Search Documents

Jan 1, 2004

The purpose of this paper is to describe briefly the clean-up procedure adopted at the treatment plant of Paringa Mining & Exploration Co. Ltd. at Kalgoorlie, Western Australia.A clean-up is carried out at the end of each four-weekly period, and all figures subsequently quoted are taken from a summary of the results of the eight periods ending 8th April, 1941.STRAKING AND AMALGAMATIONOf the total gold won 22· 77 per cent. is recovered by straking and amalgamation.The discharges of both the primary and secondary ball mills are pumped over a common set of five ten feet long by three feet wide straking tables, set at an angle of 10 degrees, before passing to the 14 ft. diameter by 30 ft. by 8 ft. Dorr bowl classifier.This classifier is in closed circuit with both of the ball mills, hence the whole of the circulating load of the fine grinding circuit, which approximates to 800 per cent., is required to pass over the straking tables. For convenience in handling, corduroy cloths are used in lengths of 5 feet, and are picked up and replaced by clean cloths at four-hourly intervals. The avaHable straking area provided is, therefore, 900 square feet, or approximately 3·30 square feet per original ton per 24 hours. The density of the pulp passing over the tables is about 54 per cent. solids, the area provided per ton of pulp per 24 hours being approximately o· 2() square feet. Washing of the corduroy cloths is carried out on the day shift only, about 800 lb. of strake concentrate being obtained daily.This concentrate is sluiced from the washing trough on the elevated straking floor to the 4 ft. by 2 ft. diameter amalgamating barrel located in the gold room below.The barrel is of standard design and is rotated at 25 r.p.m. It is charged each day at 4 p.m., and grinding of the strake concentrate at approximately 70 per cent. solids is continued until 8 a.m. the following day. The barrel is then stopped, and the contents generously diluted with water, and after a few minutes rotation some of the slime is carefully poured off through the small discharge hole. This dilution and decantation is repeated until a good deal of the valueless slime has been removed.A further quantity of strake concentrate is then charged to the barrel, which is allowed a further 16 hours grinding period. After again diluting and decanting, approximately 25 lb. of mercury and 15 lb. of lime are added to the charge, which is then given an amalgamation period of 2 hours before cleaning up.By the process of grinding, diluting and removal of slime by decanting...

Jan 1, 1941

Mineral formations, accumulated during technogenic activities greatly influence an economic and ecological situation in the Kola North. On the one hand, the dumps from extraction of mineral resources, tailing ponds of beneficating plants, ash dumps, wastes of metallurgical and mechanical engineering productions destroy the regionÆs environment and require taking certain measures and costs to bury or protect from weathering, oxidation, etc. On the other hand, technogenic mineral formations contain a lot of valuable scarce components. The amount of solid wastes increases annually, causing damage to ecology and economy. Researches conducted in recent years showed a possibility and economic expediency of comprehensive processing of wastes from different enterprises in Murmansk region and their use for production of new competitive commodity output, possessing high consumer properties. Thus, involving mineral wastes from Khibiny apatite deposits into hydrometallurgical industrial processing provides the basis for setting up a large beneficating-metallurgical complex. In this case ores and wastes from other deposits on the Kola Peninsula, containing titanium, rare, rare-earth and other valuable elements, may be involved into processing. Establishing such a complex will allow to organise a deep processing of natural resources, utilise some production wastes, improve ecological security and supply production with competitive output. Expanding the complex implies not only involving new mineral raw material into processing, but mainly deepening raw material processing, maximum utilisation of local natural resources and obtaining a wider variety of prime products.

Jan 1, 2002

By H Saw, M Cordova

Cemented rock fill (CRF) is often used to support open stope voids. This allows for the full recovery of ore while achieving global mine stability. In such cases, the exposed CRF masses require adequate compressive strength and stiffness to resist the forces and limit the displacement associated with movements in the rock mass surrounding the excavations. The CRF material preparation often involves the use of large particles, either from crushed rock or development mining waste. This means that conventional laboratory samples cannot be readily used to determine the laboratory strength. Consequently, a research project was undertaken to determine the influence of sample size on uniaxial compressive strength. This paper presents the results from CRF samples that were prepared using the same mix design and then cast into moulds with diameters of 150, 240, 300 and 400 mm. The laboratory testing also allowed a better understanding of the effect of particle size distribution upon the overall strength of a rock fill mass. The laboratory results were compared to a database of large-scale results from the testing of fill masses from a number of mine sites.CITATION:Cordova, M, Saw, H and Villaescusa, E, 2016. Laboratory testing of cemented rock fill for open stope support, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 755–762 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

A comparatively new and very promIsmg field for applying cemented tungsten-carbides is in the mining and quarrying industries. The economic advantages of this unique engineering material over the conventional hollow drill steel, or steel detachable bits, have proven so great that the use of "hard metals" promises, in some instances, to revolutionise the drilling of all manner of minerals. Early in the war years the Germans realised the tremendous advantages cemented carbides offered for holing hard rocks, and they proceeded to develop detachable percussion bits to do this work, at the same time evolving fast, comparatively light-hitting driliing machines, especially designed to suit the mechanical properties of the carbide.Here in Australia also, it has appeared that the detachable percussion bit offers the greatest economic benefits to consumers, although the author is well aware that carbide-tipped drill rods have, and may continue to work out satisfactorily in certain mines and quarries.Most drilling equipment at present installed in Australia may be described as being of the heavy hard-hitting variety, so that the designer of an efficient percussion bit has to take special precautions to overcome the problem of fatigue, and to ensure that the inserts are securely mounted in the body with the minimum of internal stress in the carbide.

Jan 1, 1950

By J, T C. McCuaig, J Hodgkison, T Fouet

Olympic Dam is the eighth largest Cu deposit and the largest U deposit in the world, with approximately 35 million tonnes of contained Cu and 1.2 million tonnes of U. The most recent resource estimate was for 2.95 billion tonnes of mineralised material with average grades of 1.2 per cent Cu, 0.4 kg/t U, 0.5 g/t Au, 2.6 g/t Ag as contained mineral resources. Olympic Dam is expected to produce >200 000 tonnes of Cu and 4200 tonnes of U3O8 from 9.8 million tonnes of ore in 2004, making it the 12th largest Cu producer in the world. One of the impediments to achieving targeted rates of production has been oversize material (>0.9 m) reporting to stope draw points. A major contributor to oversize material may be overbreak along pre-existing structural weaknesses from stope walls and backs during the production life of a stope. Underbreaking to structures can also have a detrimental effect on the performance of a stope. In an effort to understand the influence of structural geology on stope performance, WMC Resources and SRK Consulting partnered during 2003 to refine the current system of structural mapping, and to use historical data to produce a structural interpretation covering a large part of the mining area. The interpretation has been wireframed in DATAMINETM into a three-dimensional structural framework model. To date, there are more than 600 structures of >50 m strike length incorporated into the structural framework model, which covers a study area 1500 m + 600 m + 350 m. A back-analysis exercise to assess the influence of interpreted structures on overbreak and underbreak was completed for laser-surveyed stopes.

Jan 1, 2004

The main factors which influence disposal of mine waste under New Zealand conditions are identified and discussed: namely, geological conditions which produce soft weather-sensitive waste, wet and cold winters which affect productivity in such waste, elevated seismicity which affects stability and the need for water rights which involve public participation. The waste disposal scheme for the Martha Hill Project is described, thereby illustrating how these factors influence the planning of a current mine strippings and tailings disposal scheme.

Jan 1, 1986

By Pfeifer H. C, Nicacio P. A D

Sinter has been used as part of the metallic charge in large-scale blast furnaces for many years with the well-known benefits in terms of productivity and fuel consumption. However, because of the high investment in a conventional sinter plant, small blast furnaces and the associated integrated mini steel plants have not taken the advantages of using sinter. Recently KTS Korf Tecnologia Siderurgica, a division of Mannesmann Demag Ltda in Brazil, has developed a mini sinter plant for which the investment is compatible with small blast furnaces. Consequently, it is of great interest to evaluate the economical impact of using sinter in such small-scale integrated steel plants. In order to compare two alternatives, ie 100 per cent ore and 70 per cent sinter in the blast furnace burden, mass and heat balances for the entire operation from sinter plant through the blast furnace and EOF-based melting shop, were performed to evaluate the final production cost of the liquid steel. It was found that, depending on the sinter feed price, substantial savings can be obtained with the use of sinter.

Jan 1, 1999

The coalmining industry in most countries has, at various times, suddenly been confronted with a decrease in demand for coal. Readjustments made to reduce productive capacity to match the reduced demand for coal have often resulted in hardship to mineworkers, loss of capital investment to mineowners and loss of coal reserves. The consequences of the methods of readjustment adopted in the past have contributed to the low esteem in which coalmining has come to be regarded by a large section of the gel).eral public in many countries.Four sections of the coalmining industry, representing different periods of time, different countries, and different methods of industrial organisation have been examined:Great Britain and the U.S.A. during the inter war years, the post war European Coal and Steel Community, and post war Great Britain under the National Coal Board. An assessment has been made of the methods adopted in each case to reduce productive capacity to match a reduced demand for coal. Finally the fundamentals of the problem-as it affects the coalmining industry of any country-are considered, and possible solutions put forward.During the 1950's, surplus productive capacity was a problem in many coalmining countries, including Australia and New Zealand. As a rule no techniques are developed beforehand to solve problems introduced by a sudden decrease in demand for coal. The situation is usually tackled by a series of short term decisions based on expediency, which often in the long run only aggravate the problem.

Jan 1, 1961

Three main divisions of the Proterozoic are recognized in the North-West Division of Western Australia. These are referred to, in order of decreasing age, as the Mt. Bruce Supergroup, the Bresnahan Group, and theBangemall Group. The stratigraphy and distribution of each is described, their relative ages discussed, and a brief geological history of the whole area is presented.

Jan 1, 1966

n the early days of the Hauraki goldfield (1866 to 1889) almost the only system of ore treatment was wet crushing followed by copper plate amalgamation. A further saving of bullion was in most cases obtained from the tailings by means of pans or berdans. Though this system was not always as efficient as might have been desired it answered fairly well for the bulk of the gold-bearing quartz of the Thames and Coromandel districts, where the gold occurs chiefly in the form of visible particles, and there is not a great deal of silver. It failed, however, with most of the ore found in the Upper Thames or Ohinemuri district, especially in the Karangahake and Waihi portions of the field. In those days the cyanide process was not, and the usual prescription of the mining " expert" was smelting. At Karangahake, many attempts were made to discover a payable method of treatment for the so-called" refractory" ore, but on thewhole with very 'little success, and the district struggled along for a number of years without adding very materially to the production of gold in New Zealand. At Waihi, the Martha Co.'s stamp battery treated by wet crushing and copper plate amalgamation some 18,000 tons from the Martha Reef, worth probablyat least £4 per ton, but the average return was considerably less than £1 per ton, a sum which barely paid working, expenses, and consequently the shareholders were glad...

Jan 1, 1903

Geotechnical input is interwoven into the mining process at George Fisher South Mine from the planning and design of working areas to the closure of worked out areas and maintenance of life of mine and long term excavations. The methodology used consists of a mixture of application of established theoretical principles and guidelines derived from successful historical experience. In the development stage, including long term infrastructure excavations, the process takes into account the expected life of the excavation, usage and expected stress changes during its life span. On the stoping stage, the design process takes into account the local rock mass conditions, geological structure setting and previous experience in a particular orebody. Due to the high variation in age of currently used excavations, a rolling monitoring and risk assessment process for long term and life of mine excavations and infrastructure is maintained. This paper has as an output the process that must be followed to ensure an excavation on the highly dynamic mining environment at George Fisher South Mine is blasted and maintained in compliance with applicably commonly accepted safety and industry requirements.

Nov 25, 2010

This paper discusses the history and development of the system and the benefits that are being gained for Yabulu from Solar Drying. Following the end of mining of the local Greenvale and Brolga nickel deposits, QNI Yabulu Refinery is dependent upon imported ore from over 15 different mines in New Caledonia, Indonesia and the Philippines.

Jan 1, 2003

In the course of the last twenty eight years the copper lodes of New Caledonia have been periodically worked or abandoned, until quite recently, probably attracted by the higher price of the metal, British capital has again been induced to embark upon the further development of several copper properties, which at present give reasonable promise of becoming regular producers. Owing to its proximity to Australia (only a three day's journey by mail steamer from Sydney) New Caledonia becomes of additional interest to Australian commerce in general, and it is to be hoped that the French Government may see their way before long to make the best of this natural position, to the mutual benefit of both countries concerned.Op till now all copper ores and concentrates which have been shipped from New Caledonia, were treated in Australian smelting works furthermore, Australian mine managers and miners have from time to time been connected with New Caledonian mining ventures, but, unfortunately, it must be said that nearly everyone of them returned to Australia thoroughly disgusted with his experience over there. Even to the casual observer, it is not so very difficult to find a proper explanation for these shortcomings in the peculiar economic conditions of the 'French colony, as many of the objections which have hitherto existed in connection with mining operations, were the direct consequences of a system of colonisation which could not possibly have been productive of better results.

Jan 1, 1901

By Penrose E. K

With the exception of occasional periods, when up to 80% of oxidized ore was treated, the G.M.K. plant treated all sulphide ore until October, 1939. The treatment was, briefly, as follows:The ore was ground to approximately 17% plus 200 mesh Tyler and agitated in cyanide solution, after straking. After agitation, the pulp passed through two stages of counter-current decantation washing in Dorr thickeners and was filtered once, to complete the precyanidation stage.The precyanide filter cake was repulped with flotation circuit solution and floated in a Denver Sub A flotation machine, consisting of twelve cells. The concentrates were roasted, cyanided and filtered four times before disposal to the' dam. The flotation tailings were thickened to conserve water and pumped away to a separate dam.The average results of flotation operations for the six months before October, 1939, are shown in Table 1.

Jan 1, 1942

The case study has identified and characterised additional subsidence arising from longwall mining above or under existing longwall goaf. It suggests that the magnitude, mechanisms and prediction methods for such additional subsidence are different between the two mining configurations. This paper presents a proposed method to predict maximum vertical subsidence due to longwall mining under existing longwall goaf. It suggests that, unless different results from further new cases become available, the findings presented in this article, including the aforementioned prediction method, be applicable to the majority of sites in New South Wales, where multi-seam longwall mining is to take place. This article also presents an important concept of 'overburden modification' due to multi-seam mining. A causal relationship between the above-mentioned additional subsidence and 'overburden modification' has been identified as a result of the case studies. Further investigations into the physical processes that cause such overburden modification will be fundamental to the understanding and management of multi-seam subsidence.

Nov 25, 2010

IN the recent monograph on Broken Hill, N.S.W., by E. C. Andrews,* two independent petrological reports appear as Appendices 1 and n, by W. R. Browne and F. L. Stillwell respectively. In these considerable differences of opinion occur. Andrews contributes to some of the questions at issue, but no analytical review of the differences appears in the body of the report. Their development may invite question, and the following notes have been prepared partly in explanation and partly as a summary of some of the divergences. The soope of Browne's report extends over the whole district of Broken Hill, while Stillwell's deals with the rocks within 25 chains of the main lode. The more difficult and important rock-types occur in both areas, raising similar questions. In both cases observations extended beyond the limits of the prescribed areas. Broadly, Browne faces his problem as a study of a series of primary igneous rooks, acid and basio, whioh are intrusive into a series of sillimanite gneisses. The development of the sillimanite gneisses is regarded as belonging to an earlier period than the intrusion of the igneous rooks, while the gneissio structures of the latter are features which are incidental to their orystallization, and are not acquired subsequent to their consolidation. He finally produoes a picture in which his views of igneous injection and differentiation takes a prominent place. One direct result is the claim that three separate periods of metamorphism have oocurred in the Broken Hill area. Stillwell primarily examines the rooks as schists and gneisses since their present dominating features have been acquired during metamorphism. The effort is made to understand suoh differences as might arise from differing conditions of metamorphism upon rocks of similar and different oonstitution. The aim is to divest the rocks of those oharaoters which are due to metamorphism before approaching the questions of intrusive relatio'nships between igneous rocks andsediments.

Jan 1, 1924

By Fogarty J. G H

Ausmelt Technology has a unique capability of removing the impurities, phosphorus and sulphur, from the feed materials to the process. Sulphur is removed to the gas phase almost completely because of the interactions of ore and coal in the reaction region at the top surface of the slag bath. Phosphorus is removed to the slag phase, with both basic and higher, controlled iron oxide levels in slag being achieved in the process. The significance of these features of the process relate to the production of pig iron with very low levels of these impurities for the further processing to steel, and to the treatment of high phosphorus and high sulphur raw materials. The marketability of pig iron and the raw materials are discussed in relation to this feature of Auslron.

Jan 1, 1999

By Davies S. G, Mackey L. C

The oxidation of iron and nickel sulphide concentrates, and the dominant sulphide minerals which comprise them, has been studied under ignition conditions using thermogravimetry (fG). The concentrates were derived from various minesites and they showed differing tendencies to ignite. Ignition temperatures ranged from 416 to 488°C and the extents of reaction, measured at 500°C, varied from 64 to 88 percent. The reactivity of the least reactivematerial was improved significantly by grinding. Particles <63/lm showed 85 percent oxidation compared with 55 - 65 percent for particles >63/lm.Examination of the individual sulphide minerals revealed that these materials also have significantly different degrees ofreactivity and are subject to particle size effects. For particles <45/lm, the ignition temperatures were as follows:ò pyrite and violarite 380 - 385°C; pentlandite 425 - 430°C; and pyrrhotite 470 - 475°;ò for particles >90 /lm, the ignition values were: pyrite 395 - 400°C;ò violarite 430 - 435°C; pyrrhotite 540 - 545°C; and pentlandite 560 - 565°C.Using the data on the individual minerals it was possible to rationalise the differing degrees of reactivity of the concentrates. The role of the most reactive constituent in initiating the ignition reaction has also been discussed.Finally, the results of this work were found to compare. favourably with the behaviour ofthe concentrates in industrial and pilot-scale flash smelters.

Jan 1, 1989

Iron Ore - Mineral Processing Overview Several years of iron ore price increases, coupled with a period of strong global demand for raw materials, presented iron and steel producers with unprecedented costs and difficulty procuring the demanded high quantities of iron ore. These conditions spurred many companies to investigate new ore bodies and also reassess past decisions (such as divestment of captive iron ore mines that ensured dedicated supply or a move to reliance on the 'spot market' instead of long term contracts with suppliers) and revisit alternative sources of iron units, including low grade deposits, tailings reprocessing, Ti-rich ores, and iron sands. To properly upgrade these iron sources requires a complete battery of mineral processing techniques. Within different regions around the world, operations and technology have developed to specifically beneficiate the local ore bodies. This paper attempts to bring these different general processing techniques together to allow insight into various common and proven methods of iron ore beneficiation. This paper further explores the current trend to develop global iron ore reserves, and discusses the methods to beneficiate and successfully reduce and smelt iron ore using Outotec's physical separation, direct reduction and smelting technologies for final production of pig iron and slag. Use of these various technologies may allow treatment of what was typically considered a tailings stream into a profitable product.

Sep 13, 2010