Search Documents

By P Nichols, C te Kloot, A Harrison

Ernest Henry mine (EHM) is a sub-level caving operation located in north-west Queensland, Australia. Located below a previously mined open pit, the underground operation ramped up production to 6.8Mt/a in 2017. The EHM ore body dips at 45 degrees to the South and therefore requires each level to “step out” from the level above as seen in Figure 1. Within this step out zone it is important to both maximise recovery and allow for efficient operation of the underground workings production to bring the level up to full production as quickly as possible. Throughout the step out design process, a combination of further defining the ore boundary, using lessons learnt from production performance on upper levels and the introduction of design improvements, has reduced the production ramp-up time, decreased costs and increased recovery for a single level at EHM. CITATION: Nichols, P, te Kloot, C and Harrison, A, 2018. Case study – Ernest Henry Mine: designing step out zones in an inclined sub-level cave, in Proceedings Complex Orebodies Conference 2018, pp 53–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By K Lee, L Mann, J Bygrave, G Sheldon

Ausmelt is supplying commercial quantities of an alkyl hydroxamate flotation collector AM28 for flotation of oxide and supergene base metal ores and tailings. AM28 is a non-hazardous product used as a ten per cent to 50 per cent solution in dilute potassium hydroxide. It is a selective flotation collector for oxide or oxidised base metal minerals and replaces conventional sulfidisation for oxide mineral flotation. At Radio Hill, the AM28 is used in conjunction with traditional sulfide collectors, which allows simultaneous flotation of oxide and sulfide copper minerals. The Fox Resources Radio Hill copper concentrator near Karratha, Western Australia, is currently configured to treat supergene copper ore sourced from the West Whundo open pit. This Archean VMS type copper deposit has been deformed and remobilised with uplift, erosion and weathering to form a significant supergene zone. The sulfide copper minerals present in the upper zone are digenite and chalcocite with lesser chalcopyrite and covellite. Oxide copper minerals present include cuprite, with lesser malachite and azurite. Gangue minerals include quartz, talc and chlorite. Plant trials at Radio Hill are reported for supergene West Whundo ore, where the AM28 was stage added into the circuit at nominally 80 g/t. Plant data over three months shows the copper recovery increased consistently from around 50 - 60 per cent to above 70 per cent when AM28 was added. This has been proven statistically. The grade of the concentrate was consistent with and without AM28, at nominally 22 - 24 per cent copper.

Jan 1, 2007

By Y Durkheim, P Saunier, L Ameglio

"In the last decade Afitex developed the Draintube™ geocomposite, which provides simultaneous drainage and waterproofing functions. This new type of drain tubes planar geocomposites (DTPG) differs from other geocomposites as the drainage core is composed of multiple corrugated and perforated pipes instead of biaxial or triaxial nets. It is furthermore associated with needle-punch stitched layers of non-woven geotextiles, which act either as capillary mediums or as filters.In this paper, the structure of the Draintube™ drainage composite is presented along with its key properties and the drainage mechanism associated with its particular structure.The relevance of this kind of structure is then reviewed based on past and current laboratory bench evaluations and field installations for mining applications such as the covering of acid rock drainage (ARD) tailings for the Central Manitoba Mine (Canada) site-rehabilitation; and as a pregnant solution collection layer in heap leach pads.Some of the demonstrated critical advantages of Draintube™ in the mining industry are as follows: reduction of the thickness, hence lower volume of granular drain layers improvement of fluid and gas collection and reduction of the hydraulic load reduction of secondary collector network mechanical protection of the sealing membrane fast and economical installation of interlifts stability under extreme conditions (compression, temperature, pH) increased stability of entire covering system and reinforcement of protection of dykes filtration of the covered material customised drainage positive connection of the geocomposite to collector pipes enable leaks detection (using a conductive textile layer) with an electrical test.CITATION:Saunier, P, Ameglio, L and Durkheim, Y, 2015. Tubular drainage and lining geocomposite for mine tailings and heap leach pads, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 297–304 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

By M Singh, R C. Steinhaus, J J. Rust

Metallurgical process control systems in mineral plants often employ state-of-the-art monitoring analysers in an attempt to optimise plant operations and enhance mineral recoveries. These systems are unfortunately invariably fed by simplistic ‘sampling’ designs consisting of various in-stream methods or pressurised probes. These are unfortunate compromises and provide a false picture of what a mineral flotation or other process can achieve. The situation is further aggravated by some manufacturers using misleading marketing to suggest discrete cross-stream methods for metallurgical accounting and unreliable continuous in-stream off-takes for control sampling and that they are of synonymous integrity.Reliable, absolute or representative samples are often absent in many modern day concentrator plants, due to compromises around sample taking, particularly in terms of delineation and extraction errors and thus leading to sample bias. For more reliable information from online analysers we need a continuous, but much more reliable sample taken, than is current practice.Online analysers require a fully proportional and continuous supply of sample for effective process control, otherwise maximised or benchmark recoveries will be nothing but a pipe dream. Large discrete cross-stream samples from mechanically less reliable equipment cannot be used as feed to online analysers, as it will negatively impact real-time feedback and efficient process control.It is possible to build correct sampling systems that could do both process controls online and metallurgical accounting at the same time. Multotec Process Equipment (Pty) Limited, in close association with experienced sampling consultant Francis Pitard, have jointly patented a concept to achieve this and which is embodied in the design of the unique Rotating Cone® Sampler (International Patent Application No. PCT/IB2016/057464). This versatile unit for dry and wet applications has high division ratios via two-step sampling and division.A prototype was built and tested to validate the design and levels of precision achievable when employing the unit to split dry mineral fines or even certain foodstuffs.CITATION:Steinhaus, R C, Rust, J J and Singh, M, 2017. Does process control sampling always have to be a compromise?, in Proceedings Eighth World Conference on Sampling and Blending , pp 197–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By D Reid

The engineering properties of soils and tailings often exhibit significant anisotropy. One area where this has been well documents is undrained shear strength. Materials sheared in directions close to the principal stress direction in situ, i.e. triaxial compression, typically exhibit higher undrained strengths than those sheared in other directions such as simple shear. Importantly, along the most common critical failure surfaces relevant to tailings stability, whether primarily through tailings or a critical foundation layer, saturated materials are generally much closer to the simple shear loading direction than triaxial compression. Therefore, testing undrained shear strength of tailings or foundation soils in triaxial compression is likely to result in overestimation of the relevant strengths for design. Although these issues have repeatedly documented in the geotechnical literature for over three decades, they are not appreciated sufficiently across our industry. In an attempt to address and highlight these issues, a review is carried out of historical reference to the importance of simple shear loading. Attention is then drawn to the techniques applied in three recent post-failure investigations, where simple shear testing was applied. Finally, some relevant laboratory test results from a recent project in which the author was involved are outlined.CITATION:Reid, D, 2018. Importance of the simple shear loading direction to the stability of tailings storage facilities, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 274–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

The grinding of ore to a size that is conducive to the extraction of minerals by leaching or flotation is an essential and expensive component of most mineral-processing operations. Overgrinding results in reduced flotability of the minerals, as well as problems in the filtration and thickening processes, while undergrinding leads to a product in which the minerals have not been exposed, and cannot be leached or floated effectively. Furthermore, coarse material causes settling in thickeners and agitator tanks. It is therefore essential, from the perspective of both operational and extraction efficiency, to grind the ore to an optimum size fraction. A well-run milling circuit will yield a product within a narrow size band and at a high throughput. Although the effective operation and control of milling circuits with their many operating parameters is widely acknowledged as a complex as well as a critically important operation, the benefits of such control are difficult to quantify. This is due to the difficulties in relating more stable operation to increased recovery of the valuable components in downstream processes.

Jan 1, 1993

By E C. F Hamman

Sunrise Dam Gold Mine is a large open pit mine 730 km NE of Perth, Western Australia. Contract mining commenced in the open pit in September 1996 in lake clays and saprolites with the first fresh rock mined late 1999, and the underground starting the first decline in October 2003. By May 2007, over 150 million cubic metres of material had been mined and the pit was 360 m deep with 80 m remaining before reaching the planned final depth in early 2008. A final cut-back in the northwest will commence in late 2007 with open pit mining in the Mega Pit expected to conclude in late 2010. The challenges of developing the pit can be divided into three phases:Soft materials û mining was in multiple staged pits and cut-backs in lake clays, saprolites, weathered material. The varying characteristics had a significant impact on mining methods and slope stability. Structural û mining was gradually exposing more fresh rock and the drive was to understand how major structures and lithological contacts impact on local and large-scale stability. This had a significant influence on mine design and scheduling. Slope angles û achieving the final slope angle is critical. This is done through application of high standards of final wall establishment and proactive geotechnical hazard identification and management. This includes dealing with the rapid rate of descent, interaction with underground excavations and managing rock fall risk. The paper discusses each of these phases, highlighting the geotechnical controls implemented to date, looking at their success and impact on mining.

Jan 1, 2007

By D Will

RedrossThe Redross orebody averages 1 m wide, has a strike of 50 - 350 m, dips at 55° and has a basalt footwall and an ultramafic hanging wall. The most successful and innovative aspects of mining Redross were:•ore development innovations, 90 per cent of development was split fired with a shanty back profile to enable larger and more productive equipment to be used and resulted in higher development grades, improved project payback time and improved ore recovery;•hand held stoping using a multiple level, bottom up ‘V’ shaped hand held stoping method that allowed mining on multiple levels with hand held productivities between 50 and 90 tonnes per shift;•the use of 1 m cement pillars and 7 m high crown pillars were used to create multiple mining areas that enabled high overall production rates from hand held mining this orebody; and•the use of vertical cement pillars to enable hand held mining of adjacent stopes without leaving ore pillars.MarinersThe Mariners orebody averages 3 m wide, has a strike length of 50 - 250 m and dips at 50° with a basalt footwall and poor ultramafic hanging wall. The most successful innovative ideas of re-opening Mariners were:•Dewatering the existing mine workings utilising ‘oilfield’ technology by installing a long submersible pump in on existing pump rising main. This enabled the mine to be dewatered at rates up to 100l/ sec and helped overcome the 45 to 55 L/s inflows.•Overcoming the technical problems associated with Mining N07 ore blocks which had severely deteriorated from being underwater for five years by using reverse firing techniques to improve extraction rates and reduce dilution.•Mass firing a large mining block in the N08 with minimal void space because of deteriorating ground conditions.•Use of a longhole version of the Redross hand held mining method to achieve 100 per cent extraction of the N09 higher grade lenses.

Mar 21, 2011

By M M. Collisson

The Synthetic Rutile (SR) plant operations, North Capel, produce electrostatic precipitator (ESP) fume and kiln scrubber residue. Typically ESP contains about 18 per cent Ti, 13 per cent Fe, 0.5 per cent Mn, eight per cent Si, six per cent Al, 16 per cent C, 0.9 per cent Zn, 0.6 per cent Pb, 300 ppm As, 300 ppm Cr and 5 ppm Cd. These wastes are held in a storage dam together with neutralised acid effluent (AE) liquor. A project was initiated to treat the fume and produce a benign residue that could be delivered to landfill, reducing dam space storage. Plant AE, containing free acid (9 - 14 g/L), Fe (6 - 7 g/L) and Mn (1 g/L), was used to leach ESP. The degree of extraction achieved for various elements include about 20 per cent Zn, almost 50 per cent As, five per cent Al, 0.4 per cent Pb and 15 per cent Cd. Extraction was most effective at pH The residue from AE leaching still contained Pb. TCLP tests of the leach residue produced Pb extraction significantly higher than the 0.1 ppm stipulated by Class 2 landfill guidelines. Other elements (eg As, Cd, Cr) successfully met the limits. Further leaching of the residue with EDTA extracted up to 65 per cent of Pb content. TCLP tests on treated residue showed Pb leaching potential of Lead was removed from the leach circuit as the sulphate by acidification of EDTA leach liquor, allowing EDTA to be recycled. The study showed that one waste stream can be used to treat another and help reduce plant waste.

Jan 1, 2001

By K Haga, G Danha, A Shibayama, L L. Godirilwe

The hydrometallurgical separation and enrichment processes provide an effective way to selectively recover metals from relatively dilute multicomponent sulfuric acid leach solutions. The multicomponent leach solution utilised in this study contained 0.3 g/L Cu, 0.34 g/L Ni, 0.13 g/L Co, and 2.96 g/L Fe, which was obtained after high-pressure oxidative acid leaching (HPOAL) of the copper-nickel smelter slag. The solvent extraction (SX), precipitation, and xanthate complexation processes were employed to recover and upgrade Cu, Ni, and Co from the leach solution. Batch SX tests were carried out using a countercurrent two-stage mixer settler extraction column, and LIX 984N (10 per cent v/v) as a copper extractant. Fundamental parameters influencing the extraction process such as pH, mixing speed, H2SO4 concentration, and organic/aqueous (O/A) phase ratio were investigated. For copper enrichment in solution, a combination of two extraction stages and two stripping stages were employed. Copper was successively separated from Fe, Ni, and Co under optimised extraction conditions (pH 2, 400 rev/min, O/A 0.25, and 20 min contacting) and stripping conditions (175 g/L H2SO4, 400 rev/min, O/A 4, and 20 min contacting). About 97 per cent of copper was extracted with low co-extraction of Fe, Ni, and Co of about 5.90 per cent, 1.47 per cent, and 2.53 per cent, correspondingly. A final Cu-rich solution containing 23 g/L Cu was obtained with a very low Fe concentration of 0.05 g/L. Additionally, for iron removal from the Ni/Co raffinate solution, more than 99 per cent of iron was precipitated at pH 4 by the addition of a calcium carbonate (CaCO3) suspension, with low co-precipitation of nickel and cobalt of around 3.68 per cent and 2.27 per cent, respectively. Furthermore, about 83.6 per cent of nickel and 99.4 per cent cobalt were co-precipitated from the solution by potassium amyl xanthate (PAX) solution at pH 6. The Ni and Co xanthate complexes were thermally decomposed and recovered as cobalt oxide (CoO) and nickel sulfide (NiS) solids.

Aug 24, 2022

By J Ta’ala, M Handyside

Mechanical sampling from conveyors has historically been a staple in the iron ore industry when information related to chemistry, sizing and moisture is required. In order to comply with ISO 3082:2009, samples can be taken either on a mass or time basis provided no bias is introduced by periodical variation in quality or quantity. With the introduction of mechanical sample carousels, you also have the opportunity to collect samples on a mass or time basis. In order to optimise automatic sample stations in a changing production environment, BHP Billiton Iron Ore (BHPBIO) has developed a simulation model that enables the various combinations of mass–mass, mass–time, time–time and time–mass to be investigated.The sample station model can utilise actual (variable) feed rates to achieve high resolution and enables the simulation of sample size variation. Cutter speeds and other settings can then be adjusted to better optimise the performance of the sample station with regards to optimal sample size as well as ensuring the sample station is in compliance with ISO 3082. The model can also assist process engineers in adjusting settings to better optimise the sample station and reduce unwanted events such as blockages. The model can be easily modified to conform to various sample station designs. This paper demonstrates the use of the model and the benefits that can be achieved.CITATION:Handyside, M and Ta’ala, J, 2014. Simulating time versus mass basis?sampling, in Proceedings Sampling 2014 , pp 155–164 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By M Rea, E O’Connell

Decarbonising explosives manufacturing and catalysing low-carbon mining supply is a significant global challenge. Low-carbon manufacturing precincts – clusters of geographically close businesses across multiple industries that share a goal of adopting firmed renewable energy and decarbonising process emissions – offer one potential solution. In an Australian first, Orica commissioned tertiary catalyst abatement technology in 2023 to mitigate greenhouse gas (GHG) emissions at its Kooragang Island (KI) facility in New South Wales (NSW), Australia. The EnviNOx® technology (ThyssenKrupp Industrial Solutions AG, Dortmund, Germany) used reduces nitrous oxide (N2O), a potent greenhouse gas arising as a by-product of nitric acid manufacture. As a result, mining customers in NSW are now benefitting from ammonium nitrate (AN) products that are almost 50 per cent less emissions-intensive than those Orica previously offered. The $37 million project is a private-public partnership that has involved partners across Federal and State government, global engineering and technology vendors, local community groups and local carbon advisors to overcome financial barriers.

Sep 1, 2024

The Lihir deposit in Papua New Guinea (PNG) contains an estimated mineable reserve of 454t (14.6M oz) of gold in refractory sulphide ore. The Lihir Joint Venture has submitted a proposal to the PNG Government to develop an open pit mine and to install a process plant and associated infrastructure facilities on Lihir Island. The proposed process plant will employ whole-ore pressure oxidation technology, has a design capacity of 2.825Mt/a of ore containing 7.20 sulphide sulphur, and is expected to average 19.3t/a (620,000 oz/a) in gold production during its first 12 years of operation.An extensive program of process development testwork and feasibility engineering was completed to establish the process plant design for the Lihir Project. Summary results of this test-work as well as key design criteria, the process flowsheet, and major equipment selected for the commercial plant are presented and discussed.

Jan 1, 1994

By M Randall, P Ebzery, F Burns, C Aisthorpe, P Blanz

SAG Mill process control classically maintains the SAG mill volumetric filling within a set operating range. Typically a SAG mill weight measurement, by either bearing pressure transducers or load cells, is used as an inferred measurement of volumetric filling. To maintain volumetric filling within a set operating range the SAG weight setpoint use for process control requires regular review due to changes in SAG mill charge density (rock:ball ratio) and the wearing of mill liners. At Lihir Gold Mine in Papua New Guinea, the use of SAG mill weight for process control is additionally complicated by compromised load cells and drifting bearing pressure measurements. The need for an improved method of measuring and controlling volumetric filling led to the recent installation of the Outotec MillSense, a SAG mill toe angle instrument. This paper presents the integration of the toe angle control in to the Lihir SAG mill process control philosophy as replacement for the traditional mill weight control.CITATION:Burns, F, Aisthorpe, C, Blanz, P, Randall, M and Ebzery, P, 2018. Toe angle measurement for SAG mill control at Lihir gold mine, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 59–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By C M. Standen

The SAG mill at Rasp Mine has undergone a number of liner design modifications since commissioning in 2012, making liner wear and failure difficult to predict from historical data. During 2017, several instances of liner failure or near failure were experienced resulting in unplanned downtime for emergency relines or to patch liners in the lead up to a planned shutdown. The strategy for relining mills is often to minimise the frequency of relines (and subsequent shutdown costs) by extending liner life, achieved through design modifications. However, it was observed that as the Rasp SAG mill liners wear, mill performance declined with power draw increasing and throughput declining. Opportunity and inefficiency costs start to erode the revenue per additional tonne milled for a given set of liners, and in turn the benefit of delaying relines. As such, optimising the frequency of relines becomes a trade-off between reline costs and opportunity/inefficiency costs in delaying relines. The aim of this paper is to demonstrate a frame work for analysing costs using a marginal economic analysis with the assumption that the Law of Diminishing Returns can be applied to the life of mill liners. The SAG mill operating variables can be modelled to determine their impact on costs and an optimal reline point can be defined where the total costs are minimised. This prevents unexpected failures due to accelerated wear by providing justification to reline earlier and thereby allowing efforts to be focused on sustaining milling performance.CITATION:Standen, C M, 2018. An economic approach to optimising mill reline frequency – a case study of SAG mill relines at Rasp mine, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 197–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

The Mt Todd Project is located 42 km northwest of Katherine in the Northern Territory. The identified mineral resource estimate for the Batman gold deposit is 66.7 million tonnes (Mt) grading 1.4 grams/tonne (g/t). Proved and Probable Ore Reserves total 42.3 Mt grading 1.5 g/t. Orebody definition and reserve estimation is based on extensive percussion and diamond drilling. Exhaustive bias analysis comparing grades produced from different drilling techniques has been undertaken. Similarly, detailed check assaying programs have been run to validate grade data produced by commercial laboratories used during the exploratory drilling phase. Significant biases were established from both studies and appropriate 'corrections' were made to drillhole databases prior to final resource and reserve estimation. 3D geostatistical modelling has been utilised for resource and reserve estimation, with specialist consultants contracted for this work. At all times, interpreted geological controls on mineralisation, provided by

Jan 1, 1994

By C R. Ure

To substantially reduce, if not eliminate, carbon dioxide (CO₂) emissions from ironmaking it is necessary to convert from blast furnace (BF) ironmaking using coking coal as the reductant to direct reduction (DR) ironmaking using hydrogen (H₂) and green electricity. Currently, almost all natural gas (NG) based direct reduced iron (DRI) production utilises iron oxide pellets in shaft furnaces, as opposed to fines in fluidised beds. Also, these pellets are ordinarily produced from high-grade magnetite concentrate, rather than hematite and goethite with typically higher gangue contents. The use of high-grade magnetite concentrate is driven by the preference to melt DRI in conventional electric arc furnaces (EAFs), thereby avoiding the basic oxygen furnace (BOF) for making crude steel (CS). However, in replacing BF with DR ironmaking it is not economically feasible to source enough high-grade magnetite to replace the lower grade hematite and goethite currently consumed. That is not to say that hematite and goethite, or even low-grade magnetite, cannot be used in DR ironmaking. However, their higher gangue content, resulting in higher slag production, requires that the EAF producing CS be replaced with a submerged arc furnace (SAF) that will produce pig iron (PI) for the BOF as does the BF. Here, critical issues to be addressed are, what are the technicalities in replacing high-grade magnetite concentrate with hematite and goethite and NG with H₂ in DRI pellet production and melting? This paper summarises certain relevant published information on DRI pellet research, test work and production together with relevant information on Pilbara ores. It attempts to illustrate the inter- relationship of composition and processing conditions on DRI pellet properties. It is intended to serve as a rudimentary guide to understanding the complexities of formulation, testing, evaluation, production and goethite and offer insight into this challenge.

Sep 18, 2023

By C Smith, R I. Maczkowiack, P D. Erskine

Open cut coal-mining has been conducted in the Bowen Basin region of central Queensland for almost five decades, and has disturbed an estimated area of 140 000 ha of agricultural land until 2011. Approximately one-third of the area disturbed by mining has been rehabilitated to pastures or bushland. However, none of the rehabilitated land has yet been assigned a specific end-use. This research project develops an approach for assessing end-use risks for the regionÆs mined land, and develops risk assessment models for selected end-uses. First, a web-based survey of stakeholders was used to identify risks to be assessed. The risks identified were surface erosion, subsurface erosion, bushfires, weeds and feral animals. The survey also identified possible end-uses of bushland and grazing. Second, conceptual risk models were developed based on the risk assessment concepts of likelihood and consequence specified in the Australian and New Zealand risk assessment standards. Likelihood was modelled using site characteristics and management factors that influence the occurrence probability of risks (eg surface erosion), while consequence was modelled using a set of site condition indicators and condition thresholds (changes in root-zone water-holding capacity, soil erodibility, vegetation ground cover and soil organic matter and transition probability to a non-preferred ecosystem type).The factors influencing likelihood and consequence for each risk have been integrated using Bayesian networks. The next step in model development is to parameterise the Bayesian networks using existing equations, empirical datasets, or expert opinion where data are not available. The parameterised models will be used to assess grazing and bushland end-uses against erosion, bushfire, weed and feral animal risks for rehabilitated mined land sites, with the purpose of identifying the relative risks associated with each end-use, and the landform design specifications and land management practices under which end-use risks are minimised.CITATION:Maczkowiack, R I, Smith, C and Erskine, P D, 2012. Risk assessment models for post-mining land use, in Proceedings Life-of-Mine 2012, pp 33-42 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By Baird G. R, Jurak R. N

In this study Dynamic Finite Element Modelling is used to investigate the distribution of peak particle accelerations (PPA) induced in a rock mass by a vertical decked column of explosives. The rock mass is assumed to be viscoelastic. The influence of the delay time between decking charges, the viscosity attenuation (quality factor Q), the decking configuration, and the velocity of detonation (VOD) on PPAs is examined. The results of this paper are relevant to fragmentation since the nature of the fragmentation is related to the stress magnitude and hence the PPAs. It was found that increasing the VOD, and increasing Q increases the PPAs in the neighbourhood of the blasthole. However, the VOD and rock quality factor Q have little influence upon the distribution of PPA. It was also found that an even distribution of PPAs, at a fixed distance from the blasthole, could only be obtained by increasing the ratio of charge length to stemming length. The study showed that the amplitudes and distribution of PPA surrounding the blasthole was approximately independent of the delay time between the decked charges. The modelling also shows that the particle accelerations at locations below the bottom of the charge are relatively small and so the model predicts no substantial damage below the bottom of the charge after blasting.

Jan 1, 1995

By V P. Beskrovnaya

Tests for the development of a metals recovery technology from samples of a Russian gold-bismuth deposit were carried out. Gold, silver and bismuth assay reported 5.6 g/t, 3.0 g/t and 0.08 per cent, respectively. Two flow sheet options were pilot plant tested: gravity/cyanidation of gravity tailings with subsequent flotation of cyanidation/carbon-in-pulp (CIP) tailings, and gravity/flotation concentration with cyanidation/CIP of concentrates. Option 1 results showed lower gold, silver and bismuth recoveries (81.3 per cent Au, 55 per cent Ag and 74.0 per cent Bi) due to low flotation efficiency for cyanidation tailings. Therefore, a flow sheet involving gravity/flotation concentration to produce bismuth-gold concentrates (0.8 per cent Bi) with subsequent cyanidation/CIP was recommended. Gold, silver and bismuth recoveries obtained by this method to the combined gravity/flotation concentrate were 90.2 per cent Au, 83.3 per cent Ag and 80.2 per cent Bi of the ore, respectively. Overall gold, silver and bismuth recoveries were 83.0 per cent Au, 40.5 per cent Ag and 80.2 per cent Bi, respectively. Gold and silver recoveries to the cathode precipitate were 92 per cent Au and 48.6 per cent Ag (per operation). Reagents consumed for flotation were 0.1 kg lead acetate/t ore, 0.4 kg butyl xanthate/t ore, 0.2 kg T-80 frother/t ore, 0.02 kg sodium hexametaphosphate/t ore, 0.15 kg copper sulfate/t ore. Reagents consumption for cyanidation was 0.42 - 0.48 kg NaCN/t ore and 0.2 kg CaO/t ore. It was recommended to deliver bismuth concentrates after hydrometallurgical treatment to a smelter. Overall bismuth recovery including bismuth recovery achieved by pyrometallurgy was 60.0 per cent. However, it was obvious that delivery of bismuth concentrates to a smelter and their commercial treatment would be very expensive due to relatively high mass pull of bismuth concentrates (7.6 per cent of the ore weight). For this reason, thiourea leaching and hydrochloric acid leaching with subsequent cyanidation/CIP were investigated as alternatives to cyanide leaching. These two alternatives were proposed to enable optimal recovery of valuable metals from concentrates on-site. Recoveries obtained by thiourea leaching were 91.2 per cent Au, 90.5 - 91.9 per cent Bi and 77.0 - 78.1 per cent Ag. However, that method required considerable capital and operating costs. As an alternative, hydrochloric acid leaching with subsequent cyanidation was investigated. Test results showed improved gold, bismuth and silver recoveries, which were 94 - 95.9 Au per cent, 94 - 96 Bi per cent and 76 - 78 Ag per cent, respectively. Hydrochloric acid consumption was 100 kg/t concentrate or 7.6 kg/t ore. Current efficiency during electrowinning was about eight to 12 per cent. A recommended flow sheet involving hydrochloric acid leaching of concentrates, electrowinning of bismuth from solutions, recycling solutions after electrowinning and cyanidation of hydrochloric acid leaching cakes is described. Overall recoveries achieved by the proposed flow sheet were as follows: 84.8 - 86.5 Au per cent, 75.8 - 76.9 Bi per cent and 63.2 - 64.9 Ag per cent. Based on results from these tests, initial data for a bankable feasibility study and plant designing were developed.

Jan 1, 2007