Search Documents

By Jared Ball, Darren Snashall, Paul Telford, Pengfu Tan, Ben Hogg

"The foamed converter charges were up to 3 8 per month in Xstrata Copper Smelter at Mount Isa. The issue of high converter foamover frequency had remained unsolved for many decades in Mount Isa. A thermodynamic model of copper P-S converter and a viscosity model of converter slag have been developed to simulate the slag blow and copper blow, in order to understand the mechanism of converter foamover. The model predicts the chemistry and viscosity of slag during slag blow and copper blow. The effects of oxygen potential, charge of dirty reverts, slag carryover, under-blowing, over-blowing, and temperature on the foamover and viscosity of slag in copper blow have been discussed. A theory has been developed to understand the mechanism of converter foamover. The practical solutions have also been developed and implemented in Mount Isa Copper Smelter. Some improvements of the industrial operations have been presented. After a series of improvements, the number of foamed charges per month in the converter operations has been decreased significantly from 35 in Aug 2008 to only one per month in 2009/2010.1. IntroductionThe Copper Smelter in Mount Isa receives the concentrate containing about 25% copper and produces anode copper that contains about 99% copper. There are several stages in the process. The first stage carries out in the ISASMELT™ furnace. The ISASMELT™ process produces a molten copper matte containing about 60% copper. An iron-silica slag and a sulfur dioxidebearing off-gas are the by-products of the process. The slag is taken to the slag dams for cooling before it is recycled through the Mount Isa Copper Concentrator.The matte is sent to Peirce-Smith converters. The converters further remove iron and sulphur to produce blister copper which contains about 97% copper. The anode furnaces remove any remaining sulphur and oxygen to produce anode copper that is about 99. 7% pure. This is cast into anodes and sent to the Xstrata Copper Refinery in Townsville for final refining.In the copper pyrometallurgical industrials, slag foaming is an important phenomena which occurs when the gas bubbles have stability and not rupture. Foaming greatly increases the interfacial area between matte, slag and gas and is essential for the operation of high intensity smelting processes. However, foaming or foamover is undesirable in P-S converter since it can damage the equipment and injure the operators. Figure 1 shows that the whole process of a foamover development in a converter."

Jan 1, 2011

By Zhijing Zhang

The management of hazardous wastes is important in a society which is increasingly concerned with environmental issues. Incinerators such as the slagging rotary kiln are widely used in the treatment of hazardous wastes. However, in order to assure a smooth operation of the rotary kiln, the melt should have both a low melting point and high fluidity. In this study, the fluidity of various hazardous waste rotary kiln slags was measured in terms of length of flow using the crucible test technique. It was found that the slags have melting points ranging from 1372 to 1424°C while their fluidities varied from 61-102 mm. The effect of addition of oxides on the fluidity of a slag containing 47 wt% SiO2 was also investigated. For this slag, additions of SiO2 (up to 56 wt%), FeO and Na20 increased fluidity, whereas the addition of CaO and A1203 resulted in lower fluidity values.

Jan 1, 2002

By Luciano E. Ramírez, Jesús L. Valenzuela, José R. Parga

"An innovative process for removing copper cyanide complexes including silver and zinc from cyanidation circuits has been developed. The technology was based on the inducing the nucleated precipitation of copper and silver in a tube serpentine reactor, using sodium sulfide as the precipitate and sulfuric acid as pH control. The results showed that pH had a great effect on copper cyanide removal efficiency and the optimum pH was about 3 to 3.5. At this pH value copper cyanide removal efficiency could be achieved above 97 and 99 % ,when influent copper concentration ions were 650 and 900 ppm respectively. In this process (sulphidizaton-acidification-recycle-thickening), the cyanide associated with the copper cyanide complexes is released as HCN gas under weakly acidic conditions, allowing it to be recycled back to the cyanidation process as free cyanide. This system was successfully commercial applied at Minera William in Mexico.IntroductionThe recovery of gold and silver from minerals and concentrates with cyanide is an important hydrometallurgical process, which has been studied for more than 124 years. Patented by MacArthur in 1888 [1], the process relies on the fact that gold dissolves in aerated cyanide solutions to produce the gold cyanide complex. The stoichiometry by wich this reaction occurs is known as the Elsner equation as shown here. Silver is accomplished in the same fashion."

Jan 1, 2012

By John R. Howell

"SUMMARYThe process of producing a new cast component requires significant design and development by both the design engineer and the foundry engineer. This effort strives to produce a high quality component at minimum cost. To assist in this development, an analysis system, consisting of several computer programs, has been developed to simulate the metal casting process. This system incorporates analytical geometric solid modeling, finite element analysis, results display, and an innovative technique to model the casting mold with surface boundary conditions.The simulation has produced excellent thermal results and work is in progress to develop techniques to enable use of this data in additional analyses to predict porosity and residual stress. Research is required to produce working parametric formulations of material properties. Software development is required to develop good fluid flow analyses for large. 3D models to simulate filling of and convection in molds.Integrating this system of programs is difficult due to proprietary database structures used by software developers. However, an acceptable means has been accomplished' to move data from one program to another. Further software development is required to facilitate this task. INTRODUCTIONThe process of producing a new cast component requires significant design and development by both the design and foundry engineer. This effort strives to produce a high quality, reliable component at minimum cost in a timely manner. The design engineer needs to know the physical and mechanical properites which can be expected in the actual part at critical areas. This will enable him to design a part with minimum material while fulfilling the performance required. The foundry engineer needs to produce a sound, quality casting with a minimal amount of material In risers, the feeding system and machining stock. This must be done with a minimum· investment in tooling and development time and maximum productivity of labor and capital employed. This task Is continually being made more difficult because of increased competition in the marketplace and the use of castings in more severe service. This has strongly influenced the need for high quality castings.The task of developing a new casting is difficult for both the design and foundry engineer. To assist in this development, Deere & Company has been engaged in the development of an analysis system to simulate material processes. A major portion of this program involves simulation of the metal casting process. This analysis system has evolved into a package of computer programs which simulates casting solidification and subsequent cooling through the finite element method"

Jan 1, 1986

By P. Gray

Process and engineering development of the Warner Zinc Process over the past two decades has proceeded alongside the world-wide collection and analysis of operating and cost data of current processing practices from sulphide ores to refined metals. Study of these data shows that recoveries are dependent on mineralogical characteristics of the sulphide matrix and point to the inadequacy of differential flotation as a tool for preparing feed for smelters. The paid-for return at the mine on the combined metal values in zinc rich sulphide ores rarely exceeds 80% and increasingly runs as low as 50-60%. Surveying the possible alternative ways of improving these performances leads to the conclusion that the Warner Process is the only technology in sight that could meet a target of 90% paid-for recovery and that its development has now reached a point where it can be a fully practicable process for all mixed sulphide ores.

Jan 1, 2000

By Augusto Viana Leandro Teixeira

Rare Earth Elements (REE) are fundamental for modern life products and green technologies. Supply constraints and the price peak of 2011 boosted intensive research for alternatives for processing and separation. Complex monazite- type, rare earth ores usually contain high acid consumption impurities, such as iron and aluminum, and radioactive thorium in their composition. These impurities are not removed by conventional concentration processes due to fine, micro-level association between the REE carrying minerals and the gangue minerals. This work presents a selective process route for REE extraction from iron-rich, monazite ores. The process involves sulfation by addition of concentrated sulfuric acid and pyrohydrolysis at temperatures of approximately 700–750 °C. Experimental results show REE extraction higher than 70% and low iron (below 5%) and thorium extraction (below 10%). A method based on thermogravimetric analyses was shown to be adequate to predict the behavior of a given ore sample in the sulfationselective pyrolysis-leaching process.

By Björn Saxen

Outotec atmospheric Direct Leaching has so far been implemented for zinc production capacities of around 100,000 t/a. Lately, there has been growing interest for small scale direct leaching plants, producing circa 30,000 t/a of Zn. Such small leaching plants can provide extra front-end capacity in existing roaster-based plants and enable treatment of feed materials not suitable for roasting. In small scale plants the proven OKTOP® 9000 Direct Leaching reactors are not readily applicable, due the large size. For smaller installations a modular approach is proposed providing multiple advantages, such as reducing the construction time and amount of the site work required causing less disturbance to regular plant operation with reduced cost. In this paper, we present advantages that can be achieved by using modular OKTOP®C reactors and discuss also process design when connecting a small scale direct leaching process to an existing zinc plant. Also benefits of direct leaching expansion are presented.

By Alistair Burrows

Situated in the oblast of East Kazakhstan, the Ust-Kamenogorsk Metallurgical Complex has spent the past twenty years renovating and remodelling itself as a modern polymetallic sulphide smelting facility, and a regional centre of excellence for custom smelting. Along the way there have been changes to the company structure, introduction of new technologies, investments in expanded capacity, environmental improvements, and addition of new metal products and by-products to the site’s repertoire. These changes have been gradual and incremental, but taken together they represent a significant contribution to placing Kazakhstan’s sulphide smelting industry on a strong foundation for enduring success in the international custom smelting market. In achieving these changes, a workforce that was historically isolated from much of the world now has recognised expertise, internationally competitive skills, and confidence to embrace the future. Further improvements in energy efficiency, environmental compliance and polymetallic processing capabilities are challenges that UKMC stands ready to face.

By Peter Bates

"HIsmelt has faced and overcome many challenges in the understanding and development of injection technologies that satisfy process and engineering requirements for further scale up to a commercial plant.An overview of the design basis of bottom and top injection systems with plant results are described in this paper.IntroductionAn appropriate way to introduce this paper is to initially reflect on the genesis of the HIsmelt Process.It is appropriate that Professor Womer is the one we are honouring as it can be claimed that by the involvement of CRA in the WORCRA process that the concepts for irijection systems in iron and steel pyrometallurgical processes achieved significant attention by the company. The development of water cooled injection lances and their application injecting solids and gases with success was certainly a pre-cursor to the development of other injection systems commonly used today in arc furnaces and for top injection at HIsmelt.HistOrically it was the work of Savard and Lee in Canada with shrouded tuyeres and the subsequent commercialisation of this technology at the Maxhiitte Steelworks spawning the suite of bottom oxygen blown process as known as QBOP; OBM and the subsequent combined blowing process such as KOBM that first commercially succeeded in injecting solids under a molten metal bath. The next progressive step from the injection of calcined lime in the technology development was the injection of coal for coal gasification as developed by Klöckner technologies being called KG, KSG and KMS and also the injection of coal for increased scrap melting.A paradigm shift in thought process to leap from steelmaking and coal gasification to direct smelting by injecting coal and iron ore into a molten metal bath in the correct stoichiometric ratio to maintain the bath at a constant temperature and carbon level was the true genesis .of HIsmelt.A good overview of the state of the art of tuyere type injection technology is given in Ref. 1."

Jan 1, 1996

By Bryn Harris

Chesbar Resources Inc.1 is developing a nickel-cobalt laterite project in Guatemala, Central America, by applying existing atmospheric chloride technology to a known resource. The tropical laterite project has an inferred resource of 133 million tonnes grading 1.51% nickel, which represents ~20% of Chesbar?s land holdings in Guatemala. Within its boundaries, the Sechol area has a measured resource of 14 million tonnes grading 1.46 % nickel and 0.08% cobalt, and an indicated resource of 23 million tonnes grading 1.34% nickel and 0.08% cobalt. Notwithstanding the impressive overall resource, the company has taken an innovative approach to a laterite project and is concentrating on El Inicio, a high-grade starter pit with five million tonnes grading 2.1% nickel and 0.08 % cobalt. The process flowsheet is based on atmospheric chloride leaching in a slightly acidic magnesium chloride brine, solution purification by recycled magnesia, precipitation of a mixed nickel/cobalt hydroxide intermediate product, and lixiviant regeneration by modified pyrohydrolysis technology. Initial results suggest that >90% of the contained nickel and cobalt in the non-magnetic fraction of the feed can be recovered, with <5% of the iron leaching. A metallurgical scoping study has established preliminary capital and operating costs for a production facility at a proposed rate of 20,000 tonnes per year of nickel as the intermediate mixed hydroxide. A preliminary assessment of producing a magnesium oxide by-product has also been carried out. This paper reports on the current development of the project and highlights the advantages of working in a chloride medium at atmospheric pressure and slightly elevated temperatures.

Jan 1, 2003

By Samuel Senanu, Benjamin Agyei-Tuffour, Lifeng Zhang, Eivind Øvrelid, Adegboyega Nathaniel Femi

"The solar grade silicon ingot produced from directional solidification process usually pushes the impurities to the top and finally cut off and discarded, which leads to material loss. The hard inclusions lead to wire breakages during the cutting of the ingot in wafers. The main kinds of inclusions found in solar grade silicon have been investigated using vacuum filtration: needle-like Si3N4 and lumpy SiC inclusions. Clusters of SiC inclusions and Si3N4 are also found. Surface observations of the scraps before polishing reveals that Si3N4 inclusions are usually bigger and in some cases can be about a few millimeters. SiC inclusions are usually smaller, ~200µm but can be ~500µm in some cases. Inclusions observed after filtration are mainly SiC with diameters ~10µm. Through the vacuum filtration, 99% inclusions can be removed 99%. The possible mechanisms of filtration are cake filtration for the larger sized Si3N4 and SiC inclusions and deep-bed filtration the SiC inclusions. For the directional solidified silicon ingot, an approximate distance of ~10mm gave an encouraging cutoff thickness. The inclusions sizes were below 10µm. Introduction The search for an alternative source of energy to fossil fuel has led to a dramatic increase in the demand for solar energy due to its high dependability (abundant in nature) and environmental friendliness 1). During the last 5 to 10 years, the annual worldwide production of solar cell by the photovoltaic industry has increased to an annual rate of 30 to 40 percent 2). A necessary condition for the maintenance and even an increase of this growth rate is a decrease in the cost of feedstock for the solar cell production 1). The total international production in 1997 was 130 MW worth more than $500 million. In 2004 the consolidated world total production of PV cells increased to 1146 MW or around. $7 billion (Figure 1) 3). Silicon is currently the most dominant semiconductor material used in the PV industry. As shown in Figure 2 3), solar cells consist of two types of material, often the p-type and n-type silicon. Light of certain wavelengths are able to ionize the atoms in the silicon (causing atoms to either gain or lose electrons) and the internal field produced by the junction separates some of the positive charges (“holes”) from the negative charges (electrons) within the photovoltaic device. The holes are swept into the positive or p-layer and the electrons are swept into the negative or n-layer. Although these opposite charges are attracted to each other, most of them can only recombine by passing through an external circuit outside the material because of the internal potential energy barrier. Therefore if a circuit is made, power can be produced from the cells under light because the free electrons pass through the load to recombine with the positive holes."

Jan 1, 2008

By Robert Corson

Zinc has a large solubility in Fe and a completely filled ?d? shell. With the discovery of dramatic increase of the magnetostriction in Fe by Ga addition, an examination of element Zinc that is adjacent to Ga in the periodic table is of significant interest. In this work, the effect of binary alloying of Zn with Fe on the magnetic and magnetostrictive properties is examined. The FeZn alloys were processed using powder metallurgy and vapor phase synthesis, and Zn contents were varied from 5% to 30%. An examination of the influence of different processing parameters and the Zn content on the resulting alloy properties is presented. The alloys were characterized using X-ray diffraction and SEM. Magnetostriction measurements were carried out at different pre-stress levels. Magnetic properties were measured using a vibrating sample magnetometer.

Jan 1, 2006

By Norbert Patzeh

The demand for nickel is growing and will continue to do so for the foreseeable, future. This will make the construction of new leaching and smelting plants necessary. This paper described a number of possible alternative processes. The first projects with new technology are currently undergoing trials and feasibility studies. Experience from other industrial sectors and from existing plants is being incorporated into these investigations. The question is, to what extent the old nickel producing concepts will continue to be applied in the future. Keywords: Latcritc, rotary kiln, cyclonc rcactor, dust processing

Jan 1, 2004

By S. Yin, A. Bogno, H. Henein, P. Natzke

Impulse Atomization (IA) (a single fluid atomization technique) was used to rapidly solidify Al- 4.5wt%Cu and Al-4.5wt%Cu-0.4wt%Sc under argon atmosphere. In addition to the IA-generated droplets, the same technique was used to produce strips by Spray Deposition (SD) of the same alloys on a copper substrate with and without oil coating. The rapid solidification microstructures were analyzed using Scanning Electron Microscopy (SEM). From the SEM images, the amount of eutectic and the secondary dendrite arm spacing (SDAS) were measured. These SDAS results lead to the estimation of cooling rate. The eutectic fraction coupled with the metastable extension of the solidus and liquidus lines of Al-Cu (Sc) phase diagram lead to the estimation of primary and eutectic undercoolings. A comparison of the solidification path of the droplets and the strips was done as well as the analysis of the effects of scandium.

Jan 1, 2015

By Neale R. Neelameggham

"Most chemical process plants and metallurgical production facilities have some sort of cogeneration to minimize process energy costs. Use of Alternative Energy Production from sun and wind power with storage can become an integral part of a process plant utility. This will facilitate reduced fossil fuel usage and help minimize thermal emissions. This will be similar to Pollution Control equipment, which have become an essential part of process plants in the past four decades. Conceptual flow sheets of such Process Utility schemes are presented.IntroductionPower is supplied to industries, commercial and residential users. Over the past decade, Electric Utility companies have made major inroads, in introducing alternative energy resources in an attempt to somewhat reduce fossil fuel use in power generation. Now, on a much larger scale than in the early 1980s, residential users, motivated by government provided tax credits, have started installing alternative energy generators such as roof top wind mills or roof-top photovoltaic generators. This will minimize future energy costs, help control thermal emissions etc. This alternative power generation is typically connected to the existing power grid with two way power metering. However, the use of alternative energy generation has not been seen at large industrial sites yet.Paul Scherer Institute, Switzerland and the NREL laboratories in Colorado, are two of the several institutes which have been developing how solar thermal power can be used to supply the endothermic input energy in chemical and metallurgical processes. The theme of this present symposium addresses the above as well as the energy storage needs for such events to become continuous. This paper emphasizes the concept of how alternate energy can be used in the production of materials on a generic sense wherever there is a need for input energy – beyond endothermic process energy - while addressing how to reduce the thermal and carbon emissions.The alternative energy generation using wind or solar source is discontinuous due to the nature of the energy source. They are not only discontinuous but also variable. This necessitates storage of generated power for close to continuous use with variable loads. C Smith, et al pointed out in 2006, that 'the electric power industry has taken notice of the expansion of wind and its potential' in a summary article on integrating wind generation into utility systems.1 In 2009, the 1000 MW wind generation project in Texas had to be postponed to 2013 for lack of transmission.2 There are only a few large MW solar generation units in the US; the projects being slow mainly from lack of adequate storage and redistribution."

Jan 1, 2010

By Ana E. Bohé, Georgina De Micco, Gastón G. Fouga

"In this work the reaction between several manganese oxides and chlorine is investigated in the range of temperatures between 650 and 950ºC. The reaction path for the chlorination of MnO is established, which involves recrystallization of high valence manganese oxides (Mn3O4 and Mn2O3) followed by its chlorination. For this reason, to understand the reaction of MnO, the chlorination of Mn3O4 and Mn2O3 has also been studied. The starting temperature for the reaction of these oxides is determined by non isothermal thermogravimetric measurements. The effect of temperature is analyzed, under our experimental conditions the rate of reaction is mass transfer controlled. The activation energy for the volatilization of manganese chloride is obtained which is in good agreement with volatilization enthalpy of MnCl2.IntroductionMany oxide ores which have manganese in their composition undergo chlorination processes during the extraction of refractory metals such as Ti, Hf and Nb. Although several works related with chlorination of manganese oxides were reported, there is no information about the kinetics or mechanism of the manganese oxide chlorination reactions. Okahara et al. studied the chlorination of manganese oxides and established that they react easily above 250ºC. Furthermore, they observed that chlorination of high order oxides is more difficult when there is not a reducing agent [1]. Ivashentsev studied the chlorination of manganese oxides using Cl2(g), CO(g) + Cl2(g) and COCl2(g). He established that the reaction of MnO started at 130ºC with formation of MnCl2(s), he also observed recrystallization of manganese sexquioxide [2]. Finally, the chlorination of manganese nodules from the ocean was studied by Murthy and Reddy [3] with the aim of obtaining valuable metals such as Mn, Co, Ni and Cu. They studied the influence of several parameters like temperature, carbon percentage, particle size and chlorine flow rate in the extraction process."

Jan 1, 2008

By Andreas Siegmund

Cast or rolled lead anodes employed in zinc electrowinning typically contain between 0.5?1.0% silver to decrease the overall corrosion rate. The production of cast lead-silver or lead-silver-calcium anodes often results in the formation of numerous holes, voids or laps in the anode surface that can initiate internal corrosion in localized areas. In rolled anodes the presence of internal porosity is significantly reduced, thus resulting in extended service life. The obtained grain structure of cast or rolled Pb-Ag anodes, however, requires a relatively long period of time to form a stable protective PbO2/MnO2 layer that can evolve oxygen without excessive lead contamination of the cathode. Therefore, these anodes are often mechanically, chemically or electrochemically conditioned prior to being placed in the electrowinning process. RSR Technologies has developed an improved anode for zinc electrowinning. The anode consists of a rolled Pb-Ag-Ca-alloy with controlled surface grain structure. The preferred calcium and silver content of the alloy is 0.05?0.08 % and 0.3?0.4%, respectively. Since May 2001, industrial-scale tests have been carried out at two zinc refineries in North America in industrial electrowinning cells. The controlled grain structure of these anodes allows forming an adherent protective oxide coating within a short period of several days when placed in an electrowinning cell without the necessity of being preconditioned. Anode sludge growth is evenly distributed. The anodes stay dimensionally stable and no short-circuits have been observed. Consequently, low corrosion rates and improved current efficiencies have been achieved.

Jan 1, 2003

By Oleg Ostrovski

Industrial pyrometallurgical processes in ferrous metallurgy are based on carbothermal reduction of metal oxides. Carbothermal reduction of stable oxides requires high temperatures. Lowtemperature reduction can be implemented by using methane-containing gas with high carbon activity, or by carbothermal reduction under reduced CO partial pressure. Under standard conditions, methane is thermodynamically unstable above 550 °C and decomposes to solid carbon and hydrogen. At appropriate CH4/H2 ratio and temperature, carbon activity in the methane-containing gas phase can be well above unity relative to graphite, which provides favorable thermodynamic conditions for reduction. To maintain these conditions, the rate of reduction/carburisation should be higher than the rate of solid carbon deposition. The paper discusses reduction of pure manganese and chromium oxides at relatively low temperatures, and constraints in reduction of manganese and chromium ores. Reduction of metal oxides by carbon in hydrogen as an alternative use of natural gas is also discussed.

Jan 1, 2014

By R. Craig McClung

Contrary to other sulfide minerals, where recovery is principally liberation controlled, the recovery of molybdenite is more complex. It is this complexity that initiated a geometallurgical investigation of molybdenites from Bingham Canyon. The aim of this investigation was to determine the effect mineralogy and/or mineralogical attributes have on recovery. All samples were analyzed using normal mineralogical techniques. The results reveal the presence of two distinctly different types of molybdenite. These have been identified as the two polytypes of molybdenite: i.e. hexagonal (2H); and rhombohedral (3R). The 2H-polytype occurs as textbook-shaped particles in quartz-molybdenite veins that are located in the current pit bottom. The 3R-polytype occurs as disseminated, “ball”-shaped particles with a dull or frosted appearance and are concentrated along the margins of the current pit. Concerning their metallurgical behavior, each type exhibits unique metallurgical properties that are consistent with those reported in the published literature. The 2H-polytype is easily ground and kinetically “faster” floating with surface attributes that are amenable to higher rates of recovery. This results in the production of a high quality concentrate under normal operating conditions. The 3R-polytype, by comparison, is difficult to grind and kinetically “slower” floating with surface attributes that are less amenable to recovery. Therefore, in deposits with higher concentrations of the 3R-polytype, modifications to the normal operating parameters may be necessary to improve recovery. This investigation highlights the necessity for understanding the mineralogical characteristics of any economic mineral(s), as these will have a direct impact on recovery.

By Patrick R. Taylor

A kinetic study of the fluosilicic acid leaching of galena was performed under the presence of different oxidants. Fluosilicic acid concentration, agitation speed, concentration of solids and particle size, type and concentration of oxidant, and temperature were the variables studied. Hydrogen peroxide was found to be the most effective oxidant, its effectiveness being proportional to its concentration. As expected, an increase of leaching temperature increased the overall extraction and extraction rate. The same was found by decreasing the galena particle size. It is thought that leaching using hydrogen peroxide is controlled by fluid film mass transfer due to the calculated apparent activation energy. Reaction by-products such as sulfur and sulfur compounds retard the leaching rate. A mathematical model is proposed and compared to experimental results.

Jan 1, 2003