Search Documents

A good deal of experimental work has been done from time to time on the application of compressed air to the elevation of wet pulp. On account of the flat nature of most of our mill sites elevation of the pulp has to be provided for, and the various methods in vogue show considerable loss of time, in the replaceing of wearing parts. During the last two years the writer has carried out a great many experiments with a view of devising an elevator that will give continuous work with a minimum of wear.The results do not show a high efficiency for the power employed, but the lift is continuous in operation, very cheaply installed, and possesses no wearing parts. The lift was tried working in a bore hole of 8 in. diameter, but in many cases it is more convenient to sink a small well for the purpose. The result to date showed that the most efficiency was obtained when the depth of the wellwas not less than the height of the lift required. The pressure of air required in pounds per square inch was (approximately) half the number of feet to be lifted.In the majority of cases the lift required varied between 20 ft. and 50 ft. and the air pressure required between 10 lbs. and 25 lhs. per square inch. In most existing installations the air compressors in use were delivering air to the receivers at about four times that pressure, and when air so compressed was expanded to perform its work at a reduced pressure, it was apparent that the power exerted in origInally compressing the air above the working pressure required at the lift was absolutely lost.

Jan 1, 1901

By Christopher J. Bise

INTRODUCTION The level of analysis for the selection of extraction practices and equipment for surface mining differs significantly from that found in underground mining. In underground mines, manufacturers establish the operating ranges of the equipment, such as continuous miners, loaders, and boring machines, based upon required clearances. Even in conventional mining, the drilling and blasting operation is usually based upon experience. The selection of extraction methods and equipment for surface mining is more complex. Since the equipment is not as confined as in deep mining, and the topography tends to be highly variable over the limits of the mining property, primary extraction equipment must be sized according to reach and capacity. Further, due to the depositional characteristics of the over- burden, drilling and blasting patterns must be well- designed to provide proper fragmentation. The following sections provide a general outline for the selection of surface excavation practices and equipment. The topics covered include drilling and blasting and the selection of both primary extraction equipment (draglines and stripping shovels) and secondary extraction equipment (bulldozers, scrapers, and front-end loaders). EXCAVATION FUNDAMENTALS Before discussing surface excavation, a few concepts need to be defined. A bank cubic yard of material is equal to one cubic yard as it lies in its natural or undisturbed state. A loose cubic yard is that portion of a bank yard that after being disturbed has expanded to measure one cubic yard. Swell is the volume increase of a material when it is removed from the natural state. Finally, load factor is the percentage decrease in the density of a material from its natural state to a loose state. Table 1 summarizes these concepts for various materials. When the amount of overburden to be removed to meet a predetermined production rate is established, a suitable bucket size for the primary stripping equipment must be calculated. The following equation can be used: NBSIZE = TBC/[(OF) (BF)] (1) where NBSIZE is the actual bucket capacity after considering the swell percentage, the bucket fill factor, and the operating efficiency; TBC is the theoretical bucket capacity (TBC = COB/NTCPM); OF is the operating efficiency; BF is the bucket fill factor; COB is the cubic yards of overburden to be removed; NTCPM is the number of theoretical cycles per month [NTCPM = (SMH) (3600)/(CT)]; SMH is the scheduled monthly hours; and CT is the cycle time in seconds. FRAGMENTATION PROCEDURES Drilling Where the strength of overburden material is such that blasting is required prior to excavation, drilling is conducted before using explosives. Two methods of drilling are found in mining-percussion and rotary. Penetration of overburden by percussion drilling is carried out by successive impacts of the bit into the rock. Emphasis in this section will be placed on rotary drilling, because for surface mining it is the most versatile form of overburden penetration. Rotary drilling is conducted by rotating a rigid string of tubular rods to which a rock-cutting bit is attached. The drilling energy is supplied by rotation as well as thrust and the cutting action consists of abrasion, scraping, spalling, or chipping. The size range for rotary-drilled blastholes is from 4 in. to 15 in., with 9 in. and 12 in. being common sizes. There are two types of bits used for rotary drilling-drag and rolling cutter. Drag bits are applicable in soft to medium-soft shales or their equivalents. Since their effectiveness is dependent upon a successful scraping action, drilling thrust is lower for drag bits than for rolling cutter bits; the opposite is true for torque requirements. The bits are usually fitted with replace- able tungsten-carbide cutters. Rolling cutter bits, though available in a two-cone configuration, are usually of the three-cone style (Table 2). The rolling cones have either large steel teeth for drilling through soft formations or small tungsten-car- bide inserts for drilling through hard formations. Table 3 relates bit size and weight to the strength of the rock. The major advantage of rotary drilling is its rapid drilling rate. This is due to the fact that, unlike percussion drilling, rock penetration is uniform with depth. Blasting Effective bank preparation deals not only with the fragmentation of overburden but also with the mini-

Jan 1, 1986

By R. Patel, D. R. Taylor, P. M. Varley

In-situ measurements of ground stress were made from surface boreholes, using overcoring and hydrofracturing techniques, to obtain data for the detailed design of the underground works at Pergau. Unexpectedly low stresses were measured and appeared to correlate with apparent hydrofracturing observed during permeability testing. The low values of the minor principal stress had a major impact on design, particularly of the lining for the pressure tunnel and shaft. Additional hydrofracture tests were made underground during construction of the low- and high-pressure headrace tunnels and the pressure shaft, to define the vertical reduction in the minor principal stress with overburden. These data were then used to locate and design the steel and reinforced concrete linings

Jun 19, 1905

By G. R. Peterson

To determine the availability of lead and zinc from demonstrated resources, the Bureau of Mines evaluated 235 mines and deposits in 31 market economy countries. Of the 235 mines and deposits evaluated for this study, 186 were evaluated as zinc operations, 30 as lead operations, and 19 as copper operations. Demonstrated lead-zinc resources of market economy countries in 1981 were approximately 4.3 billion metric tons (t) of ore containing 221 million t of zinc and 97 million t of lead. Of these amounts, approximately 154 million t of zinc and 70 million t of lead are estimated to be recoverable. The analyses indicate that demonstrated resources in market economy countries should be sufficient to satisfy projected demand for primary lead and zinc through the balance of the century. The U.S. lead industry will continue to have a comparative advantage over the rest of the world industry, barring any drastic increase in the cost of compliance with pollution control regulations. It appears that the comparative disadvantage faced by the U.S. zinc industry will probably intensify owing to the relative quantity of lower cost zinc resources in other countries, especially Canada, Australia, Mexico, and Peru.

Jan 1, 1985

By Shail J. Butani

In 1986 the Bureau of Mines conducted a probability sample survey, Mining Industry Population Survey, to measure such employee characteristics as occupation; principal equipment operated; work location at the mine; present job, present company, and total mining experience; job-related training during the last 2 years; age; sex; race; and education. The population estimates are necessary to properly analyze the Mine Safety and Health Administration (MSWA) injury (includes illness and fatality data) statistics; that is, to compare and contrast injury rates for various subpopulations in order to identify those groups that are exhibiting higher than average injury rates. This report uses the survey's results to characterize the U.S. metallic mining workforce from March through September 1986. Similar reports have been published for the stone, sand and gravel, and nonmetallic mining industries, as well as for the entire metal and nonmetal mining (includes metallic, stone, sand and gravel, and nonmetallic industries) sector and the coal mining sector.

Jan 1, 1988

By Eric S. Weiss

The National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research to evaluate explosion blast effects on typical U.S. mine ventilation stoppings in the NIOSH Pittsburgh Research Laboratory?s (PRL) Lake Lynn Experimental Mine (LLEM). An innovative Australian-designed brattice stop-ping was also evaluated. After mine explosion accidents, MSHA conducts investigations to determine the cause(s) as a means to prevent future occurrences. As part of these postexplosion investigations, the condition of underground stoppings, including the debris from damaged stoppings, is documented as evidence of the approximate strength and the direction of the explosion forces. The LLEM data showed that a typical dry-stacked and coated solid-concrete-block stopping survived a total explosion pressure of ~6.7 psi (~46 kPa) and was destroyed at a total explosion pressure of ~7.6 psi (~52 kPa). In comparison, a typical dry-stacked and coated hollow-core concrete block stopping survived a total explosion pressure of ~3.4?4.3 psi (~23?30 kPa) and was destroyed at a total explosion pressure of ~3.6?5.2 psi (~25?36 kPa), depending on the length of the pressure pulse and the value of the pressure-time integral. A typical steel panel stopping design survived a total explosion pressure of 0.8 psi (5.5 kPa) and failed at a total explosion pressure of 1.3 psi (9 kPa). The LLEM data also showed that an obstacle blocking the path of a pressure wave resulted in a higher reflected pressure at the obstacle. An 8-in (20-cm) thick wet-laid solid-concrete-block stopping coated on one side survived a total explosion pressure of ~26 psi (~180 kPa); this stopping was not tested to failure. A 6-in (15-cm) thick wet-laid solid-concrete-block stopping coated on one side survived a total explosion pressure of ~14 psi (~97 kPa) and was destroyed at a total explosion pressure of ~25 psi (~172 kPa). An innovative Australian woven cloth stopping survived an explosion pressure of 4.0 psi (27 kPa) and was destroyed at an explosion pressure of ~6.1 psi (~42 kPa). These results will help investigators determine the approximate explosion forces that destroy or damage stoppings during actual coal mine explosions.

Jan 1, 2008

By R. S. Dean

[During the past fiscal year the Metallurgical Division has made important contributions along the lines dictated by the Bureau policy of conservation of domestic mineral resources through Its investigations include determining of fundamental data of metallurgically important materials improvement of standard ore-treatment method to eliminate waste and improve the grade or recovery of the products; and development o new metallurgical processes.]

Jan 1, 1940

By R. S. Dean

[During t!~c past f isc.~l y~:-.r the Xetzllvz-gicd 3ivi oion has made im- portant contribution-, don,- tlie lines rlictnteil by the Bureau policy of con- servation of domestic rnker~l rcsoul-ces throui;h use. During t!~c past f isc.~l y~:-.r the Xetzllvz-gicd 3ivi oion has made im- portant contribution-, don,- tlie lines rlictnteil by the Bureau policy of con- servation of domestic rnker~l rcsoul-ces throui;h use.]

Jan 1, 1940

By R. J. Latino

Because of the lack of a universally accepted definition or standard for RCA, we are left to our own conventions in the marketplace as to what is most ?effective? or a ?Best Practice? for our own facilities or organization. This lack of uniformity in the application of RCA produces an equal lack of uniformity in the measureable outcomes of RCA on the bottom-line from site to site and industry to industry. What is the definition of success for an RCA? Is it regulatory compliance? Is it some quantifiable measure of bottom-line performance? Is compliance and bottom-line performance the same thing? Can we measure the ROI we receive by doing compliant RCA? These questions must be adequately addressed if any definition of RCA is to be effective on the bottom-line. Like our various Corporate Vision and Mission Statements, what would be our Vision and Mission for RCA? When pondering the answer to this question, we should consider: ? What Key Performance Indicators will the Success of RCA be Linked to? This provides a direct correlation to the corporate dashboard and therefore garners support for the RCA effort when implemented at the sharp end. Not until we know what KPI?s will effectively measure our maintenance and reliability objectives can we begin to establish which opportunities will afford the greatest returns1. ? What Bottom-Line Metrics will be Tracked to Measure the Effectiveness of Our RCA Effort? Will it be increased production, profitability, regulatory compliance, etc.? Will it be decreased injuries/fatalities, claims, customer complaints, risks, etc.? We should be specific about these metrics and their correlation to the metrics on our corporate dashboard. ? What Will Trigger an RCA Investigation? Normally companies will establish quantifiable thresholds to be surpassed before an RCA will be conducted. Examples may be an OSHA recordable injury, a failure event in which production losses exceed $250,000, an equipment failure in excess of $50,000 or a regulatory violation. This is the norm. However, we should realize this is using our RCA skills totally on a reactive basis. High Reliability Organizations (HRO) strive for proaction and they also use RCA proactively. Why can?t we use RCA to analyze why unacceptable risks from an FMEA are so high? It is perfectly applicable yet rarely implemented in this fashion.

Feb 27, 2013

By Gerald V. Gibbs

Quadratic functions, Q(hkl), are given to six places in increments of 0.01° for 2? from 0° to 90° for CuKa and from 25° to 180° for CuKa1. The wavelengths used for Cu in the computation are those agreed upon by the Editorial Commission of the International Tables for X-ray Crystallography (1950): CuKal 1.54051 A.; CuKa2 1.54433 A. INTRODUCTION At the Federal Bureau of Mines laboratory, Norris, Tenn., X-ray diffraction crystallography using tubes with copper targets revealed a need for a handy reference for the quadratic functions of copper radiation. The tables presented here were prepared to satisfy that need. The quadratic form Q(hkl) may be expressed in terms of the Bragg diffraction angle 2? and of the wavelength ? as

Jan 1, 1961

By Christopher J. Bise

INTRODUCTION Perhaps no other area reflects the art as well as the science of mining-engineering design quite as obviously as strata control. This is due to the fact that the design of mining structures is difficult because rock rarely behaves as a homogeneous medium. Further, the original state of stress and the mechanical proper- ties of the in situ rock are somewhat difficult to deter- mine. However, those aspects that are hard to treat mathematically can and have been successfully approached by model studies and in situ measurements. This chapter will review the fundamentals of strata- control design and will provide examples of applications to typical problems. STRESSES AROUND MINE OPENINGS A close examination of Fig. 1 reveals that, prior to mining, stresses exerted in the overburden can be in both the horizontal and vertical directions. In the example problems of Chapter 1, it was shown that the maximum compressive stress (uv) at any depth (D) below the surface can be approximated as follows: [ ] Further, the lateral stress (oh) is related to the maxi- mum compressive stress by utilizing Poisson's ratio (µ): [ ] As soon as a heading is driven, such as the one in the coal seam shown in Fig. 2, the stresses shift to the sides, or abutments, of the opening. Clearly, these compressive stresses around the opening exceed the pre-mining conditions. The problem of designing an underground opening, therefore, is to determine the maximum stresses and to note if they exceed the ultimate strength of the rock. Table 1 lists several rocks with their corresponding strengths. Figs. 3 to 5 depict the boundary stress concentrations around circular, ovaloidal, and rectangular openings. M is the ratio of the horizontal stress to the vertical stress, or as defined above, p/(l-p). This text will concentrate on the state of stress represented by M = 0.33, which corresponds to the condition of no lateral deformation in a rock having a Poisson's ratio of 0.25. For an ovaloid with an opening width-to-height ratio of 2.0 (Fig. 4), the boundary stress concentrations are at their maximum values at the comers of the opening, with values in excess of 3.0. If the depth of overburden is 500 ft, then the maximum boundary tangential stress ([ ] ) of the ovaloid is: [ ]

Jan 1, 1986

U.S. Minerals Coordinating Council Advised. -The Critical Materials Act of 1981, H. R. 4281, introduced on July 27, would create a Council on Critical Materials in the White House Executive Office to oversee Federal materials programs involving $1 billion committed to research by 14 agencies, and to serve as the President's focal point to evaluate materials policy. It was introduced by Congressman Fuqua (D-Fla.) whose Committee on Science and Technology has over-sight over the implementation of P. L. 96-479, the National Materials and Minerals Policy, Research and Development Act of 1980. Bulgaria's Mineral Bank. -Recently Bulgaria established a mineral bank to facilitate receipt of foreign credits for exploiting Bulgaria's mineral raw materials. The bank has wide powers to enter into business arrangements with foreign creditors. Bulgaria's main interest in trading with the West is to import the technology for developing energy and mineral resources.

Jan 1, 1981

By C. Anim-Sackey, R. K. Amankwah

Some large-scale mining companies in Ghana have adopted proactive management strategies in dealing with small-scale (galamsey) miners who have encroached on their concessions. This has been mainly achieved by ceding portions of the concessions held by the companies to the Minerals Commission of Ghana for licensing to the small-scale miners. This development has created an amicable relationship between the mining companies concerned and the galamsey miners in their host community. Ghana’s small-scale gold and diamond industry The small-scale gold and diamond mining industry in Ghana has existed for many centuries as an informal sector. Since the regularization of the activities of small-scale mining in 1989, two types of small-scale miners have emerged — legal and illegal.

Jan 1, 2004

By Bauduin C. Besix

The Eurocode 7 "Geotechnical Design" is based on "Limit State Design", tackling the uncertainties as much as possible at their source through: - selection of characteristic values of variables (loads, soil properties, pile resistance,...); - partial factors applied on the characteristic values; - model factors to account explicitly for uncertainties of the calculation rule if necessary. Eurocode 7 will propose three "design approaches". The selection of one of them will be by National Determination. For pile design, the approaches are: - approach 1 is a "material factoring approach" at load side and a "resistance factoring approach" at resistance side. The structural and geotechnical design are checked for both of two separate sets of partial factors. - approach 2 is a "load and resistance factoring approach" and is in several aspects close to a deterministic approach. The design is checked for one set of partial factors. - approach 3 is a material factoring approach, at load as well as at resistance side. The design is checked for one set of factors. The aim of this paper is to introduce to the design of pile foundations based on pile load tests and on ground test results (semi-empirical and analytical methods) in the frame-work of the three design approaches. Detailed attention is devoted to: - the selection of the characteristic value of the pile resistance, accounting for spatial variability and stiffness of the structure; - the reliability of the prediction of the pile resistance using analytical or semi-empirical methods which may be accounted for through a "model factor". The results of a large test campaign on screw piles in OC Clay and a calculation example illustrate the proposed procedure when calculation rules using CPT results are used.

Jan 1, 2002

By Rolf B. Pedersen, Ana Filipa Marques, Ingunn H. Thorseth, Ingeborg Okland

"Deep sea mining of polymetallic sulphides will change the physical and chemical conditions at the seafloor by creating scars when sulphides are removed, and potentially also by deposition of mine tailings at the seafloor. These changes will impact the existing ecosystems at the seafloor in and around the mined areas. Seafloor Massive Sulphide deposits that have been exposed to oxic seawater weather into Fe-metal-oxyhydroxides. However, the rates of weathering and release of heavy metals and other toxic compounds to the environment from freshly exposed sulphides in a deep-sea environment are not well studied.During a cruise to the Arctic Mid-Ocean Ridge in the Norwegian-Greenland Sea in July 2014 we will initiate in-situ experiments investigating the microbiological and geochemical processes involved in the weathering of freshly exposed massive sulphides deposits in a natural environment. This will be done by creating scars in naturally occurring sulphide deposits and by deploying weathering experiments at the seafloor. The sites will be revisited and re-sampled in 2015. The mobility and fate of heavy metals will be one of the main concerns of the study as well as constraining the time it will take for exposed sulphides to return to the chemical state present prior to mining. In this presentation we will present the experimental framework and the preliminary results from the July 2014 cruise. This project is part of the EU funded MIDAS (Managing impacts of deep sea resource exploitation) project."

Sep 1, 2014

By R. V. Ramani

One area of study in the Coal Mine Injury Analysis project was to illustrate and enhance the ability of mine safety management personnel to apply analytical techniques to injury experience data and to justify requests for funds for safety enhancement actions on a cost/benefit and other quantitative basis. Four volumes of this final project report detail (1) the objectives and scope of the mine safety management research, (2) the results of literature review, and case studies, and (3) models developed for mine safety management. The four volumes are titled as Volume III: Mine Safety Management, Volume IV: Analytical Techniques for Mine Safety Management; Volume V: Mine Safety Management Case Studies and Volume IX: Training Cost Model. This volume deals with the development of a microcomputer based training cost model (TCM) which can be used to analyze training cost implications of various types of training. The model has been developed using Aston Tate's dBASE III plus language. The computer program and a test run of the model are presented in this report.

Jan 1, 1993

By Frank B. Fulkerson

Of the about 60 million pounds of aluminum used in the Pacific Northwest in 1960, 40 million pounds or two-thirds was used by 10 companies. One of these companies made airplanes and missiles; one manufactured roofing, siding, and tubing; three produced truck tractors, truck bodies, or truck trailers; two made architectural metal products; one made irrigation and industrial products; one was a general foundry; and one was a shipyard. These companies contributed to regional growth by developing markets outside the area; some have worldwide sales. Aluminum consumption increased at an average rate of 7 percent annually from 1954 to 1960. Airplane manufacture, formerly preeminent in aluminum use, no longer was in first place in 1960. By industrial group, the leading users were manufacturers of building products, 30 percent; airplanes and missiles, 22 percent; truck tractors, truck bodies, and truck trailers; 17 percent; general foundries, 5 percent; ships and boats, 4 percent; mobile homes, 4 percent; other transportation equipment, 3 percent; and irrigation equipment and all other products, 15 percent.

Jan 1, 1962

By D. E. Wolfson

As part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report.2/ The suitability of coal for metallurgical use depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, as well as the available reserves, are considered in selecting coals for carbonization tests. According to the estimate of reserves by Dowd,3/ the recoverable coal in Raleigh County in beds 28 inches or more thick, in thousand tons, is: [ ]

Jan 1, 1957

By Michael McVay

The use of augered cast-in-place piles has seen tremendous growth under commerical structures in the past twenty years. Problems with vibration, soil densification and/or heave associated with driven piles do not occur with properly installed augered piles. Augered cast-in-place piles were originally constructed (1950s) with diameters of .31 m (12 in.) and lengths up to 6.1 m (20 ft); however with the advent of better drilling equipment, diameters varying from .41m(16 in.)to .61 m (24 in.) and typical depths ranging from 18.3 m (60 ft) to 24.4 m (80 ft) are achievable. Reinforcement may vary from a single high strength rebar (Grade 60) at the top of the pile to a continuous steel cage depending on loading (compression, tension-uplift, and lateral). Typical axial design loads (compression) for a single augered cast-in-place pile are in the 445 kN (50 tons) to 890 kN (100 tons) range.

Jan 1, 1997

By D. F. Malan

This paper gives an overview of the difficulties associated with determining the strength of hard-rock pillars. Although a number of pillar design tools are available, pillar collapses still occur. Recent examples of large-scale pillar collapses in South Africa suggest that these were caused by weak partings that traversed the pillars. Currently two different methods are used to determine the strength of pillars, namely, empirical equations derived from back analyses of failed and stable cases, and numerical modelling tools using appropriate failure criteria. The paper illustrates that both techniques have their limitations and additional work is required to obtain a better understanding of pillar strength. Empirical methods based on observations of pillar behaviour in a given geotechnical setting are popular and easy to use, but care should be exercised that the results are not inappropriately extrapolated beyond the environment in which they are established. An example is the Hedley and Grant formula (derived for the Canadian uranium mines), which has been used for many years in the South African platinum and chrome mines (albeit with some adaptation of the K-value). Very few collapses have been reported in South Africa for layouts designed using this formula, suggesting that in some cases it might yield estimates of pillar strength that are too conservative. As an alternative, some engineers strongly advocate the use of numerical techniques to determine pillar strength. A close examination unfortunately reveals that these techniques also rely on many assumptions. An area where numerical modelling is invaluable, however, is in determining pillar stresses accurately and for studying specific pillar failure mechanisms, such as the influence of weak partings on pillar strength. In conclusion, it appears that neither empirical techniques nor numerical modelling can be used solely to provide a solid basis for conducting pillar design. It is therefore recommended that both these techniques should be utilized to obtain the best possible insight into a given design problem. Owing to the uncertainties regarding pillar strength and loading stiffness, monitoring in trial mining sections and in established mining areas is also an essential tool to test the stability of pillar layouts in particular geotechnical areas.

Jan 1, 2011