Search Documents

By M. J. Bagshaw, J. D. Hunt, R. M. Jordan

"Continuous casting processes, and the roll casting process in particular, offer considerable potential to the Aluminium industry, both meatallurgically and economically.The three major limiting process problems that occur during roll casting are Centre Line Segregation', 'Sticking' where metal adheres to the rolls during casting, and 'Heat Line' formation. 'Heat Lines' are localised semi-continuous longitudinal defects, usually a few cms in width, where the cast metal leaves the roll bite partially molten. These defects occur at relatively low casting speeds when the mean slab exit temperature remains several hundred degrees below the solidus temperature. The objective of the work described here is to develop a better understanding of the roll casting process in general, and in particular, to understand the phenomenon of 'Heat Line' formation.A steady state two dimensional finite difference model has been developed to describe the roll casting process, incorporating a variable heat transfer coefficient through the roll bite. In the model the difference equations are formulated using a control volume method and latent heat is incorporated according to the Scheil equation. A Gauss-Seidel type technique is used to obtain the solution. Because the rate of heat evolution is non-linear the temperature in each box is determined by using a Newton-Raphson method. The solution for a box can be multi valued and therefore lead to instability particularly near the vicinity of the front. A stability 'criterion is presented which shows that to obtain a stable solution it is better to have long narrow boxes rather than boxes with small dimensions in both directions.The model explains why heat lines form in terms of the variable slab/roll heat transfer coefficient.Experimental measurements of slab exit temperatures are also presented. These were obtained on a Hunter twin roll caster for the binary AI-Cu system, at two compositions over as wide a range· of casting speeds as possible. The experimental results are compared with the predicted ones."

Jan 1, 1986

By J. Brent Hiskey, Rebecca Grace Copp

The solvent extraction of yttrium and neodymium from copper pregnant leach solutions (PLS) using Primene JM-T, a primary aliphatic amine, has been studied. Effect of contact time, pH, sulfate concentration, and extractant concentration were investigated using synthetic and actual PLS systems. Standard experimental conditions were 5 minute contact time, pH ~2.5, and 10 % v/v Primene JM-T concentration. Distribution isotherms were constructed for the pure systems and for actual copper leach solutions. Synthetic solutions contained 100 ppm Y and ~75 ppm Nd. Samples of PLS contained 2 - 10 ppm Nd and 14 - 30 ppm Y. Results showed that complete extraction of both yttrium and neodymium occurred within five minutes and at pH values greater than 1. It was also found that sulfate concentration does not inhibit extraction at any concentration. Additionally, the distribution isotherms created show that extraction for these metals can operationally take place in one stage.

Jan 1, 2016

By Haydar Güneş

In this study, a hydrometallurgical process was evaluated for the recovery of Nd from a Nd-Fe-B magnet. Each leaching test was performed at the solid (weight) to liquid (volume) ratio of 1:50 and was mixed at 400 rpm at ambient temperature. The effects of 3 different acids (HCl, HNO3, and H2SO4) on the extraction of Nd were investigated and H2SO4 was found to be more effective than other acid solutions. Under the optimal conditions, pregnant leach solution was produced with H2SO4 for subsequent Nd precipitation testing. Each precipitation test was carried out using 100 mL of feed solution mixed at 600 rpm at 25°C. NaOH and H2C2O4 were used for Nd precipitation. The highest Nd was precipitated as Nd2(C2O4)3, 10H2O with C2H2O4 at 20 min.

By Tuula Mäkinen

In 1959 Outokumpu started up an integrated nickel smelter and refinery at Harjavalta. The flash smelting ? Peirce-Smith converting route was applied, and the high-grade converter matte was further refined to nickel cathodes by leaching and electrowinning. In 1995 the production capacity was increased from 17 000 mtpa to 52 000 mtpa, based on the Direct Outokumpu Nickel Smelting Process. The additional refinery capacity is based on hydrogen pressure reduction, producing nickel powder and briquettes. The smelting operation is currently part of Boliden Group and the nickel refinery part of OM Group. In the DON technology, high-grade nickel matte with low iron content is produced in the flash smelting furnace directly without subsequent converting. The metal values in the smelting slag are recovered in an electric furnace as an iron containing Ni-matte. The mattes produced differ from the conventional nickel mattes in many respects, and therefore focused R&D efforts have been made in order to cope with their melting points, fluidities and settling properties. When developing and operating metallurgical processes it is crucial to manage and control the characteristics of the products as well as by-products generated in different steps of the process chain. The low melting points of the high-grade nickel mattes produced in the DON furnace, particularly those low in copper, have pointed out challenges in the furnace design, in particular in the hearth and its thermal engineering. Also key issues of the DON technology are smelting of high-magnesia concentrates, the recoveries of nickel and copper, as well as those of PGM`s and cobalt. These factors can be affected by a proper selection of the process concept, and the operational conditions in the processing vessels. This paper deals with the experience of the DON technology gained over the first ten years of operation, including the significant environmental impacts. Selected results of the thermo-dynamic modelling of DON and EF mattes and high-magnesia slags are reviewed, with the reference to the mattes produced. Also the design principles of the FSF and EF will be discussed.

Jan 1, 2006

By Kyle S. Brinkman, Kenneth L. Reifsnider, Fazle Rabbi

"Mixed ionic and electronic conducting (MIEC) ceramic membranes are HeteroFoaM's which play an essential role in a number of energy conversion related systems including the solid oxide fuel cell (SOFC), oxygen separation and permeation membranes, partial oxidization membrane reactors for natural gas processing, and high temperature electrolysis cells. Dual phase oxygen membranes consisting of an ionic conducting phase Ceo.sGdo.z02 (CGO) and an electronic conductive phase C0Fe204 (CFO) were fabricated and characterized by structural (XRD), microstructural (SEM-EDS) and broadband dielectric measurement techniques. In-situ measurements of the dielectric properties of working oxygen separation membranes are presented which indicate that the material's dielectric behavior can be an indicator for MIECperformance.IntroductionCeramic membranes which transport oxygen ions play an essential role in a number of energy conversion related systems including the solid oxide fuel cell (SOFC) [l ], oxygen separation and permeation membranes in the commercial and nuclear arena [2, 3], partial oxidization membrane reactors for natural gas processing [4], and high temperature electrolysis cells [5]. For the electrolyte functions, the membranes must transport oxygen ions only. On the other hand, permeation membranes, typically used in combustion devices to support oxy-fuel combustion or for partial oxidation reactions involving the production of synthesis gases, require mixed oxygen ion and electronic conduction (MIEC). Traditionally the tailoring of the ratio of ionic conductivity to the materials electronic conductivity, measured as the transference number, has been accomplished by the introduction of aliovalent doping elements creating point defects in the material facilitating the diffusion of charged species. However, several decades of research have not yet produced single phase materials which possess the concomitant ionic and electronic conductivity required for use in membrane separation applications. It is clear that novel ""dual phase"" heterogeneous materials will be required and that the surface reactions of these materials will be of particular importance as the industry moves toward thin films membranes [6]."

Jan 1, 2013

By Yong Hack Lee

Nonferrous smelting processes have been through a rapid transformation since the beginning of 1980. The copper smelting technology has changed from the conventional Blast Furnace process to the Flash Smelting and MIB process. In the field of lead smelting, the technology has changed from the Blast Furnace Smelting to the Direct Smelting such as QSL and KIVCET. In 1992, Onsan Refinery successfully commissioned Direct Smelting QSL technology for lead. The QSL could produce more than 160,000 ton per year of lead bullion from lead concentrate and various residues. Moreover, since the year 2000, the TSL (Top Submerged Lance) Technology utilizing the same Direct Smelting process has been successfully commissioned to treat lead concentrate as well as lead sulfate residue produced from a hydrometallurgical zinc plant. This paper presents and compares the energy flows of lead smelting processes such as a conventional process and the Direct Smelting Processes plotted on the Pb-O-S phase diagram. The oxygen potential diagram suggests how to control the oxygen potential in the furnace. Also, it describes the recent operational experience in the TSL plant of Onsan Refinery with necessary mass balance of key elements.

Jan 1, 2003

By Cesar O. Gomez

A procedure has been developed for mounting at random particles of mineral samples to be characterized using image analysis. The procedure is based on the generation of a random distribution of sample particles in particles of a diluent material. and the embedding of this particle mixture in an epoxy resin without disturbing the initial distribution. Two materials with atomic number similar to that of the epoxy resin were successfully used as diluents: activated charcoal and graphite. The proportion of diluent material to be mixed with the sample to have a large number of mineral particles in the field of view while keeping the occurrence of touching particles at an acceptable level was determined empirically. The randomization achieved with the procedure developed in this work was tested using as samples known mixtures of silica and pyrite particles of the same sieve class. The agreement obtained between the mass ratio of minerals used in the preparation of a particular specimen and that resulting from image analysis demonstrates that the procedure developed is successful in producing a specimen where the embedded particles are randomly distributed.

Jan 1, 1988

By Gabriel Plascencia

Copper was oxidized in the temperature range from 300 to 1000 GC under different pressures of oxygen. In the range from 300 to 500°C, copper oxidizes following the logarithmic rate law; while in the range from 600 to 1000°C oxidation follows the parabolic rate law. Transition from logarithmic to parabolic growth occurs at about 525°C. X-ray diffraction was performed on oxide scales to account for the CuO/Cu2O ratio at different temperatures. Activation energies found in this work are in good agreement with reported values.

Jan 1, 2003

Acid generation from reactive sulphide mineral tailings has become a major environmental problem in the mining industry. Initiation of chemical and biochemical oxidation reactions of the sulphide mineral leads to acid generation. A novel concept of safe disposal and utilization of reactive fine mill tailings is presented in this paper. The paper also presents the results of a preliminary laboratory experimental .study of the concept. The tailings are agglomerated using portland cement as a binder. The cold bonded agglomerates are encapsulated with other chemical additives to act as acid neutralizers, oxygen and ironoxidizing bactericides., The primary. factors influencing the choice of bacterfoides to inhibit the acid generating bacteria are their costs, toxicity and environmental friendliness. The paper discusses the utilization of agglomerated' products as aggregates for underground backfill, or as gravel for surface land cover.

Jan 1, 1991

By F. G. Caballero, J. L. Gonzalez-Carrasco, S. Barrius, H. Carreon, M. Lieblich

"The grit blasting is a low-cost technique successfully used to enhance mechanical fixation of the implants through increasing their roughness. As a result of the severe plastic surface deformation, it produces subsurface effects such as grain refinement, hardening and compressive residual stresses which are generally evaluated with destructive techniques. In this research work, non-contacting and contacting thermoelectric power measurements are performed in blasted 316L VM and Ti-6AI-4V specimens using Ah03 and Zr02 particles which yield a coarse and a fine rough surface, respectively. This study correlates the microstructural changes induced by the grit blasting treatment and the limitations and advantages of each of the nondestructive thermoelectric techniques based on the Seebeck effect used to evaluate these biomaterials.IntroductionIt is well known that surface properties play an important role in metallic materials used in bio-medical applications. Since the biological response is correlated directly with surface properties it is comprehensible the intense activity in superficial modification by physics or chemistry methods in this field. Grit blasting, one of the most popular surface modification of metallic biomaterials, enhances the mechanical fixation of the implant through the increase in roughness [1-3]. Roughening is developed by bombarding the surface with a high-velocity jet of ceramic particles, being the final roughness a function of the processing parameters (pressure, distance, time, ... ) and blasting particles (nature, shape, size). As the plastically deformed surface layer tries to expand relatively to the intact interior of the specimen, residual compressive stress gradients develops perpendicular to the surface at shallow depths with a maximum value at a depth in the range of 5 to 60 µm. This surface treatment also may cause subtle variations in the subsurface material properties, such as increased hardness and grain size refinement, which are consequences of the significant plastic deformation through cold work. Blasted affected zones may extend to a depth of up to about 200 µm. The subsurface hardening and the near-surface compressive stress gradient playa beneficial role by retarding fatigue crack nucleation and further growth, ultimately extending the fatigue life of the metallic part [4]. In this work, two non-destructive thermoelectric techniques (NDTT), the non-contacting and contacting thermoelectric power measurements were used to analyze the subsurface induced changes on blasted Ti-6AI-4V and 316L VM specimens using Al2O3 and Zr02 particles. Detailed information on the microstructural induced effects and subsurface mechanical properties were published elsewhere [5-8]. Here the nondestructive evaluation of the involved microstructural changes is used to assess the global subsurface damage. Advantages of using nondestructive techniques during manufacturing are envisaged."

Jan 1, 2012

By Fatma Arslan

The lateritic nickel ore sample subjected to this experimental study was taken from Çalda ore deposit (Turkey) and contains 1.43% Ni and 0.105% Co. Mineralogical investigations showed that the ore sample contains asbolane, chromite, limonite, hematite, goethite, lepidocrocite, magnetite, serpentine, and clay type minerals together with chalcedon, quartz, calcite, and chlorite. In the acidic leaching experiments, the effects of temperature, acid (H2SO4) concentration, and leaching time on nickel leaching recoveries were investigated. Leaching recovery versus time curves showed a parabolic trend and increasing the temperature shifted that curves to the higher values. The dissolution of nickel from lateritic ore can be explained by a shrinking core model and the apparent activation energy was found as 47.34 kJ/mol in the range given by the literature. The highest Ni and Co leaching efficiencies as 90.2% and 96.8% respectively were obtained at 80°C temperature, 200 g/L H2SO4 concentration, and 8 hours of leaching time.

Jan 1, 2006

By Gretel Parker

In situ Raman spectroscopic investigations of copper iron sulfides in leach solutions have been undertaken. Coupling potentiodynamic techniques to Raman spectroscopy produces a powerful tool for studying mineral surface response to changing conditions, while ESEM and high-vacuum techniques provide complementary ex-situ information on surface structure and composition. Oxidative acid leaching of chalcopyrite at ambient temperature yielded a product with S-S bonds that were shifted from those seen with covellite, with little evidence of elemental sulfur formation. Leaching of chalcopyrite led to non-homogeneous product distribution. Raman spectroscopy was able to identify the products formed on the mineral surfacein situ while leaching was occurring. Raman mapping and imaging demonstrated a surface distribution of the products which can be related to composition and structure changes of the mineral surface. The surface formed on chalcopyrite after anodic oxidation at 0.570 V vs. Ag/AgCl in 0.1 mol dm-3 HCl undergoes laser-induced transformation.

Jan 1, 2003

By A. V. Tarasov

In order to improve technical, economic and environmental performance of hydrometallurgical processing of intermediate products containing copper and nickel, the Gintsvetmet Institute and the IMET Institute of the Russian Academy of Sciences have conducted studies into the efficiency of the use of alternating current of industrial frequency on processes applied for hydrochemical leaching of various copper- and nickel-containing materials. It has been found that: 1.Imposition of alternating current over the process of leaching of softly reduced nickel oxide with recycled copper sulfate solutions resulted in an increase by 20 to 30% of the rate of the copper cementation process and reduced by 20% its activation energy. At the same time, the recoveries of nickel, cobalt and iron to the leach solution increased up to 82.2%, 78.5% and 57.1%, respectively, and that of copper to the cement precipitate up to 74%. Optimal process conditions have been identified with respect to the current density, electrode material, copper concentration in solutions and the process temperature. 2.In the process of hydroelectrochemical sulfuric acid leaching of nickel and copper sulfides, the grain size, the phase form of sulfides, the solution composition (H2SO4, Cl?, Cu2+, Fe3+)and the current amperage had an effect on the nickel recovery to the solution, which reached 90%, while the degree of copper transfer to solution did not exceed 20%. The process of hydroelectrochemical sulfuric acid leaching of nickel and copper sulfides with an addition of Cl? made it possible to selectively recover nickel into the leach solution along with concentrating copper in the leach residue. 3.When subjecting samples of commercial-grade magnetic fractions of converter matte to sulfuric acid leaching, the imposition of electric current, the concentrations of sulfuric acid and chloride ion in the solution and the duration of the reaction process had an effect on the process. The nickel recovery was 85% and that of cobalt and iron was 95% and the recoveries reached 97.5%, 98.3% and 99.8% as a result of repeated treatment of the primary residue under similar process conditions. Up to 75% of copper, 75% of sulfur and 99.0-99.5% of palladium was concentrated in the solid reach residues. The experimental data obtained indicates that the use of AC for hydroelectrochemical sulfuric acid leaching for separation of copper- and nickel-containing intermediate products has favorable prospects.

Jan 1, 2003

By Cz. Mazanek

Specific biostimulating and anticancerous properties have been observed in peat, Ash Vacanta, and in an amorpous silica that is obtained as a by-product of alumina production from Turow clay in Poland. The anmphous silica was characterized and found to have a large specific surface area. This property may account for the beneficial characteristics of the material.

Jan 1, 1989

By K. Ono

A new process for extraction of titanium metal from its oxide is demonstrated. In this process, row material to be reduced is titanium oxide synthesized from ilmenite. The reducing agent is the Ca+CaCI2 two-phase mixture. TItanium is elaborated in the medium consisted of liquid Ca, Caq and solid TI02 at the temperature range 1200 to l300K by means of mixing mechanically the ingredients in the reactor into a smooth paste. Fluidity of the feed which enables continuous scheme depends on the CaCl2 content. The oxygen level of the reduced titanium is the range 500 to 1000 mass ppm varying with the operational conditions. The Ca+CaCI2 reducing agent is taken out from the electrolysis of CaC12 at 11401(, and this CaCl2 is produced by aqueous chemistry conversion using Cl2 gas recycled from the electrolysis.

Jan 1, 2001

By Donald R. Sadoway

The viability of treating certain forms of hazardous waste by direct electrolysis in molten oxides is under investigation. Secondary residue or waste mud produced in the course of chromate chemical production is the focus of attention in this study. The goal is to reduce the water soluble hexavalent chromium either to insoluble trivalent chromium or to chromium metal. Electrolysis tests have been conducted in a high temperature cell containing chromate sludge dissolved in an electrolyte composed of Al2O3, SiO2, CaO, and MgO. Oxygen production on a carbon-free anode has been confirmed.

Jan 1, 1992

Designing rigging systems for complex castings has been more of an art than a science. Foundrymen have used thumb rules based on past experience to develop working designs. Of late, attempts are being made to formalize the procedure through the use of rule based expert systems, process modeling and other tools. Designing risers is one of the challenges of the rigging system design. Once the riser location have been determined, an optimization technique coupled with a casting simulation code can be used to determine the optimum riser dimensions. The main drawback of using a finite element or a finite difference based process simulation code along with the optimization routine is that the computation time involved is too large. Such an approach, thus, is unrealistic for practical situations where different options have to be explored and conclusions drawn in a short period of time. This difficulty has been avoided in the present work. The optimization scheme has been coupled with a modulus based solution routine to optimize the riser dimensions. The modulus calculations provide a good and quick estimate of the freezing time at different points in the casting. A functional, obtained from these freezing time values, is minimized by altering the dimensions of the riser until an optimum shape is obtained. Some examples have been included to illustrate the utility of this technique.

Jan 1, 1994

By Ying Mao, Zhancheng Guo, Long Ma, Huiqing Tang

"A new 2D computational fluid dynamic (CFD) model was developed for the gaseous reduction of iron ore fines in an innovative reactor-multilayer moving-fluidized bed. The solution of the proposed model was performed by integration of FLUENT and PHOENICS. Numerical results of cold state were compared with the experimental data and the agreement between them was good. A hot case-gaseous reduction of iron ore fines using syngas with this reactor was simulated using the present CFD mode. Results indicate that under the given simulation conditions, total pressure drop is 90 Pa less than that under cold state though the gas supply rate is increased about 4m3 under hot state. Gas temperature decreases from 1073 K at the bottom to 500 K at the top, Utilization efficiency of the gas reduction potential is about 27 %. For ore fines reduction, the final reduction fraction could reach 0. 70 and solid temperature 900 K.IntroductionWith the development of coal gasification technology, various coals could be converted to Syngas with air or steam. Therefore gaseous reduction of iron ore fmes becomes an acceptable alternative process for iron making besides blast furnace route[!] and moreover it still has some advantages in processing low grade iron ore fines[2]. Gaseous reduction using fluidized bed technologies is the most competitive in all direct reduction iron-making processes up to now. It has the advantage that ore fines can be directly charged to the process without prior treatment while its disadvantages are particle agglomeration and high gas/solid ratio[3]. To avoid these advantages, a new reactor, multilayer moving-fluidized bed reactor has been developed for carrying out the gaseous reduction. Hydrodynamic behaviors of gas and fines in the reactor were studied and the results were satisfying[4]. However, due to its unique structure of the multilayer moving-fluidized bed and unique gas-solid flow pattern, models of multiphase flow as IPSA, DPM and Eulerian Model could not give a satisfying solution. The current paper is developed a new CFD model and a new solution approach for simulation of the reactive gas-solid flow in the multilayer moving-fluidized bed for its optimization, design improvement and future scale-up."

Jan 1, 2013

By F. Sakurai

The enlarged Mitsubishi process in Naoshima has been in steady operation since. May 1991. However, the sulfuric acid plants have been in operation for more than 30 years. The acid plants were modernized between 1999 and 2001 by renewing some of main equipment such as the drying tower and gas heat exchangers, and introducing new technology. At the same time, as an electric energy saving measure, the electric power consumption in the sulfuric acid plant was vastly improved by decreasing the volume of gas treated the installation of low temperature activity catalyst in the 1st pass of the converter and optimization of main gas blower runner. Furthermore, last year, the oxygen plant was replaced and enlarged, and anode production increased from 240,000 to 280,000 tonnes per year with an associated increase of sulfuric acid from 550,000 to 660,000 tonnes per year. This paper describes these recent improvements in the acid plant at Naoshima smelter.

Jan 1, 2002

By F. G. Prado

The technology for the extraction of zinc from zinc residues, such as zinc ashes, drosses and metallurgical flue dusts, by way of ammonium chloride solutions is well established, at least at the laboratory and bench scale levels. (3, 4) Zinc is soluble in ammonium chloride solutions in the form of zinc diammine chloride. Its solubility depends upon the concentrations and temperatures employed. The procedure and the equipment required are simple, and they can be applied either to small or large operations. As a by-product, zinc diammine chloride is produced with extremely low impurities in quantities which are stoichiometrically proportional to the zinc removed. The technology has been applied experimentally to galvanized steel residues. The dezincing results, including removal performance, energy and reagents required, and by-products are summarily presented in this paper.

Jan 1, 1992