Search Documents

By W. T. Bell, M. P. Lebourg

The perforating of multiple tubingless completions, in which two or more strings of 27/8-in. OD casing are installed in the same borehole, presents two basic problems. First, good completion practices require an eficient perforator that leaves no debris to interfere with subsequent completion operations. Second, and of more complicated nature, a system is needed for controlling the direction of fire so that adjacent strings are not damaged. Development of of a 2-in. OD, steel retrievable, shnped-charge gun has solved the first problem. The second was resolved through development of three different devices to provide directional perforating for the two types of completion methods being employed today. These include a mechanical orienting device and two self-orienting radiation devices. Conceivably, the latter methods could be adapted to the directional perforating (of .upper zones) of conventional dual and triple completions without removing production tubing and packers. INTRODUCTION The recent trend to multiple tubingless completions,' wherein two or more strings of 27/8-in. OD casing are installed in the same borehole, has presented two basic perforating problems. The first problem to be overcome was the design of a gun that would result in efficient perforations without causing debris to bridge in these small-diameter casings. The second problem was, of course, to devise a system for controlling the direction of fire such that adjacent strings would not be damaged. The problem of gun debris in slim-casing completions has been well defined in the numerous 27/8-in. single tubingless completions which have been effected during recent years with the expendable-type perforators. Failure of expendable-gun debris to settle out properly, even with good gun break-up, has resulted in bridging inside these small-diameter casings. This, in turn, has interfered with completion and re-conditioning operations. The past two years have clearly shown, in fact, that debris problems are not confined to this small range of casing with most designs of expendable-type guns. A high incidence of bridging has even been reported in 4%-in. OD casing. The perforating of multiple tubingless completions has entailed, therefore, the development of a completely debris-free gun of adequate performance, as well as the necessary devices to provide positive directional perforating in the two completion methods presently being employed. THE GUN —DESIGN CONSIDERATIONS The design of a shaped-charge gun for slim-casing perforating has presented a maze of interrelated prob-lems. Since the primary specification has been leveled at efficient charge performance with complete elimination of gun debris, it has been necessary to develop a retrievable steel-carrier gun of tubular construction to house the charges. The carrier must be retrievable through 2.29-in. API pump-seating nipples which are usually installed in 2 7/8-in. strings. To provide for recovery of the gun from the well, swelling of the carrier on firing must be carefully controlled. Control of swelling automatically means control of explosive weight in the shaped charge which, in turn, influences charge performance. Carrier swelling also depends upon the confinement pressure at the level being perforated, which imposes a hydrostatic pressure-depth limitation. Burr interference on the wall of the carrier, resulting from passage of the jet through the carrier wall, must be eliminated by suitable design. Clearly then, a satisfactory shaped-charge gun design for slim-casing operations represents a fine balance between carrier swelling, hydrostatic pressure, explosive weight and charge performance. Additionally, to lend itself to directional perforating, the gun design must provide a positive locking mechanism for individual charges within the gun carrier. This fixes charge orientation within the carrier and prevents

By Tim O’Neil

Tire companies have historically used the mining industry as a platform to launch new technologies. And the mining industry has been receptive to that. So, while developing its Two Piece Assembly, Goodyear noted a number of trends in the mining industry: •The global market sophistication of equipment and operations requires the packaging of products and services to provide the best return on investment. •Industry consolidation and growth have resulted in fewer, more powerful mining houses, leveraging purchasing power in the marketplace. •User productivity demands continue to drive original equipment manufacturers to develop higher pay-load equipment. •Technology needs include improved ergonomics, to reduce fatigue and increase operator productivity. •Increased laws and environmental regulation prohibit on-site whole tire disposal practices.

Jan 1, 2003

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Also included are tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1988

TABAKOTO / SEGALA ? Annual gold production approximately 100,000 oz ? Debt free ? Unhedged ? Combined surface reserves 949,000 oz ? Combined 9 year life Tabakoto open pit reserve 568,000 oz (3.4m tonnes @ 5.26 g/t Au) Segala open pit reserve 381,000 oz (3.98m tonnes @ 2.98 g/t Au)

May 1, 2006

By K. G. Matshika

"Nickel electroplating from sulphate electrolyte is an efficient process. To achieve good quality cathode, however, parameters such as temperature, nickel concentration, pH, electrode alignment, electrolyte flowrate and additives must be optimised, because these affect cathode morphology and current efficiency. It is also important to control the clarity and contamination of the electrolyte, as these have a considerable effect on the quality of the cathode surface. Delamination, surface roughness and pitting on the cathode surface can be caused by incorporation of solid particles or impurities form the electrolyte. Three types of solid particles were investigated: cuprous selenide, barium/ lead sulphate (co-precipitated) and ferric hydroxide. These particles can be found in industrial electrolytes, especially if there is a problem with the filtration step or contaminants have reacted to form insoluble particles. A rotating cylinder Hull cell was used for this investigation. It is found that the effects on morphology depend on the type of solid, concentration, particle size, current density and electrolyte flowrate. Cuprous selenide is the most detrimental, especially at higher concentrations, higher current densities and low flowrates. Increased rotational speed offers a uniform sheet of fine gas bubbles across the surface of the cathode which reduces the thickness of the diffusion layer of liquid adjacent to the cathode and increases the rate of mass transport to the cathode from the bulk liquid. INTRODUCTION Electrowinning operations are important when recovering associated by-products of nickel production, such as copper, cobalt and zinc, from pressure leach solutions. The base metal mineralization associated with platinum-group metal (PGM) production yields significant quantities of copper and nickel as by-products. The base metal refinery is vital in PGM processing as it increases the PGM concentration from mined ore by a factor of 400, in comparison with concentration by flotation (20 times) and pyrometallurgical processing (20 times) (Crundwell et al., 2011). Anglo American Platinum Ltd produces nickel cathodes by electrowinning and purges sodium from the base metal refinery in the form of sodium sulphate at the Rustenburg Base Metals Refinery (RBMR), as shown in Figure 1. This is the Sherritt acid leach process used in most base metal refineries to ensure no loss of PGMs and shows the subsequent purification steps for copper and nickel. Other refineries in Zimbabwe, such as Bindura and Empress, use the Outokumpu leach process (Pavlides, 2001)."

Jan 1, 2015

By G A. Wellwood

What do all iron ore mines have in common? Perfect production days! Yes, those harmonious 24-hour periods when the stars align and the daily output number rockets past the long-term average to hit new heights. While perfect days are always welcome, the focusing question iswas that just a ‘flash in the pan’ (due to a special cause) or an indication of the process’s capability (with clues to the common causes) which, if addressed, could make every day perfect? In the context of today’s operating environment, with the need to maximise productivity at minimum cost, it’s an important question.Investigations reveal that the throughput difference between a perfect production day and the average is often in the order of 40 per cent, and that bulk solids handling (BSH) system deficiencies are the largest (>50 per cent) class of lost opportunity. Root causes for underperformance of elements in BSH systems can often be traced back to the detailed design and even study-stage oversights. Essentially baked into the fabricated plant, operations are effectively forced to accept them at the point of practical completion and then deal with the consequences for the life of the mine. Subsequent normalisation of these defects in the planning process reduces visibility and hence the impetus for long-term solutions in favour of lower targets and quick fixes to keep the show on the road. On an industry wide basis the design processes and assumptions responsible for BSH system underperformance become enshrined as common practice and hence repeated across sites and organisations.In addition to making the case for action, practical steps that can be taken to help realise the significant productivity prize and avoid the problems in first place are provided.CITATION:Wellwood, G A, 2017. One perfect (production) day – a bulk solids handling perspective, in Proceedings Iron Ore 2017, pp 443–452 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Michael J. Cruickshank

A workshop to examine recovery systems for selected strategic and critical materials in the U.S. National Seabeds for the National Defense Stockpile in the 21st Century was held in Hawaii September 26-28, 1991, sponsored by the National Science Foundation and the Marine Mineral s Technology Center. The National Defense Stockpile of critical and strategic mineral commodities is presently in a deficit position of more than 7.5 billion dollars. Current domestic reserves of some commodities are limited or nonexistent. As defined by the U.S. Bureau of Mines, "Reserves are select resources . . . which at the time of classification, can be mined at a profit." Occurrences of these minerals have been discovered offshore within U.S. jurisdiction. If the technology could be developed to convert these resources into usable ore reserves, our dependence on foreign ores could be greatly reduced. Preliminary estimates indicate that a ten-year program of ore reserves definition, with appropriate technical developments to demonstrate a recovery system, could cost less than half the amount authorized for stockpile acquisition in FY 1989 alone.

Jan 1, 1991

By Eric L. Trist

The objective of this contract was to review the results of the Rushton Mining experiment in work organization and design, to explore the extension of knowledge gained from Rushton to other underground coal mines, and to conduct a search for a potential mine site for a demonstration project. The primary focus of the contract was on a search process to provide the research team with the opportunity to evaluate the different potential experimental sites, in order to select one or more with the highest potential for success. This search process also provides the various levels of union and company officials the opportunity to fully understand the context of the research before making a decision on whether to participate. While the search project failed in its attempt to locate a specific mine site, the research team believes that this is not a rejection of the actual project but rather extreme caution because of the uncertainty within the UMWA.

Jan 1, 1978

By Marcos Villegas

El presente texto describe el desarrollo del sistema de gestión de riesgos en la reingeniería de procesos, justificando la inversión en gestión de riesgos de la concentradora Atacocha donde se protege a las personas, activos e ingresos, minimizando el potencial de pérdida de los riesgos y así proveer fondos para recuperar las posibles perdidas y soportar el sistema en salud, seguridad, medio ambiente y Calidad (SSMAC).

Sep 9, 2007

By R. Karl Zipf, Francois E. Heuze

Stress analysis programs such as MULSIM/NL, LAMODEL, MinSim 2000, and EXAMINETAB are used in the mining industry to analyze stresses and displacements in coal mines, platinum mines, gold reefs, and tabular-type deposits. These relatively simple numerical models can efficiently simulate yielding and failure of a rock mass near a mine opening and subsequent stress transfer. The main input parameters for these models are a family of nonlinear stress-strain curves for the in-seam material. For many applications of these models, such as in coal mining, extensive field measurements and observations exist from which to estimate these stress-strain curves and calibrate the numerical models; however, such measurements are lacking for other types of mines. A three-step method is presented to determine nonlinear stress-strain curves for boundary-element (BE) programs used in many mining applications. The method requires a suite of laboratory-scale strength tests at various confining pressures. Note that this analysis uses laboratory-measured strength and modulus properties of alluvium. The dependency of the mechanical properties of alluvium on scale has not been established, although more tests are being planned. However, it is believed that the relative comparisons performed are valuable regardless of scale effects. First, the FLAC2D computer program is used to model the laboratory tests and determine cohesion (c) and friction angle () for a Mohr-Coulomb material model. Second, another FLAC2D model uses the c and values to calculate vertical stress and strain around a single opening in the rock mass. This model calculates the stress-strain path of points at various distances from the opening boundary. Finally, based on these stress-strain paths, the stress-strain curves needed for a BE analysis are derived. This three-step method was demonstrated in a large, flat-lying underground test facility in very weak rock. The BE analyses agreed well with observations of failure at the test facility and provided a basis for evaluating the behavior of alternative layouts.

By M. R. Tek, L. K. Thomas, D. L. Katz

Threshold displacement pressures are needed to determine how much overpressure can be used in storing natural gas. An experimental technique for determining threshold pressures by displacing water with gas from samples saturated with water is presented. Threshold pressures for eight low permeability samples were measured. Threshold pressure data obtained in this work, plus data on higher permeability samples reported in the literature, are correlated with porosity, permeability, surface tension and formation resistivity factor. Mercury injection pressures also were measured and correlated with air-water threshold pressures. Threshold pressures were found to be independent of time. An aerial photograph of gas emerging from the top of a core shortly alter its threshold pressure has been exceeded shows that the gas bubbles are uniformly distributed across the face of the core. Channeling will occur, however, when an increased gas phase permeability is reached, A porous medium can be re resealed alter its threshold pressure has been reached, provided it has not been desaturated below a fixed saturation. Its new threshold pressure will be lower than when the sample is 100 percent saturated with water. INTRODUCTION The degree of overpressure in excess of the discovery pressure that a gas storage reservoir can withstand is determined by the ability of its caprock to contain gas, providing the pressure does not exceed the structural limit of the reservoir. The retention of gas in a reservoir by a caprock saturated with water is a result of the capillary forces acting at the gas water interface. Without the presence of water in a caprock, gas would leak out of the reservoir at a rate determined by the permeability of the caprock to gas. The ability of a caprock to contain gas is expressed in terms of its threshold displacement pressure, which is defined as the minimum pressure needed to initiate the displacement of a wetting phase by a nonwetting phase from a porous medium 100 percent saturated with the wetting phase. The gas industry must be able to predict how much "overpressure" a gas reservoir can withstand before leakage occurs by gas displacing water from caprock overlying the reservoir. This is of economic importance since the storage capacity of a gas reservoir is proportional to its pressure. The discovery pressure for most reservoirs is found between the upper and lower limits1 shown in Fig. 1. Discovery pressures in excess of their hydraulic pressure gradient are attributed to the compaction of an isolated shale formation by the overburden.2.3 The lower limit of 0.433 psi/ft corresponds to the weight of the overburden, the gradient of the rock itself. Somewhere between

Jan 1, 1969

By Tano Balbin, Valery Astakhov, Juha Timperi, Lauri Koresaar

"Online elemental analysis is the basis of optimal flotation control in mineral concentrator plants. Traditionally XRF analyzers have been used as the online analysis method. However, online XRF analyzers struggle to measure elements below calcium in atomic number (Z=20). For many processes lighter element assays would be beneficial to improve control of grade and recovery. Processes where elements below Ca are required include P, Mg and Si in phosphate concentrators, Si, Mg and Al in iron concentrators, and S and C in gold concentrators. Laser-Induced Breakdown Spectroscopy (LIBS) based elemental analysis can readily be applied to these processes. LIBS is based on generating plasma in the slurry sample by a high energy laser and analysis of the plasma by optical emission spectroscopy. Capabilities of a new Courier® 8 analyzer based in LIBS technology are demonstrated for elemental analysis starting from lithium (Z=3). Results of a plant installation in a sulfide gold concentrator provide a good agreement with the analyzer and laboratory assays.IntroductionEffective process control can be regarded as one of the fastest paying investments for a mineral processing plant. Process optimization in flotation circuits requires constant feedback of the process state. If only manual laboratory samples are available, this optimization becomes difficult due to the long delay between taking the sample and acquiring the laboratory result. If the element grades are available in online basis, the operator or automatic process control system can make corrective actions in real time.Online X-Ray Fluorescence (XRF) analyzers have been in use at concentrators for decades. The XRF analyzers can provide a fast, accurate and precise analysis from slurry streams. However, the drawback of XRF analyzers is their lack of capability to measure elements below Ca (Z=20) in atomic number. The low energy X-rays of the low atomic number elements get absorbed by water in the sample, protective window of the analyzer, or air between the sample and spectrometer."

Jan 1, 2017

By Rob Jameson

"The demand for commercial and residential construction has continued to evolve across the United States over the last decade. Our markets demand larger, deeper and inherently more complex structures, located within increasingly constrained urban locations and with challenging geotechnical conditions. As project demands incrementally escalate, specialty contractors are continuously challenged to extend their state of practice. Development in the size and capabilities of construction equipment, tooling, techniques, monitoring and verification systems over the last decade has consistently allowed contractors to build larger and deeper. For support of excavation (SOE), in addition to scale, selection of the most appropriate system has been a key to success in the most challenging ground conditions. This selection process is based on sound engineering and construction practice, and also prior experience, both positive and negative. Ultimately many Owners have chosen to manage their risk of SOE construction through design-build contracts, which allows specialty constructors to optimize the balance of cost, schedule, scope and associated risk based on their local expertise. Successful implementation of a design-build methodology begins long before a contractor is selected, with identification of key project requirements and risk factors during the feasibility studies and design development phases. In these early stages of the project development, advice and budgets are frequently solicited from Specialty Contractors. The Owner, Construction Manager and Consulting Team will filter this input from multiple sources to provide their specific recommendations, develop construction documents and select the appropriate form of contracting. Only in the final stages, after award of a Design-Build Subcontract, can the successful specialty contractor directly influence risk management approach on the project. A case study is presented from Block 9 in San Francisco’s Transbay District. This project demonstrates the incremental identification, assignment and mitigation of construction risk through the planning and design build process for SOE on the deepest planned excavation in San Francisco.INTRODUCTIONThe mature urban development market in United States results in high demand for complex Support of Excavation (SOE) schemes on constrained sites. The Design-Build approach can be applied to increasingly difficult SOE challenges, combining regional specialty subcontractor knowledge and experience in order to optimize solutions for cost and schedule. The most successful applications will involve early engagement of shoring subcontractors within the project teams, during feasibility and design development stages, in order to identify key scope and risk issues, and their potential solutions. Throughout the project development, it is important to reasonably assign responsibility for construction risks amongst the project stakeholders who are best able to control them.This paper presents a case history for San Francisco’s Block 9, a well-planned and successfully executed design-build SOE project in San Francisco’s Transbay Redevelopment area. Throughout the 4 year period from the Developers initial proposal to the Redevelopment agency, through completion of excavation down to subgrade, the project team developed a series of increasingly refined SOE schemes, with corresponding scope definition and cost and schedule estimates. This program relied on early identification of key challenges and risks for the project, and evolved through multiple phases of proposals as first the General Contractor (GC) and then Specialty Shoring Subcontractor were engaged for the project. The scheme, cost and schedule refinements continued throughout construction in order to accommodate unanticipated conditions and events as they unfolded."

Jan 1, 2017

By A. T. Jakubick, A. MacG. Robertson

This paper reviews key issues related to the placement of dry (soil) covers on extremely weak, compressible fine tailings. The design and construction of soil covers on such tailings often presents a formidable challenge to the geotechnical as well as the environmental engineer due to the low shear strength, poor traffic ability, and high settlement of under consolidated tailings at the time of reclamation. The geotechnical issues to be considered include: (1) consolidation of near-surface tailings to achieve strength gains, improve traffic ability, and allow safe placement of initial cover layer; (2) stability of tailings slopes during dewatering of tailings ponds and/or cover placement; and (3) long-term settlement of tailings and its impact on cover integrity and final surface shaping. The environmental issues to be considered include: (1) management of contaminated (free) pond water; (2) management of contaminated pore water expelled during tailings consolidation; and (3) management of (uncontaminated) surface water on top of the cover. This paper summarizes recent experiences gained in a large uranium tailings reclamation project. It is concluded that a careful consideration of both geotechnical and environmental issues during the planning stages greatly reduces the costs and environmental risks associated with fine tailings reclamation.

Jan 1, 2000

By Don Hickey

The MTA in conjunction with LIRR, are in the process of expanding one of the largest commuter railroads in the country, with over 260,000 passengers a day. The LIRR, which provides 700 passenger trains every 24 hours, can?t continue on the present growth course as a joint tenant in Penn Station with Amtrak and NJT. For this reason, in conjunction with the fact that over 53% of LIRR?s current riders into Penn Station are ultimately bound for the East Side of Manhattan opening, have created the need for the expansion of the LIRR. The complete expansion will cost approximately 6.3 billion dollars and all of the contracts are to be completed by 2013.

By Edwin E. Maust

In response to the ever- increasing demand for high temperature materials, the Bureau of Mines instituted a program for the study and development of superrefractories, One of the major tools obtained for use in this research was an image furnace of the double-paraboloidal mirror type. Although extensive theoretical analyses of solar furnace performance may be found in the literature, comparable detailed information on the double-paraboloidal-mirror image furnace has been nonexistent. This report presents an analysis based on an investigation undertaken to ascertain the limitations and characteristics of the furnace so that it can be used most effectively. The quantitative determination of the energy available at the image, the control of this energy by mans of a 60-inch iris diaphragm, and its variation with position and time relative to the heat source used have all been dealt with in detail. The quantitative results were obtained using a specially designed waterflow calorimeter and these measurements, in conjunction with the theoretical analysis, are used to present a fairly complete description of the furnace and its capabilities.

Jan 1, 1962

By M. S. Raseroka

An experimental rig has been constructed to produce chloride stress corrosion cracks in Type 304L stainless steel tube samples. The samples are to be used to test possible in situ repair methods in future work. The factor which influences the time to failure most strongly is the sample temperature; the distribution of cracks within the sample is affected by local temperature variations and by the position of the water line. Low-frequency oscillations in stress, caused by the on-off temperature controller, did not appear to influence cracking in these tests.

Jan 1, 2009

By Jerome Apt

This report presents the methods and results performed pursuant to the U. S. Bureau of Mines contract entitled "Noise Abatement in Mining Machinery," Number H0122054. 2.1 Background Until the Congress of the United States created and passed Public Law 91-173, the Federal Coal Mine Health and Safety Act of 1969, there were no directly-applicable standards for noise exposure for underground coal miners.1 Section 206 of this law, approved December 30, 1969, provided for standards of noise to be applicable to each coal mine. It is as follows:

Jan 1, 1975

By Wilson G. L, Lord J. H

A detailed analysis of faulting indicatcs that blocks of "greenstone" have been thrust beneath the southern end of the Mt. Isa orebodies.This "greenstone" basement is considered to be a major structural control in the localization of these orebodies.INTRODUCTIONThis paper is based on exploration carried out by Mining Corporation (Aust.) N.L. from 1956 to 1960 in the area immediately south of Mt. Isa, Queensland. During this period over 20,000 ft of diamond drilling was completed together with costeaning and geochemical exploration.Early in 1959, it became apparent that diamond drill information could not be correlated with the current geological concepts of this area and a detailed geological appraisal became necessary. In all, sixty square miles were mapped at a scale of 1 in. to 500 ft, using enlarged aerial photographs. All drill core was logged and sections re-interpreted.Professor K. C. Dunham of the University of Durham consulted on this project and contributed through valuable discussion. Dr. A. Day of the University of Sydney carried out a gravity survey in February 1960 and Dr. H. Wilshire of the same University undertook microscopic examination of rocks from the area. Certain sections of the area were investigated geochemically by Mr. K. K. Hughes of New Consolidated Gold Fields (Asia) Pty. Limited in 1960.In outlining a theory of ore genesis in the area the writers have drawn heavily on the invaluable data published by many previous workers on the Mt. Isa field, in particular...

Jan 1, 1963

By Edwards A. B

The occurrence of lollingite (FeAs2 ) in the Broken Hill lode is recorded by an analysis of lollingite published in the Annual Report of the Department of Mines, New South Wales, for the year 1934 (p. 69). The analysed specimen came from the North Broken Hill mine, and material from the same occurrence (Specimeh No. 1), as well as two specimens (Nos. 3 and 4) from the Zinc Corporation mine, have been forwarded· to us by Mr. M. Mawby of the Zinc Corporation Mine. This material has been supplemented by another specimen (No. 2) from the Zinc Corporation mine, passed over to us by Dr. I. Wark.The original analysis of lollingite is quoted in Table I, and shows that the Broken Hill lollingite contains appreciable amounts of cobalt and nickel, and, indicates that the iron is to a considerable extent replaced by cobalt and nickel, so that its formula should be written (FeCoNi) As2This is supported by a microscopical examination of a polished surface of the lollingite, in which no individual arsenides of cobalt and nickel can be detected.Coarse grained galena, sphalerite, chalcopyrite, and pyrite are attached to our specimen of lollingite from the North mine, and are separated by a sharp junction from a mass of lollingite associated with some arsenopyrite and garnet. The massive lollingite can be distinguished from arsenopyrite in the hand specimen by a much brighter, silvery lustre, against which arsenopyrite appears a dull silver grey; but the passage from lollingite to arsenopyrite appears transitional.

Jan 1, 1939