Search Documents

By Andrew Dobson, Cheryl Allen, Enrique Acuña

"Totten Mine return air raise was designed with two parallel fans equipped with silencers to reduce the noise emitted from the outlets into the environment. As development and production of the mine progressed through the past years, the silencer system needed to be upgraded, and additional maintenance strategies have been necessary to meet the regulatory noise limits enforced by the province of Ontario. The current mine plan will require the fans to reach the upper limit of their capacity by Q1 2019. To achieve this operational target, additional silencing capability has been required and Totten Mine has explored alternatives to further extend the noise silencing capacity available considering the current constraints at the mine site. The alternatives included a new silencer baffle design and a new layout that have allowed doubling the length of the silencer system. Using acoustic measurement data collected on several occasions, this paper presents and discusses the performance of the various silencing systems which have been installed on the return air fans at Totten Mine.INTRODUCTION Vale Canada Limited’s Totten Mine is a base metal, underground mine extracting nickel and copper, situated in the Sudbury Basin of Ontario. The mine initiated operations at the end of 2013, and is equipped with two main return air fans and two main fresh air fans located on surface. Both fresh air and return air fans are set in a parallel arrangement to operate as integrated units and are equipped with variable frequency drives (VFDs) to allow for the remote modification of their operating set point, usually between 600 to 880 rpm, depending on the mine’s requirements. The main return air raise (RAR) fans are also equipped with dissipative baffle silencers to attenuate the noise emitted to the environment. Approximately four years ago, acoustical measurements conducted to verify compliance with the applicable regulatory criteria, and respond to noise concerns from neighboring residents, concluded that the sound emissions of the main return air raise exceeded the noise design parameters. The acoustic tones of the fans were audible offsite, at a residential location, approximately 9 km northeast of the mine site. The elevated sound levels and offsite audibility was due to degradation of the original discharge silencers from moisture and particulate being drawn from underground workings and passing through the silencer baffles. The audibility was also due to an outlet directivity pattern which directed noise towards the residential location."

Jan 1, 2019

By G. S. Ospanova

The results of complex processing sulphide copper ore and advantages of recovery of copper by vat and heap leaching, sorption, cementation and electrolytic solutions processing and utilization of waste material after heap leaching of copper for production of building materials were investigated. The combined chemical solvents with the additives of oxidizing agents are developed at the KazNTU. The solvents are inorganic or organic chemical reagents, which form complexes of Cu, Au, Ag, Pt, Ni, Sr, Co etc. Recovery of non-ferrous metals from solutions and purification of industrial waste waters is carried out on the base of using new synthetic and natural sorbents (from local raw materials) which are able to bind ions in both cationic and anionic forms depending on type of ligands and external conditions. Optimum parameters of copper sorption were determined. The developed wasteless technologies of copper extraction from sulphide ores with usage of new non-toxic solvents and accessible sorbents with full recycling of water are tested in pilot scale heap leaching, and are recommended as the ecological, economical and practical alternative to traditional methods.

Jan 1, 2007

By Vladislava A. Ignatkina, Fillip O. Milovich, Vladimir A. Bocharov

"Complex research of flotation concentrates of monomineral fractions of chalcopyrite, sphalerite, galena, pyrite, pyrrhotite included methods of adsorption of collectors, surface compounds by IR ATR, and surface films of flotoreagents by TEM. They revealed that the proportion of the parts of thionocarbamate (TC) and dithiophosphate had an effect on the adsorption rate of the components of minerals, on the presence of characteristic bands, and, what is an important, visualized surface film of organic flotation reagents on the particles of concentrates by TEM. The predominance of thionocarbamate in a composition selectively increases the adsorption rate constant of the components and recovery of chalcopyrite compared with sphalerite and galena. The highest flotation rate using TC is characteristic for chalcopyrite (0.62 min- 1) in case of individual use, and it's in combination with butyl xanthate (25% butyl xanthate or 3:1) 0.89 min-1 too. We studied the ternary blend - dithiophosphate: thionocarbamates: butyl xanthate. The increase of the proportion of butyl xanthate in combination reduces the contrast of the flotation rate among all sulfides.Practice flotation of refractory sulfide copper-zinc ores of the Urals (content sulfide iron - 75- 95%) confirmed that the use of a combination of selective collectors increases selective recovery of copper sulfide minerals up to 50% at the first fraction that is the conditioned copper concentrate. New selective sulfhydryl collectors resulted in high levels of recovery of copper into a concentrate - more than 90% - against 70-72% (butyl xanthate) from copper-pyrite ore. Low floatability of iron sulfides has been obtained by selective sulfhydryl collectors. Using weak selective sulfhydryl collectors can reduce pH into collective or selective flotation from pH 10-10.5 to pH = 7.2-7.5, which improves the quality of individual concentrates of nonferrous metals and their recovery. The same is true for polymetalic sulfide ore. The volume of gold recovery also increased."

Jan 1, 2016

By Carl Lausen

Within recent years several mining companies have sent expeditions co the east end of Great Slave lake co determine the mineral possibilities of that area. Little was known of the geography of the region, and even less of the geology; and, not until Blancher's survey was made and the results published, was an accurate map of the lake available. Early explorers followed the Inconnu channel and the north shore of McLeod bay to Port Reliance, and, just prior to Blancher's survey, Hornby showed that the southern passage was feasible. Apparently, but few geologists have ? travelled through the country, for geological information is meager. In 1900, Robert Bell, of the Geological Survey, made a trip to Fort Reliance by way of the north shore of McLeod bay, and he gives a brief description of the geology. The present paper is the result of an expedition into this little-known region by Mr. Geo. M. Douglas and the writer in the summer of 1928. The south shore of Great Slave lake was followed to the east end of Tochatwi bay, and an extensive exploration was made of Kahochella and Pethei peninsulas. The prime object of the expedition was co determine the presence or absence of the copper-bearing Keweenawan basalts.

Jan 1, 1929

By C. Lambert

It has been shown that contacts between host rock and engineered barriers may be critical in the design of deep radioactive waste repositories. Water is expected to reach the interface zone after the re-saturation of the geological massive and its presence may lead to concrete leaching. Such a phenomenon could increase the interface transmissivity and compromise the confinement of radioactive waste. Recent experimental results from Buzzi et al. (2008) have enhanced how concrete leaching can drastically change the mechanical behaviour of such interfaces. Because of the local loss of strength resulting from leaching, shearing resulted in a degradation of the interface asperities. Similarly to rock joints, intact interfaces exhibit a usual contracting-dilating behaviour. On the contrary, depending on the extent of leaching, the degraded interface can display a fully contracting. This paper intends to investigate the influence of concrete leaching on the mechanical behaviour of host rock-concrete interfaces. The leaching process consists in the dissolution of some of the hydrates of the cement paste, leading to a reduction of the strength and Young's modulus. A discrete model has been developed with PFC3D where a simplified interface morphology has been introduced using a saw-tooth description of the asperities.

May 1, 2009

By N. Parnian

"Carryover of caustic soda (NaOH) in the steam path caused catastrophic failure of superheater 304H stainless steel tubes in a steam generator and led to an unexpected shutdown after just five months of continuous service of petrochemical following the start of production. The cause of the failure was studied, with a focus on the formation of sigma phase in the weld joint and effect of caustic embrittlement on stress corrosion cracking (SCC). The cracks were examined at the seam weld, heat affected zone (HAZ), and Ubend areas. Hardness was measured for the base metal, HAZ, and weld metal, and microstructures were examined using optical microscopy and scanning electron microscopy (SEM). Crack initiation is attributed to gouging on the precipitated carbide at the HAZ and also the formation of sigma phase in the weld metal, as shown by energy dispersive X-ray (EDX) analysis. In addition, cracking was propagated by caustic embrittlement because of residual stresses and hammering. Finally, the characteristic feature of fracture was illustrated by SEM fractography, and consists mostly of intergranular SCC and some quasicleavage transgranular. INTRODUCTIONThree key factors are needed for the initiation and propagation of intergranular stress corrosion cracking (IGSCC): a susceptible material, a corrosive environment, and sufficient stress. Although austenitic stainless steels are susceptible to sensitization and IGSCC, they are widely used in boiler and superheater tubes because of their high corrosion resistance, high oxidation resistance, acceptable mechanical characteristics at elevated temperatures, and low cost.Sodium hydroxide is injected to neutralize acidic constituents in the steam path, but caustic can concentrate in boiler tubes and attack the surface metal (known as gouging) even traces of caustic in the steam can deposit on surfaces and cause local concentrations of several percent (ASM handbook, 1992). Not only sensitized grains but also sigma phase formed in the weld metal can initiate caustic cracking. In this research, the cause of the failure of 304H stainless steel superheater tubes in a methanol petrochemical plant in Iran was studied with a focus on the effects of caustic embrittlement on IGSCC."

Jan 1, 2012

By M. Saghaeian, R. Hejazi, Fakoor Sanat Tehran Company, H. Abedini, M. Zare

"Dewatering of final tailings is one the biggest issues in iron ore processing plants. Because of the fine and hydrophilic particles in the iron ore tailings, dewatering of such material is difficult and, in most of the cases, needs to be processed using expensive and complicated equipment. In this study, a novel method based on classification of small and large particles has been proposed to improve the dewatering performance of iron ore tailings. In the proposed method, a hydrocyclone has first been used to separate the fine and coarse fraction of iron ore tailings. Then, the coarse fraction (hydrocyclone underflow) is easily dewatered by using vacuum belt filter. Then, the fine fraction (hydrocyclone overflow) is primarily dewatered by using a high rate thickener. Finally, the thickener underflow is added to the bed of solids on the same belt filter, which is used for dewatering of hydrocyclone underflow. The efficiency of this method has been compared with other solutions for tailings dewatering including changing vacuum filtration parameters, using fabric with larger pore size, and using pressure filtration, all through laboratory scale experiments on the tailings of an iron ore processing plant in Iran. The results indicated the superiority of this method compared to the other ones, which increased the specific filtration capacity of the tailings by around 46%.INTRODUCTIONWet beneficiation of minerals requires a substantial amount of water to enhance the efficiency of the process. Used water should be recovered at the end of process to minimize shipping costs, meet contract specifications, and reuse process water (Wills and Napier-Munn, 2006). Dewatering equipment is usually divided into sedimentation (thickening) and filtration (pressure and vacuum) equipment, the choice of which depends on particle size, solid content of slurry, and material nature (Mular et al., 2002)."

Jan 1, 2016

By H. Thomasson

This paper will deal with on-site maintenance welding using the stick electrode, electric arc process. It is primarily concerned with the underlying principles, the application of which, or the lack of such application, governs the success or failure of the operation. It will discuss first the base metal or item to be welded, including the field identification of its weld-ability and the determination of the procedures to be followed. Second, it will outline heat effects and the interrelation between heat applied as part of a welding operation and heat deliberately applied as part of a heat treating cycle, stressing the fact that in welding the same basic principles are effective. The third consideration will be weld metal and its control of both composition and properties. Last, but not least, distortion, shrinkage and residual stress will be considered and practical means for minimizing their adverse effects outlined.

Jan 1, 1967

By C. Blais, G. L’Espérance

Characterization of second phase particles is important with regard to their influence on mechanical properties of materials. Analytical electron microscopy offers the possibility to achieve complete characterization of inclusions. Complete characterization of inclusions means quantitative evaluation of their chemistry and the stereological parameters. A characterization technique based on integrated microscopy and involving scanning electron microscopy, image analysis and energy dispersive X-ray spectrometry is presented. A discussion of the use of transmission electron microscopy and electron energy loss spectroscopy is also presented for the characterization of very small particles and compounds (>100 nm).

Jan 1, 1998

By J. E. Gill

Introduction During the past summer, detailed geological mapping was extended to cover the entire group of 31 claims owned by Waite-Ackerman-Montgomery Mines, Ltd., and considerable new information was revealed by development and exploratory work underground. These new facts provide a more complete view of the lithology and structure of the area than has heretofore been available. They also necessitate revision of certain interpretations presented last year by Peale (l), and have served to straighten out some of the problems suggested by Porritt (2). The purpose of this paper is to outline in a broad way the relations as now understood and to discuss in detail certain points which should be of interest to members of the Institute. Maps and records by the mine staff have been freely used in arriving at the interpretation presented in the following pages. The writers are especially indebted to Mr. R. V. Porritt, the mine manager, with whom many of the problems touched upon were discussed on the ground and whose intimate knowledge of the geology of the underground workings aided greatly in testing various hypotheses. The writers have profited greatly, also, from close association with Dr. W. F. James during the course of the work. Permission to publish the included data has very kindly been given .by the management.

Jan 1, 1932

By K. V. Lindell

Introduction This paper describes a recent innovation in the design and construction of mine headframes. A reinforced concrete headframe was built by using sliding forms. A concrete headframe of conventional design was originally considered, but investigation of this project showed that it was doubtful if the bearing strength of the soil was sufficient to support the great weight of a structure of this type. In addition, the slope and the fractured condition of the serpentine bed-rock did not permit satisfactory piling. A conventional steel headframe with storage bins was then designed, but, due to the steel situation, delivery promises were set back many months. The concrete headframe was again investigated, and a design was adopted incorporating a circular headframe lower in height than that first considered, with skips discharging into a smaller surge bin. The upper section of the shaft collar was strengthened to result in a stable structure which would be supported by bed-rock, as well as by the concrete and steel lining of the shaft itself.

Jan 1, 1948

By S. Kelebek, B. Ingram, C. Gibson, T. MacNeil, M. Aghamirian

"The beneficiation and upgrading of pyrochlore from its ores is carried out through flotation. In industrial practice, upgrading is conducted in a two-stage flotation process in which pyrochlore flotation is carried out after gangue mineral pre-flotation (carbonate, silicate, sulphide or phosphate reverse flotation). In this study, the flotation of pyrochlore from a low grade carbonatite ore was performed at the laboratory scale following a two-stage flotation process in which carbonate minerals were floated in advance of niobium minerals. In parallel, a simplified flotation process was developed in which pyrochlore was floated directly from gangue minerals at increasingly acidic pH. Laboratory results indicated that both two-stage and direct flotation provided similar results in terms of niobium grade-recovery. Based on these results, a large scale, integrated pilot plant was conducted using a direct flotation flowsheet. While the elimination of reverse gangue flotation resulted in flowsheet simplification, the dissolution of carbonate minerals and the subsequent effect of dissolved cations on the floatability of pyrochlore added an element of complexity. A comparison of results from locked-cycle laboratory testing and pilot plant testing highlights the challenges of scaling up a complex flowsheet. A case is made for the direct flotation process and the key parameters to achieving success in large scale direct flotation of pyrochlore are discussed.INTRODUCTIONPyrochlore (Ca,Na)2Nb2O6(OH,F) is a niobium bearing mineral which has been the primary global source of niobium since the first pyrochlore mine commenced operations in the late 1960s (Gibson et al., 2015a). Preceding the discovery and development of high grade pyrochlore deposits in North and South America, the majority of global niobium supply came from gravity concentration operations of columbite (Fe,Mn)Nb2O6, across Africa (Perrault and Manker, 1981)."

Jan 1, 2016

By J. Budac, J. Dennett, D. Mayne, P. Nawrocki

"The Nickel/Cobalt operation in Fort Saskatchewan, Alberta has successfully used an oxidative ammonia leach process to refine a variety of feeds into high quality nickel and cobalt products for over 60 years. Fundamental changes to the refining process were made when the major feed was converted from nickel concentrate to cobalt rich mixed sulphides in the early 1990s. Since the early 1990s, the production capacity of the refinery has expanded to match increases in both mixed sulphides and other feeds. In addition to increasing the production capacity of the refinery, other changes have been required in order to improve the operability and reliability of the refinery as well as to deal with increasingly stringent safety and environmental requirements. This paper describes recent changes at the refinery including changes to the flow sheet, improvements in unit operations, incorporation of new feeds, management of byproducts, and control of impurities.INTRODUCTION The Cobalt Refinery Company (Corefco) plant in Fort Saskatchewan processes nickel-cobalt mixed sulphide intermediate produced at the lateritic nickel mine and high-pressure acid leach (HPAL) facility in Moa Bay, Cuba. Both operations are jointly owned and operated by Sherritt International and General Niquel of Cuba. The mixed sulphide, along with other feed materials, is processed at the Fort Saskatchewan refinery using a pressure ammonia leach-hydrogen reduction process to produce nickel and cobalt metal. This refinery was originally constructed in 1954 to treat nickel concentrate from Sherritt’s Lynn Lake mine in Manitoba. (Benson and Colvin, 1964; Boldt and Queneau, 1967; Forward, 1953; Forward and Mackiw, 1955; Kerfoot, 1989) From the mid-1970s until the early-1990s, the facility operated as an independent refinery, treating nickel-bearing feeds from around the world. The flowsheet was changed in 1992 to address the increased cobalt content of the feed. (Cordingley and Krentz, 2005; Kerfoot and Cordingley, 1997) The flowsheet was adapted further in 2009 to improve cobalt speciation in the leach process, which allows better cobalt-nickel separation. The 2009 iteration is shown in Figure 1. Three ammonia leach stages were used to ensure high recoveries of nickel and cobalt. Underflow solids from the final leach stage contained mainly iron oxides. One of the features of the leach process is the innovative recycling of ammonia. Ammonia vented from the leach process in tail gas and from atmospheric tanks is recovered and recycled into the refinery using water based scrubbers and a high pressure distillation process. Indeed, roughly 250 t NH3/d is recovered as distillate and recycled back into the process. Also, air enriched with ammonia which is vented from the later first stage autoclaves is recycled to the lead first stage autoclaves to maximize oxygen and ammonia utilization."

Jan 1, 2017

By A. J. Reed, W. R. Bergey, Carr. J. M.

"The Highmont copper-molybdenum deposits are at Gnawed Mountain in the Highland Valley porphyry copper district, 125 miles northeast of Vancouver. This district is near the center of the lower Jurassic Guichon Batholith, where a north-trending swarm of porphyry dikes is crossed by west-northwesterly structural belts in which fracturing, intrusion of porphyry and breccia, and mineralization areconcentrated.The Highmont deposits are 2 miles southeast of, and in the same southernmost structural belt as, the Lornex deposit. The main deposits occur on either side of a composite dike of granodiorite, porphyry and breccia which strikes west-northwestward in fractured quartz diorite. North of the dike, the adjacent Nos. 1 (East) and 2 (West) zones together contain 150 million tons of open-pit ore mineable in two separate pits. These two zones will support a 25,000-tpd mill with a grade in the first five years of approximately 0.46 per cent copper equivalent. South of the dike, the Nos. 3 and 4 zones are partly explored and will provide large additional reserves. In these various zones, chalcopyrite, bornite and molybdenite form disseminations and fracture-fillings accompanied by quartz, K-feldspar, tourmaline, sericite, specular hematite and other minerals. Bornite extends for varying distances north of the dike, beyond which chalcopyrite is locally accompanied by pyrite. Higher-grade mineralization tends to coincide with fracture swarms, or with shear zones and faults which largely parallel these swarms. The ore zones are reflected by geochemical soil anomalies which show some glacial dispersion. LP. surveys gave weak but significant responses, expressed as per cent frequency effect. The ore zones occur within a strong magnetic gradient, but do not show a significant magnetic response."

Jan 1, 1971

By H. A. Khorami, T. Wong, B. Velapatino, E. Asselin, T. Donnelly, E. Bryce, R. Dixon

A copper–nickel concentration gradient alloy was designed and fabricated through a powder metallurgy (PM) process. Copper and nickel powders were mixed with different weight ratios from 0 to 100% copper in 10% increments. Each powder mixture was poured inside a cylindrical die and compacted between two punches using a hydraulic press machine at pressures up to 70 MPa, resulting in approximately 1 mm thick layers (discs) of pressed Cu–Ni powder. These 11 Cu–Ni compacted powder layers, i.e. 0–100% Cu with 10% increments, were then compressed together with pressures up to 420 MPa to form a green part. The green part was sintered in a vacuum furnace at 1000°C for 10 hours to form a solid mass (PM part) of Cu–Ni concentration gradient alloy. In the sintering process, Cu and Ni particles fused together and formed a single piece due to diffusion of the atoms across the boundaries of the particles. The diffusion of atoms also converted the stepwise concentration change into a uniform concentration gradient. INTRODUCTION Copper has numerous applications in different industrial sectors due to its superior physical, electrical, mechanical and chemical properties such as its excellent thermal and electrical conductivity, resistance to fatigue, high ductility, and resistance to corrosion. Moreover, copper and its alloys have natural antimicrobial properties. This has opened up new applications for copper–based self–disinfecting surfaces in healthcare in an effort to mitigate healthcare–associated infections (HAIs). HAIs affect millions of patients each year, leading to significant morbidity and mortality as well as financial losses to healthcare systems (World Health Organization, 2016). HAIs spread through three main routes: (a) iatrogenic in which HAIs are a direct consequence of medical encounters and/or treatment; (b) person to person where organisms are transferred between healthcare workers, patients, and visitors; and (c) environmental where transmission occurs via contaminated surfaces and equipment (e.g. doorknobs, railings, toilets/commodes, medical carts). The use of antimicrobial copper–based materials on high touch surfaces could diminish pathogen transmission via this latter rout. This has subsequently led to the development of a variety of copper–based materials for use in healthcare settings and promoted the investigation of the antimicrobial efficacy of copper–based materials.

Jan 1, 2019

By H. M. Thurgood, F. A. Godfrey, F. W. Gilbert

This is a detailed presentation of the ancillary facilities, including power production, water supply, shiploading facilities, fire-fighting equipment, housing and community services. Additional subjects discussed include construction problems, townsite philosophy and staff organization.

Jan 1, 1968

By Yujing Jiang, Xuezhen Wu, Bo Li, Tomomi Iura, Gang Wang

"Yielding bolt has been widely used for rock reinforcement in mining and civil engineering in high stress conditions. However, the interaction mechanism of yielding bolt and matrix mass is still not clear at present, and no analytical model is available to predict its reinforcement effect quantitatively. In this paper, the mainstream yielding rock bolts were reviewed firstly. After that, a coupling model is proposed to account for the interaction between yielding bolt and matrix mass. Based on the plane strain axial symmetry assumption and the incremental theory of plasticity, equilibrium equations and compatibility equations of matrix mass, and also the response of yielding rock bolt are deduced theoretically. The proposed method was programmed in Visual Basic development environment, and a semi-analytical solution for the coupling model is achieved. The reinforcement mechanism of yielding bolt in conventional tunnelling is clearly demonstrated through an illustrative case study. The reinforcement effect of yielding bolt is estimated quantitatively, and the distribution of axial force along the bolt is presented. In addition, the validity of proposed method is verified by numerical simulations. INTRODUCTIONHigh stress in surrounding rock mass can cause serious stability problems such as massive squeezing in soft rock and rock burst in hard rock. It is observed that many conventional rock bolts failed when experiencing large displacement, which implies that they are too stiff to sustain large deformation and dynamic conditions (Stillborg, 1994; Hoek et al., 1995). Yielding bolt, which can also be called energy-absorbing bolt, has been widely used for rock reinforcement in mining and civil engineering for these conditions (Neugebauer, E., 2008). This paper focuses on the static reinforcement effects of the yielding bolts with analytical method and numerical simulations."

Jan 1, 2015

By Tuomas van der Meer, Jukka Tanninen, Annukka E. Mäkinen, Mika Martikainen, Laura M. Nevatalo

The mining industry consumes huge water volumes and the waste streams typically contain sulfate, which has caused problems to many operations around the world. Discharge of sulfate to fresh waters is being restricted as the sulfate load increases salinity and causes problems when sulfate is reduced to toxic H2S by natural bacteria. To reduce fresh water consumption, internal water recycling had become a necessity in metallurgical processes. However, the recycling causes accumulation of sulfate and other components in water, causing problems to process performance and increases scaling in piping and equipment. Few technically feasible water treatment processes exist in the market that can be applied to decrease sulfate concentration below gypsum saturation level: biological sulfate reduction, membrane separation, ion exchange, evaporation and chemical precipitation. Some of these technologies are effective for treating wastewater, but there is typically a highly concentrated sulfate fraction left requiring still further treatment. Outotec has developed a sulfate removal solution, Outotec Ettringite process, which allows flexible control of residual sulfate concentration, thereby opening doors for increased water recycle within processes and control of the sulfate in discharged waters. In this article the results and benefits of this novel process along with examples of operating costs are presented.

Jan 1, 2014

By M. Aushouri, S. H. Mansouri, N. Aminizadeh

A thermo-chemical model of the Peirce-Smith copper converter has been developed to predict the molten temperature. The primary assumption of the model was that all matte, slag and gaseous phases in the converter were in thermal and chemical equilibrium. In this model, the matte components were considered only as copper, iron and sulfur elements. In the slag making stage, all the reacted iron was converted to fayalite. The reaction rate of iron and oxygen in this stage was considered to be constant. The converter temperature was calculated by heat balance over time. The model was validated by a detailed comparison with measured industrial data. A good agreement was obtained. The converter temperature depends on process parameters such as oxygen efficiency and molten emissivity.

Jan 1, 2007

By K. S. Fraser, H. J. H. Pieterse

"A pressure oxidation plant to pretreat refractory sulphide ore at the Goldstrike plant in Nevada, was commissioned in early February 1990. The plant, with a nominal capacity of 1363 t/d, was commissioned over a one-week period and achieved design capacity and availability within ten weeks an unusually short period for a plant of this complexity.The pressure oxidation process is conducted under elevated temperature and pressure conditions, and in a corrosive environment. These conditions demand that the process and engineering design of the plant be carried out in a much more sophisticated and detailed manner than is normally required in a conventional gold plant.This paper provides an account of the process and engineering design of the Goldstrike pressure oxidation plant with special emphasis on the design of the vessels, slurry pumps, piping, valves, and control systems.BackgroundLocationThe Goldstrike property is located in Eureka County in northcentral Nevada on the Carlin geological trend. The mine is approximately 40 km northwest of the town of Carlin which is situated on Interstate Highway 80. The minesite is located 1700 m above sea level in the Tuscarora Mountains.Initial Goldstrike OperationsShallow, low-grade mineralization was discovered by diamond drilling in the Goldstrike area in the 1960s. A heap leach operation was established in the mid-I970s by the previous owners. The Post deposit was discovered in 1982. Gold production by mining and heap leaching reached I t/a (40 000 oz/a). American Barrick purchased the property in 1987 and started an aggressive program of deep drilling. This led to the discovery of the Betze and Deep Post deposits and established sufficient reserves to justify an initial 4100 t/d mill and a 5 500 000 t/a heap leach operation"

Jan 1, 1992