Search Documents

By Daniel Mageau

Ground freezing has been used for over 100 years to provide shoring and ground water cutoffs for hundreds of projects worldwide, including drilled shafts, tunnels and cofferdams. Typically, these cases involved difficult soil/water problems where ground freezing was likely the only solution. This paper discusses a recent ground freezing project where a frozen soil wall was used for a more conventional problem. A 4-foot-thick frozen soil wall was used to provide shoring and groundwater cutoff for a 20-foot-deep excavation during construction of a cast-in-place concrete storm water detention vault. The site is located along the northbound on-ramp to I405 from westbound SR522 in Woodinville, Washington. The frozen soil wall was successfully formed in soils consisting of till fill over soft organic silt and loose saturated sand in about 3 weeks. The depth to ground water varied from about 4 to 8 feet over the site. The unfrozen soil inside the frozen soil wall was excavated vertically to the frozen soil boundary. The vertical excavation remained open for approximately 2 months with no dewatering required. On one side, fully-loaded dump trucks and other construction equipment operated within 6 feet of the wall face with zero wall movement. This paper addresses the construction issues related to installation and operation of ground freezing shoring. The overall wall performance of the frozen soil wall as well as basic geotechnical design issues are also discussed.

Jan 1, 1998

By W. C. Winegard, A. Galibois, C. J. Beingessner

The effects of solutes on the distribution of two-dimensional configurations of grains in zone-refined tin have been studied. When solutes with partition coefficients (ko) greater than unity are added, three-sided pains become more prevalent and the growth law changes. It is shown by electron-Probe micro-analysis that a solute buildup occurs ahead of a moving grain boundary when ko > 1. It has been found recently1, 2 that solutes with partition coefficients greater than unity have a larger retarding effect on grain growth than solutes with k, less than unity. ko is defined as the ratio of the concentration of solute in the solid to the concentration of solute in the liquid with which the solid is in equilibrium. Niessen and winegard2 have suggested that this effect is probably due to the complex shape changes which occur during the process of grain growth and that no theory based on single boundary motion3-5 can explain the results. They suggested that the dissociation of the unstable fourfold junction was delayed in alloys where ko was greater than 1 because the boundaries at the junction had to move into a region of high solute concentration. If indeed this mechanism were correct, it was felt that not only would the dissociation of fourfold junctions be affected by the solute buildup ahead of the boundaries, but the collapse of three-sided grains would be impaired. These combined effects would naturally lead to a modification in the distribution of the number of sides per grain seen on a two-dimensional section. The present investigation was undertaken to test these hypotheses by examining the grain-growth process in detail. EXPERIMENTS The Distribution of Grain Configurations in Zone-Refined Tin as Seen on a Two-Dimensional Section. Following the method of Bolling and Winegard,6 zone-refined tin was cast into button-shaped specimens and, subsequently, plastically deformed under a drop hammer at room temperature. The resulting flat coin-shaped samples were annealed at 200°C, some for 50 sec and others for 100 sec. The specimens were then examined to determine the distribution of the number of sides per grain, i.e., the num- ber of crystals adjacent to any particular grain in the section. For simplicity, the grains were classified as three-sided, four-sided, and so forth; this concept is schematically illustrated in Fig. 1. As indicated by smith,' it was necessary to examine every grain within an enclosed area to obtain a proper distribution of the relative frequency of each type. The distributions for the two annealing times are illustrated in Fig. 2. The total number of grains examined is also indicated on the figure. It is evi-

Jan 1, 1965

By Donald E. Raab, Lee W. Saperstein

INTRODUCTION The Premise Not much time has to be spent in a tunneling project to realize the tremendous interdependence that exists among the various unit operations. The research that is to be described attempts to examine one set of these linked operations, namely, the effect of cutters on muck handling properties. All too often research focuses on too minute an aspect of a problem for the results to be of much immediate, practical use. The goal of this research is to avoid this specificity. Apologies are tendered if this goal is missed. It is known that the mode of flow of bulk solids under the influence of gravity -- emptying a bin or hopper -- is dependent on several basic parameters. The size of the particles and the distribution of sizes (consist) determine whether the solids will first flow out of a given aperture; the cohesion of the solids will determine if flow will continue after the bin is opened; and the angle of internal friction determines the size of the flow regime (1,2,3). It is well understood that the latter two parameters affect the behavior of bulk material on a conveyor belt. Cohesion of material to a belt is always an undesired problem. Heaping of material on a belt depends on the material's internal friction. It is also known that varying the particle size, and the packing density of the material can affect the material's angle of internal friction (4,5). The question was posed whether sufficient variation in a mechanical tunneling machine's (mole) cutting function could be arranged to affect materially the handling properties of the muck

Jan 1, 1974

By Eleanor Sonley

In October 2000, temporary seismographic stations were installed above the Trail Mountain Mine, Emery County, Utah, USA to supplement a regional network. Over seven months, 1826 mining-induced seismic events were recorded with a magnitude range of M 0 to M 2.2 (Arabasz et al., 2002, 2005). Routine event locations for this dataset cluster around the longwall mining activity during the recording interval. However, applying a double difference relocation technique to the routine locations significantly improves the correlation between mining activity and event location. The resulting relocations depend greatly on station distribution and the number of arrival time picks. We use this dense temporary array to assess station distribution requirements for applying the double difference technique at other mines by systematically removing data from available stations, thus simulating sparser networks. The insight gained using the Trail Mountain dataset is used to develop a metric for assessing the usefulness of above-mine networks and to develop a tool for expanding seismic network coverage. To verify the appropriateness of these tools for wider application, we examine data from two additional mines located in the western United States. Improving the relative locations of mining-induced seismic events highlights the association of these events with active portions of the mine. Clusters, regions of quiescence and relative timing of events can be used by mine operators to assess hazard, optimize production, and evaluate performance of mine plans. The lessons learned from this study may be used in future network design to improve accuracy of event locations at other mines.

Jan 1, 2009

By J. I. Muñoz González

El presente trabajo verifica la utilidad de la incorporación de algoritmos de inteligencia artificial (IA) en cuanto a mejorar los resultados obtenidos en campañas de sondajes de exploración. Tomando la información geológica, geoquímica y geofísica de un proyecto real de exploración, se simularon 3 campañas posteriores y consecutivas, utilizando algoritmos de “boosted regression”. Luego fueron comparados con los resultados reales de los mismos.

May 1, 2008

In the Ngakuru area, zeolite deposits occur in late Quaternary lake sediments and ignimbrites. The deposits are associated with sinters, hydrothermal eruption breccias, and quartz-adularia altered fault breccias: all indicators of a shallow epithermal environment. Several of the deposits are adjacent to epithermal gold prospects. Zeolites are most abundant in lacustrine tuffs of the Ngakuru Formation, a 100-300 m thick sequence of siltstone, tuff, diatomite, sandstone and conglomerate. The formation overlies the Ohakuri Ignimbrite dated at c. 270 Ka, and is unconformably overlain by alluvial sands and gravels which are younger than 20 Ka. Individual zeolite deposits contain 30-80 per cent zeolite over a thickness of up to 45 m in thinly stratified tuff beds. The tuff beds are locally overlain by diatomite. The tuffs are composed mainly of glass shards and pumice clasts, with minor volcanic plagioclase, quartz and biotite crystals. Glass shards in the tuffs are replaced by the silica-rich zeolites mordenite and clinoptilolite. Amorphous silica (opal A), opal-CT, K-feldspar and smectite are also present. The distribution of the Ngakuru Formation is controlled by northeast trending normal faults, which separate it into the Ngakuru and Guthrie grabens. A silicified (quartz-adularia altered) hydrothermal breccia along one of the fault zones suggests that the faults acted as feeders for heated water that caused the deposition of the zeolite minerals. Some of the zeolite deposits are adjacent to sinters and hydrothermal eruption breccias. The location of the sinter about 20 m above one deposit indicates that the zeolites were formed at a depth of 20 to 70 m below the paleosurface. The hydrothermal eruption breccias contain clasts of altered ignimbrite, which contain geochemically anomalous gold and silver values. By analogy with their occurrence in active geothermal systems in the Taupo Volcanic Zone, mordenite and clinoptilolite in the Ngakuru deposits probably formed at temperatures of 60-150oC from near-neutral pH waters as a result of interaction with glass-rich tuff beds. The Ngakuru zeolite deposits are therefore interpreted as shallow hydrothermal alteration zones within larger epithermal gold-bearing systems.

Jan 1, 2002

By Omid Lashkari

Keywords: SEED, SSM materials, Microstructural evolution, Rheology, Swirling Speed SEED (Swirled Enthalpy Equilibration Device) is established itself as a new technology amongst the many Semi-Solid Metal (SSM) processes, where swirling of the mush plays an important role in modifying the dendritic structure of as-cast parts. A range of semi solid metal structures, dendritic, rosette and/or globular morphology of primary phase, can be prepared using SEED. The current article reports on the application of rheological tests in characterizing microstructural evolution during SSM processing of 356 Al-Si foundry alloy. A simple parallel plate test machine, designed and constructed at our labs, was used to determine viscosity values for each structure and identify the optimum structure with superior die filling characteristics. Such findings have important technological and economical implications during high pressure die casting of semi- solid metals. The strain-time graphs for 356 Al-Si foundry alloy indicated lower viscosity values for globular microstructure, i.e. improved die filling.

Jan 1, 2005

By Y. Nakata, K. Nagata

Plasma is partially ionized gas composed of ions, electrons and activated elements at high temperature. Some flying ash from incinerated municipal waste is melted to become glass by a transfer-type arc plasma furnace. As the glass is ionic silicate, when an electric current passes through anode to cathode, ions in molten slag electrochemically react with electron in plasma at the surface of molten slag. In case of molten Na2O-SiO2, sodium ions in the molten slag carry electric current and SiO2are reduced to evaporate as SiO gas by electron in plasma. The cases of Ag+in NaNO3-KNO3molten salt and Fe2+in FeO-SiO2slag were examined. The amount of cathodic reaction is larger than that of anodic reaction and not apparently according to the Faraday?s law on the electrochemical reactions.

Jan 1, 2004

The labour question is one that has caused mine managers much thought and anxiety and is likely to continue to do so as long as human beings exist. The difficulty is to devise some arrangement whereby the interests of miner and mine ownerare identical. Mines cannot be worked without capital, and capital is no good without labour, yet, though both have the mine in common, their interests are not exactly the same. Some men are happy so long as they can scrape through by exerting themselves as little as possible, but capitalists do not work mines for charity, they want some return for their money.Where a large number of men are employed there are bound to be examples of all sorts, good and bad, and it is because one cannot depend on all, that different methods of employment have to be adopted. Which method is selected depends to a great extent on the labour market, local conditions, nature of the ore and the way in which it occurs.A big step towards success is obtained by securing the services of good bosses, not only those who know how work should be done, but men who have a knowledge of human nature. It is a big mistake to be too lenient with a man, also to be unnecessarily harsh. A good boss will always be sought out by good men who have worked under him before, or who have heard of him from others. By a good boss we do not mean one who employs two men where one would do, or who lets the men loaf...

Jan 1, 1901

By Åke Krukka, Heribert F. Broicher

"The iron ores of the Kiruna Mine in Sweden are of exceptional quality but for the phosphorus content in certain zones of the orebody. The prevention of mixing ores high in phosphorus with those low in phosphorus has always been of significant economic importance. The ongoing introduction of tele-mining and automatic haulage by LHDs requires new means in the field of quality control underground, as the experienced miner as well as the underground laboratory assistant no longer are involved in the process. As of 1998 LKAB has been testing prototypes of LIF Analysers for non-contact and real-time measurement of the phosphorus content of ore being transported by LHDs from the stopes to the respective ore pass assigned to a certain ore quality. The principles of the analysis of laser-induced fluorescence, the different test phases and results are described and conclusions made. With bulk sorting of ore underground the mining engineer supports the efforts of the metallurgist in the processing plant.INTRODUCTIONThe Kiruna Mine of LKAB, Sweden is the largest underground iron ore mine in the world. In the early nineties LKAB decided to develop the Kiruna orebody further down from the 775m main level to a new main level at 1045m. This development programme was realised while in the mineral processing section and in the pellet plant further capacity was added (Wyllie 1996).In addition to deepening of the mine, which opened up 330 million tonnes of ore, the exploitation of the so-called lake ore was included in the future planning, adding another 1 15 million tonnes of mineable ore. At an annual production of approximately 20 million tonnes of ore the Kiruna Mine today looks at a developed ore reserve sufficient for the next 20 years.All of the competitors’ ores traded in the world market are from open pit operations. LKAB compensates for the obvious disadvantages by continuous efforts to make the best possible use of her high quality magnetite ore deposit. This objective is realised by combined efforts in the pellet plant, the mineral processing plant and the mine. Propriety processes, latest big scale equipment and high tech solutions for automation lead to high quality sales products at a reasonable cost."

Jan 1, 2002

By Georgene Renner, William R. Yernberg, Steve Kral

ABB provides integrated pro-cess control, optimization and information systems, drives and power-distribution equipment as well as other services and support to the mining industry. ABB also supplies electrical equipment and control systems for the openpit mining industry. This includes products for the automation of electrical equipment in mine shovels. The company offers low- and medium-voltage drives for various mineral- industry applications. And ABB provides gearless mill drives for equipment, such as semiautogenous grinding mills that are too large for conventional drives. ABB Industrial IT provides innovative hardware and software systems that cover all the requirements of the modern mining and processing plant.

Jan 1, 2004

By Litvinenko V. I

Being a source of structural materials for many centuries, the modern image of the ferrous metallurgy is burdened with obsolete technologies with disregard towards new environmental protection requirements. The production cycle of metallurgical products have two clear-cut stages: I . production of liquid metal and casting into steel billets; and 2. processing of steel billets in solid state under high temperature to produce various shapes and profiles of metal products. Plastic deformation of metal at the second stage is least associated with environmental pollution and is presently being provided with more and more advanced equipment.

Jan 1, 1999

By R. E. Wilmot

This paper is based on the experiences, over many years, on the part of numerous authors in the South African mining industry and that of the hot dip galvanizing process and its application as a corrosion protection system. The paper sets out the extensive development, financial resources and stringent operating requirements of the South African mining industry. After many years of research and operational experiences, hot dip galvanizing and when necessary, duplex systems, have been found to meet the demanding requirements of this particular industry. The paper sets out the requirements from the standpoint of corrosion criteria and is followed with a practical example; ?case history? where the corrosion protection properties of hot dip galvanizing are demonstrated. This case history traces the early investigation of the expected corrosive conditions to be encountered in a new mining operation (now 10 years on) and concludes with two follow up visits to the mine in order to examine actual performance of the corrosion protection system after ten years in service.

Jan 1, 2006

By G. Tamaro

The World Financial Center is situated on a 60,000 square meter site at Battery Park City at the southern tip of Manhattan Island. The foundations for the buildings and the related infrastructure posed difficult design and construction problems since the site was filled land in the Hudson (North) River. Foundation construction was made difficult by both the geology and the existence of two railroad tunnels which passed under the site. The soils at the site were unsuitable to support construction of heavy structures, and as a result, all of the foundations had to be carried down to bedrock, or the glacial till over rock. Two buildings were supported on piling and special battered caissons which provided lateral support against wind loading. The other two buildings were supported directly on rock, requiring excavation to depths of 19 meters (63 feet) below grade.

Jan 1, 1989

By P. Grainger, P. G. Kalaugher

Paper presented at conference and first published in preprint volume of: Risk assessment in the extractive industries, held in University of Exeter, 23-24 March 1994. London: IMM, 1994. Large, unpredicted ground movements resulting from open cast or underground mining present risks to the safety and economy of extractive industries. As large, sudden failures are usually preceded by small displacements at a much slower rate, the detection and monitoring of these minor changes to the ground surface provides a means of assessing the risks. It is recommended that a visual approach is often preferable to surveying or fixed instrumental measurements. An optical system has been devised, incorporating a 35 mm camera, which allows an immediate comparison on site between a colour transparency taken on a previous inspection and the scene it represents. The observer fuses the transparency stereoscopically with the directly viewed scene. The impression is close to that of normal vision except that differences in detail which have occurred since the transparency was taken are immediately obvious, enabling a qualitative assessment of changes to be made on site. If repeat photography is required it can be taken with exactly the same alignment and coverage. The two images are then available for office analysis using simple micro-photogrammetry

Apr 1, 1996

By D. E. Sherwood

Recent developments in high torque hydraulic rotary rigs has lead to the construction of secant bored pile walls by rotary drilling methods in circumstances where earlier methods were difficult and in some cases impossible. The evolution of secant bored pile wall construction is described including classical, rotary drilled and continuous flight auger construction methods. The paper then details the restraints which have been created in recent inner city redevelopment, many of which were not relevant in the early days of the technique. Typical examples of walls are presented to show the adapatability and advantages of the secant bored pile wall method. A number of in-situ retaining wall construction techniques are then compared in detail with regard to relative cost, technical quality and practicality.

Jan 1, 1989

By Clayton V. Deutsch

Indicator Kriging (IK) is being commonly applied to mineral resource assessment problems. More recently, indicator simulation has also been used for sensitivity analysis and difficult change of support problems. The essential theory underlying indicator geostatistics has not changed since its introduction 10 years ago; however, the last decade has produced many important developments in its implementation. The objective of this paper is to consider some of the more important implementation details. Examples from the Porgera gold deposit in Papua New Guinea are used to illustrate the steps in an indicator geostatistical study and the importance of various implementation decisions. Specifically, in many precious metals deposits the continuity of the grades is typically quite anisotropic. This anisotropy varies in both magnitude and direction throughout the deposit. Building a model of this anisotropy can considerably improve the local kriged or simulated points. One approach to build this model is presented. In addition, there is typically more than one mineralization style and geological rock type; the spatial character of the mineralization can be quite different within each geological rock type. The rational treatment of anisotropy and geological subdivisions is common to all mineral resource assessment procedures; the importance of this qualitative geological information is not diminished with more sophisticated techniques such as indicator kriging. This paper presents an overdue comprehensive look at the practical aspects of indicator methodology. Many of the techniques and procedures documented in this paper have been developed during the course of detailed mine feasibility studies.

Jan 1, 1992

By J. R. Nettle

The development of a process for upgrading offgrade titanium metal by electrorefining in molten salt led to an investigation of the electrotransfer characteristics of selected metals when alloyed with the titanium to be refined. Previous tests on seven binary titanium alloys showed that the degree of transfer of the alloying constituent depends on the constituent and on the operating procedurese.5 This report describes tests on electrorefining ternary mixtures of titanium with selected metallic elements. Ten alloys were prepared from high purity titanium and 2-1/2 percent of each of the metal pairs selected from the same elements used in the binary study; manganese, vanadium, chromium, zirconium, tin, molybdenum, aluminum. Operating variables were similar to those investigated in the binary alloy study that gave minimum alloy metal transfer. The data presented indicate the transfer characteristics of the various metals and combinations tested relative to each other.

Jan 1, 1962

By Koch D. F A

An electrochemical study of the dissolution of gold in aerated cyanide solution shows that the dissolution rate is determined by the nature of the surface. A passive film (probably a basic cyanide) formed at -0·6 V vs a saturated calomel electrode inhibits both the anodic dissolution of gold and the cathodic reduction of oxygen. Thallium has an "activating" effect on these reaction mechanisms.INTRODUCTIONIn general the dissolution rate of a solid in a liquid is studied by weight loss measurements or analysis of the solution at known time intervals. However, if the solid is a metallic conductor, on which a redox reaction can occur at the metal-solution interface, it can be studied by electrochemical techniques. Electrochemical measurements have the advantage that the overall reaction can be separated into its components, in some cases by electrical measurements alone, and in others by a combination of these with analytical determinations.The overall equation for the dissolution of gold in aerated cyanide solution may be written4Au + 02+ 8CN- + 2H20 = 4Au (CN)2- + 40H- ..... (1)which can be separated into the two electrochemical componentsrepresenting the oxidation of gold and the reductionof ogygen respectively.4Au + 8CN-,= 4Au(CN)2- + 4eand O2+ 2H20 + 4e = 40H- These two reactions occur at the gold-electrolyte interface and it is the purpose of this paper to discuss the mechanism...

Jan 1, 1964

By Clyde Sitterud

Presentation Agenda ?Global Mining Tire Demand ?What is driving it? ?Latest Situation ?How long it will last? ?Michelin?s Response to Increase Supply ?New plant ?Additional presses ?Recommendations for Mining Users ?Treat tires as your major assets ?Areas of attention that will produce immediate results

Jan 1, 2005