Search Documents

By L. McWilliams, L. D. Patts, J. D. Noll, S. E. Mischler

Elemental carbon (EC) is currently used as a surrogate for diesel particulate matter (DPM) in underground mines since it can be accurately measured at low concentrations and diesels are the only source of submicrometer EC in underground mines. A disadvantage of using EC as a surrogate for DPM is that the fraction of EC in DPM is a function of various engine parameters and fuel formulations, etc. In order to evaluate how EC predicts DPM in the underground mining atmosphere, measurements of total carbon (TC; representing over 80% of the DPM) and EC were taken away from potential interferences in four underground metal/non-metal mines during actual production. In a controlled atmosphere, DPM mass, TC, and EC measurements were also collected while several different types of vehicles simulated production with and without different types of control technologies. When diesel particulate filters (DPFs) were not used, both studies showed that EC could be used to predict DPM mass or TC. The variability of the data started to increase at TC concentrations below 230, µg/m3 and was high (>+20%) at TC concentrations below 160 µg/m3, probably due to the problem with sampling organic carbon (OC) at these concentrations. It was also discovered that when certain DPFs were used, the relationship between DPM and EC changed at lower DPM concentrations.

By A. M. Elmahdy

An amphoteric collector was tested for dolomite removal from phosphate ore. The effects of some operating parameters and their significance on the flotation of dolomite were studied using statistically designed experiments. The parameters studied were impeller speed, pH and collector dosage. Analysis of the results showed that pH is the most significant parameter. Moreover, a concentrate containing 0.53% MgO and ~31.1% P2O5 with a recovery of ~ 90% can be achieved at optimum values of studied parameters, i.e., a pH of 12, an impeller speed of 1,000 rpm and a collector dosage of 2.5 kg/t.

Jan 1, 2007

Salaries for mining professionals have gone up substantially in the last two years across most vocations and there has never been a better time to enter the industry, in terms of career opportunities and salary packages. With so many offers on the table and companies outbidding each other to attract the best talent, many new professionals are being lured in by the big money, sometimes at the expense of a satisfying career and a sustainable lifestyle. What should we consider when accepting a new position? What are our values, and how do these drive our decision making? This paper examines our core values as people and makes some observations about what it takes to really succeed in the mining industry.

Jan 1, 2006

By Larissa Koroznikova, Steve Durkin, Patrick Bouwmeester, Michael Tuck

In currently used mining methods, blasting techniques often causes dilution of valuable ore and results in costly processing requirements. In the context of narrow vein mining of thin and highly concentrated orebodies there is a need of a mining method that can reduce dilution in order to remain economically viable. This research project explored the viability of a new mining technology, thermal fragmentation, in narrow vein mining. Thermal fragmentation technology uses a flame jet to produce extreme heat that spalls the surrounding rock to a strategically located drill hole, as an alternative to traditional blasting. This paper creates a net present value (NPV) model of a mining method using thermal fragmentation, as well as for an existing method used for narrow vein mining; comparisons and evaluations were made regarding the feasibility of the new technology. It was found that while overall costs for thermal fragmentation were relatively high, reductions in wages, haulage and processing costs, as well as increased productivity and ore recovery, meant that the new method would improve the financial performance of any operation. These results identify that there is an opportunity to introduce the thermal fragmentation technology to narrow vein mines within Australia, in order to lower costs and increase profit.

The roasting of sulphide ores and concentrates is often the first step in the production of metals or chemicals. In many processes, the production of sulphuric acid is viewed as a by-product, while in some plants production is an important economic factor. Regardless of the purpose, a pyrite roasting plant consists of mainly three plant sections: roasting, gas cleaning and sulphuric acid. With the addition of air, the pyrite concentrates are transformed into solid oxides and gaseous sulphur dioxide at temperatures of 600 - 1000° C. After cleaning and cooling, the sulphur dioxide in the roasting gas is further processed to sulphuric acid. Two types of reactors are used depending on the application: stationary or circulating fluid bed . For over 60 years, Outotec has progressively been developing the principle of fluidised bed technology in several different reactor types for a multitude of process applications. The versatility of the fluidised bed reactor system has manifested itself in the treatment of minerals, including solid fuels, and for metallurgical processes both in the ferrous and non-ferrous fields. Process applications have included roasting, calcining, combustion and charring of coals, as well as off-gas treatment. This paper provides a summary of the pyrite roasting technology currently used along with a simple cost comparison of pyrite roasting and sulphur burning processes.

Jan 1, 2009

The roasting of sulphide ores and concentrates is often the first step in the production of metals or chemicals. In many processes, the production of sulphuric acid is viewed as a by-product, while in some plants production is an important economic factor. Regardless of the purpose, a pyrite roasting plant consists of mainly three plant sections: roasting, gas cleaning and sulphuric acid. With the addition of air, the pyrite concentrates are transformed into solid oxides and gaseous sulphur dioxide at temperatures of 600 - 1000° C. After cleaning and cooling, the sulphur dioxide in the roasting gas is further processed to sulphuric acid. Two types of reactors are used depending on the application: stationary or circulating fluid bed . For over 60 years, Outotec has progressively been developing the principle of fluidised bed technology in several different reactor types for a multitude of process applications. The versatility of the fluidised bed reactor system has manifested itself in the treatment of minerals, including solid fuels, and for metallurgical processes both in the ferrous and non-ferrous fields. Process applications have included roasting, calcining, combustion and charring of coals, as well as off-gas treatment. This paper provides a summary of the pyrite roasting technology currently used along with a simple cost comparison of pyrite roasting and sulphur burning processes.

Jan 1, 2009

By Frank Cook

In this two-year study, an evaluation of mining and reclamation practices at 159 randomly sampled surface coal mines in the United States was conducted. It is concluded that reclamation practices in most of the 22 coal-producing states were adequate during 1975, but that improvement in reclamation performance was desirable in the acid area of the central U. S. and in mountainous southwestern Virginia. Productivity improvements should result from research to determine efficient or optimal operating procedures for dragline stripping of single and multiple seams, surface mining of lignite, multicut and multiseam haulback mining on steep slopes, mountaintop removal, and surface mining in swampy or deeply glaciated areas. Specific candidate research projects are discussed in this report.

Jan 1, 1976

The area between Merrygoen and Digilah is located on a structural high that separates the Sydney Basin from the Great Artesian Basin, and hence the stratigraphic succession of younger rocks overlying the basement is relatively thin. The stratigraphy is briefly described and it is shown that fluvial sedimentation prevailed from Upper Permian through to Middle Jurassic times. Flint clays occur in the Permian, Triassic and Jurassic but only those in the Jurassic appear to have commercial value at present. The chemical, mineralogical, and physical properties of the flint clays are discussed.

Jan 1, 1973

By Ed Billington, Mike Shields

The trail blaster is faced with a wide range of workrelated challenges, not the least being the work setting itself. It is usually remote, being anywhere from 5 to 30 or more miles (8 to 50 km) from any road. It may be in mountains, high rock desert, or coastal rain forest, and can range from sea level to over 12,000 feet (3700 m) in elevation. The blaster may be part of a 2-person clearing crew, a 4-person maintenance crew, or a 10-person construction crew. The crew will usually be mobile, moving and working up to 10 miles (16 km) or more per day, relying mostly on their own backpacks to move camp, tools and supplies from site to site. Periodic resupply may be by helicopter, aird rop, or even “sherpa” groups, but most often will be by packstrings of horses and mules. The crew goes into the backcountry a n y w h e re from two weeks to three months at a time, and while there, its members “live the job” 24 hours a day, enjoying baking heat, torrential rain or mid-July s n o w s t o rms along with the truly glorious weather that c o m p e n s a t e s . So who is this blaster? Well, “he” may be she, since some of the top trail blasters are women. He/she will also be more than a blaster: Crews are small, so experienced members must be capable of handling the full range of trail work. Thus this blaster is also a driller, and usually also a bucker, snag faller, rigger, dry-stone mason, log and timber carpenter, bridge builder, mule p a c k e r, small-engine mechanic and, not least, camp cook capable of putting out a hot meal from a campfire , in a downpour, in the dark. Being in remote locations, often without reliable communication to the outside world, trail crews enjoy a remarkable degree of independence from “supervision.” With that comes the responsibility to make sound decisions which expedite the work, while promoting crew safety and welfare .

Jan 1, 2004

By J. Muller

Keywords: Pyrometallurgy, blast furnace, slag viscosity, slag liquidus temperature, phase equilibria The viscosity of molten slag in blast furnace operations is an important process variable, influencing the rate and location of reactions inside the furnace, as well as the ease with which the final slag could be removed from the furnace. To optimize these processes, it is necessary to estimate the slag viscosity and liquidus temperatures as accurately as possible, and know the target values. Models to predict viscosities and liquidus temperatures, incorporating phase equilibrium calculations, have been developed and validated with measured data. Various diagrams have been developed to illustrate how the properties vary with composition and temperature, including pseudo-ternary diagrams of SiO2-MgO-CaO-Al2O3 for viscosity and liquidus temperature. Models were also applied and methodologies developed to analyse historical blast furnace operations and determine target values.

Jan 1, 2011

By Tristan Worsey, Nathan Rouse, Kyle Hall

Drilling accuracy is the foundation to any successful blast operation. Even the best blasting practices cannot overcome poor drilling and still obtain desired results. Inaccuracies in boreholes can result in flyrock, increased vibration, uneven floor, and other undesired effects. As depth increases, variation in actual burden and spacing is expected even if collars are located precisely. Problems arise when this deviation reaches a point where it adversely affects the function of the blast design. Not only can unsafe conditions such as insufficient burden at the face develop, but poor fragmentation can compound adverse effects. As with any troubleshooting, problems cannot truly be fixed if they cannot be measured. As a result, significant work has been done in the past on this subject. Currently, there are both cheap and expensive methods used to quantify deviation for a given borehole. However, implementation of these techniques is limited. In general production blasts, little is known about the variance in designed versus true borehole geometry. This is especially true if the blaster does not see telltale signs of drilling deviation. However, losses in blast performance may exist and provide an opportunity to obtain better fragmentation and reduce fines. As drill and blast operations strive for better optimization, greater focus is being placed on drilling accuracy and solutions to this problem. The following paper details the use of several current methods for deviation measurement in order to help prevent compromises of safety and improve overall blast performance.

Jan 1, 2018

By D. Harrington

Educational campaigns conducted by the manufacturers of explosives, the Bureau of Mines, mining companies, and safety organizations have contributed greatly in reducing accidents caused by explosives arid blasting. Despite these campaigns and the dissemination of information, accidents from explosives and blasting continue to be the direct cause of scores of fatalities and hundreds of nonfatal accidents annually, not only in the mineral industry but essentially wherever explosives are used. The experience of many mining companies and other users of explosives has proved that accidents from explosives can be prevented or averted by the proper training of employees in the handling and using of explosives and by the enforcement of definite rules and instructions for their use. Unfortunately, throughout the years numerous false impressions and ideas have grown up and around the use of explosives. Many of these can be traced back to the manner in which the users of explosives were originally taught, if instructed at all; and as with many types of misinformation in nearly all walks of life, those false ideas are decidedly persistent and being so cause much damage. Many if not most of the users of explosives gained their knowledge of explosives and blasting by watching others and more or less "absorbing" the procedures and thrones of the other fellow, who acted unconsciously as teacher or instructor. A study of explosives accidents reveals the results of such "teachings" when the causes of the accidents are determined, and as might be expected the results very often are far from good. One of the most persistently erroneous impressions or ideas is concerned with the burning rate of safety fuse. Many men with

Jan 1, 1944

By Pat McLaughlin

Environmental constraints are pushing many operators to change from large rotary blastholes to the smaller diameter holes drilled with down-hole or top-hammer rigs. Productivity improvements over the years with these two drilling techniques has taken some of the bite out of the transition, while improved fragmentation and more uniform muck due to the tighter patterns can help offset increased explosives costs.

Jan 1, 1995

By J Cornejo, A Pinochet, C Caviedes

The ore extraction rate and the incorporation of new areas are key operational parameters. In massive deposits mined by caving techniques they both control the cave back geometry, which is mostly responsible for the induced stress state around productive levels. Early detection of deviations from admissible geometries will prevent stability problems related to geomechanical hazards, helping to improve safety and working conditions and reduce the potential for lost reserves.This paper describes a mine planning tool currently in use at the El Teniente mine. This tool involves the control of the cave geometry based on rules that have been defined as a result of different studies and experience collected during the operational history of the mine.This mine planning strategy achieves an extractive mining process with lower risk than conventional planning methods, ensuring ore reserves extraction if followed as planned while reducing unexpected changes in mining sequences.CITATION:Cornejo, J, Pinochet, A and Caviedes, C, 2016. Geometric control for strategic mine planning at El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 191–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Worner H. K

Education has always been a topic to rouse the interest of mining and metallurgical engineers, but the recent activities of the Education Committee of the Australasian Institute of Mining and Metallurgy 1, 2, together with the moves throughout the Commonwealth to extend the field of technological education, have made the subject a very live one at the present time. The authors have felt it would be appropriate that on the occasion of the First Ordinary Meeting for 1950, in Victoria, some contribution should be forthcoming concerning the history, present status and possible future trends of mining and metallurgical education in this State. As for the past, the time approaches when there will be none having personal recollections of the beginning of Victorian mining schools or of the men who started them. As for the future, it is obvious that rapidly expanding metal-producing and metalconsuming industries will demand a greater output of competent graduates and diplomates. The era immediately ahead seems to be bristling with opportunities, but mining educators need to temper their enthusiasm for various policies and programmes with the realisation that they are helping to train men who will be leaders 15-20 years hence when the problems of industry and trials of life generally may be very different from what they are to-day.

Jan 1, 1950

By Vincent Tirolo

The proposed Second Avenue Subway is a new two-track subway line running from 125th Street and Park Avenue at the north, east along 125th Street to Second Avenue and south along Second Avenue to the Financial District in lower Manhattan, NY with 16 new stations and 13.6 km (8.5 miles) of track. The project has been broken into four construction phases. The initial Phase 1 operating segment includes three new stations (96th, 86th and 72nd Street stations) with a connection to the existing Broadway line at the 63rd Street Station at Lexington Avenue. Rehabilitation of the 63rd Street Station is also included in the scope of Phase 1. Subsequent phases extend service north and west to 125th Street (Phase 2), south to Houston Street (Phase 3) and finally to Hanover Square (Phase 4). The DMJM Harris/Arup Joint Venture (DHAJV) prepared the Contract Documents MTA for Phase 1. Parsons Brinckerhoff is providing the MTA with construction inspection services for Contract C-26002. In April 2007, NYCT awarded first Phase 1 for $337 million to S3 Tunnel Constructors, a tri-venture comprised of Skanska USA Civil, Schiavone and Shea. Contract C26002 is for the construction of the tunnel boring ma-chine (TBM) launch box and the mining of the TBM tunnels from 92nd Street to 63rd Street. The major part of the contract is to construct a shaft, commonly referred to as the launch box, from East 92nd Street to East 95th Street having dimensions of 244-m- (800-ft-) long by 18.9-m- (62-ft-) wide and a depth of 19.8 m (65 ft), including more than 91,000 m3 (119,000 cu yd) of soil and rock contained within its walls. The launch box will ultimately become the southern half of the 96th Street Station. The focus here is geological conditions at the launch box and existing structures along the launch box. These geologic conditions and existing structures had a major influence on the selection and design of the support of excavation system (SOE), the SOE bracing system, construction staging, the ground movements, dewatering and other challenges of constructing the launch box (Fig. 1).

Jan 1, 2013

Laboratory electrical resistivity measurements of rocks are reviewed. Inductive and galvanic methods are discussed together with the ten important experimental factors which should be considered in an investigation.These experimental factors are electrodes, sample preparation, measurement errors, temporal current variations, current density, frequency, electrolyte composition, electrolyte saturation, pressure, and temperature.

Jan 1, 1969

By Wingham D. W

Based upon the previous work of Norman & Loeb, a method was used to assess the comparative wearing properties of ten different alloys being used, or being considered for use, as mill liners and grinding media at Mount Isa, The materials to be tested were obtained in the form of large diameter balls, and were run, along with the regular ball charge, in a large ball mill operating under normal grinding conditions. At selected intervals, the test balls were removed from the mill, weighed and identified, and their relative wear rates determined.INTRODUCTIONInformation in metallurgical journals, from local iron and steel foundries, and from various metal promotional organizations has suggested that the various alloy compositions available should be examined and assessed for possible use as milllfners and grinding media.Previous attempts at evaluation of recommended materials for these applications elsewhere, have usually involved the purchase of large quantities of grinding balls or complete mill liner sets, requiring running periods of up to two years or more. As well as being both a costly and lengthy procedure, the information obtained may be of little significance, due to changes in milling practice, and ore characteristics during the period of operation.To overcome these difficuities, a method was adopted based on the short time wear rate test recommended by Norman & Loeb (1949) and Norman (1957) in which all the materialsunder consideration are ·subjected·concurrently to the conditions of service.Previous calculations of wear rates have been dependent1. Senior Metallurgist (Materials), Mount Isa Mines Limited.2. Metallographer, Mount Isa Mines Limited.Manuscript received at The Institute, 22nd April, 1963, and presented to the1963 Annual Conference.

Jan 1, 1963

During a mineral exploration program in an environmentally sensitive area nearMount Painter in South Australia, a helicopter was used to position, construct and service drilling rigs in order to avoid the need to create new access tracks. The drilling program was designed to optimise the advantages of natural landforms in order to minimise the environmental impact of site construction and drilling activities. This minimisation of land disturbance reduced the required amount of rehabilitation measures to the extent where all impacts of the helicopter-supported programme had disappeared within 12 months of completion of work.

Jan 1, 1995

By M. R. Smith, H. Kanli

The impact crusher is a popular device for producing crushed aggregates from non-abrasive rocks such as limestones, offering the advantages of high reduction ratios and relatively low installed costs. To extend the application of a process-flowsheet simulator to the quarrying industry, a mathematical model of an impact crusher was therefore developed using the general crusher models of Andersen and Whiten as a basis

Aug 1, 1995