Search Documents

By Wright D. J

Successful heap leaching depends on three major factors: 1. Chemical conditions appropriate for the dissolution of the valuable metal; 2. Contact between the leach solution and the valuable metal particles; and 3. Movement of the leach solution through, and out of, the heap. Given that appropriate chemical conditions can be provided, and the individual particles have sufficient permeability to allow solute/solvent contact, the problem of getting the solution to and from the particles remains. Non-uniform percolation of solution throughout the heap, caused by the presence of fines, is a common problem which occurs, to some extent, with all heap leachable ore. The conventional solution to this problem is agglomeration, which involves the attachment of fine particles to larger particles, effectively modifying the size distribution by preventing the fine particles from acting on their own. While agglomeration must be considered as an extremely effective technique with virtually no limit to its application from a technical point of view, its application is limited by economic considerations. A new technique has been developed which is not only a low cost alternative to agglomeration, but also has the potential for enabling the application of low cost heap and vat leach techniques to a significantly wider range of ores than current practice would suggest. The new technique, known as Electrokinetic Leaching, utilises electro-osmotic flow to enhance percolation through the heap. This paper describes and presents results of the laboratory testing, pilot heap operation and commercial application of Electrokinetic Leaching of a low grade gold ore and a tailings deposit. Comparative cost analyses between conventional and the alternative processing techniques are presented.

Jan 1, 1994

The results expected from a longwall face can best be estimated from the ideal production rate, determined by the capacity of the equipment and the conditions in which it is installed, the effective operating hours, and the utilisation.The effective operating hours are determined by a number of scheduling factors which include the proportion of manned time to calendar time, the effective shift factor (effective time to manned time) and the move times.Analysis of the results achieved on the last 121 completed longwall panels in Australia (1984 onwards) shows a significant trend between 'actual tonnes/manned hour' and 'ideal production rate' (the measure of the capacity of the installation).Using 1982 'state of the art' longwall equipment, (the average in use in the seven year period), it should be possible to produce around 2.7M tonne/year ROM from a mine with one longwall. Few mines are achieving this.A review of production scheduling factors and general natural hazards affecting some mines suggests three things.1. Whilst some increase in average effective hours has followed the CIT decision, further improvement is possible at many installations.2. Many mines subject to general natural hazards, such as high gas make and high general stress, have found effective solutions and achieve the same utilisation as the overall average.3. A small number of faces within such mines have been severely affected, some less so. The most severe effects of natural hazards appear to be very site specific. This emphasises the need for detailed investigation of the causes, and development of means of predicting their presence. Only then can either satisfactory technical solutions be found to overcome the problems or prior decisions be chosen not to mine badly affected panels.

Jan 1, 1991

By D Curry, M F. Young

æConventional wisdomÆ believes that fine particles have low flotation recoveries. Plant size û recovery graphs often have the classic æhillÆ shape û high recovery in the mid sizes and low recovery at the fine and coarse ends. Yet if mineral liberation is poor, low fines recovery may be because you don't grind fine enough! This apparent paradox is explained by the old concept of æsand/slimesÆ circuits, which recognises the different flotation needs of fine and coarse particles. This concept is overlooked in the push for simpler circuits and larger equipment. Most plants now treat all particles together in a wide size-distribution. Reagent conditions are set for the dominant coarser particles, so fines are starved of collector. Worse still if there are significant midsized composites û often these have to be rejected in cleaning to achieve target concentrate grade. But the conditions which reject mid-size composites û collector starvation and high depressants û also reject fine liberated particles. In fact, fines flotation can be excellent when flotation chemistry is tailored to fines.

Jan 1, 2004

The project is undertaken by Elgas Pty Ltd, a 50 per cent joint venture between AGL and BOC, to store 65 000 t of LPG in underground storage at Port Botany, NSW. The contractor, Concrete Constructions Pty Ltd, elected to use drilling and blasting techniques. The project specification called for the following works to be excavated: Access Shaft:122 m (out of 140 m total depth), 6.0 m diameter (selected by the contractor),Operation Shaft:125 m (out of 150 m total depth), 4.0 m diameter,Water Curtain Gallery:500 m (Later extended by additional 270 m), 4.0 m wide and 3.5 m high,Storage Caverns:910 m, 14.0 m wide, 11.0 m high,Top Heading:14.0 m wide, 5.5 m high,Bench:14.0 m wide, 5.5 m high,Connection Galleries:250 m, 5.5 m wide, 5.5 m high.A total of 156 000 cubm of rock to be excavated.

Jan 1, 1999

By S Roberston, G Batt, R Shanahan, B Shah, A Trench, H Bromfield

The geographic imperative of ore systems leaves mining, more so than virtually any other aspect of modern industry, heavily dependent on obtaining and maintaining social licence to operate. A prospective miner cannot arbitrarily walk away from a deposit in search of more favourable community perceptions – concentrations of mineral endowment represent highly specific and fixed elements of the landscape, and their development and extraction thus requires the acceptance and trust of a specific network of landholders and stakeholders, sometimes with diverse and even competing interests in the development and use of the local environment. Weakness or absence of such social licence can bring added costs and complexity to developing and operating a mine – and in extreme cases even result in project failure. Because it must be maintained throughout the life of a project, such social risk becomes a substantial part of overall project risk profile, particularly during routine operations once initial technical and development risks have been largely resolved.CITATION: Bromfield, H, Roberston, S, Shah, B, Shanahan, R, Trench, A and Batt, G, 2018. On equitable distribution of mining wealth and the social licence to operate imperative – an African case study, in Proceedings Complex Orebodies Conference 2018, pp 6–7 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

This case study reviews the Charters Towers vein systems for potential open-pittable bulk tonnage resources in' stockworks, horsetails or multiple vein systems. The review summarises district evaluation undertaken over the last 18. months before specific drill evaluations.Historical mining from Charters Towers includes in excess of six million ounces at head grades of one ounce per ton. A review and structural studies show most veins as simple, tight systems without significant horsetails or multiple sheeted systems. In addition the normal gold content of the pyritic selvages ('formation') is low and disseminated gold is virtually absent. Shoots are structurally controlled on vein/vein and vein/contact intersections. Historically high production vein systems are hosted by .,.t o of the younger granodiorite phases.Geometrically most veins dip shallowly (from 45¦ to as low as 200) in a north or easterly quadrant. Flat dips permit open cut exposure of considerable vein area at a favourable stripping ratio.

Jan 1, 1986

It is proposed to deal with those raw materials which are produced in South Australia to meet the needs of the country's steel industry. They are chiefly, iron ore, limestone and quartz.Iron ore and limestone are fed to the blast furnaces of Newcastle and Port Kembla together with coke to produce the hot metal charge for the open hearth steel furnaces.They are also qsed in the raw state in the steel furnaces to assist in the conversion of the hot metal to steel. The iron ore is quarried from' Iron Knob and shipped from Whyalla to Newcastle and Port Kembla, whilst the limestone is supplied from the deposits at Rapid Bay and shipped in the same manner.Quartz is used in the manufacture of ferro-silicon, an alloy which is added to the ladles of molten metal tapped from the open hearth furnace in the case of almost every grade of steel. It is obtained from a quarry situated between Iron Knob and Whyalla, and shipped to Newcastle.IRON OREWith the exception of several small quarries situated at Breadalbane, Cadia, Cowra, Crookwell, Michelago, Jerrawa and lerraama in New South Wales, the iron ore requirements of Australia's steel industry to date have been met from Iron Knob and the Middleback Range in South Australia.Several of the small deposits in New South Wales were worked during the war years of 1941-44 during the shipping emergency and produced 1,355,417 tons, compared with an output of approximately 43,000,000 tons from Iron Knob between 1901 and 1949.

Jan 1, 1951

By Reeve JS

Heap leaching is a low capital cost alternative to conventional processing techniques for gold recovery from areas that contain small gold particles in a porous host rock.For successful heap leaching the ores to be leached must maintain good permeability after being stacked into heaps so that the leach solutions can percolate evenly through them.The presence of clays, slimes or excessive amounts of fines can hamper the flow of leach solutions causing channelling and producing dormant or unleached areas within the heaps. This results in unreasonably long leach periods and poor extractions. In extreme cases the clays or fines completely seal ore heaps, causing leach solutions to run off the sides of t'he heaps rather than penetrate the ore.The Northern Queensland Company uses the Agglomeration Heap Leach technique (AHL) to overcome the difficulties associated with clays or fines. This technique involves cementing the fines, by using readily available binders, into a rigid, porous network that greatly enhances uniform flow of cyanide leach solutions through the ore heaps.

Jan 1, 1986

The Kidston Gold Mine i s located in northern Queensland some 2 Ukm northwest of Townsville. I t is the largest gold mine in Australia and produces approximately 25 percent of Australia's gold and one percent of the world's gold.Initially, traditional mining industry management approaches resulted in the rejection of what appeared to be an attractive low-grade deposit as an uneconomic proposition. Critical re-examination revealed that the rejection was based upon managerial inflexibility and traditionally over-conservative methods of mine evaluation, construction, operation, projected commodity prices and contingency factors. "Ihus it tradition was to prevail, the Kidston prospect would never have been realised.

Jan 1, 1985

Among the various methods of thick-seam mining already well-tried in practice longwall caving with extraction of a single slice, as thick as possible, abandoning the top and/or the bottom coal, seems to be the most suitable one for the Australian coal mining industry. The production units of the future should be equipped with heavy double-drum shearer-loaders, wide armoured conveyors, (with one or two central chains) and shield support. Material of this type has been developed for seams up to 6 m thick. Output figures of more than 6,000 tROM/d from a single face can be looked upon as a quite realistic expectation. The problems of co-ordinating such large production units with the whole layout of the mine are discussed. The factors to be taken into account in the planning work and for preven- tion of mine fires caused by spon- taneous combustion are dealt with. For economic reasons the highest possible utilization factor of the very expensive equipment must be aimed at. Furthermore, the seams or parts of seams to be extracted should be carefully selected.

Jan 1, 1976

By J N. Farrell

Metallurgists frequently use a small number of large samples to characterise expected mill performance, with the a priori assumption that these few samples are representative of the entire deposit. Geometallurgical sampling is becoming more prevalent as a way to use many smaller samples to indicate the expected recovery as part of the Mineral Resource or Ore Reserve estimation.The evaluation of magnetite deposits involves specialised approaches to sample preparation, sample analysis and resource estimation. The sampling protocol for magnetite deposits will typically include the use of Davis Tube analysis. The Davis Tube is a mini-pilot plant that is used for determining the mass magnetic recovery from a small amount of sample ground to a specific size. The magnetic concentrate may then be analysed and together with the mass magnetic recovery, may be used to simulate the expected mill recovery. The magnetite sampling protocol is specific to each deposit, and is typically designed around a specific metallurgical flow sheet.During resource modelling, the mass magnetic recoveries and concentrate grades may be estimated directly or assigned to a block model using regressions with other chemical constituents. For estimation, the concentrate grades are weighted to account for the different mass magnetic recoveries of each sample and the impact of these differences on the concentrate estimates.

Sep 5, 2011

By Rajan S, Mainwaring P, Gould WD, Beaulne M

Polished discs of a complex sulphide ore were leached with three lixiviants; a mixed culture of Thiobacillus ferrooxidans and Thiobacillus thiooxidans, Thiobacillus ferrooxidanalone, and ferric sulphate. At either one or two week intervals the discs were examined by scanning electron microscopy, and the amount of soluble metals released from the discs were determined. The mixed culture solubilized more Cu, Zn and Pb than did either ferric sulphate or T. ferrooxidans alone. However, no differ-ences were observed between the three treat-ments by scanning electron microscopy during the first 44 weeks. The minerals were attacked in the following order: pyrrhotite, cubanite, sphalerite, pyrite and chalcopyrite.

Jan 1, 1990

UNLIKE coal mines, in which some form of artificial ventilation is rendered necessary by gases given off by the material mined and is also enforced by the mining laws of all countries, metalliferous mines have almost entirely relied on natural ventilation, viz., that due to the difference in temperature between the outside atmosphere and the mine air. In small mines natural ventilation has proved sufficient, but as mining proceeds at a greater depth, and where large ore bodies arebeing attacked the writer is of opinion that some means of artificial ventilation will be rendered necessary if only from an economic standpoint.The Broken Hill Proprietary Mine was one of the first metal mines to introduce a scheme of artificial ventilation on a large scale. In order to render the working conditions of the semi-friable stopes of Block 12 and the lower levels of Block 11 morecomfortable for the men at work in these places, in 1903 it was decided to install a fan to thoroughly ventilate these stopes. The fan chosen was a Capell double-inlet fan beltdriven from a steam engine: this engine was later on replacedby an electric motor. The fan was put in commission at the latter end of 1904; its principal dimensions are as follows: Length 6 ft. 6 in., diam. 7 ft., diam. of inlet 4 ft. 7i in. The fan is reversible, though this is a rather misleading term, asthe direction in which the fan blades revolve is not reversed...

Jan 1, 1921

The general types of industrial behaviour of liberated valuable sulfide minerals in the 0 - 10 ¦m size fraction are described and tests to explore on site at a concentrator the general nature of any deficient behaviour are discussed. In addition, the general types of behaviour of the gangue minerals in this size fraction are also described in terms of their mechanisms for recovery. These behaviours are also discussed in terms of the type of grinding device and grinding environment in which they were produced and the target grinding product size. Major recent improvements in the industrial capabilities of grinding devices are discussed.Present difficulties in characterisation of particles in the 0 - 10 ¦m range are described and desirable improvements for the future are outlined. Further, desirable improvements for industrial processing of valuable minerals in this size range are discussed along with some remedial actions.

Jan 1, 2005

This paper examines the complex interplay of deposit characteristics, mining plans, tailings disposal techniques and rehabilitation requirements on planning for mineral sands operations. All component parts of this mining cycle are interdependent and cannot be evaluated in isolation when optimising a mineral sands operation. This is most evident when projects are large-scale or involve resources that contain complexities such as high slimes content, consolidated hard band materials, acid forming materials and radioactive materials. Projects located in environmentally sensitive areas add further to the need for more stringent planning. This paper describes the analysis techniques adopted by Hatch to evaluate mining and tailings placement options for a dredging and floating concentrator system. The principles and methods used in the analysis are applicable to any mining system involving the complexities listed above. The focus of this paper is on the reconstitution of mined material as tailings and the impact of this process on mining schedules and tailings construction and placement options.

Jan 1, 2001

By D Cliff

"Recent underground coal mine incidents have again raised the issue of: under what circumstanceis it safe for personnel to re-enter the mine? Mine rescue guidelines make recommendations aboutthe limits in terms of the circumstances, lives at risk, no lives at risk and training exercises. Theseare based upon percentages of the upper and lower explosive limits. Many factors infl uencesett ing limits for safe re-entry. These include: the representativeness of the sampling location(s),the rapidity of gett ing an underground sample analysed and the rate of change of the atmospherebeing monitored. Value judgements based upon these parameters will then infl uence the sett ing ofa trigger point based upon per cent explosibility. This raises the question of how the percentage ofthe lower or upper explosive limit is established. It is easy to defi ne this when the sampling pointdata sit on the fresh air limit line. However - what value is used when the sample sits somewherein the body of an explosibility diagram? This paper explores the various options and illustratesvarious pitfalls and problems that are faced in making such a determination. These include howthe data are represented and the assumed knowledge of those doing the interpretation."

Jun 1, 2012

By R Klepper

Separation of leach residue suspended solids from pregnant liquor solution is an important step in hydrometallurgy flowsheets. Alternative flowsheet options are counter-current decantation (CCD) thickeners or counter current washing (CCW) horizontal belt vacuum filters. Extensive sedimentation and vacuum filtration simulations have been completed by FLSmidth on leach discharge slurries to indentify equipment capacity and performance. These data were used to compare Capex and Opex for CCD versus CCW alternatives. In addition, Capex and Opex for large horizontal belt vacuum filters with filtration areas greater than 250m2 are compared to current state of the art sizes of 150m2. This paper presents this information and discusses various advantages and disadvantages.

Aug 8, 2011

By G Chitumbura

Raise boring is a critical aspect of mining at Xstrata Copper’s Mount Isa Copper Operations (MICO). MICO’s internal raise boring department regularly develops ventilation rises, orepasses and stope cut-off rises and reams approximately 2500 m per annum. Developed, trialled and implemented as standard practice over the past two years, procedural changes in constructing the raise bore machine’s foundations have significantly reduced operator exposure to raise boring’s inherent risks of working around open holes and manual handling. An additional cost benefit of this newly-adopted procedure is derived from reducing the likelihood of damaging the machine while de-rigging.When conforming to standard industry raise boring practices, exposure to an open hole begins when the reamer breaks through the concrete pad and ends when it is removed from the hole – a process which, depending on the size of the hole and the raise boring machine, can take up to three days to complete. Although wearing fall restraint equipment, operators working on and around the raise bore machine during de-rigging are continually exposed to the risk of falling from heights. In contrast, MICO’s newly-developed and successfully-implemented presink raise boring system reduces this exposure to a maximum of four hours, regardless of hole size. Exposure to manual handling hazards is also substantially reduced as the presink procedure eliminates manual placement of a 100 kg drill bit under the machine to commence pilot-hole drilling. Outcomes of implementing the presink System at MICO have been so beneficial that it is now standard procedure for all reaming in excess of 1 m diameters.

Mar 21, 2011

By Dip L. B

This paper describes the new legislative regime that will apply to the regulation of the minerals industry in New Zealand.The reform of New Zealand's minerals legislation was initiated in January 1988 when the Minister for the Environment, Rt Hon Geoffrey Palmer, announced the Government's intention to review all the major laws governing New Zealand's resources. The Resource Management Bill is scheduled for introduction to the House in December 1989 and its date of enactment is scheduled for June 1990.

Jan 1, 1990

By H Catchpole, L FontbotT, J PTrez, M Ageneau, A Bendez·

In the world-class mining district of Morococha, epithermal polymetallic replacement bodies and veins overprint porphyry mineralisation and skarns related to subvolcanic intrusions of Miocene age, thus indicating ore formation in two different environments, separated in time or forming a continuum. The district covers an area of about 70 km2 in the north-western part of the Domo de Yauli complex in theWestern Cordillera of central Peru and is part of the Miocene polymetallic belt, also hosting the deposits of Colquijirca (Bendez· et al, 2008b) and Cerro de Pasco (Baumgartner, FontbotT and Vennemann, 2008). Multiple late-Miocene porphyry stocks intruded Permian, Triassic-Jurassic and late-Cretaceous sedimentary carbonate and volcano-sedimentary formations, as well as large mid-Miocene barren intrusions. Extensive field work and detailedmapping of different styles of orebodies suggest that ore formation in the area was related to the late-Miocene magmatism. Good outcrop conditions and superimposing of different mineralisation styles make Morococha an ideal location for studying ore-forming processes in a complex porphyry-related magmatic-hydrothermal system in which porphyry-to-epithermal transition occurred. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008