Search Documents

By B. J. Schat, A. W. O. Bots, O. S. Langhorst

Amsterdam City Council is building a new metro line, the North–South Line. The line passes under Amsterdam Central Station (a listed building) about 18m below street level. The retaining wall that has to be built underneath the existing building is an innovative construction consisting of two rows of steel piles interspersed with a solid mass of overlapping jet grout columns: a composite ‘sandwich’ wall. This paper gives an overview of the approach taken to designing (computational models) and building the retaining wall. Special attention is paid to the observational method used for the construction of the jet grout columns.

Jan 1, 2007

By R G. Barker, A B. Christie

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. More than 11 Moz of Au and 50 Moz of Ag have been produced from epithermal deposits in New Zealand, almost entirely from 50 deposits in the Hauraki goldfield. Since the 1980s, new deposits have been discovered at Waihi (Favona, Trio, Correnso) and nearby at Golden Cross. Feasibility studies into reopening the Talisman mine at Karangahake are continuing, and advanced projects with preliminary inferred resource estimates are reported at Wharekirauponga, Neavesville and Muirs. In the Taupo Volcanic Zone, 11 prospects have been drilled, resulting in the definition of large but low-grade Au-Ag resources at Ohakuri. In Northland, several Au, Ag and/or Hg prospects are known, and small quantities of Ag and Hg have been mined. Six prospects have had some drilling, with the most advanced exploration at Puhipuhi. The application of Taupo Volcanic Zone geothermal systems research to the modelling of former hydrothermal mineralising processes in some epithermal prospects has enabled better targeting of exploration.CITATION:Christie, A B and Barker, R G, 2015. Exploration for epithermal gold deposits in New Zealand, in Proceedings PACRIM 2015 Congress, pp 533–540 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Paul C. Schmall, Arthur B. Corwin, Derek Maishman

Ground freezing occupies a unique and important niche in underground construction, fulfilling a geotechnical need that is difficult, or sometimes impossible, to fulfill through other groundwater control and excavation support methods. Where complete groundwater cut-off and in-built ground support are required, and deep excavation is planned or the work occurs in difficult or disturbed ground, ground freezing offers the assurance critical to safe and timely construction. Compared with other groundwater cut-off or excavation support methods, a frozen wall is easily connected to underlying bedrock and will also adhere to adjoining subsurface installations or obstructions, if necessary, to provide a composite cutoff structure. Ground freezing is effective in all soil and ground conditions and has been used for emergency situations in disturbed, displaced or loose ground, where detailed soil characterization could not practically be performed.

Jan 1, 2005

By P. B. Kelleher

Most of the piers and other pile-supported marine structures in the New York City Harbor area were constructed prior to the widespread use of currently available pile protective systems. As a result, the support piling of many existing marine structures have experienced deterioration to an extent that their structural sufficiency is impaired long before the useful life of the structures they support is over. This situation presents special and unique problems of how to restore the structural integrity of these piles while at the same time allowing full use of the structures they support. Spearin, Preston & Burrows is a 100 year old New York City-based marine construction firm specializing in waterfront and foundation construction. In recent years it has undertaken and successfully completed several unusual projects in the New York City Harbor area involving the rehabilitation of existing, deteriorated piling underneath major, economically important marine structures. This work was accomplished using techniques that permitted full use of these structures. Several different pile rehabilitation systems were used, each having their own particular application to the deterioration problems of the piles supporting each structure.

Jan 1, 1989

By P. J. Rider

Diamond Value Management?s objective is to achieve $/ton revenue improvement across De Beers group mines. The respective %improvement contributions are measured against targets set by each of the operations. Degree of target achievement is measured via a maturity model at each operation. DVM comprises seven elements. It spans several value chain facets and various collaborative projects are conducted under its umbrella. New technologies in De Beers are also evaluated from a DVM perspective.

Jan 1, 2003

By Sikko Doornbos

For the extension of the Paper Mill of Parenco in Renkum, the Netherlands, the application of a pile foundation was required. The demands for this pile foundation were very explicit a vibration free and soil displacing pile systems with low allowable settlement. Another important aspect was the total amount of piles (originally over 1600 auger piles) which had to be executed within 3 months, in very difficult and unhomogeneous soil. Based upon these conditions the Tubex Grout Injection Pile was chosen to be used for this project. This system involves the drilling of a steel tube with a conical pile shoe while grout is injected at the point simultaneously, creating a mixed-in-place layer around the tube. INTRODUCTION After extensive marketing, the board of directors of Parenco, decided to a large extension of the production capacity of its paper mill by building a new production building called Paper Mill 1 or PM-1. The new PM-1 extension had to be constructed beside the existing PM-2 because of limited terrain. The site is located right between the Rhine river and Renkum, approximately 15 kilometers (10 miles) west from Arnhem (see figure 1). The construction involved the building of the PM-1 extension of approximately 250 meters (820 ft.) long by 40-60 metres wide (130-200 ft.). The main structure was to be constructed of precast concrete beams and columns.

Jan 1, 1987

By Robert H. Lambeth

There are no identified mineral resources in the Italian Peak RARE II areas, and there are no producing or developing mines within or adjacent to the study area. Several prospects are in RARE II area M-4945, Idaho, but none were found in the area I-1945, Montana. The Viola Mine (fig. 1, no. 15) vicinity and the Heart Mountain vicinity along the west and south borders, respectively, are being prospected. There has been no recorded production from mines within the study area, but between $2.5 million and $5.0 million worth of lead, silver, and zinc were produced in the adjacent Birch Creek district - dominantly from the Viola Mine - from 1882 to 1889 (Anderson and Wagner, 1944, p. 14). The Viola and other mines in that district are possibly, on basin-margin, carbonate-hosted, lead-silver-zinc deposits stratabound within the Devonian Jefferson Formation. Previous studies have considered them to be hydrothermal, replacement orebodies. Mineral occurrences in the Heart Mountain area are possibly black-shale hosted uranium-vanadium deposits in the Mississippian-Devonian McGowan Creek Formation or perhaps the underlying Devonian Three Forks Formation. The Jefferson and McGowan Creek Formations underlie many scattered segments of the study area. The deposits and occurrence; are not sufficiently exposed to determine tonnage and grade, but sampling indicated moderate resource potential at two properties just outside the study area, the Viola Mine and the Elkhorn Group (fig. 1, no. 33). Local residents indicated there are several thousand tons of zinc-bearing resource; at the Viola line. A 23-ft (70-m) drill hole intercept near Heart Mountain et the Elkhorn Group adjacent to the stuny area contained 0.15 percent uranium oxide

Jan 1, 1983

By Nick Barton

When the Q-system was launched in 1974, the name referred to rock mass classification, with focus on tunnel and cavern support selection. Besides empirical design of support, the Q-value, or its normalized value Qc, has been found to correlate with seismic P-wave velocity, with deformation modulus, and with deformation. The Q-system provides temporary or permanent support for road, rail, and mine roadway tunnels and for caverns for various uses. It also gives relative cost and time for tunnel construction for a complete range of rock qualities. There are also indications that Q has captured important elements of the cohesive and frictional strength of rock masses, with Qc resembling the product of rock mass cohesion and rock mass friction coefficient.

Jan 5, 2007

By Paul G. Marinos, Vassilis Marinos, Evert Hoek

The Geological Strength Index (GSI) is a system of rock mass characterization that has been developed in engineering rock mechanics to meet the need for reliable input data related to rock mass properties required as input for numerical analysis or closed-form solutions for designing tunnels, slopes, or foundations in rocks. The geological character of the rock material, together with the visual assessment of the mass it forms, is used as a direct input for the selection of parameters for predicting rock mass strength and deformability. This approach enables a rock mass to be considered as a mechanical continuum without losing the influence that geology has on its mechanical properties. It also provides a field method for characterizing difficult-to-describe rock masses. Recommendations on the use of GSI are given and, in addition, cases where the GSI is not applicable are discussed.

Jan 5, 2007

By Rudi Podjadtke

In a short chronological review the development concepts and improvements in steel roadway support are shown. The successful standardization concept of RAG Deutsche Steinkohle and currently used support systems are important topics. The history of optimizing the material properties for the steel arch support with different alloys up to the tempering used today is discussed. The present-day application of the steel support is additionally presented. Today, it represents a system component of modern roadway support also for highly stressed roadways. In addition to the yielding roadway arch support, this overall system - the combination support - consists of the additional components of a rockbolting system and concrete backfilling. The comparison of the application areas for each individual partial system with the overall system illustrates its high performance capability. Actual practical experience with the state of the art typed steel arches are pointed out exemplarily. Understanding the complete system permits the selection of the economically optimal support for all conditions.

Jan 1, 2008

By C. Maree

Paper written on project work carried out in partial fulfilment of B. Eng (Chem. Eng.) This paper describes the development and use of a process simulator to optimize gypsum recovery at Afmine, a small plant near Yzerfontein on the South African West Coast. The simulator consisted of models of the major plant equipment, viz. hydrocyclones, surge bins, settling tanks, a primary sieve and a dewatering screen. Experimental data suggested that the equipment could be modelled satisfactorily from data published in the open literature. Simulation studies have indicated that gypsum losses on the plant could be reduced substantially by means of some relatively minor modifications to the plant layout. Moreover, sensitivity analyses of the plant have indicated that optimization of the settling tanks should receive priority over the other process units.

Jan 1, 2005

By Z Li, A Fleming, S Webster, L Snyman

Northparkes Mines is developing the E26 Lift 1 North block cave mine, which is adjoined to the existing E26 cave. This paper presents the challenges and methods used to design the ground support system during the feasibility study. Calibrated numerical simulations were conducted to forecast the levels of rock mass damage and to assist the ground support design. Generally, low to moderate rock mass damage is forecast on the extraction and undercut levels. However, poor ground conditions are expected in sheared and preconditioned zones adjacent the existing E26 cave. This will result in difficult ground conditions during development, undercutting and drawbell establishment. Empirical assessments were conducted to make sure the ground support system is able to handle both the static and dynamic load demand, and to accommodate the deformation values. A safety factor of 1.5 was used for the designs to cover the unknown rock mass conditions and potential for larger seismic events. Learnings from the E26 Lift 1 and SLC, also mining against the E26 cave, are incorporated into the design. Fibrecrete, mesh and resin bolts / mechanical anchors are the primary ground support system used, and cable bolts for intersections with a span of more than 6 m. Following undercutting and during the operating life of the mine, secondary ground support and rehabilitation will be required.

Mar 15, 2021

By William E. Greenawalt

IN these days of special legislation for the benefit of various industries one might well consider one branch of human endeavor intimately associated with engineering-that of patents and patent litigation. It is estimated that 85 per cent of all industries in the United States are based directly or indirectly on patents. Most inventors are engineers, and most patent litigation pertains to the engineering industries. It is fitting, therefore, that engineers should be vitally interested in discussing patent affairs, particularly as inventors are not a professional group, and invention is mostly a transitory phase incident to the development of specific industrial problems.

Jan 1, 1937

By Allan F. Smith

The influence of hydraulic fluids on spontaneous heating in bituminous coals is determined by measurement of the temperature increases produced in coal-fluid mixtures heated to a temperature sufficient for the initiation of self-heating. Similar tests on as-received coal samples and water-coal mixtures are compared with the results obtained for the various hydraulic fluids. Three of the four coals were sampled from coalbeds known to have a history of spontaneous heating. The data provide a basis for predicting the possible effects in gob or carbonaceous refuse of coal mines.

Jan 1, 1963

By Paolo Heiniger

The aim of this paper is to present the operative solutions devised and then adopted to implement the underexcavation (soil extraction) of the Tower of Pisa, by means of soil extraction. The intervention has been performed by the Consorzio Progetto Torre di Pisa, a joint venture made of five qualified Italian companies (Trevi S.p.A. , Rodio S.p.A., Italsonda S.p.A., Ismes -Enel Hydro S.p.A., Bonifica S.p.A.), selected for their experience in the field of monitoring and restoration of monuments, structural design, foundation engineering and specialised works in underground conditions. Since 1991 the Consorzio has been charged with the specific task of implementing, within the contractual frame of a Concession, all the decisions made by the International Multidisciplinary Commission appointed by the Italian Government the previous year, with the aim at solving the «problem» of the Tower, strengthening the structure and stabilising its foundation. The Trevi Group, which is represented by Trevi S.p.A. in the above mentioned Consorzio, has given and is giving its direct and constant contribution and is engaged in supplying the special equipment to the operation and the drilling technology which has been successfully adopted to date.

Jan 1, 2000

By T. Khumalo, L. P. Coetzer

This paper addresses the impact of the variable speed drive on the particle size distribution in the product of a fully autogenous UG2 grinding circuit. It further discusses the impact of a varying particle size distribution in the product of the mill on the downstream classification and milling circuits. An industrial case study was used and data is presented to illustrate the techniques applied to identify the root cause of the shift in operational efficiency. The results achieved from both the investigation into the shift in plant efficiency and the sub-sequent corrective action taken illustrate that the root-cause methodology used in advance control can be effectively applied on production sites to both detect the shift and identify probable root-causes. The industrial example used confirms that the variable speed drive in a UG2 autogenous milling operation is a critical control parameter to ensure that the plant operates to design specifications.

Jan 1, 2006

By Lawrence J. Froisland

To aid in minimizing adverse environmental impacts of mining and mineral processing, the Bureau of Mines studied changes in soil characteristics in topsoil stockpiled during mining operations. Topsoil stockpiles in arid areas of New Mexico, Utah, and Wyoming were sampled over a 1- to 8-yr period to determine any changes in physical, chemical, or biological parameters in the top 15 ft of soil. Parameters examined in this study included soil moisture, pH, electrical conductivity, and cation exchange capacity; total nitrogen, organic carbon, carbon to nitrogen ratio, extractable potassium, and soluble phosphorus levels in the soil; general levels of bacteria activity in the soil; and productivity of the soil as measured by shoot yield in growth tests. Data were analyzed by multiple linear regression to determine possible effects of stockpile age and depth. Bacteria population counts, used as an indicator of goner l bacterial activity, was the only parameter found to be significantly correlated with stockpile age and depth at more than one site. Bacterial activity increased with depth at the two sites where it was measured. Activity increased with age at one site and decreased with age at the second. Significant changes in soil pH, electrical conductivity, and moisture were significantly correlated with stockpile age and depth at single sites. This study did not show significant, consistent deterioration in soil characteristics or growth yield of topsoil stored in stockpiles.

Jan 1, 1987

In 2004, a total of 741 nonmetal mining operations reported employment to the Mine Safety and Health Administration (MSHA). These mines (e.g., potash, gypsum, salt) comprised 5.1% of all operations.

Sep 1, 2007

By Norman O. Lotter, Dominic Fragomeni, Jorge Oliveira, Dee J. Bradshaw, Rebecca Monnapula

"The role of mixed collectors in enhancing the metallurgical performance of sulphide flotation processes was reviewed in 2008, and later published as an integrated theory by Lotter and Bradshaw, 2009. The theory proposed that xanthates, dithiophosphates and dithiocarbamates could be synergistically combined in an optimal formula to deliver improved grade and recovery. The approach uses a five-step structure, viz.1. A mineralogical study of the ore to be treated, identifying and quantifying the economic minerals (with hosting and association) and gangue species present.2. Selection of candidate collectors from this mineralogical information and from the known pulp conditions of that operation (e.g. Eh, pH).3. Design and execution of a factorial experiment to estimate and test the main effects and interactions, and to model the response surface for an optimum formulation [Box et al., 1978].4. Use of a High-Confidence Flotation Test platform in the factorial to reduce overall errors and allow for clearer observations [Lotter, 1995; Lotter and Fragomeni, 2010].5. Statistical design of a plant scale trial to measure and validate the gains [Napier-Munn, 1995; Lotter et al., 2009]. Eland Platinum, which was commissioned in November 2007, appointed a team to apply this theory to formulate an optimized mixed collector suite for use in the operation. The West Pit ore (UG2 - Normal ore) was sampled at site and brought to Xstrata Process Support, Sudbury, Canada, for mineralogical and metallurgical testing in 2008. Microprobe and QEMSCAN measurement characterized the type, grain size and textural association of the discrete Platinum Group Minerals (PGM) present. From the mineralogical data, it was clear that a mixture of dithiocarbamate and two xanthates would be a likely reagent suite selection. A factorially designed set of High-Confidence Flotation Tests studying these was performed, concluding that an optimal suite using certain amounts of these collectors was a viable formulation that would advance the grade and recovery performance at Eland above the standard PIBX by approximately 2.13% 4E PGE. The plant trial, which used a form of the replicated block design after Napier-Munn, 1995, and Lotter et al., 2009, exceeded this estimate with an overall PGE recovery gain of 2.48% (absolute basis) and a concentrate grade gain of 26.4 g/t PGE (absolute basis), as well as reducing chrome in concentrate from 2.04 to 1.62% (absolute basis). These gains proved to be statistically significant using the analysis of variance method, and have validated the theory."

Jan 1, 2011

By R. P. H. Willis

Uranium is back on the radar. Uranium has always been a controversial metal, from its role in the arms race to its claim to be the only viable alternative to fossil fuel. This paper will cover its properties and use, its occurrence and production in South Africa, the current market drivers and its future role as a primary energy fuel. It will highlight the difference between uranium used to make a bomb and uranium used in a power station. The recent significant uranium price rise will be put into context of the market drivers including geopolitical issues. Planned expansions in nuclear power station capacity will be reviewed, as will new mine production. Future demand will also be speculated on.

Jan 1, 2006