Search Documents

By C. H. Bertoni, A. Vachon

The Corner bay copper deposit is the first significan discovery on the south limb of the Dore Lake Complex, located at the eastern end of the Detour Lake-Chibougamau greenstone belt, Quebec. The deposit was discovered in March, 1981, after 26 years of intermittent work in the area. Mineralization is found in a shear zone cut ting rocks ranging in composition, from gabbroic anorthosites to anorthositic gabbros which have been intensely altered and deformed by at least two tectonometamorphic events. Both the copper-bearing shear zone and its host rocks are cut by a large NE-striking gabbro dyke. Most of the known mineralization is found east of the dyke, but two deep exploration holes have shown that the down dip extension is present to the west of the dyke. The mineralized shear varies from one to 15 metres in width, strikes around 010° and dips from 70° to 80° to the west, and has been tested for a length of 700 metres. The wall rocks are usually chloritized and silicified. Mineralization is characterized by chalcopyrite, pyrite, molybdenite, magnetite, and sphalerite occurring mainly as the matrix to quartz-carbonate breccias in the "main" shear zone. The predominant sulphides are pyrite and chalcopyri te as crystals or fragments. The brecciated mineralized shear shows evidence that there was at least one remobilization of the shear and it is suggested that copper-bearing fluids invaded the shear during its remobilization. The exact timing and source of mineralization are not known. Up to February 1984, 38 holes had been drilled to outline indicated reserves to a depth of 450 m of 1,5 million tonnes grading approximately 4% copper, 0.34 gm, gold and 13.71 gm silver per tonne. It is believed that there is considerable reserve potential in the block west of the gab bro dyke, the down dip extension of the main zone.

Jan 1, 1984

By J. P. Mogan, E. D. Dainty, A. Lawson

"The toxicity reduction of emissions from two diesel engines by the emulsification of water into fuel oil was investigated to determine the applicability of such systems to underground mining machinery. . The engines studied were: 1) the Deut; F6L7J4, four-stroke, air-cooled, 6-cylinder, V-configuration, indirect-injection (IDl) engine, and 2) the Detroit Deisel Allison Division 8V7JN, two-stroke, water-cooled, 8-cylinder, V-configuration, direct-injection (Dl) engine.The application of emulsified fuel treatment to the two-stroke engine did not prove to be practicable. In the case of the Deutz engine, however, substantial benefit resulted. For a modest J5 per cent water content in the fuel and an injection timing of24° BTDC, approximate reductions of40 per cent in the concentrations of both particulate matter and nitric oxide (NO) were produced. These reductions were accompanied by insignificant changes in other toxic constituents. The net result was an approximate 30 per cent reduction in the over-all exhaust toxicity for typical LHD operation as assessed by the Health Effects Index criterion. This toxicity reduction represents a significant advance from the points of view of an improved underground environment and/or reduced ventilation costs."

Jan 1, 1981

By I. P. Barbosa, P. S. M. Soares, I. O. C. Masson

"Permanent magnets have been applied extensively to several electronic products such as printers, TV sets, microphones, microcomputers and headphones, presently manufactured in large scale by industrial economies. Sm-Co alloys represent about 20% of the world market for permanent magnets and their industrial processors generate 20-30% of magnetic scraps which can be recycled. This paper discusses a process route to recycle SmCo5 using acid treatment, solvent extraction of Sm and electrowinning of Co. The results confirm the feasibility of the alternative proposed. Basic operational variables are suggested as guidelines to design a plant for recycling magnetic scraps.The use of hydrometallurgical processes to recycle scraps from the industry of permanent magnets has been suggested in some recent papers related to recycling of metallic alloys [ 1 ]. These research efforts might be understood as a worldwide tendency towards the development of self sustainable metallurgical processes which mean the reduction of environmental impacts.CETEM -Center for Mineral Technology leads in Brazil several research programs concerning recycling and treatment of industrial residues. The work on samarium purification and concentration by solvent extraction, producing also a solution of cobalt sulfate as partially reported here is one of these programs. Previous results related to the sulfuric acid digestion of SmCo5 are presented somewhere else [2]"

Jan 1, 1997

By C. Derek Martin

"Predicting the ground response for tunnels in weak shales remains challenging. Predicting the ground response is challenged by difficulties in characterising the material, and our ability to predict deformations that are driven by coupled hydromechanical processes, when this material yields. The techniques that are used for characterizing weak shales are reviewed, and three case histories are examined that demonstrate the behaviour of these weak rocks during tunnelling. A general framework is provided for assessing the squeezing potential for weak shales.1 INTRODUCTIONGeologically, shale is an argillaceous fine-grained sedimentary rock that forms from the compaction of silt and clay-size mineral particles commonly referred to as ""mud"". Because of this grain size, the material is generically classed as Mudstone (Figure 1). Shale is distinguished from other mudstones because it is made up of many thin layers (laminated) and readily splits into thin pieces along the laminations (fissile). While the geological classification of shale appears straightforward, the classification for engineering purposes is often confusing. Underwood (l967) provided the first description of shale that made the distinction between “soil-like” compaction shales and “rock-like ""cemented"" shales. He coined the term ‘clay shale’ to capture the characteristics of hard clay yet recognizing its origin as a shale. In this paper weak shale is synonymous with clay shale and have strengths that typically range from R1 to R2 (1 to 25 MPa). Characterising these materials draws on methods from both soil and rock mechanics."

Jan 1, 2015

By Luis Castelli, Aldo Bonomelli, Giselle Schifferli, Claudio Zamora

"This paper introduces the operational concept and the description of a multi-site Remote Support Center for knowledge management and long-term process performance improvement.This centralized Support Center provides real-time monitoring of open-platform process automation systems, and on-line access to process data and control applications information for multiple sites.Considering that process automation is a key enabler to business performance improvement, sustaining effective performance benefits over time becomes essential. Unfortunately, changes in manufacturing process dynamics, technology obsolescence and in plant operational practices cause the control strategies to lose their effectiveness over time unless their performance is periodically evaluated, and if required, tuned to the new process conditions.A new concept in process automation is proposed through the addition of a new control loop based on performance analysis methodology which is intended to feedback process and automation operation information to system and process specialists, allowing for continuous manufacturing process improvement and sustainable production benefits through effectual control strategies.A remote support center can play a key role in the delivery of such services, by providing the base platform from which a comprehensive process overview and a centralized knowledge database can be executed and additionally, as an enabler for plant operational practices change.INTRODUCTIONA Benchmark on Automation Level in Copper Concentrators conducted by AMIRA in 2004, reported that the Codelco divisions scored below their peers in several categories.Codelco had thereafter been looking for a new automation concept, and had focused on process automation as a key enabler for process manufacturing and business performance improvement. The final decision was to create a strategic alliance with a world-class automation technology provider.The traditional approach based on isolated automation solutions/projects, showed that the control strategies benefits were decreasing progressively over time, because of the on-going need to adapt the control models to the ever-changing process conditions and different plant operational practices. Another consequence of this traditional approach was the wide variety of technologies and automation systems deployed in the different plant sites, with no common automation standards, and with low opportunities to transfer knowledge or practices."

Jan 1, 2010

By R. Marleau, R. Assad, J. Dugas

"A study of the geological features of known occurrences of mineralization in Gaspe is the basis for a classification. Nickel, chromite, asbestos and some copper are pre-or syn-Taconic, whereas the most important deposits are tied to granitic post-Taconic stocks. Most occurrences are clearly related to igneous rocks: nickel, chromium and asbestos to Ordovician serpentinite; copper to volcanic rocks of different ages; and copper, zinc and lead to acidic intrusions with apparent zoning. Some lead-zinc deposits lying between the Grande Greve and York Lake formations are stratigraphically controlled. Some occurrences are tied to faults; e.g., the nickel-copper mineralization along the North Grand Pabos fault. Northerly-trending transverse structures appear to coincide with the Gaspe Copper, Mount McGerrigle (Tabletop) granite and Lemieux dome areas of mineralization. JEAN DUGAS, after graduating"

Jan 1, 1969

About MAC ? The national organization of the Canadian mining industry ? Mining, smelting and refining of base and precious metals ? Mining of iron ore, diamonds, uranium, oil sands, coal and industrial minerals ? Many associate members ? www.mining.ca

Aug 1, 2013

By M. W. Lewis, J. Werner

Fluctuating metal prices, declining head grade, and increased operational costs are forcing many open pit mining companies to look to their balance sheets for significant cost reductions in order to remain competitive. Maintenance continues to represent a significant proportion of the total operating costs in the mining industry. Compared with the other major cost components of the mining process, very little effort has gone into maintenance optimization. The potential payoff from maintenance optimization on the cash cost of the commodity is enormous. A large percentage of these costs are incurred in unscheduled maintenance events, which typically cause serious disruptions to the production process. These maintenance-induced production losses can be a significant contributor to the overall operating costs. A structured proactive maintenance approach using the latest advances in technology can achieve dramatic cost reductions and productivity improvements. Remote condition monitoring systems are becoming increasingly commonplace and have the potential to identify problems prior to failure. Detection of equipment degradation prior to failure will enable repairs to be scheduled thereby reducing costs and interruptions to production. Remote condition monitoring technology has evolved rapidly in recent years, with a host of new tools becoming available to assist mine operators in improving their maintenance operations. These tools have capabilities such as remote real-time vital signs and performance monitoring, alarm/event handling, trend analysis, and maintenance workflow management. When these monitoring tools are used in conjunction with a mine management system, the vital signs data can be integrated and associated with maintenance history, predictive maintenance data, operational information, and geographical information. This integrated approach to the management of vital maintenance data will help shift the mobile equipment maintenance paradigm from reactive to proactive. This paper will introduce a proactive approach to the management of the maintenance process and the tools required to facilitate this process.

Jan 1, 2005

"The Key Lake mill was commissioned in 1983 to process the two Key Lake ore deposits. With the depletion of these ore bodies in 1999, the plant was converted to mill the exceptionally rich McArthur River deposit located seventy eight kilometers northeast of the Key Lake mine site. This paper describes in detail the Key Lake milling process. The mill consists of a grinding circuit, a leachkounter current decantation circuit, a solvent extraction circuit, a yellowcake precipitatiodcalciner circuit, an ammonium sulphate crystallization circuit, and a waste treatment circuit. The paper also describes process changes to handle McArthur River ore, including the ore receiving stationLOCATIONThe Key Lake mill is located 78 kilometres south of the McArthur River mine. It is located at latitude 57' N in northern Saskatchewan, within the southern boundary of the Athabasca formation. The nearest town is Pine House, located 240 kilometres to the south. Access to the mine is by an all weather road and by a private airstrip.HISTORYAND DESCRIPTION OF OPERATIONThe Key Lake mill was commissioned in October 1983 to process ore from the Gaertner and Deilmann ore bodies. The mill was designed to produce twelve million pounds of uranium oxide (U308) a year from a feed grade of 2.4% U3O8.Following grinding, the uranium is leached in a two stage leach circuit using oxygen and sulphuric acid. An eight-thickener counter current decantation (CCD) circuit is used to separate the uranium bearing solution from the solid waste residue. The uranium is further purified in a solvent extraction circuit and then precipitated using ammonia. It is then calcined at 840' Celsius, and packaged into drums for shipping to refineries. There is a crystallization circuit to recover ammonium sulphate produced in the process and a waste treatment circuit."

Jan 1, 2001

By C. Cornejo, C. Schuffeneger, J. Rosas

"At the end of 2010 the AMSA Esperanza Concentrator started commissioning. Located in the Atacama Desert this project is the first of several large size concentrators developed recently to operate in Northern Chile. In addition to the new operations to be implemented in the short term, many existing installations are planning expansions. The use of large size equipment is one of the common characteristics of the new concentrators, but also new technologies are being considered and innovation is present in most cases. Sea water or desalinated water will be required to process large tonnages of sulphide copper ores as well as gold bearing ores, since process water supply from the Andes will no longer be available. The high cost of sea water or desalinated water supply and the high cost of energy are not a limitation as the current metal market scenario allows obtaining an attractive NPV even from installations designed to process relatively low grade ores. A review of the current concentrators being developed in Chile is presented, including a description of the main design issues related to technology and innovation. An analysis of the Chilean mining industry is also presented, detailing mine and plant capacities as well as expected final products.INTRODUCTION The mining sector in Chile has become a reference when analysing the large concentrator plants projected or currently in operation all over the world. At present and as a consequence of the high price of metal commodities, most South American countries have an active mining sector. Chile is known as a major producer of metals. First records of copper production exported to Spain are dated to the early XVII century. Since then Chile has produced over 13% of the total copper ever produced in the world. After 1990 Chilean mining and the associated cluster of activities has substantially grown to levels never reached before, especially in the production of copper, gold and other non-metallic minerals. This dramatic increase is the result of an economic policy based on delivering comparative advantages and incentives for the admission of foreign capital to offset the weak domestic investment in previous decades. Massive mining of its huge mineral resources has allowed Chile to be a world leader in the production of copper and other base metals and mineral products."

Jan 1, 2012

By A. Eltringham

Operations downstream of mining and beneficiation are still being subjected to increasing scrutiny as highly capitalized projects have been either slow to achieve their targets or have actually failed to do so. Leaching and smelting projects have fundamentally high calls on capital and technology as reaction rates are increased and the capture and disposal of unwanted products are subjected to greater restrictions. Separating value from waste inherently becomes riskier as the purification of the desired product imposes greater demands on the process to produce benign wastes. When we superimpose on the chemistry of the project severe predictions of throughput rates, that bring in facets of manufacturing, we are introducing complexities that the records show are not handled well. This paper discusses some of the more common challenges that operators face and what methods are available and are likely to be successful in preventing the loss of value as projects are brought on-stream. This thinking needs to start much earlier and at greater intensity than our industry has normally chosen to employ.

Jan 1, 2011

By Alice H. Zhu

Belt conveyors are widely used in materials handling industries. The bulk materials which can be transported include ores, coal, earth, grain, limestone, wood chips, fertilizer components such as potash and many others. Along with the new technology development and enhanced industrial automation requirements, belt conveyor instrumentation has also been modernized to improve conveyor availability and performance. Traditionally, belt conveyors are equipped with emergency pull cord switches to shut the conveyor down, misalignment switches to signal the belt offline condition, speed sensors to detect the belt slippage, and level switches to prevent material plugging in the discharge chute. Belt rip detectors are also normally provided for long belt conveyors. As a rule, equipment condition monitoring is not automated at most operating facilities, but is performed manually by maintenance staff via time-based surveillance. The new generation of condition monitoring instrumentation and control equipment can be successfully utilized to design a reliable, cost-effective, and centralized monitoring system, capable of monitoring a wide variety of mechanical equipment. The implementation of the condition monitoring automated system can provide continual monitoring of the plant equipment to ensure safe operation of the equipment to its required capacity. Any abnormal behavior of the motors, gear reducers and pulleys can be analyzed, alarmed, and recorded immediately, so problems can be detected and resolved before critical components failure. Therefore, the current trend is to provide the belt conveyors with condition monitoring system in addition to the traditional instrumentation, where temperature probes and vibration sensors can be installed on motors, gear reducers and all pulleys. Another innovative development is a three-in-one type belt rip detector which combines laser, tray and cord type detection together to ensure a prompt belt tear indication. The purpose of this paper is to present the latest development of belt conveyor instrumentation and introduce the application of newly developed instruments.

Nov 1, 2011

By A-A. Bogno, Ch. -A. Gandin, A. Maitre, H. Henein

Most metallic materials are produced from their liquid state. In order to control the properties of industrial products, it is very important to understand their solidification path and the resulting microstructures which can be significantly affected by melt undercooling. High undercooling results in rapid solidification and a refined microstructure with minimal microsegregation. This paper reports on the analysis of rapidly solidified Al-Cu droplets obtained by a single fluid atomization process, Impulse Atomization. A quantitative analysis by Rietveld refinement method of the Neutrons Diffraction data was carried out to determine the fraction of the intermetallic Al2Cu. Knowing the fraction of Al2Cu, the eutectic fractions and corresponding dendritic and eutectic undercoolings were estimated using the metastable extensions of solidus and liquidus lines of the Al-Cu system calculated by Thermo-Calc. In addition to this work, a model of microsegregation coupled with ThermoCalc software via TQ (application programming interface of ThermoCalc) and the Wang-Beckerman model for dendritic growth velocities has been developed for binary alloys. This has led to the development of a phenomenological relationship between primary phase undercooling and initial growth velocity. A comparison of estimated primary undercoolings using a coarsening model with the adiabatic undercoolings for each alloy composition has confirmed that solidification occurs under adiabatic conditions during recalescence.

Jan 1, 2014

By D. Sprott, P. A. Kirsch, J. Harris, D. Cliff

This paper details the work of RISKGATE, the largest Australian Coal Association Research Program (ACARP) occupational health and safety initiative to date. The program is an interactive online risk management system developed to maximize health and safety performance in the coal mining industry by implementing continuous improvement in managing major unwanted events. The comprehensive knowledge base covers tires, collisions, fires, isolation, strata control underground, ground control open cut, explosions, explosives, manual tasks, and slips/trips/falls. All major Australian coal mining companies contributed topic experts to this broad industry initiative: nine coal mining companies, more than 80 experts, and more than 400 days of individual time for knowledge-capture workshops.

Jan 1, 2014

By R. Barbaroux, B. Dubreuil, D. Lemieux, K. Nasrallah, G. Garcia Curiel

"As conventional, base or precious metal ores are being depleted worldwide, the mining industry is being faced with an increasing exploitation of arsenical sulfidic ores. Enargite is a common example. The downstream processing of these ores poses several problems ranging from high smelter penalties to finding economical and environmentally acceptable means of disposing of the arsenic. Several hydrometallurgical processes have been proposed for extracting arsenic from enargite concentrates, notably using alkaline sulphide leaching (ASL). However, few alternatives exist for removing the arsenic from solution and stabilizing it in an approach that is both economical and environmentally acceptable.Dundee Sustainable Technologies (“DST”) has developed a technology for the sequestration of arsenic by vitrification. Originally optimized to cost-effectively stabilize arsenic trioxide (As2O3), DST has shown that vitrification could be successfully extended to the stabilization of other arsenical products, such as calcium arsenate (Ca3(AsO4)2) and sodium arsenate (Na3AsO4). In this paper, the vitrification of arsenic in the context of an enargite leaching was newly explored and demonstrated successfully.Two processing routes are being proposed by DST for the removal of arsenic from enargite concentrates and their stabilization by vitrification. In one route, arsenic is extracted by ASL and is then precipitated under atmospheric conditions and with minimal use of reagents and time. The resulting precipitate is an unstable hydrated ferric arsenate (FeAsO4•2H2O) that is then vitrified in a non-dilutive method, significantly increasing the stability of arsenic and meeting the TCLP guideline. Unlike is required for scorodite, stabilization was successfully achieved without concern for the crystallinity of the precipitate."

Jan 1, 2017

By Arun .. J. Basu

The paper introduces Intelligent Air Management (IAM) as the core activity of M&I Group of Companies (M&I) for providing a total solution to any air management problems for mining and mineral processing operations implementing a comprehensive systems approach through a world-wide network of strategic alliance partners and in-house engineering team and manufacturing facilities in Mississauga, Ontario, Canada. Recommendations for energy-efficient ventilation in a vibration and noise free environment are made with the patented and innovative solutions supported by extensive computational fluid dynamics (CFD) studies. The solution scope extends from an intelligent and integrated exhaust silencer to a complete ventilation sys-tem solution including inlet and outlet control design and ducting for diffusers and silencers.

Apr 1, 2005

By David Seaman, J-P Franzidis, Emmy Manlapig

"A new device has been developed to directly measure the bubble loading of particle-bubble aggregates in industrial flotation machines, both mechanical flotation cells as well as flotation column cells. The bubble loading of aggregates allows for in-depth analysis of the operating performance of a flotation machine in terms of both pulp/collection zone and froth zone performance. This paper presents the methodology along with an example showing the excellent reproducibility of the device and an analysis of different operating conditions of the device itself.The device has been used to investigate the froth selectivity of attached particles. Simultaneous measurements were made using a different froth recovery measurement technique in the same flotation cell. A comparison of these techniques shows that in this case, particles are selectively detached from bubbles at or near the pulp-froth interface.INTRODUCTIONA flotation cell can be considered to operate in two distinct phases or zones; namely the pulp or collection phase and the froth phase. The pulp zone is responsible for the formation of hydrophobic particle-bubble aggregates, whilst the froth phase is responsible for the separation of these aggregates from surrounding suspended hydrophobic and hydrophilic particles. Thus, the froth phase is the grade determining phase in flotation. A measurement of the bubble load (the mass of particles attached to air bubbles in units of mass/volume) will enable the analysis of the performance of both the collection zone at creating bubble-particle aggregates and also the froth zone at separating these aggregates from surrounding pulp.A measure of froth zone performance that has been used extensively in flotation research is the Froth Recovery, Rf, of a particular system. Froth recovery is defined as the mass of particles collected in the concentrate launder by true flotation as a fraction of the mass of particles entering the froth phase. The measurement of bubble load allows for this term to be calculated easily, rather than having to go through the laborious task of, for example, changing froth depths to determine this performance criterion (Contini et al., 1988; Vera et al., 1999b; Feteris et al., 1987)."

Jan 1, 2004

By Staff

One hundred thousand miles of flying over the North country without a single air casualty; much of it over virgin territory probably never before visited by white men; some of it over regions that abound with possibilities for minerals; all of it effective, for exploration and the establishment of bases and supply-stations, and for the carrying of men and their tools and provisions- this, briefly, is the record of Northern Aerial Minerals Exploration, Limited, a Canadian company organized Jess than nine months ago, which has been functioning, without interruption, during spring, summer, and now into winter. Our planes have ranged from the Alaskan boundary on the west to the Labrador coast on the east, and from the Transcontinental railway north to the Arctic circle. Our prospectors, carried on trips of hundreds, and occasionally thousands, of miles, have gone over large sections of country which were never before explored, and at the end of the prospecting season the Company finds itself in possession of several groups of important gold claims, which look most promising. In addition to this, we have been in contact with deposits of almost every known mineral.

Jan 1, 1929

This paper discusses how elemental analysis of conveyed bulk flows in real time using PGNAA (Prompt Gamma Neutron Activation Analysis) technology has resulted in significant improvements in advancing plant control in mineral processing operations. Basis of operation of the PGNAA through belt, full stream, continuous, multi-elemental, real time analysis technology is explained. Capabilities and limitations in plant operating environments are discussed including comparison with other real time, online technologies through review of published information available for on-conveyor minerals applications. Case studies demonstrate benefits provided by this technology in two operating mines. An iron ore company had prior experience with the PGNAA analyser technology, implementing an early model in a minerals application in 2003 to develop confidence in its measurement performance and usefulness of the data. A number of analysers were subsequently included throughout the new plant design for extensive measurement and control of conveyed bulk flows, from conveying after mining through to rail load-out. A copper-gold company installed an analyser to address copper ore blending issues where an on-belt system was the only viable option for the degree of control required. Analyser suitability was evaluated through test work on site samples to determine customised multi-element precision guarantees for each application. Analyser results from normal operation are compared against laboratory analyses of multiple cross stream samples collected from conveyed flows to assess performance. Both projects discussed were able to realise benefits previously unattainable for plant quality control, surpassing capabilities of traditional technologies which were either unsuitable for measuring conveyed flows with adequate accuracy or in real time. Equipment payback within a few months was achieved for both sites. Through proven performance in these applications, the companies consider the technology an essential component in advanced plant control necessary in new process flow sheet designs, rather than an optimisation tool.

Jan 1, 2014

By Adrian Daniel

"Dating back to 1934, Con Mine is located directly south to the city of Yellowknife in the NWT, Canada. With mill operations ceasing in 2004, a challenging surface remediation situation resulted which required the treatment of close to 40,000 m3 of Arsenic impacted material.Through much of the period of 1941 to 1970, Con Mine treated their refractory arsenopyrite ore through the use of an Edwards Heath roaster. With mounting environmental pressure and through Canadian governmental studies during 1950 to 1970, attention was directed to the Arsenic Trioxide material being collected by two Doyle scrubbers on the Con’s roaster stack. In 1970, the roaster was decommissioned leaving the resulting Arsenic material in two containment areas on surface.As a result of Con Mine entering into remediation in 2004, the Con’s autoclave, commissioned in 1992, was dedicated to the immobilization of high impacted Arsenic material through the combination of excess Iron under high temperature and oxygen overpressure. Examined, herein, is the history and chemistry of the Con Mine autoclave as well as the two stages of chemistry for the Water Treatment Plant used to remove arsenic, heavy metals and WAD cyanide from tailings water. Simplified capping plans of the tailing containment areas and a high arsenic impacted area are also presented.INTRODUCTION TO CON MINECon Mine (Con) is situated just south of the City of Yellowknife in the North West Territories (NWT) Canada and is bounded locally by Yellowknife Bay (North Extension of Great Slave Lake) to the east and Kam Lake to the west (Figure 6). The discovery of gold at Con was made in 1934 and mineral rights were acquired by Consolidated Mining and Smelting Limited (Cominco) and Falconbridge soon thereafter. Nerco Minerals Limited (Nerco) took control in 1986 and in 1993, was subsequently sold to, Miramar Mining Corporation which in turn was purchased by friendly takeover involving Newmont Mining in November 2007 as a result of acquiring the Miramar’s Hope Bay project. Con’s underground operations ceased in September 2003 and have since entered into the remediation of the site. The current surface lease holdings are about 340 Hectares (Table 1) which sits on top of the Archean-aged Yellowknife Greenstone Belt."

Jan 1, 2009