Search Documents

By A. W. Schlechten, W. J. Kroll

As this paper is written, the only method for the commercial production of lithium metal is by the fusion electrolysis of LiC1-KC1 mixtures, as first proposed by Gunkz.2 The details of the industrial process have not been made public hut Osborg8 stated that an efficiency of more than 90 pct is obtained with a lithium metal recovery above 95 pct and that the metal is 99.5 pct pure. Pletenev9 gave a power consumption of 66 kw-hr per kilogram of lithium metal produced with a salt consumption of 9 kg of LiCl and 0.4 kg of KCI. Pletenev's figures indicate a somewhat lower recovery than that given by Osborg. In a recent report on' German lithium plants, Motock7 gives figures that are also less favorable than those reported by Osborg. At the German plants the lithium recovery in electrolysis was only 83.4 pct, with a power consumption of 140 kw-hr per kilogram of lithium. The metal averaged only 97 pct pure, with sodium and potassium as the chief impurities. The presence of SO2, SO3, SiO2, Ba, Ca, and appreciable amounts of Na and Fe2O3 were especially disturbing in the electrolysis, and it was necessary to run the cell for some time to eliminate most of these impurities and condition the bath. It may be noted here that most of these impurities do not interfere with a thermal reduction process. These facts show that the present method of producing lithium is fairly efficient and would suggest that other methods could not compete. However, fusion electrolysis has certain drawbacks, such as the necessity of supplying costly, low-voltage direct current and of collecting and processing the anodic chlorine if it is not to be wasted. An even greater disadvantage is that lithium chloride must be used for an electrolyte. It is one of the most expensive salts of lithium, since it cannot be produced in anhydrous form by precipitation from aqueous solution, as is done with LiF or Li2CO3. The reduction of lithium by a vacuum process similar to the ferrosilicon method for the production of magnesium would have certain advantages. Small units such as Pidgeon retorts, would give flexibility of production to meet demand, and a small plant would require moderate capital outlay. There is a possibility of using idle Government-owned magnesium plants for such purposes. The raw materials needed for vacuum thermal reduction would not have to be extremely pure, Director, with respect to the iron and calcium Content. This paper describes a series of experiments to determine the effectiveness of various agents for the reduction of lithium compounds. The investigation is part of a program of vacuum metallurgy con-

Jan 1, 1949

By Irving Palmer

DURING the past 15 years in this country there have been few additions to the literature of lead smelting. After the consolidation of the principal smelting companies at the beginning of this period it became the policy of the larger company not to permit the publication of details in regard to many of its metallurgical processes. This led to similar action on the part of some of its competitors. The result, of course, was a decided decrease in the number of papers written upon the practical side of the subject. Even upon the theoretical side the contributions have been few. It would seem that the industry as a whole has suffered from this general unwillingness to exchange information. While it is true that a given company is entitled to the reward that may come from its own development of a new process, it is also true that a still greater reward might be the result of a free exchange of ideas with other plants. This principle has been recognized for a long time in other metallurgical industries, notably those engaged in the smelting of iron and the manufacture of steel. It is pleasing to note that the leading lead-smelting company has very recently decided to modify its policy of secrecy, and to permit the publication of papers covering some details of its metallurgical methods. The statement has been made that there has been but little progress in lead smelting during the period just referred to. This impression is due in part to the scarcity of papers written on the subject. There has been, it is true, some discussion of the new sintering processes, but with little reference to detail, and to the effect that blast roasting has had upon the industry as a whole. In spite of the prevailing belief, it may be said that lead smelting, in common with other metallurgical industries, has made steady and substantial progress. It is the purpose of the present paper to discuss briefly some features of the industry as it is now conducted, with special reference to the blast-furnace practice in the larger silver-lead smelting plants of the United States and Mexico.

Jan 7, 1914

By R. E. Old

Through the use of pressure and production records, formation properties and bottom-hole sample data, the performance of an oil reservoir may be studied analytically to define and evaluate the natural forces acting on and within the reservoir. Use is made of material-halance methods and the equations for natural water encroachment. to estimate reserves. Methods for calculation of pressures are given. A study of the Jones sand, Schuler field, Arkansas, has been made and is given here to illustrate the value of the methods discussed. Introduction With the decreasing rate of discovery of new oil reserves, attention is necessarily focused on the efficient development, evaluation, and production of existing reserves. From the nation's viewpoint, the necessity of conserving resources is obvious. From the operator's viewpoint, the problem is to lengthen the period of profitable operation, in an attempt to increase the return on his investment. To do this the operator must take advantage of the natural forces acting on and within the reservoir. Natural water encroachment, the nemesis of profitable operation in the past, can be and is being harnessed to produce a greater oil recovery during the stage of flowing production. Proper evaluation of water encroachment rates and a fuller under- standing of reservoir behavior dictate the appropriate production procedures. Complacency in hit and miss production is obsolete. Oil production must and will approach the efficiency of other businesses, such as manufacturing. A manufacturer will not place an article on the market until he has fully investigated the processes involved, additional investment in equipment, costs of production, and expected profits. These may be modified by actual experience at a later date, but at least he begins with an idea of expected return. It is just as logical that an oil operator should investigate these same factors during the development and the early period of production of an oil reserve. The complexity of the problems existing in oil reservoirs should not be underestimated. Conversely, they should not be regarded as insoluble. Many completely defy solution, but there are others that can be solved completely or attacked intelligently to yield approximate results. The petroleum engineer has many tools, both figuratively and literally, at his disposal. Physical data such as core analyses, electrical logs, bottom-hole sample analyses, and bottom-hole pressures are accumulated extensively. Advances in the analytics of fluid flow have kept pace with the advances in measurement of physical data. It is the purpose of this paper to show how some of these records may be analyzed to define certain phases of reservoir behavior.

Jan 1, 1943

By R. E. Old

Through the use of pressure and production records, formation properties and bottom-hole sample data, the performance of an oil reservoir may be studied analytically to define and evaluate the natural forces acting on and within the reservoir. Use is made of material-halance methods and the equations for natural water encroachment. to estimate reserves. Methods for calculation of pressures are given. A study of the Jones sand, Schuler field, Arkansas, has been made and is given here to illustrate the value of the methods discussed. Introduction With the decreasing rate of discovery of new oil reserves, attention is necessarily focused on the efficient development, evaluation, and production of existing reserves. From the nation's viewpoint, the necessity of conserving resources is obvious. From the operator's viewpoint, the problem is to lengthen the period of profitable operation, in an attempt to increase the return on his investment. To do this the operator must take advantage of the natural forces acting on and within the reservoir. Natural water encroachment, the nemesis of profitable operation in the past, can be and is being harnessed to produce a greater oil recovery during the stage of flowing production. Proper evaluation of water encroachment rates and a fuller under- standing of reservoir behavior dictate the appropriate production procedures. Complacency in hit and miss production is obsolete. Oil production must and will approach the efficiency of other businesses, such as manufacturing. A manufacturer will not place an article on the market until he has fully investigated the processes involved, additional investment in equipment, costs of production, and expected profits. These may be modified by actual experience at a later date, but at least he begins with an idea of expected return. It is just as logical that an oil operator should investigate these same factors during the development and the early period of production of an oil reserve. The complexity of the problems existing in oil reservoirs should not be underestimated. Conversely, they should not be regarded as insoluble. Many completely defy solution, but there are others that can be solved completely or attacked intelligently to yield approximate results. The petroleum engineer has many tools, both figuratively and literally, at his disposal. Physical data such as core analyses, electrical logs, bottom-hole sample analyses, and bottom-hole pressures are accumulated extensively. Advances in the analytics of fluid flow have kept pace with the advances in measurement of physical data. It is the purpose of this paper to show how some of these records may be analyzed to define certain phases of reservoir behavior.

Jan 1, 1943

By E. R. Darby

When bronze is melted in open-flame furnaces a considerable amount of slag is formed during the melting operation. This slag may be incidental to the melting practice or it may be formed intentionally by slag-forming constituents added to the furnace charge to provide a covering for the melted metal When this slag is removed from the furnace, it contains, in addition to the free metal carried with it by the skimming operation, a considerable amount of metal as oxide either combined or mechanically mixed with it. By the usual crushing and washing methods this metallic oxide generally goes to the tailings pile, so diluted by other foundry waste that its recovery is economically impossible. If this furnace slag is not inixed with other foundry waste, practically all of the metal oxide as well as the free metal may be recovered by some form of smelting operation. The first side of the problem to be considered is the amount of slag produced. It may not be true that the majority of foundries have no record of the amount of slag made, but it is certainly true that a very great many either have no record or pay little attention to it. Usually the collection of furnace slag for one normal week's run will be sufficient to determine the advisability of its being handled in a different manner from the crushing and concentrating generally employed. If a large representative sample of the accumulation is crushed and concentrated and the recovery compared with the results of a careful assay, it will be found that a large percentage of the total metal content was lost in the washing process. The percentage of loss will be greater than the metallic oxide content, as some free metal in extremely fine particles always is carried away in grains of slag. From such a comparison, it may be determined whether or not the slag should be melted, sold or treated as before. An example of an actual test of this kind is given below. In a foundry melting 50,000 to 80,000 Ib. of bronze per day, a week's accumulation of furnace slag and ladle skimmings amounted to 16,500 1b.—over three times as much as the foundry superintendent estimated before the accumulation was made. Two tons of this material was taken as representative of the lot. This was ground through a thoroughly cleaned ball-mill and concentrated over a Wilfley table. The

By N. M. Langdon

INTRODUCTION. IN considering the magnificent success of Mr. Gayley's Bold experiment of applying dry blast to the blast-furnace, whereby , saving of 20 per cent. of fuel per ton of iron is effected, the question arises whether, still further economy in fuel is possible, and, if so, how it is to be attained? The manner in which the heat generated in the furnace is utilized in the production of pig-iron may be determined, by the method of Bell and Gruner, for any furnace for which the necessary data are obtainable ; and the study of the operation,. tinder various conditions, of a number of furnaces, for which such information has been worked out., should enable us to form some conclusion on the subject. The tables and calculations given below cover the operations of several furnaces reported in our Transactions; also the two furnaces using natural and dry blast in ,Mr. Gayley's experiment, for which the heat-equation has been worked out by Prof. Joseph W. Richards in his admirable discussion' of Mr. Gayley's paper, The Application of Dry Air Blast to the Manufacture of Iron, and, finally, various hypothetical furnaces.. The full list is as follows : A. Isabella furnace, with natural blast. B. Isabella furnace, with dry blast. The data stated. for A and B in Table III. are those given by Professor Richards; except that the heat-units are given for one unit of iron instead of 100 units, and some items of heat supplied, as stated by Richards, have been subdivided, the total being the same as given by Richards. (Columns A and B are introduced in Table III. for comparison with C and D.)

Oct 1, 1909

For the benefit of those of our members who are considerable holders of securities,but owing to their isolated situations are not in close touch with the metropolitan market and current quotations, we are publishing two very interesting graphs, showing the course of the bond and stock markets in New York over a long period. These graphs are furnished through the courtesy of the financial department of the New York Tribune.

Jan 11, 1919

By M. J. Mullikin, J. B. Conway

Equations capable of representing combined first -and second-stage creep behavior include the Andrade, Cottrell-Aytekin, Garofalo, and de Lacombe equations along with a third-degree polynomial in t1/3. Employing some recent high- temperature creep data for arc-cast tungsten the effectiveness of these expressions was evaluated. It was found that, in this instance, the most accurate representations were afforded by the third-degree polynomial in t1/3 and the de Lacombe equation. Also noted was the fact that the Andrade equation gave results just slightly inferior to those obtained with the third-degree polynomial, definitely better than those due to the Cottrell-Aytekin equation, and slightly superior to those furnished by the Garofalo equation. EXPRESSIONS designed to describe combined first -and second-stage creep behavior must possess certain specific characteristics. At time zero the equation must reduce to a strain value corresponding to the instantaneous deformation on loading. Then in the early moments following load application transient-creep behavior must be described to reflect a creep rate which constantly decreases with time. And finally at larger time values linear (or at least nearly linear) strain-time behavior must be accounted for to yield the steady state or minimum creep rate. Some equations, such as the one based on the parabolic creep law, yield fairly satisfactory results in transient analyses but are not effective at all when combined first- and second-stage data are to be analyzed. Other equations give equally accurate results in both instances although in general the complexity of the equation is slightly increased. For example the Andrade1 equation: has found fairly general application in expressing first-stage creep behavior. Furthermore the contribution of the exponential term becomes more and more prominent as the time increases and causes this equation to exhibit a point of inflection at large values of time. With a proper selection of equation constants the curve can be made fairly flat in the region of the inflection point indicating a desirable equation form for combined first- and second-stage creep analysis. Another equation form with the proper characteristic is that of Cottrell and Aytekin:2 e =a +bt1/3 +ct [2] Obviously as time increases the first derivative of this expression approaches a constant value to suggest application to combined first- and second-stage creep analysis. Similarly a third-degree polynomial in t1/3: e -a + bt1/3 + ct2/3 +dt [3] has the same characteristics. Expressions of this type have been shown3 to be very effective in the analysis of transient-creep behavior and the fact that the first derivative has the same characteristic as Eq. [2] suggests use in the combined analysis.

Jan 1, 1967

By G. Thodos, R. B. Grieves

A method has been developed for the accurate calculation of the cricondentberm and cricondenbar temperatures of multicomponent hydrocarbon mixtures of known composition. The mixtures may contain any number of components including paraffins and isoparaffins, olefins, acetylenes, naphthenes and aromatics. This approach is based upon the mole fraction of the low-boiling component in the mixture and graphically presents the ratios of the cricondentherm and cricondenbar temperatures to the pseudocritical temperature as {unctions of a boiling-point parameter. The only requirements are the critical temperature, normal boiling point and the approximate vapor pressure behavior of each component. For mixtures of more than two constituents a stepwise calculation procedure is necessary where the pseudocritical temperature is based upon the critical temperature of the pure low-boiling component and upon the actual cricondentherm or cricondenbar temperature of the mixture of all the remaining higher-boiling components. From an analysis of 22 binary systems (123 compositionsl, the average deviation of calculated cricondentherm temperatures from reported values is 0.87 per cent, based on degrees Rankine; and for 10 multicomponent mixtures containing from three to six components, the average deviation is 0.98 per cent. From an analysis of 18 binary systems (104 compositions) the average deviation of calculated cricondenbar temperatures from reported values is 0. 79 per cent; and for 15 multicomponent mixtures, 1.47 per cent. Equations, derived from the graphical relationships, are presented which enable rapid calculations for both binary and multicomponent systems. INTRODUCTION With the increasing tendency towards the use of high pressure processes, the need for an accurate method of calculation of the properties of a multicomponent hydrocarbon mixture in the critical region is becoming more essential. Critical region phase relations are also significant in gas condensate reservoirs, for which a knowledge of the fluid phase boundaries and regions of retrograde condensation make it possible to evaluate optimum operating conditions. The possibility of liquefaction in the underground structure may be established, and information on the feasibility of the use of repressurizing may be determined. A typical phase diagram for a multicomponent hydrocarbon mixture is presented as Fig. 1. This figure also shows the regions of retrograde behavior encountered by following lines AB and AC. If accurate methods of calculating the temperatures and pressures at the critical, cricondentherm (maximum temperature) and cricondenbar (maximum pressure) points of multicomponent hydrocarbon mixtures of known composition were available, it would be possible to estimate closely the entire phase diagram of any mixture. Several methods have been presented in the literature for the estimation of the critical temperatures and pressures of multicomponent mixtures containing all types of hydrocarbons and including the fixed gases.4-8,21 Considering the cricondentherm and cricondenbar points, the work is more limited. Etter and Kay5 have developed rather complex equations for

By Tasuku Fuwa, John Chipman

Equilibrium data on the reactions of gases with carbon and oxygen dissolved in liquid iron are reviewed and correlated. A source of error in oxygen analysis of graphitic samples is exposed. New experimental data on the oxygen content of high -carbon iron in equilibrium with carbon monoxide indicate that the activity coefficient of oxygen is decreased by additions of carbon. The carbon-oxygen product decreases slightly with increasing carbon content. In recent years a number of investigations have been reported dealing with the equilibria between carbon and oxygen in liquid iron and gases containing carbon oxides. The laboratory study of these reactions dates back to 1931 with the publication of a paper by Vacher and Hamilton' on "The Carbon-Oxygen Equilibrium in Liquid Iron". The principal object of this study was to obtain data on the reaction shown by Eq. [3] below; their data and others by vacherZ permit evaluation of the other equilibrium constants as well. Subsequent studies have been reported by Matoba, Phragmen and Kalling and by Marshall and Chipman.5 The equilibria may be expressed by the following three equations: C + CO,= 2CO;Kl = Pc° [1] 0-+CO = CO,;K2=-P co, "0.PCO c + O = CO; K3 = In the equilibrium constants, ac and a0 are taken as equal to [% C] and [% 0] respectively in the infinitely dilute solution. At finite concentrations an activity coefficient is introduced such that ac =fc [%C], and so forth. It is to be noted that these equations represent only two independent relations, the third being derivable from any two. Richardson and Dennis have determined the conditions of equilibrium in reaction [I] at temperatures of 1560" to 1760°C. Their results have been confirmed by Rist and chipman7 who have shown how the data may be extended to cover the entire range of liquid compositions at temperatures from the eutectic up to 1760°C. An approximate confirmation has been reported by Fuwa and chipman.' These investigations also established the activity coefficient of carbon which was shown to increase rather rapidly with increasing concentration. For the very dilute solutions the value of Kl is expressed in the equation: log^i = - 7280/T+ 6.65 This equation leads to a value of Kl = 430 at 1540° C in excellent agreement with the average value of Marshall and Chipman.5 It is shown as line 1 in Fig. 1 together with the experimental observations. In the case of reaction [2] the direct experimental results can be supplemented by observations on the corresponding reaction with hydrogen, namely reaction [4]:

Jan 1, 1961

By Dogan E. Gücer

In the following note, with the help of a new parameter of strain hardening, the attention is drawn to the close relationship between the relative performances of steels under plastic range cycling and their strain hardening characteristics. If a cantilever beam of rectangular cross section is tested with the arrangement shown in Fig. 1 in reversed bending between constant deflection limits at the lever head, the longitudinal strain-deflection hysteresis shown in Fig. 2 is obtained. There is no lateral strain due to constraint at the rectangular test section.' If the absolute value of strain undergone between a maximum state of tension and maximum state of compression is called A, it will be seen that A decreases with cycling rapidly due to the strain hardening in the test section and the ensuing change in the bent beam profile. It will also be seen that A reaches an approximately stable value around 10th cycle. If we call the first cycle strain range, A,, and that of 10th cycle, A,,, then is an index of the strain hardening capacity at a particular deflection level. A plot of n vs ? is reproduced in Fig. 3 for two ASTM steels: A-302 and A-201. A-302 is a low alloy structural steel, A-201 a low-carbon steel. The specimens were first normalized at 1650°F for 75 min then grooved with a milling cutter; and the notches were ground to 50G finish. The final operation before testing was a stress relief at 1150°F for 75 min. The behavior of the two steels changes around ?1 = 0.8 pct or A,, = A, -n = 0.7. If these curves are compared with the endurance life curves given in Fig. 4, it will be seen that the relative performance of the two steels also change around A,, =. 0.70 pct. The steel with lower strain hardening capacity (7) at a certain strain level shows a longer endurance life, irrespective of their strength levels. Since the exponent governs strain hardening at lower strain levels than the Modulus, the relative values of both parameters also coincide with the change in n values and the relative performances of the two steels at different strain levels. These two observations indicate to the close relationship be-

Jan 1, 1962

By AIME AIME

WITH the recent increase in the price of gold, its economic recovery at depths formerly considered impractical has become a present possibility. Two important difficulties must be met: pressure bursts of the rock, and the reduced efficiency of human labor subjected to the higher temperatures and the increased humidity at the greater depths. In the following abstract of a paper by J. H. Dobson, presented before the South African Institution of Engineers on

Jan 1, 1935

By C. D. Haynes, S. C. Gambrell

The practice of roof bolting in WORLD-WIDE mining activities is very well-known, having been used extensively for over 50 years. The theory of roof bolting, however, is extremely complicated, and only recently have investigators attempted to explain the theory. Various means of stress analysis have been utilized in rock mechanics, most of which reduce rock to an isotropic, homogeneous medium that can be easily analyzed. One of the indirect research methods is the photo-elastic technique, the theory of which is widely known and needs no elaboration. This technique has been used extensively to examine the state of stress around underground openings of various shapes in certain types of strata, and under various loading configurations.'-" In-Situ Mine Roof Trusses The photoelastic technique was employed here to evaluate the state of stress above a mine opening where support is provided by the in-situ mine roof truss. This support configuration, shown in Fig. 1, has gained popularity in recent years, particularly in mines with bad roof conditions." To the authors' knowledge, no scientific determination has been made of the advantages roof trusses may offer over conventional bolting configurations comparable to roof trusses. Ordinary mine roofs usually sag or bulge downward soon after mining. Normally, after some movement the roof begins to stabilize, but the face of this bulging mine rock is usually in tension and will almost always fail unless supported. Because rock fails easily in tension, it is desirable to "preload" the roof, that is, to impress a compressive force on the mine roof to prevent bulging and subsequent tensile failure. Ordinary rock bolting installations, particularly if the bolting is perpendicular to the mine roof plane, do not produce a preloading effect. Although bolting installations squeeze the strata together and produce a beam effect desirable for support, they do not have the advantage of actual uplift. They pull down at the anchorage point with a force equal to the bolt tension which sometimes causes a separation in the plane of the anchorage detrimental to roof strength. In-situ mine roof trusses require the installation of steel tension rods in the roof of the mine much the same as conventional roof bolts, except that the rods are arranged to produce a stress pattern above the upper surface of the opening similar to that of a prestressed beam. The roof rock acts to transmit the compression force. The simplest form of truss consists of two steel rods anchored to the back of holes drilled at an angle of approximately 45 over the mine pillars. These rods are collared near the middle of the room, and the lower ends of the rods are connected by tie rods and turn-buckles. Used in this manner, a small-diameter steel rod can provide essentially the same support as a wide-flange steel beam. By tightening the turnbuckles, an uplift on the roof can be produced. Objective of the Investigation The objective of this investigation was to determine qualitatively the state of stress that exists above a mine roof after the installation of the in-situ mine roof truss vs. that of two angle roof bolts, hereafter referred to as "roof bolts," drilled and placed in the same configuration, that is, 45" above each pillar and connected together in the middle of the room by a bearing member such as a steel beam. Each state of stress was to be identified, insofar as possible, as compression or tension above the mine opening. Model Construction A photoelastic model of a mine opening was coil-structed from -in. thick PLM-4B birefringent plastic and was machined to specification shown in Fig. 2. The dimensions of the opening were chosen to simulate a width-to-depth ratio of 3 to 1. Two % -in. holes were drilled at 45" angles, as shown, to provide for the loading devices. After construction, the model was annealed at 240°F to remove stresses produced during machining.

Jan 1, 1971

A record $18.7 billion worth of metals, non- metals and fuels was produced in the U.S. during 1962, according to a year-end estimate from the USBM. The 1962 total value, based on preliminary statistics compiled by the Bureau, was nearly $600 million more than in 1961. Most minerals gained both in value and volume of production during 1962 according to information collected by the Bureau. All mineral fuels except anthracite showed increases. Among nonmetallic minerals- other than fuels-gains exceeded losses by two to one. Metal production held steady as gains and losses balanced.

Jan 2, 1963

By Euzebio De Oliveira

ONE of a recent batch of samples from the Serra da Baliza, in the state of Parana, Brazil, contained asphalt and a dark heavy oil; and workmen on the railway from Porto União to Uruguay discovered asphalt, coming from eruptives that outcrop along the Rio de Peixe. The occurrence f asphalt in the triassic eruptives of southern Brazil, however, has been known a long time, according to Dr. Gonzaga de Campos. It is generally believed that the Botacatú sandstone is always a hard vitrified rock, from the metamorphic action f. the overflowing eruptive contacts. In this region, however, the contact metamorphism is almost nil; the sandstone is slightly hardened in a narrow zone about 20 to 30 cm. wide. In many places, the sandstone is so friable as to be easily reduced to sand, which is used-.in, mortar for building in Guara-puava and Palmas. South and west from Porto União,. this bench of sandstone is about. 50 m. thick, and is capped by a heavy bed. f basic eruptives, many of which are amygdaloids. Dr. Geo: P. Merrill, after studying the triassic eruptives collected by the Coal Commission, reached the conclusion that. "All these rocks are of typical basalt-diabases, not in any essential different other than in structure. An interesting mineralogical phase is its paucity in olivine, which in many cases is completely lacking. Professor Hussak, who carefully studied these rocks and their accessory minerals, decided that in the dikes they are granular (diabase) and, that in the lava sheets, porphyritic (augite-porphyrite or melaphyre), and that the latter pass evidently to normal diabases and are always typical of effusive rocks. The examination f many slides from dikes and sheets leads us to adopt the opinion of Professor Hussak; the rocks of the dikes are of ophitic structure, while that of the sheets show a great variety f structure and may vary from almost granular to basaltic. The great paucity in olivine had been noted by Hussak, who classes as melaphyres, the porphyritic triassic rocks in Brazil which contain olivine.

Jan 4, 1921

By D. H. NETLAND

DURING the year 1907 an investigation of the Clinton formation in New York has been carried out under the direction of the State Geologist, and a full account of the results has been prepared for publication.1 The more important economic features of the report are summarized in the present paper. Previous knowledge of this, the type, section of the Clinton has been contributed mostly by Hall and Vanuxem in their reports for the Natural History Survey of New York, which were issued in their final form in 1842-43. Brief accounts of the ore-occurrences have been given by B. T. Putnam,2 J. C. Smock,3 A. H. Chester,4 and E. C. Eckel.5 Prof. C. H. Smyth, Jr.,6has discussed the origin of the Clinton ores in two papers, which, so far as the local occurrences are concerned, have removed all doubt that may have existed on that subject. Distribution of the Clinton Formation. The Clinton strata in New York State are restricted to a single belt, Which extends from the eastern central part to the Niagara river, which it crosses, and thence continues for some distance into the province of Ontario. The New York

Mar 1, 1909

Jan 1, 1897

By TENNEY C. DeSOLLAR

TRADITION tells us that the earliest use of Alabama iron was to make shoes for the horses of General Andrew Jackson and his men during the first part of the nineteenth century. The first recorded incident in the making of iron was the request of U. S. Indian Agent Benjamin Hawkins "that a crew of blacksmiths be sent to the Creek Nation in the lower Mississippi territory." These frontiersmen made up the first body of pioneer iron makers in the territory. The first known blast furnace was built by Joseph Heslip in 1818 at Russellville, named after Major William Russell, who was General Jackson's chief of scouts. The Tannehill furnace was built in 1830 in what is now Tuscaloosa County and its ruins, as shown above, can be seen today.

Jan 1, 1937

By J. Richter, D. Schulze

J. Richter and D. Schulze (Deutschen Akademie der Wissenschafte zu Berlin)—Introduction. In a recent paper R. G. Garlick and H. B. Probst reported on experimental results of investigations of room-temperature slip in zone-melted tungsten single crystals.17 In the paper it was pointed out that slip lines could be detected with an optical microscope only after about 10 pet plastic strain of the crystal. In our investigations we could observe slip lines in tungsten single crystals of defined orientations already with an elongation of 0.02 to 0.03 pet.18"9 Experimental Technique and Results. The tungsten single crystals were produced from 4 to 5 mm sintered rods* as starting material by electron- beam zone melting. With single-zone-pass melting a speed of 0.5 mm per min was used, while three-pass melting could be handled at a speed of 3 mm per min. Crystal axis orientations were located in the shaded area of the stereographic triangle, see Fig. 6. Orientation 1 is located at about 18 deg and orientation 2 at about 5 deg on the great circle from [011] to [ill]. This corresponds approximately to the orientations P and M referred to by Garlick and Probst. Our single crystals had a length of about 70 mm and were profiled solely by electrolytic means, leaving grip ends at both ends of the crystals. Between the latter, a cylindrical crystal of 45 to 50 mm length and about 2.4 mm diam was obtained. The crystals were deformed at room temperature in a commercial tensile-testing machine to obtain a strain of 0.02 to 5 pet. The average strain rate e = eP/t for all tensile tests amounted to approximately 10 -6 to 10-5 per sec, with ep representing plastic strain and t the duration of applied stress. In Fig. 7 a crystal is shown elongated by 0.03 pet. The picture was obtained by means of an optical microscope. Figs. 8 and 9 give electron-microscopic pictures of slip lines of crystals elongated by 0.07 and 1.1 pet, respectively. For crystals with the orientation 1, see Fig. 6, only the two main slip systems (101)[111] and (110)[111] were found. With the crystals of group 2 the two main slip systems are again evident, with

Jan 1, 1965

By Willard P. Ward

The numerous direct processes which have been patented and brought before the iron-masters of the world, differ materially from that now introduced by Mr. Wilson. After a careful examination of his process, I am convinced that Mr. Wilson has succeeded in producing good blooms from iron-ore, and I think that I am able to point out theoretically the chief reasons of the success of his method. Without going deeply into the history of the metal, I may mention the well-known fact, that wrought-iron was extensively used in almost all quarters of the globe, before pig or cast-iron was ever produced. Without entering into the details of the processes by which this wrought-iron was made, it suffices for my present purpose to say that they were crude, wasteful, and expensive, so that they can IE employed to-day only in a very few localities favored with good and cheap ore, fuel, and labor. The constructiou of larger furnaces and the employment of higher temperatures led to the production of a highly carbonized, fusible metal, without any special design on the part of the manufacturers in producing it. This pig-iron, however, could be used only for a few purposes for which metallie iron was needed; but it was produced cheaply and with little loss of metal, and the attempt to decarbonize this product and bring it into a state in which it could be hammered and welded was soon successfully made. This process of decarbonizatioa, or some modification of it, has successfully held the field against all, so-called, direct processes up to the present time. Why ? Because the old-fashioned bloomeries and Catalan forges could produce blooms only at a high cost, and because the new processes introduced failed to turn out good blooms. Those produced were invariably "red-short," that is, they contained unreduced oxide of iron, which prevented the contact of the metallic particles, and rendered the welding together of these particles to form a solid bloom impossible. The process of puddling cast-iron, and transforming it by decarhonization into wrought-iron has, as everybody knows, been in successful practical operation for many years, and the direct process referred to so closely resembles this, that a short description of the theory of puddling is not out of place here.

Jan 1, 1884