Search Documents

By Jason J. Crowder

Presentation Outline ? Introduction ? Costs of ground support and rehabilitation ? Why post-failure rock mass properties are necessary ? The Rock Mechanics Problem ? Present State of Modelling and Instrumentation in Mining ? Case Study Background ??Williams Mine ? Deriving Parameters for Modelling from Instrumentation ? Results from Case Study ??Back Analyses ? Discussion of Research Impact t Summary

May 1, 2006

By Travis Q. Lyday

During 1981, Ecuador's gross domestic product (GDP) increased by a reported 4.8% in real terms, a slight improvement over that of 1980. In current prices, the CDP in 1981 was estimated at $13.7 billion.2 The inflation rate increased to 15.6% according to official figures, above that of 1980. Ecuador's production of petroleum increased 3% in 1981 compared with that of 1980. The consortium of Corporación Estat al Petrolera Ecuatoriana (CEPE), the state oil company, and Texaco, Inc., produced almost 98% of the total from their Putumayo Basin operations in Oriente, the eastern jungle region. In sharp contrast, output from the Santa Elena Peninsula Fields, where oil was first produced commercially in 1921, continued to decline, producing only 510,000 barrels, a decrease of almost 8% compared with that of 1980.

Jan 1, 1983

By Brian Fulcher, Michael Bell, Shimi Tzobery, Werner Burger, John Bednarski

The Arrowhead Tunnels Project represents the final portion of a 70 km (44-mile) long water conveyance facility that will bring up to 28 m3/sec (1,000 ft3/sec) of water into Southern California. The 13 km (8-mile) tunneling project is well underway and consists of two, 5.8 m (19-foot) diameter TBM bores through extremely variable geological conditions. The tunnels lie near the base of the San Bernardino Mountains and several significant faults including the San Andreas Fault run within one kilometer (0.6 miles) of the tunnel alignment. Numerous other significant faults cross the tunnel alignment and water pressures in the tunnel have been recorded as high as 20 bar (300 psi). This paper describes some of the problems and challenges encountered and the solutions implemented to advance the two hybrid TBMs under conditions that ranged from hard rock with no water inflows to full-face granular material under 10-bar pressure and in excess of 32 l/sec (500 gpm) inflows. Due to the range and severity of ground and water conditions actually encountered, the Owner-Contractor-Designer team eventually found that adjusting the means and methods to be more responsive—virtually on a day-by-day basis—was needed to suit the conditions

Jan 1, 2007

By L. E. Fish, G. S. Wyman

CHUQUICAMATA open-pit mine is capable of producing a total of 105,000 tons daily. When the sulphide plant is operating to capacity the distribution of this quantity will be approximately 30,000 tons sulphide ore, 30,000 tons oxide ore and 45,000 tons of waste. At that time the combined capacity of the oxide and sulphide plants will be about 540 million lb of copper per year. Twenty one benches have been opened to date and all are still active except the three top ones at the northeastern limit of the pit. These have been pushed back to final slope line. The pit is 8850 ft long, 3540 ft wide and 980 ft deep. Benches are not all developed to a standard height as the large development shovels used in cutting new benches have been of different size and range. At this time new benches 521 ft high are being developed with an' 11-yd shovel. Ore haulage through the greater part of the pit operation has been on down grades to the crushing plant. With the opening of bench F-4 in April 1944 the first adverse-grade ore haul was encountered. Of the total tonnage now being mined, 35 pct comes from the four benches that are below the level of the crushing plant yard. Waste had been dumped on the same or nearly the same level as the bench from which it was removed up to the opening of bench F-4. Waste from this and lower levels is hauled to the level of the crusher, yard where it must cross the flow of ore traffic to reach the only available dumping space to the east of the mine. The average ore haul is 3.13 miles one way shovel to crusher, and the average waste haul from that portion handled by railroad is 3.32 miles one way from shovel to waste dump. Waste that is being removed by truck haulage from the upper part of the -mine is hauled an average of 1 mile. Ore loaded by trucks is hauled 3/4 mile to a car loading ramp and then by rail to the crushing plant. Drilling and Blasting There are two types of development for blasting being used: One for opening new benches and the other for bank shooting. The former consists of 9a in. diam churn-drill holes drilled 11.8 ft center to center in rows 10.2 ft apart with the holes staggered in the rows thus giving an equilateral-triangle pattern of 11.8 ft on a side. After the first block, 492 ft long by 71.5 ft wide, is shot in the pattern described above, the cut is advanced by smaller shots consisting of four rows of holes spaced 23 ft center to center with the rows 23 ft apart. These shots are fired in conjunction with side shots in which the holes are drilled 33 ft center to center and 29.5 ft back from the toe, thus squaring up the bank for subsequent shooting. An average bank shot consists of about 60 holes drilled in two rows parallel to the face, 30 holes to

Jan 1, 1952

By Wilson A. F

The use of stable isotopic measurements as a technique for elucidating the origin and history of the water in hydrothermal fluids is relatively new. Recept studies have emphasized the importance of meteoric water in the formation of many hydrothermal ore deposits including many epithermal gold-base metal deposits which occur in faulted volcanic terrane. Other vein-type gold ores are believed to have formed from fluids of magmatic or metamorphic origin and exhibit characteristic d18O values. Preliminary oxygen and carbon isotopic data for some important gold deposits of eastern Australia have emphasized the diverse origins of their ore fluids.The Mount Morgan gold-copper orebody is shown to be of the volcanogenic massive sulphide type with ore fluids predominantly of sea water origin. The Charters Towers fissure veins formed during hydrothermal activity associated with intrusion of Lolworth Igneous Complex equivalents. Oxygen isotopic studies of the quartz reefs at Stawell and Gympie have been inconclusive. The ore fluids have a d18O value of about 7 per mil and may be of magmatic or metamorphic derivation.

Jan 1, 1981

Probably no other country or coutinent has so many rich deposits of various different minerals as Australia. Long ago in the days of my boyhood in the old land the marvellous discoveries of high percentage copper at Burra Burra, Peak Downs, Yudanamutana, and other mines, was one of the principal themes of conversation in mining circles whilst the specimens of malachite, azurite, etc, brought home by returning miners were the admiration of my boyish eyes.Later on the WalIaroo and Moonta mines still further helped to heighten the reputation of Australia as a copper-producing country. During the 21 years that the writer has been resident in the Australian colonies, other mineral deposits have sprung into prominence, and with a Mount Bischoff for tin, a Broken Hill for silver and lead, and a Mount Morgan for gold, Australia can now boast that it has had within its borders the leading mines of the world, in four different minerals, and still at least maintains that pre-eminence in gold, silver and tin. To the miner from the old land, Australian mining is at first a revelation and a wonder. In very many instances he looks in vain for the regular strike and dip of the veins he has been accustomed to'Smooth hanging and foot alls are often wanting. 'Huge irregular deposits, like those mentioned above, viz., Burra Burra, Mount Bischoff, Broken Hill, and Mount Morgan, are mysteries that will take time to fathom-if, indeed, they are ever thoroughly understood and in many a smaller deposit there is much to interest alike the professor in the college and the miner in the mine.

By Prosser A. P

The conditions under which vanadium is rendered insoluble by silica in the alkali-roast process have been investigated starting with both slag and reagent-grade materials. The inert phase is a glass formed slowlyfrom soluble NaV03 produced at lower temperatures. It contains approximately 30 per cent V in a partly reduced state; iron is not a principal component. Some of the vanadium in the inert phase is slowly returned to a soluble form by heating in an oxidizing atmosphere below the temperature at which the glass is formed (750°C). As the reaction leading to the required, soluble form of vanadium is also slow between 600 and 750° optimization and control of the temperature profile and atmosphere in the furnace, and the residence time of the solids, are necessary to ensure high vanadium extraction during subsequent leaching.

Jan 1, 1976

By P. A. Davies

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 11pp., 15 refs. Hazards such as vibration, dust emission and fragment projection can result in an area called the Danger Zone being set around a blasting site. Traditionally Danger Zones have been set solely on the basis of consequences (e.g. based on the maximum distance of rock projection or expected ground vibration plus a defined safety margin). Advances in risk assessment and its growing acceptance as a safety management tool have led to the setting of Danger Zones based on both consequences and frequency of occurrence. This allows distances to be optimised on the basis of acceptable risk levels rather than the potential consequences of infrequent events. The setting of a flyrock Danger Zone is used to demonstrate a risk-based approach compared with a traditional consequence approach

Aug 1, 1995

By G. W. Luxbacher

This volume describes the use of the Penn State Mine Ventilation Simulator (PSU/MVS) to model existing mine ventilation systems and, in addition, to evaluate the effect of system modifications. Ventilation survey methods designed to insure computer input data of sufficient accuracy for simulation purposes are covered in comprehensive detail, including quantity and pressure measurement and fan performance testing. The development of input data from ventilation survey results is discussed and illustrated by the use of an actual field survey. Two programs, written in FORTRAN IV with WATFIV, are presented to calculate airway head losses from altimeter pressure measurements. An existing coal mine ventilation system is analyzed and modifications to the system are simulated and evaluated. In addition the application of the PSU/MVS to non-coal mines is briefly discussed. An extensive bibliography on ventilation surveying and simulation is included.

Jan 1, 1977

By R. Loots

High temperature creep resistant alloys are used in power plants as steam pipes and headers where they have to withstand super heated steam temperatures of up to 600ºC for the lifetime of the plant. Frequently certain portions of pipes may be subjected to excessive temperatures and consequently suffer from creep damage. Damaged portions then have to be replaced by welding new steel to the service exposed steel. Such welds will have to be subjected to a post weld heat treatment (PWHT) to relieve residual stress. During such a PWHT it is then possible for the steel to crack in the heat affected zone (HAZ) by what is known as Reheat Cracking (RHC), also known as stress relief cracking. For the present purpose the RHC susceptibility of service exposed steel was compared with that of new steel by reproducing the temperature cycle to which the HAZ will be subjected during welding in a weld simulator. This was followed by PWHT where the influence of residual stress was studied by applying a constant stress to such a weld-simulated specimen in a creep testing machine. A sharp spiral was machined along the length of the cylindrical specimen to simulate the presence of a possible weld defect. In this way it is possible to subject all portions of the simulated HAZ to the same stress intensity. For the purpose of the investigation 1/2Cr-1/2Mo-1/4V steel known to be susceptible to RHC was chosen. During testing a constant tensile stress was maintained while the temperature was increased to follow the thermal cycle prescribed for PWHT. It was found that the new steel in all instances failed by RHC along the grain boundaries in the high temperature heat affected zone. In the case of the service exposed steel the creep strength of parent metal was lower than that of new steel as a result of exposure to a steam temperature of 540°C for about 15 years. Consequently, all of the failures during testing occurred in a ductile manner by necking outside the HAZ rather than by RHC. When service exposed steel is welded to new material, it is expected that the creep strain associated with stress relaxation will mostly be concentrated in the parent steel outside the HAZ. Accordingly, it should probably not be necessary to make any extra allowance for reheat cracking during repair of steam pipes manufactured from 1/2Cr-1/2Mo-1/4V steel other than that applicable for welding new steel.

Jan 1, 2004

Leinster Nickel Operations, located in Western Australia, consists of an underground and three open pit mines in relatively adverse ground conditions. This paper reviews our ground control practices in the open pits, covering aspects of ground support, wall control and monitoring. These methods have been effective in allowing mining operations to continue beneath unstable slopes. In particular, the use of Ground probe?s slope stability radar has enabled the Harmony open pit to safely operate for months following indication of failure from traditional methods. This case study highlights the benefits of investing in appropriate slope stability monitoring systems.

Jan 1, 2006

By R. G. Cawthorn

The vertical distribution of platinum-group elements (PGE) in the Merensky and UG2 chromitite Reefs is highly variable, but does follow certain general patterns that allow the testing of geological models. In the Merensky reef, historically popular geological representations and interpretations have suggested that the mineralization occurs in a pegmatitic pyroxenite bounded by two chromitite layers. However, there are now enough published exceptions to this relationship to expose its fallacy. The vertical distribution of the PGE depends largely upon the separation between these two chromitite layers or the absence of one chromitite layer. Where separation is small or only one chromitite layer is present, there is considerable PGE mineralization in the footwall below the pyroxenite and lower chromitite layer. With increasing separation between the two chromitites, the mineral¬ization occurs progressively higher in the succession, and tends to track the upper chromitite layer. The view presented here is that the entire Merensky package is comprised of three events of magma emplacement, in which each has produced variable reaction with, and erosion of, the footwall, causing recrystallization of pyroxenite into pegmatitic pyroxenite. The magma then produced a chromitite layer followed by pyroxenite. Each chromitite layer is associated with some mineralization, which was extensively complemented by the subsequent formation of a sulphide liquid carrying PGE that trickled down through about 1 m of permeable crystal pile. The sulphide liquid formed after, not coincident with, the pyroxenite layers. The distribution of PGE in the UG2 chromitite shows up to three upward depletion sequences of PGE, also suggesting three events. The PGE are associated only with the chromite. The contribution from a sulphide liquid is considered to have been minimal for two reasons. Cu and Ni are extremely low in the UG2 which would not be expected if sulphides had been present. Also, by analogy with the Merensky, downward trickling of sulphides would have caused some PGE to be present in the footwall. There are some PGE in the footwall, but only where remnants of chromitite occur, and the hanging wall is lacking in PGE. In the northeastern Bushveld the UG2 chromitite is thinner than elsewhere, and there is a UG3 chromitite layer, not present elsewhere, that has a high Pt/Pd ratio. It is surmized that in the rest of the Bushveld the UG3 only appears to be absent because it has merged with the UG2 to produce the high Pt concentration at the top of the composite UG2. The non-accumulation of the package of pyroxenite-norite-anorthosite between the UG2 and UG3 in the northeastern Bushveld, which is not seen elsewhere, creates an interesting challenge to the formation of silicate layering in the complex. The mineralization in the Platreef is not addressed here. Keywords Bushveld complex, Merensky Reef, UG2 chromitite, geological evolution.

Jan 1, 2011

By J. T. Popp

This Bureau of Mines study reviews the geological factors that affect methane in the Beckley coalbed in southern West Virginia, including overburden, coalbed structure, type of and changes in lithology above and below the Beckley coalbed, and presence of fractures in the coal and rock adjacent to the Beckley. Depending on the depth, the Beckley coalbed emits from 216 to 520 ft3 of methane per ton of coal mined, and the Bureau estimates that methane emission in a deep, extensively developed mine in this area may exceed 3,000 ft3 per day per ton of coal mined. Average face cleat and butt cleat trends in the Beckley coalbed measured underground are N 33° W and N 53° E, respectively. Close cleat spacing con¬tributes to the friable nature of the Beckley and provides easy movement for methane and water. Because rider coals, splits, and carbonaceous shales may contribute methane to mine emissions, predictions of methane emission based on gas content of the Beckley coalbed alone may be conservative. Beckley coalbed reserves in the study area are 234 million tons. The gas content of the Beckley coalbed averages 407 ft3/ton, and the coalbed gas reserves are 108 billion ft3.

Jan 1, 1976

By William J. Campbell

Three types of X-ray analytical instrumentation were compared for applications in the secondary brass and bronze industry. The instruments were a conventional X-ray spectrograph, a portable X-ray spectrograph, and a radioiso-topic X-ray analyzer using balanced filters. The following two general applications were considered: Rapid identification for sorting scrap metals and quantitative analyses to provide guidance in the melting and casting of alloys. Twenty-three analyzed copper-base alloys were used as standards. Although the alloys varied widely in composition, matrix correction procedures were not necessary except for copper. The conventional X-ray spectrograph provides positive identification of the alloys and quantitative values for the six elements investigated--aluminum, copper, iron, lead, tin, and zinc. Equivalent results were obtained with the portable X-ray spectrograph for those elements whose characteristic X-rays are in the wavelength range of the instrument. The radioisotopic X-ray analyzer distinguishes certain groups of alloys and provides quantitative determinations for copper, lead, tin, and zinc. The sensitivity of the analyzer was marginal for the determination of small concentrations of elements of atomic number 26 or lower.

Jan 1, 1972

By Pierre De Pasquale, Aquilino Antonio Alvarez-Castro

Greenhouse gas emissions are now an essential issue for extractive industries. Actually, lowering of quarry energy consumption and CO2 emissions participates to answer both environmental and financial issues. The “EE-Quarry” European project, supported by the European Commission (EE stands for Energy Efficient), develops a new and highly effective modelling and monitoring Energy Management System technique to improve Energy Efficiency and move to a low CO2 emission rate in the nonmetallic mineral industry.

Jan 1, 2016

By J Addai-Mensah, M Adam, W Skinner, J Begelhole, K Quast

Granulation of iron ore fines into robust granules is critical to successful sintering and blast furnace operations in iron and steelmaking. Iron and steelmakers desire iron ore granules with high strength, uniform size distribution and low fuel consumption to enhance efficient sintering operation. Unlike hematite ore, magnetite concentrates do not granulate easily at low binder dosage to yield coarser granules due to the absence of nucleus particles. This motivates the present study to harness the complementary properties of hematite ore to enhance granulation of magnetite concentrates via blending. The current state-of-the-art in hematite and magnetite blend granulation is reviewed, along with granule property limitations. Preliminary experimental work on granulation of hematite and magnetite blends as a precursor to sintering is reported.CITATION:Adam, M, Addai-Mensah, J, Begelhole, J, Quast, K and Skinner, W, 2017. Enhancing magnetite concentrate granulation by blending with hematite ore, in Proceedings Iron Ore 2017, pp 17–24 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Yu Zhenquan

At the construction site of Bao Shan Iron &. Steel Mill in Shanghai, lots of RC driven piles with length of 50 to 60m were applied. The most unfavourable distribution of stress along the pile shaft was known by measuring the compressive and tensive stresses. With analysing the test results a phenomenon of impact fatigue of RC pile was discovered, the range of impact fatigue and its critical zone can be distinguished. Finally some countermeasures are presented to avoid the impact fatigue of RC long pile.

Jan 1, 1991

The sequences in alteration and mineralisation from five copper-gold porphyry systems (Taysan and Didipio, Philippines; Horse-Ivaal and Wafi River, PNG; and Goonumbla, Australia) and one gold-copper skarn system (Browns Creek, Australia) are documented in this paper. Alteration and mineralisation in all these systems reflect a common evolution from crystallisation of melts emplaced at shallow crustal levels (zoned potassic -> propylitic alteration), followed by exsolution of volatile-rich fluids from these melts (porphyry quartz ¦K-feldspar/biotite veins and local high temperature advanced argillic alteration), to a progressive cooling of the intrusion which results in associated retrograde alteration. Copper-gold mineralisation in all cases is almost exclusively restricted to the cooler retrograde events. The recognition of the temporal and spatial zonations in alteration and mineralisation in gold-copper porphyry systems has significant relevance in the interpretation of geophysical signatures, overprinting alteration, vein sequences and structural controls, and can lead to more focused and potentially more cost-effective exploration.

Jan 1, 1999

By Paramguru R. K, Jena P. K

Increasing demand for copper, lead and zinc with continuous depletion of good grade ore reserves, warrants the need for utilization of lean and complex ores of these metals. There is worldwide effort to develop suitable processes for these purposes. The present paper deals with the chloride leaching of complex base metal sulphide concentrates of two Indian deposits. A two stage leaching process is suggested keeping selectivity of metal dissolution in view.In the first stage most of the lead and zinc are reacted with dilute FeCI3 (0.3M) solutions at a temperature ono°c where major portion of the lead remains in the residue and zinc reports in solution. After taking out lead chloride by brine leaching, the residue has been treated for copper dissolution. A concentrated FeCI3 leaching at boiling temperature as well as ambient aqueous chlorine leaching have been separately tried to dissolve out the copper from the residue. Based on the results obtained, a flowsheet for the proposed process is presented.

Jan 1, 1981

By Irwan S. Halim

For tunnels in horizontally bedded rock, geologic factors affect the selection and design of the initial supports, including the rock propensity toward parting along bedding and the resulting high potential for rock slabbing during excavation. To evaluate this ground behavior, numerical analyses and results with Mohr-Coulomb, Hoek-Brown, and Ubiquitous Joint constitutive models were used, using the Upper Rouge CSO tunnel in Detroit, Michigan as an example. The different rock models and other geologic considerations are shown to impact the selection of the tunnel initial support and design. This paper emphasizes the appropriate selection of an analytical model based on the site specific geology to achieve an optimum initial support design.

Jan 1, 2008