Search Documents

By Batric Pesic

Gold dissolution with bromine was studied by using the rotating disc technique. Geobram TM 3400 was used as a source of bromine. The parameters studied were: rotating speed, Geobrom 3400 concentration, pH, temperature, sulfuric and hydrochloric acid concentration, and the concentration of various cations (copper, iron, zinc, aluminum, manganese, potassium and sodium) and anions (chloride, bromide, sulfate, nitrate, and iodide) According to the Levich plot and activation energy, gold dissolution was controlled by a chemical reaction rate. Copper, iron, and manganese in their highest oxidation states, aluminum, zinc, sodium and potassium did not have any effect on gold dissolution rate. The presence of manganous ion dramatically decreased the gold dissolution rate. Kinetic performance of bromine, in the form of Geobram TM 3400, was compared with performance of cyanide and thiourea.

Jan 1, 1990

By Kunihiko Takeda, Kimio Imaizumi, Tsuyoshi Arai

"The study on the preparation of mono-dispersed liquid droplet was performed using ultrasonic as one of the steps of producing the perfectly mono-dispersed particle. The ultrasonic system was a 33.6kHz ultrasonic generator, an amplifier, an electric distortion element, and a bolted Langevin type horn installed in .a cell. For the first time, a liquid pillar under a nozzle of the cell ·was stably formed. Then, dense and coarse parts were alternatively constructed by oscillating the wavelength of the ultrasonic.· The diameter of those liquid droplets were found to be· perfectly uniform, therefore, it was measured by ""multiplex photography"" using a synchronized stroboscope with the ultrasonic.- From the results, more than 30,000 of perfectly uniform liquid droplets in 1 second were observed by this method.IntroductionRecently, research on the control of physical form is done in various fields of industry. Some examples are the processing technology of the minute compound material of micro-machines and integrated circuits, and the form control of molecule size like catalysts. There is a need for such material to take on various forms in correspondence to its use. ""Form control"" as used in this study will indicate ""research on physical chemistry factors which determine the size of the material"" and will refer to the contour uniformity of comparatively little particles. A well-known method of preparing particles is to spout a mist of liquid and slurry from a nozzle l) 2). Particles for metals, catalysts and food have been prepared by this method. In this case, although an approximate particle diameter can be decided by controlling the nozzle diameter and the violent outflow velocity, it is not easy to completely control ·the contour and to prepare a particle with uniform diameter. ·However, the preparation of perfectly uniform particles is necessary for solders for the adhesion of electronic wiring 3), ion exchange resins4), catalysts and so on. Large quantities of fine particles and super-fine particles are generated when manufactured in the usual way. Large quantities of these fine· particles and super-fine particles have polluted the internal and external' environments of factories. The products yield' ·decreases, also. From such a background, this study examines the preparation of perfectly uniform particles that could be· collected -100% as products. Recently, NASA has succeeded in the preparation of perfectly uniform particles in zero gravity 5). But the preparation of 'perfectly uniform particles by this method is difficult, and it can not be used in general industry"

Jan 1, 2000

By Vladimir Lobanov, Vladimir Skorohodov, Boris Radionov, Olga Makovskaya

"The synthetic sorbents and the activated carbons which are used for the metals extraction from weak process liquors are rather expensive. It is propose to use mineral and synthetic high-porous substances which sharply increased sorption properties by special processing. For achievement the desirable properties sorbents are impregnated by specially prepared solutions. Such solutions should contain the substances or its anionic forms which on the one hand are strong enough fixed in a supporter pores, with another are capable to form the insoluble compounds with extracting metals. Selectivity is provided by chemism of the reagent interactions with extracting metal. Due to the high concentration of a reacting ion in a sorbent phase the capacity and rate of sorption increases. Formed insoluble compound remains in a phase of the sorbent and necessity of its filtration disappears. For synthesis the sulfhydryl compounds which chemical properties allow to increase degree of extraction and capacity of the activated carbon were used. At hydrometallurgical processing of precious metals mineral raw materials the commercial solutions with the concentration of gold from 0,1 to 5 mg/dm3 are received. Commonly gold is precipitated from cyanic solutions by the zinc dust. The sorption methods are widely applicable. But the synthetic sorbents and the activated carbon using to these purposes are rather expensive. Expenses for sorbents even at its regeneration can reach 10-15 % from total expenses of gold extraction from ores. When sorbent regeneration, mostly for carbon, is not provided, this share increases to 30-40 %. Thereupon search of the sorbents combining availability, the sufficient capacity, demanded degree of extraction and the low price is actual. For the specified purpose it is offered to use the mineral and synthetic high-porous materials which sorption properties are sharply rose by special treatment. Among such substances are natural zeolites, silica gel, lignine et al. Similar treatment can improve the sorption properties of sorbents used in practice, particularly, the activated carbons. The simplest treatment of potential sorbents consists in its impregnation by specially prepared solutions. Such solutions should contain substances or its anionic forms - impregnating agents. These agents should be on the one hand strong enough fixed in a carrier pores, on the other hand are capable to form with extracting metals insoluble compounds. The more strong compounds are formed the high degree of metals extraction from solutions. The sorbents with similarly changed properties are named the impregnated sorbents."

Jan 1, 2008

By Tugba Basargan Çagatay Morall, Gülhayat Nasun-Saygili

"The aim of this study is to prepare the apatitic material using colemanite mineral (2CaO.3B2O3.5H2O) which was obtained from Eastern Anatolia, Turkey. For this purpose, colemanite mineral was reacted with different phosphate sources, namely, dipotassiumhydrogen phosphate, ammoniumhydrogen phosphate and ortophosphoric acid at various temperatures and time periods. Experiments were run in batch system. The apatitic material was prepared by a wet method and followed by heat treatment at various temperatures. Structure of the samples was analyzed by XRD, FTIR, XRF and SEM. The particle size analysis was also made for the result product. The experiments showed that reaction temperature, contact time and heating temperature are important parameters to transform the colemanite into apatitic structure. Reaction of colemanite with dipotassiumhydrogen phosphate and ammoniumhydrogen phosphate results in amorphous, non-stoichiometric hydroxyapatite type structure, while acid based phosphate source gives brushite and monetite type product before and after heat treatment, respectively.IntroductionBoron which has properties intermediate between metals and non-metals is a member of semiconductor group of elements. Its atom is very small and has three valence electrons. Boron exists in Earth's crust (from 5 mg/kg in basalts to 100 mg/kg in shale) and in the oceans (4.5 mg/l) [1]. Turkey has 60% of world's boron reserves which is mostly in the form of colemanite (2Ca0.3B203.5H20). Colemanite is the most important calcium containing commercial borate mineral with 5 mol of crystal water [2].Calcium phosphate cements are very useful for bone repair applications because of its chemical structure. They are injectable, easy to shape and can be maintained locally. Because of those reasons calcium phosphate cements are very effective to fill bone defects with an irregular shape [3]. Hydroxyapatite (Ca10(PO)6(OHh) is the major component of the bone (70 wt%). However, hydroxyapatite stoichiometry, composition and crystallinity differ in human skeleton system [4, 5].The main objective of the present work was to study the transformation of colemanite to apatitic material using different phosphate solutions at several time spans and temperatures. The experiments were run in a batch system, change in pH and also weight loss were measured after the experiments. Several analysis methods were used to investigate the chemical and structural changes."

Jan 1, 2012

By Tzu-Chien Lin, Jack Tsai, Ming-Yu Lin, Der-Ray Huang, Jiin-Sen Chen, Jing-Xuan Lin

"In this paper, some DVD-R discs have been selected for long time light exposure test and high temperature and humidity test. Generally, recordable media under long time light exposure maybe be defected seriously. If we use Jitter value 8% as a reference to determine the life time of DVD-R samples, some discs defect after 5 hours of light exposure while some discs can endure over 25 hours. Also if we use reflectivity 45% to determine the life time, some discs defect after 30 hours light exposure while some discs can endure over 40 hours. From our results, the good samples show good characteristics of PI error. The absorption spectrum of recordable media is a good reference to justify the quality of dye media. These results can be used to estimate the life time of recordable discs.IntroductionIn general, the life time of DVD-R with a layer of organic dye recording layer is required for preservation in decades. In addition to optical characteristics and thermal properties, we still need to consider the stability of the dye in recording media. The presentation of the color on organic dye is not only related to the material's property but also related to the light exposure. In this study, we focus on the absorption characteristics and reflectivity of organic dye in optical recording layer after light exposure. The optical properties of discs depend on the functional groups and molecular structure [1]. According to ""DVD Specifications for Recordable Disc (DVD- R)"", the reflectivity should higher than 40%. From measured reflectivity, we can confirm that the important issue is whether dye be affected by light exposure or not. Because each specific functional group absorbs the specific spectrum, we can check the characteristics of functional groups from their UV/Visible Spectra. We also use High-performance liquid chromatography (HPLC) to detect the different components of dye on the recording layer [2]. The jitter value test is to test the error cause by digital signal of recording media. If we use jitter value 8% as a reference to determine the life time of DVD-R samples, the purpose of this study is to investigate the jitter values of recording media after high light exposure and high temperature/humidity test. The results of these test will be helpful for the development of long-life optical storage media."

Jan 1, 2012

By Cheng Gong-jin, Chu Man-sheng, Liu Zheng-gen, Zhang Yong, Liu Jian-xing, Xue Xiang-xin

"High chromium vanadium-titanium magnetite is one kind of Fe-V-Ti-Cr composite ore resources, which owes high utilization value. Owing to lacking systematic study on the sintering of this ore home and abroad, effects of carbon addition and basicity on sintering process and sinter metallurgical properties, such as sinter yield, vertical sintering speed, tumbler strength, sinter machine utilization coefficient, and low temperature reduction degradation were investigated systematically under laboratory conditions in the paper. The results shows that, when high chromium vanadium-titanium magnetite proportion is kept unchanged as 13% in sintering feeds, sintering process index and metallurgical properties are the optimum under carbon addition 5.0% and basicity 2.70, which meets the requirements of blast furnace burdens. This research provides technical parameters for practical sintering production of high chromium vanadium-titanium magnetite.IntroductionHigh chromium vanadium-titanium magnetite (hereinafter abbreviated as hi§h-Cr V-Ti magnetite), in which Fe is closely symbiotic with Ti and isomorphous with V and Cr1'- l, is one kind of typical vanadium-titanium magnetite resources with high comprehensive utilization value but the difficulties are extremely high due to complex chemical composition and mineral structure. At present, the feasible and mainstream utilization process of high-Cr V-Ti magnetite should be the route of agglomeration-blast furnace smelting. Thus, sintering production is the foundation for high-Cr V-Ti magnetite utilization. However, till now there are few research documentations on high-Cr V-Ti magnetite sintering home and abroad. Under the above background, this study focused on detailed researches of high-Cr V-Ti magnetite sintering. Sintering process uses the powders or fine iron ores to produce artificial rich ore with good metallurgical properties 4l Solid fuel provides 90% heat requirement during sintering15J. The appropriate amount of fuel and flux should be added during sintering in order to provide necessary heat and maintain the desired basicity16l. That is to say, carbon addition and basicity are two key factors affecting metallurgical properties of sintering products17J. Therefore, the effects of carbon addition and basicity on sintering process and metallurgical properties, including sinter yield, vertical sintering speed, tumbler strength, sinter machine utilization coefficient, and low temperature reduction degradation, are systemically investigated under laboratory conditions in the study, on purpose to achieve the optimization of sintering process for high-Cr V-Ti magnetite."

Jan 1, 2013

By Raghavan Srinivasan, Y. V. R. K. Prasad, William G. Frazier, Steve C. Medeiros

"Aerospace gas turbine disks operate in an environment of relatively high stresses caused by centrifugal forces and elevated temperatures. These severe conditions necessitate the need for materials with good high temperature strength and low cycle fatigue resistance. One class of alloys used for this task is the nickel base superalloys, out of which, lN 718 is the most widely used in the aerospace industry [I]. The properties of IN 718 are attributed to the combined effects of the chemistry, heat treatment, and microstructure. The chemistry is tailored not only for solid solution strengthening but also for precipitation hardening developed during heat treatment, which combined with a fine grained microstructure lead to excellent mechanical properties such as low cycle fatigue resistance and elevated temperature strength. The properties of a gas turbine disk are sensitive to the microstructure, in particular the grain size, which is dependent on the processing history. The ability to precisely control the microstructural development during forging is dependent on controlling the process so that the workpiece is deformed within a ""safe"" region where no microstructural damage or flow instabilities occur. The microstructural mechanisms during deformation may themselves vary within the ""safe"" region and it is desirable to determine them within the range of parameters that are commonly used in industrial processing. The objective of this work is to establish a relationship between the grain size and the process control parameters i.e., temperature and strain rate, in the hot working of IN 178.BackgroundIN 718 belongs to a class of nickel-iron base superalloys with a face-centered cubic (FCC) austenitic matrix strengthened by precipitation of ordered intermetallic or carbide precipitates and is a nickel-rich alloy strengthened by ordered body centered tetragonal (BCT) precipitates, Y"". The alloying of nickel and iron results in the formation of the austenitic matrix, y, while the addition of chromium and molybdenum cause solid solution strengthening. Also, alloying with niobium causes precipitation of the metastable hardening constituent Y"" (Ni3(Nb,Ti)). Extended aging treatments in the temperature range 650 °C - 980 °C allow the more stable orthorhombic 8 phase (Ni3Nb) to form. Trace amounts of boron are also added to serve as grain boundary strengtheners for high temperature creep resistance. Hot deformation of IN 718 is performed between the Y"" and 8 solvus temperatures to facilitate recrystallization and to control grain growth. While deformation below the Y"" solvus (""""962°C) produces no change in grain size, deformation above the Y"" solvus but below the 8 solvus will lead to a dynamically recrystallized microstructure. The presence of the 8 precipitates will pin the grain boundaries after recrystallization and restrict grain growth so that a fine grain microstructure is obtained. Deformation above the 8 solvus ("""" 1038°C) will lead to a microstructure which has undergone grain growth during deformation."

Jan 1, 2000

By Donna M. Noel

Bacterial strains have been cultivated from solids previously exposed to cyanide that will tolerate 300 ppm sodium cyanide under anaerobic conditions. In selected solid samples, these bacteria have been shown to reduce the level of cyanide from approximately 300 ppm to essentially zero in about 50 days under anaerobic conditions. Various media were investigated, and the nutrients providing maximal growth were ?established .. Degradation of cyanide in sterilized solids was determined for comparison with degradation obtained in bioactive solids. All experiments were conducted at ambient temperature and initial pH of approximately 10.5.

Jan 1, 1991

By Frank Mucciardi, Hujun Zhao, Pietro Navarra

"A heat pipe is a device having a very high effective thermal conductivity in which two-phase flow and heat transfer takes place. Recent research at McGill University has led to a new type of heat pipe that contains a flow modifier. This improvement has enabled the device to operate at the high heat fluxes encountered in the metallurgical industry.This paper summarizes the progress made to describe the fluid flow in the evaporator section of a McGill heat pipe with the goal of understanding how the flow modifier configuration is linked to the film boiling and dry-out limitations. A separated flow model, an instability analysis, a lift-off model and an energy balance model are used to calculate the theoretical CHF with varying flow modifier configurations and operation conditions. A summary of the current work to relate the flow modifier to the dry-out limitation is also given.Determining how the flow modifier affects both the film boiling and dry-out limitation will give insight into improving the flow modifier design so as to extend the operational range of McGill heat pipes in terms of maximum heat flux and heat load capabilities.IntroductionThe McGill heat pipe is a specialized two-phase heat exchanger developed for several metallurgical applications where temperatures and heat fluxes are typically close to or beyond the maximum safe range of conventional cooling technology.Over the last few years, several breakthroughs have brought this device beyond the proof-of concept stage and a series of industrial trials have been performed with success. These trials include two oxygen injection applications for the ferrous and non-ferrous industry [l], and two light metals permanent-mould casting applications [2,3]. Current projects include a blast furnace copper taphole cooling application [4], a copper smelting application and a thermal analysis probe application."

Jan 1, 2004

By Nathanael Hudson, Ruel A. Overfelt, Sushil H. Bhavnani

"In the aerospace and automotive industries, complex shapes exist which require casting. The problem with these cast parts is the empiricism required to develop the casting process and the accompanying time and expense to develop that process.There has been an interest in using fluidized beds to allow molding sand to better encapsulate the complicated surface geometries of lost foam patterns. Fluidization coupled with a mixing jet helps to homogenize the sand through stirring and may improve the integrity of the casting.At issue is the hydrodynamics of the sand and air around the foam pattern. The commercial package PHOENlCSTM is used to simulate the flow around the pre-casting foam geometry. Employing a two fluid approach, each component is considered a fluid that interpenetrates the other phase. To this end, the kinetic theory of granular 'flow for the sand phase was incorporated into the re-compilable PHOENlCSTM code.The results of this study consist of time-averaged void fraction patterns, with voidage being defined as the fraction of air in the mixture, around the foam pattern submerged in a two-dimensional fluidized bed. The model was benchmarked against past fluidized bed experiments. In order to better understand the dependence of the void fraction pattern around the lost foam pattern, certain physical parameters are varied and the resultant void fraction maps are predicted with the model. Physical parameters such as the aspect ratio of length to width, the placement of the mixing jet, and different mixing jet velocities are varied to illustrate the dependence of the time-averaged void fraction on those variables.Results consistently indicate the presence of channeling around the lost foam pattern, with the extent of the channeling and void formation reliant to a greater degree upon the placement of the mixing jet, and to a lesser degree on mixing jet velocity and aspect ratio.The increase in radial position of the mixing jet from the bed centerline had the desirable effect of granting the churning benefits of a penetrating jet, while at the same time minimizing the formation of excess void fraction at the top of the pattern."

Jan 1, 2001

By JiaPeng Xu, Brian Lo, Uday B. Pal, Yihong Jiang, Soumendra N. Basu

"The Solid-Oxide Oxygen-Ion-Conducting Membrane (SOM) electrolysis process has been successfully tested on a laboratory scale, producing silicon directly from silica in a cost-effective and environmentally friendly way. A yttria-stabilized zirconia (YSZ) tube, closed at one end was employed to separate the molten salt containing dissolved silica from a liquid metal anode placed inside the YSZ tube. When the applied electric potential between the liquid tin cathode in the molten salt and the anode exceeds the dissociation potential of silica, oxygen ions are pumped out of the molten salt through the YSZ membrane and oxidized at the anode while the silicon cations in the flux are reduced to silicon at the liquid tin cathode. The presence of high-purity silicon crystals on the surface of liquid tin cathode was confirmed by scanning electron microscopy (SEM) and energy dispersive x-ray spectroscopy (EDS). Silicon crystals were extracted from tin cathode by chemical etching.IntroductionPhotovoltaics (PV) generate electrical power by using solar cells, and dramatically reduce the emissions of greenhouse gases (GHG). Through 2006 to 2011, it grew the fastest of all renewable technologies with operating capacity increasing an average of 58% annually [l]. However, the cost of manufacturing solar-grade silicon (SoG-Si) for high-efficiency solar energy production represents a major barrier to achieving the industrial goal for solar power of $1/Wp (watt at peak exposure) which would enable widespread grid parity. The current contract price of silicon to PV manufacturers is $50-$60/kg, with the spot market in 2007-2008 showing prices as high as $300/kg [2]. This makes the development of low cost and environmentally friendly manufacturing of high purity silicon very important."

Jan 1, 2013

By Stein Tore Johansen

Some ferro-silicon fumaces have heat-recovery equipment. Here, the recovery of electric energy from the off-gases can be increased by increasing the off-gas temperature. This is easily done by reducing the amount of air which usually is mixed into the off-gas to cool the gas mixture. If the off-gas becomes too hot problems with severe fouling or clogging of the gas channels? close to the fumace is observed~ The result is irregular stops to clean the off-gas channels. The paper focuses on the nature? of the clogging phenomena and some of the ways to avoid clogging. A detailed experimental study was carried out at the Elkem Thamshavn Plant. Theoretical studies were performed to understand the particle deposition, turbulent multiphase fluid flow and off gas combustion in the off-gas channels. The study has resulted in reduced clogging.

Jan 1, 1992

By Shantaliu S. Shevade, Muhammad M. Rahman

"This paper presents a systematic analysis of fluid flow and heat transfer processes during the magnetic heating of the substrate material. Heat is generated in the substrate material when a magnetic field is imposed due to change in orientation of the molecules. As a result, the substrate temperature rises. The i;tudy considered microchannels with rectangular and square cross section with heat generation in the substrate due to imposed magnetic field. The results computed were for Gadolinium substrate and water as the working fluid. The purpose of this study is to explore the transient heat transfer coefficient when the fluid is circulated through the substrate via microchannels. Equations governing the conservation of mass, momentum, and energy were solved in the fluid region. In the solid region, heat conduction was solved. From the simulation results, plots of Nusselt number and heat transfer coefficient were obtained over the length of the channel. A thorough investigation for velocity and temperature distributions was performed by varying channel aspect ratio, Reynolds number, and heat generation rate in the channel. It was found that the peripheral average heat transfer coefficient and Nusselt number is larger near the entrance and decreases downstream because of the development of the thermal boundary layer. With the increase in Reynolds number, the outlet temperature decreased and the average heat transfer coefficient increased.IntroductionMagnetocaloric effect (MCE) is the heating or cooling of the magnetic materials due to varying magnetic field. The effect was originally discovered by Warburg. Magnetocaloric materials store heat energy in the way the atoms vibrate and in the way electrons spin within each atom. More heat energy increases the vibrations and also makes the spins more random. When a strong magnetic field is applied to a magnetic material, the magnetic moments of its atoms become aligned making the system more ordered. The more ordered material has lower entropy and compensates for the loss by heating up. When the magnetic field is removed, the magnetic moments return to their random directions, entropy increases and the material cools. Gadolinium is a magnetic material that exhibits high temperature rise during adiabatic magnetization around its transition temperature of 295 K. It has been experimentally observed that adiabatic temperature rise increases with magnetic field strength and can be as high 20 K when a magnetic field of IO T is applied. Thus magnetic field, when applied to a microchannel heat exchanger, causes temperature change in the magnetic material. The fluid flowing through the channel gets cooled or heated due to this adiabatic temperature change."

Jan 1, 2004

By Y. Ide, K. Kishitake

It is expected that an Al-Cr-N composite nitride film may have a higher resistance to oxidation at elevated temperatures than the well-known Ti-Al-N films. The formation conditions of Al-Cr-N films by a de reactive sputtering method and their properties were studied in this study. The films characterized with respect to their high temperature properties such as chemical composition, crystal structure, microhardness, wear and· friction. The crystal structure of the Al-Cr-N films changed from hexagonal phase to cubic phase with an increase in Cr content in the films. The resistivity to thermal oxidation of the Al-Cr-N films is superior to that of usual TI-Al-N films. A half of the friction coefficient in the Al-Cr-N film was obtained comparing with that in the ordinary TI-Al-N film at room temperature and the wear rate of Al-Cr-N film was 2 order smaller than that of TI-Al-N film. The Al-Cr-N films show a small friction coefficient at 500°C and then they are recognized to have good tribological characteristics.

Jan 1, 2000

By Hongfa Hu, Stavros A. Argyropoulos

"This paper describes a mathematical model which simulates numerically reaction driven fluid flow phenomena. The driving force of this reaction is an exothermic heat of mixing. In addition, the model predicts the heat and mass transfer phenomena where both heat source and heat sink co-exist in close proximity. The heat source is generated by an exothermic reaction. The heat sink is formed by a moving boundary such as the melting of a solid. This type of phenomena occur quite often in various metal processing operations in which exothermic additions are immersed in liquid metals. The model is based on the SIMPLER algorithm and uses an enthalpy method to predict the fluid flow, temperature, and concentration fields. The results indicate that the exothermic mixing reaction was responsible for an abrupt rise in temperature around the moving boundary. The intensity of this reaction was also found to be responsible for the enhanced convection of fluid and the acceleration of the moving boundary. The modelling results were also verified by experimental work which included velocity and temperature measurements in a low temperature physical model. IntroductionAlloying additions are used extensively in the treatment of liquid metals during metallurgical processes. The alloying additions introduced into liquid metals can be classified into various classes, each of which follows its own route[l]. As a major group, the exothermic additions follow two different steps during their assimilation into liquid metals. In the first step, upon immersion, a metal shell solidifies around such additions, and then melts back. At this point, the second step commences. During this second step, due to the mixing of the addition with a liquid metal, an exothermic reaction occurs, which liberates large amounts of heat, resulting in an enhanced convection in the liquid metal surrounding the addition."

Jan 1, 1994

By Tatsuo Inoue, Marnoru Mizuno, Toru Matsuoka, Kenichiro Abe

"The distribution of particle reinforcements and the residual stresses in metal matrix composite are simulated by considering the motion of particles and the solidification of matrix associated with temperature variation in the course of centrifugal casting process. In the analysis, a heat conduction equation including heat generation due to latent heat and also mechanical work as well as heat input from successively accumulated element on the air/metal boundary is solved by the finite element technique. After the movement of particles subjected to the centrifugal force and drag are analyzed, the residual stresses are elucidated by using a unified constitutive equation which can describe the behavior both in liquid and solid states. Results of the simulation are compared with the experimental data, and the validity and utility of the procedure is confirmed.IntroductionProcess simulation of metal matrix composite (MMC) is required to determine the mechanical properties of the materials and the efficient process and conditions of the fabrication. Properties of bonding matrix with reinforcements in the course of the processing, for example, affects the strength of the composite, while the final costs of the productions depends on the efficiency of fabrication. Therefore, the simulation of processing of MMC is prerequisite in order to clarify the mechanism to fabricate the material which has been expected to maintain high mechanical properties and the cost performance.Some techniques of processing MMC[l] have been developed so far. Among them, the centrifugal casting technique [2-5] has many attractive characteristics as processing of the MMC: The centrifugal casting technique makes the reinforcements such as particles or short fibers to be distributed in the radial direction by the centrifugal force acting on reinforcements due to the difference in density between reinforcements and matrix. Since the distribution of reinforcements affect the mechanical properties of MMC, the composite with functionally gradient mechanical properties can be provided by the centrifugal casting technique."

Jan 1, 1994

By E. B. Freidina

We have investigated a new electrochemical process for preparing lead-calcium alloys. Calcium metal, reduced fiom a molten chloride mixture, forms an alloy with liquid lead cathode. The addition of calcium carbonate to conventional CaC12-NaCl electrolyte enables us to avoid chlorine production on the anode and replace it with oxygen and carbon dioxide. The ternary system CaClz-NaC1-CaCO3 has a range of melt compositions, where the electrolysis can be held below 650°C. In order to prevent the side reaction of carbon deposition on the cathode we have separated the anolyte from the catholyte with alumina diaphragm. The factors, which affect the level of impurities and the current efficiency of the process, are discussed.

Jan 1, 1999

By Akio Ohta

The Hyuga smelter has been producing ferronickel by a rotary kiln-electric furnace process in Miyazaki, Japan. Several approaches to improve our operation have decreased the electrical energy consumption. A new process was developed to decrease the cost of energy even further. Oil and technical oxygen are injected through lances to heat up the calcined ores (calcine) instead of the electric power. Main problems during the development of the process were the short life of the water-cooled lances, the check on security of the safety system and the eruption of combustion gases through the calcine bed. These problems have now been overcome successfully, and stable operation can be maintained. The addition of 1 Litre of heavy oil per tonne of ore can save the electrical energy requirement by 8.6 kwh per tonne of ore. The new process has resulted in a reduction of the electrical energy consumption by more than 10 percent

Jan 1, 1992

By J. Dille

Metallic cobalt exist in two allotropic forms : the hexagonal compact a which is stable at low temperature ( ( 420') and the cubic form 0 stable at higher temperature. This latest form is the only one which is ductile. During the electrode position of Co, in moderate acidic conditions, we noticed a code position of both a and B forms. The influence of several parameters on the B/a ratio in the deposit was investigated. High acidity and the presence of Fe increased its ratio; on the opposite, high temperature promote the a phase. No significant influence on the material were noticed. The differentiation of a and B forms of Co is rather difficult and the method of J. Scoyer was improved quite successfully.

Jan 1, 1988

By R. K. Mehta

Microorganisms have been increasingly used in applications such as-metal solubillzation, precipitation and recently being used as flocculants. Optimal control and on-line monitoring of these processes occurring in microbial reactors are of extensive interest but often difficult because of the unavailability of a mechanistic model of the process and on-line direct sensors. In this paper a dynamic populatlon balance model of microbial desulfurization will be presented. The influence of certain physical and biological parameters on the leaching rate will be illustrated via computer simulations and an extended continuous-discrete Kalman filter will be Implemented for estimation of unknown states.

Jan 1, 1991