier and are driven into the ground by hydraulic or electrically powered rotary heads. The shafts above the cutting tool may be further equipped with discontinuous auger flights and/or mixing paddles. The binder is injected through the hollow shafts to nozzles located near the cutting tool where it is mixed with the ground to form columns of treated soil.Individual column diameters range from 0,6m to 1,5m and may extend to 40 m in depth. They can be arranged individually or in contiguous or secant patterns to produce a wide range of treated soil structures on both land and marine projects. Typical configurations are: Single elements, rows of overlapping (secant) elements, grids, lattices and blocks (Fig. 1 )."

Jan 1, 2005

By Chu E. Ho, Alfredas Daugiala, Nicola Ebanks

"The construction of an ancillary structure for the new Second Avenue Subway Line in Manhattan, New York City involved a deep excavation in highly variable rock conditions adjacent to a fragile masonry building. The maximum difference between the lowest and highest rock elevations was about 30 feet, which posed a problem for the installation of secant piles that formed the supporting retaining wall for the excavation. At certain areas, the rock levels were higher than the top of the invert slab of the ancillary structure. To avoid disturbance to the adjacent fragile building, the secant piles were fully cased for drilling through the overburden soils and the rock sockets were formed using non-vibratory technique. This paper discusses the design and installation details of the secant pile wall and the contingency measures that were considered to mitigate the highly variable rock conditions. Monitoring of the adjacent fragile building showed that impact of pile installation were controlled within tolerable limits and safety of the building was not compromised.INTRODUCTIONThe 96th Street Station forms part of the newly constructed Second Avenue Subway Line on the East side of Manhattan Island, New York City (Figure 1). During construction of this station, several deep excavations were carried out adjacent to existing fragile buildings (Arksman et al. 2012, Grigson et al. 2016). These fragile buildings were typically four to five stories high, with a single rubble wall basement supported on timber piles or seated directly on the fill. The timber piles were often found to be in a poor condition and connections to the footings were compromised due to rotting of the timber within the zone of water table fluctuation. Several of these fragile buildings had to be strengthened and underpinned to improve the stability of the structures prior to commencement of excavation for the new subway station box (Trabold et al. 2012, Ho and Pena-Iguaran, 2013). The situation was most challenging at Ancillary Buildings 1 and 2 located at 93rd and 97th Street respectively, where secant pile walls were located merely 2 feet away from the adjacent property line, due to architectural space constraints. While mitigation of excavation induced ground movements can be controlled by the adoption of a stiff excavation support system, a more concerning factor was the uncertainty associated with the impact of the secant pile wall installation on the stability of the existing fragile buildings. This was particularly difficult at Ancillary 1 where the secant piles encountered highly variable rock levels that intruded into the excavation space. The following sections discuss the design and installation of the secant pile wall and contingency measures that were considered at Ancillary 1."

Jan 1, 2016