Search Documents

By Eiichi Kuzuno, Atsushi Shibayama, Toyohisa Fujita, Kazuo Koike, Toshio Miyazaki, Hitoshi Masuda

"A solid sulfur is more useful to recover and store than a sulfuric acid as a by-product in the zinc hydrometallurgy. In this experiment a zin concentrate (sphalerite) was leached with ferric sulfate at about 373 K for 3 to 6 hours. Zinc was leached more than 95%. After a solid-liquid separation, the leached residue contained solid sulfur was obtained. The particles in the residue were dispersed by lignin and the solid sulfur of approximately 85% was recovered as float product by a flotation with frother in the pH 4. The dried float product was heated at 413K for 2 hours. The pure solid sulfur was recovered. On the other hand in the leached liquid a zinc oxide was ·added and ferrous .iron was oxidized to ferric iron by blowing oxygen. This ferric iron was returned to the zinc leached process after solid-liquid separation.IntroductionZinc concentrate is usually roasted as pretreatment in zinc hydrometallurgy and the produced S02 is changed to sulfuric acid. However, recently in Japan the utilization of sulfuric acid has been limited and it is more costly to store. Instead of producing sulfutic acid the solid sulfur recovery has been examined by direct leaching of zinc_ concentrate in this experiment.In the direct leaching, several kinds of effects have been studied for leaching of sphalerite in ferric sulfate solution. The addition of lignine siilfonate1 • 2) and fine· grinding3) increases the · speed arid leaching fraction of sphalerite. The leaching ratio depends on impurities in sphalerite ores4 • 5). Here, the zinc concentrate is leached ferric sulfate solution under atmospheric pressure at 373K. The solid sulfur in leached residue is separated as float products from other solids by sink-float separation and flotation. The sulfur in float products is purified by evaporation at 413K and recovered."

Jan 1, 2000

By Elsa Agante

Recycling of solid wastes, a common practice nowadays, requires the separation of the different materials in order to increase the products added value. The separation of one plastic from mixtures of different types of plastics is not easy due to their similar physical properties, but different techniques are available, from automatic sorting systems based on optical sensors to techniques adapted from mineral processing, namely gravity, froth flotation and electrostatic processes. In the last decade, many researchers have addressed the separation?s problem of different polymers, like Polyethylene Terephthalate (PET) and Polyvinyl Chloride (PVC), two polymers commonly used in packaging which have similar density. One proposed technique is the classical froth flotation performed in agitated cells. Froth flotation is a versatile and relatively cheap process widely used in mineral separation. It is based on the different behaviour of particles in the presence of an inter-phase air-water, which depends on the materials surfaces properties. Froth flotation can be affected by some variables such as impeller speed and air flow rate. Agitated cells, when used with low density materials, like plastics, can produce overstated turbulence that prevents the adhesion and collection of particles in the froths. In this case, separation is favoured by column flotation smoother hydrodynamics. This paper proposes the separation of PET from PVC by column flotation. The experimental work was carried out in a column of 9cm diameter and 1m high. The effects of some operating conditions, such as depressor and frother concentration, air flow rate and feed grain size on products grade and recovery were evaluated and the best flotation conditions for the separation of these plastics were established.

Jan 1, 2006

By Shaohua Ju, Jin-hui Peng, Ya-jian Wang, Shuai-dan Lu, Li-bo Zhang, Lei Guo

"The granulation of a red mud is of great importance for recycling this material as an adsorbent for waste water or gas. A new granulating process was developed and its effect was evaluated. To reduce the cost of the granulation process, the wet filter cake (containing 25% water) was directly mixed with different cement contents (4%, 6%, 8% and 10% based on wet material). The mixtures were placed in a moist environment for 4 days, and then were washed with deionized water until the pH values of leachants were lower than 9.0. The efflorescence ratio, surface area and particle size of the aged mixture were determined, respectively, by bottle shaking experiments, N2 adsorption and screening. The results showed that the best addition of cement is 2%, and this yielded granulated material with a particle size of less than 2 mm, an efflorescence ratio of 4.83% and a specific surface area of 17.42 m2/g.IntroductionRed mud is a residue of the aluminium industry that is produced during the alkaline extraction of alumina from bauxite by the Bayer process. For every ton of alumina that is produced, the amount of red mud generated can vary from 0.3 to 2.5 tons, depending on the characteristics of the bauxite. In its typical form, red mud is brick red in colour, caustic, about three times as dense as water and, when un-neutralised, has a high pH, typically around pH 13 [1]. It is primarily composed of iron oxide, silica and alumina, along with traces of heavy metals. Red mud particles are quite small; typically 99% will pass through a 0.6 mm sieve and 87% through a 0.038 mm sieve [2],"

Jan 1, 2012

By Carlos Schvezov, Eliana Agaliotis, Alicia E. Ares, Mario Rosenberger

"The interaction between a solidification front and a spherical particle was modeled and simulated in order to study the phenomenon of ""pushing"". Finite element methods were employed in axisymetric domains. The drag force is calculated from the calculated fluid flow field and the repulsion force is the Lifshitz-Van der Waal force. The thermal field is decoupled from the force field. The model is applied to a metallic matrix containing particles with similar, lower or higher thermal conductivities than the matrix, resulting in planar, convex and concave interface shapes, respectively.The results show that the critical velocities for pushing for concave and convex interfaces are about one order of magnitude larger and one order of magnitude lower than the critical velocity for flat interfaces, respectively. The simulated results were in very good agreement with reported experimental results.IntroductionThe solidification interface of materials containing spherical particles in some cases can push the particle ahead the interface. This phenomenon generally occurs during the solidification of different materials such as, metallic alloys containing native particles, metal matrix composites containing particles or fibers as reinforcements and crystallization of semiconductor, optical, optoelectronic or biological materials. In all cases the interaction strongly determines the distribution of particles and the resulting physical and physic-chemical properties of the resulting material. The phenomenon has been investigated for many years both experimentally and by mathematical modeling [1-21]. The process is complex due to the variety of phenomena involved during pushing. In all cases, the physical problem depends on the properties, nature, and morphology of the interacting media; the particle, melt and solid; and external fields such as gravity, thermal and electromagnetic fields."

Jan 1, 2012

By Kaixi Jiang, Bangsheng Zhang, Lei Zhang, Haibei Wang, Xiaoping Zou

"China plays an important role in the global molybdenum industry; in fact, both China's molybdenum mine and smelter production ranked first in the world. The characteristics of China's molybdenum resources are quite complex, and moly-nickel ores with carbon, coppermoly ores and wulfenite can be only found in China. This paper firstly introduces China's molybdenum resource/ reserve situation. Secondly, the status of molybdenum smelting technologies, especially roasting by rotary kilns and multiple-hearth furnaces, are discussed. The practices and the development of some new technologies, such as pressure leaching, solvent extraction, ion exchange, carbon adsorption for moly-nickel ores and low grade molybdenite concentrates, are also introduced.IntroductionMolybdenum is widely used in special steels, aviation, alloys, chemistry, electronic and medical industries because of its excellent physical and chemical characters [1,2].In nature, molybdenum exists mainly as molybdenite associated with copper ore which are the main material for smelting. About 99% of molybdenum is produced from molybdenite. In addition, wulfenite, molybdenum oxide ore and graphite shale containing Mo-Ni have also industrial value to extract molybdenum and other metals such as Ni, Re, Pb and Zn. The reserves of molybdenum in China are about 8.4 million tons metal; China is ranked as the second largest source in the world. The output in China is more than 40 kt in 2010. Ferromolybdenum is the main product and then ammonium molybdate. The consumption in China is about 20 kt and the rest is exported to overseas.The first molybdenum smelter in China was built in 1963. Today the main producers include Jinduicheng Moly Company, Luanchuan Moly Company and Jiangxi Copper Group Company. Technologies and equipment have changed greatly. Roasting and multi-hearth furnaces are widely used. Several new processes were developed such as pressure leaching, solvent extraction, ion exchange and carbon absorption [3-8]."

Jan 1, 2012

By Zhong Juya, Wang Yong, Guo Xueyi, Song Yu, Tian qinghua

"In this work, the flow of zinc in China, 2004, was traced within the STAF model, and the situation of production, consumption and recycling of zinc resources in China were introduced. The SFA is performed on zinc flows during its one year life cycle in detail. The result reveals that China produces and utilizes a large amount of zinc, while the efficiency of renewable zinc resources is still relatively lower. As one of the biggest producer and consumer of zinc in the world, China is facing a severe depletion of zinc resources. How to increase the resource efficiency is a significant issue for zinc industry of China. Based on the result, several advices were proposed in the paper, aiming to contribute important reference information for the industrial metabolism and resource management and recycling of zinc industry in China. IntroductionZinc is one of the important metals in national economic development in China; it has good conductivity and corrosion resistance, with high scalability when heated to 100 ~105_. Zinc is mainly used for galvanized zinc industry, as the coating of steel and various parts, and it has also been applied to the manufacture of brass, bronze and corrosion-resistant alloys, which are widely used in machinery manufacturing, printing, national defense and so on. In addition, zinc compounds are utilized in various fields, for example, ZnO is used for infiltration wood, paper, rubber, paints, etc.; ZnSO4 for leather, ceramics, textiles, medicine, etc.; ZnCl2 for infiltration wood; ZnS2O4 and Zn (HSO2 • CH2O) 2 for the paper and textile bleaching, etc. [1]. The extensive use and consumption of zinc in industrial production and social life promot the rapid development of zinc industry, which made zinc the third largest non-ferrous metals in the world."

Jan 1, 2008

By R. W. Smith

The flotation response and electrokinetic behavior of Chlorella vulgaris and Chlamydomonas sp . when using dodecylamine hydrochloride as collector were studied in the absence and presence of Pb(I1). Also, an electron microscopy study was made of the algae after Pb accumulation. The flotation behavior of the organisms after Pb accumulation appears at least partially related to the location of the abstracted Pb onto or into the organisms.

Jan 1, 1991

By Katsukiyo Marukawa, Manabu Iguchi, Sigeta Hara, Shinichiro Yokoya, Sigeo Takagi

"A numerical analysis and water model study of the mold region of a continuous casting apparatus was performed with a novel injection concept using swirling flow in the pouring tube, to control the heat and mass transfer in the continuous casting mold.As a result, the following results were found:1) By changing swirl strength, it is easy to control the flow pattern as well as the direction of the flow.2) Uniform velocity distribution can be obtained within a very short distance from the outlet of the nozzle.3) Heat and mass transfer near the meniscus can be remarkably activated compared with a conventional straight type immersion nozzle without swirl.4) Swirl helps the superheat in the melt dissipate.S) Penetration depth of nozzle outlet flow is decreased remarkably by the application of swirling.6) For the case without swirl, the peak of the flow moves near the mold-wall with flowing down from the outlet of the nozzle due to the Coanda-effect. On the other hand, peak of the flow moves near the mold axis with flowing down from the nozzle-outlet within considerable short distance, namely axi-symmetric velocity distribution can be obtained within very short distance from the nozzle-outlet.Those findings mentioned above are very useful to control the flow pattern in the billet and bloom continuous casters."

Jan 1, 2001

By Jie Ma, Shun-Li Zhao, Jian Zhao, Jie-Yu Zhang

"Microstructural morphology evolution of Ni-45wt.%Mo droplets during rapid solidification process was investigated using an advanced modified 3D cellular automaton-finite element(CAFE) model by CALCOSOFT software. The model was modified by User-defined functions (UDFs) and validated with experimental solidification microstructural morphology of Ni-45wt.%Mo droplets available in the literature. Then, the influences of convection heat transfer coefficient, superheat of the alloy droplets and droplets size were investigated during the rapid solidification process. The predictions show that microstructural morphology is obviously sensitive to convection heat transfer coefficient and droplet size. With the decrease of convection heat transfer coefficient, the grain density decreases. In addition, the decrease of the droplet size could obtain refined microstructure. However, decrease the superheat ofNi-45wt.%Mo droplets has little effect on microstructural morphology.IntroductionFor several decades, much attention has been paid to undercooled alloy droplets of rapid solidification process for which can obtain refined microstructure, decreased microsegregation and extended solubility of alloying elements [1-3]. Extensive prior work shows that solidification of droplets plays an essential role in advanced material properties [ 4]. Consequently, it is very important to investigate the microstructural morphology evolution, especially for dendrite growth during non-equilibrium solidification process, for dendrite growth reflected the kinetics of the crystal growth process."

Jan 1, 2013

By M. Urda-Kiel

Stainless steel is increasingly used as a cathode starting sheet. It was shown earlier that even when depositing copper on copper, a substrate-influenced zone appears in the deposit structure, followed by a transition zone and finally by the electrolysis-influenced structure. On copper, the substrate-influenced zone has a thickness of twenty micrometers and on titanium, eventually more than fifty micrometers. Initial nucleation and growth have a considerable influence. In this paper, copper was deposited in a channel cell on four different 304 stainless steel substrates: mechanically polished and anodized, respectively, at 0, +400 and +800 mV/SHE in 1M H2SO4 at 20°C. Copper was deposited under electrowinning conditions after solvent extraction (SX) (40 g/l Cu++, 180 gh/l, H2SO4, 20 or 60°C). The results showed that, although Auger surface analyses of the substrates were only slightly different one from another including the oxide thickness, nucleation and initial stages of growth were very sensitive to the surface treatment of the substrate. Potential step and current step methods gave similar results : progressive nucleation followed by 3D diffusion controlled growth. The highest nucleation frequency was observed on stainless steel anodized at 0 mV/SHE, under various electrolysis conditions. The potential influence of these findings on industrial practice is discussed.

Jan 1, 1999

By Kenji Morinaga, Hiromichi Takebe

"Ge-S binary glasses in the range 57 to 90 at %S at 0.5 to 3 at %S intervals were prepared by a conventional melting technique using fused quartz ampoules as melting containers. Impurities contaminated during preparation process are evaluated by IR spectroscopy. The causes of impurity contaminations are discussed. Density data in a systematic series of Ge-S glasses is demonstrated. IntroductionSulfide glasses are of particular interest for new laser and nonlinear optical materials in the near-infrared and infrared regions [1]. Sulfide glasses have the features of low-phonon-energy and high refractive index with moderate rare-earth ion solubility. The low-phonon-energy is favorable for the reduction of nonradiative rate for the emission of rare-earth ions. The high refractive index results in a high radiative-rate and in a high third-order nonlinearity. However, impurities may degrade the superior optical properties of sulfide glasses.In this work Ge-S glasses were prepared by a conventional melting technique. Impurities contaminated during the preparation process are evaluated and their causes are discussed for future improvements. The measured densities of Ge-S glass samples were compared with the results of previous studies [2], [3]. Ge-S glasses have some favorable properties for practical .applications including non-toxicity, good thermal and chemical stabilities."

Jan 1, 2000

By Terry C. Cheng

The Akita Hematite Process is currently the only hydrometallurgical iron removal process producing saleable iron by-products in the zinc industry. In this study, McGill University and Akita Zinc Co. have worked together into elucidating the basic precipitation chemistry of the process from the standpoints of hematite product quality and prevailing precipitation kinetics. This work determined that hematite is produced under the applied conditions (T = 195?200oC,PO2 = 103?414 kPa) directly without prior formation of basic ferric sulphate and transformation of the latter to hematite as thought originally. The rate-limiting step responsible for the long retention time (~180 min) was found to be either the re-dissolution of ferrous sulphate according to the batch reactor studies, or the slow hydrolysis of the remaining ferric sulphate according to the continuous reactor studies. Another interesting contrast between the batch and continuous reactor data was the degree of sulphur contamination (1.5 vs. 3.8%, respectively) and the specific surface area of the product (10 vs. 30 m2/g, respectively). These differences in addition to the co-precipitation of SO4-containing phases such as jarosites, alunite, and anhydrite were attributed to the significantly higher supersaturation level prevailing in the industrial continuous autoclaves that yields highly aggregated sub-micron hematite crystallites contaminated with chemisorbed sulphate ions.

Jan 1, 2003

By Baokuan Li, Fang Wang, Meilong Shan

"As the advantage of uniform bus loading, the electroslag remelting (ESR) furnaces with three - phase installation by delta or star connection are mainly used to produce the large or super large ingot. The electrical efficiency is significantly improved as the short circuiting through the molten slag. However, little is found about fiindamental research on the electromagnetic field of the ESR system with three -phase installation. A three-dimensional (3D) finite element model was developed to simulate the current density, magnetic field, electromagnetic force and Joule heating for a system of electrode, slag and ingot in the ESR system with three -phase installation.IntroductionThe metallurgical performance of the ingot is the fundament and precondition to obtain the large forging of high quality, which has a critical role in the producing of forging. The electroslag process (ESR) to product the metal materials of high homogenization and clarity become more and more popular[1].The electroslag process is a special smelting technology of producing small ingots, which originate in 1950[2].At present the three, four or six electrode is used in large scale electroslag furnace. It has been found that the deeper molten pool and the wider of the two-phase zone with only one large diameter of electrode to product large ingot effect the solidification microstructure of ingot[3]. However, the molten pool becomes shallow relatively with several electrodes producing the large ingot, which is benefit to the solidification microstructure of ingot. Three electrodes electroslag remelting furnace take the three phase equilibrium power supply to making the load and electric power network balance, avoiding the distortion phenomenon induced by single phase power supply and saving electric power. It also can uniformize the distribution of heat source."

Jan 1, 2012

By Krishna Kumar

"Growth of electronics waste (e-waste) and lack of appropriate disposal mechanism are the great concern for developing countries like India. The domestic generation of e-waste in India is rapidly growing with the development. The imported substance is also substantially contributing to the e-waste inventory. Recycling of e-waste is mainly carried out in unorganized units in India. The primitive recycling technique used by the unorganized sector is a great threat to the environment and the health of the operators involved in these profession. Therefore, improvement of technology used by these units towards a cost effective, environmental friendly alternative could be the solution to the present crisis. Few initiatives of recycling have, however, come up in recent years in organized units. The precious metals are still recycled in the developed countries. This report discusses the inventory, technology status, legal legislative and existing practices of e-waste management in India.1. INTRODUCTIONInnovation, research and development in the field of electronics and information and communication technology (ICT) lead to convenient, independent human life. Consumption of electronics and hardware products has enhanced by manifold. Electronics and hardware sectors have, thus, become the fastest growing sector in the world. Faster obsolescence of these products is forcing users to replace products with an advanced technology. Life cycles of these products are few years. Discarded electronics products are, therefore, accumulating alarmingly in our society. Electronics waste (e-waste) is a crisis not only due to its volume but also for presence of its toxic ingredients, like heavy metals (e.g. lead, mercury, cadmium, hexavalent chromium) and flame retardants such as poly brominated biphenyles and poly brominated diphenyles ether. These substances create potential occupational and environmental health hazardous."

Jan 1, 2011

By Bruno Lebon, Koulis Pericleous, Georgi Djambazov, Mayur Patel

"High speed compressible jets are used in a number of steel-making applications. In the case of the BOF, a compressible oxygen jet reacts with a carbon-rich iron bath to reduce carbon levels and produce steel. The intensity of the process is governed by the speed of the jet and by the size and shape of the depression created in the metal and slag by the force of the jet, i.e. by the corresponding free surface. This is a difficult CFD problem, since there are compressible and incompressible regions in the flow domain, which need to be handled differently in a finite-volume (FV) pressure-correction scheme. Also, standard turbulence models do not account for compressibility, or the large difference in density between the cold oxygen jet and the hot reacting surroundings. Corrections are introduced to the k-E model to remedy this deficiency and the results are validated against experimental data. The compressible/incompressible boundary is handled through a transition region, based on Mach number.IntroductionThe deformation of a free surface by a compressible high speed jet is of paramount engineering interest, particularly for understanding the physical processes within a Basic Oxygen Furnace (BOF). In a BOF, a supersonic oxygen jet impinges on a molten iron surface, thereby creating a cavity. Oxygen penetrates the bath and removes carbon, resulting in low carbon steel [1].The challenges in modelling such a process lie in coupling a solution domain with distinct compressible and incompressible regions and in dealing with large density differences between the modelled gas and liquid. The modelling of compressibility within the jet is crucial, since the correct velocity profile in the jet is required to determine the cavity depth with accuracy."

Jan 1, 2012

By Amanda C. Lima, Luiz Augusto H. Terrones, Sergio N. Monteiro

"Fabric from weaved yarns made of jute fibers have been considered as reinforcement for polymeric composites. In particular, these fabrics obtained from discarded sackcloth are presently being investigated as environmentally friendly composites with recycled polyethylene matrix. The objective of the present work was to compare the practical properties and economical aspects of these composites with those of conventional materials such as wooden board and gypsum panels for building application. The comparison showed that, depending on the amount of post-used jute fabric, a cost/benefit analysis favors these composites over the conventional materials.IntroductionThe increasing amount of wastes generated by human activities is becoming a worldwide problem of pollution with growing consequences to the environment. The question on how to dispose these wastes is, therefore, a major global issue. Among the possibilities of it gating the problem, the use of materials with characteristics of being renewable, biodegradable and recyclable is considered an environmentally correct solution. Examples of this type of materials are left over lignocellulosic fiber from coconut husks and sugarcane bagasse [1] that, after the primary extraction of edible pulp and juices, can be recover for industrial application. Nowadays, the main use of these fibers is to reinforce polymeric composites applied as components for building construction and automobile parts [2,3]. In addition to these applications, composites reinforced with residual lignocellulosic fibers may replace conventional furniture and panels made of wood and thus help to reduce deforestation [4].Environmental protection is not the only motivation for recycling natural fiber wastes. In developing regions activities associate with collecting and processing residual fibers provide job opportunities for low-income people. Moreover, if the lignocellulosic fiber is collected as a recyclable waste, it hes the economic advantage of a comparatively cost, which constitutes in a relevant difference as a choice for commercial utilization."

Jan 1, 2008

By José Sancho, Julia Ayala, Purificación García, Begoña Fernández

"A study is carried out to see the adequacy of using flying ashes coming out from a Power Station to eliminate the copper present in waste cyanide waters that are generated in gold mines.Tests were carried out to see how effective the use of ashes taken from two Power Stations could become. Later, the tests are made using ashes coming from Narcea Power Station as this station is near the mine under study.The work is centred on looking for an economically adequate solution to close the waste decanting ponds of the mine. After several tests, a solution is reached through filtration in static layers.IntroductionThe use of coal to adsorb some water-soluble substances has been widely studied [1,2,3,4,] both in the treatment of drinking waters and in determined stages of selective detachment of cyanide gold complexes in cyanide lixiviation processes [5]. Flying ashes sent to the atmosphere by Power Stations as a sub-product of the combustion of this combustible are generally made of more of a 70 % of a vitreous aluminosilicated material and of an active residual material which may be changeable making them potentially useable as adsorbents. Nevertheless, the properties of each kind of ashes depend on the characteristics of the Power Station, of the combustibles being used, of the combustion system, etc.The aim of this work is to demonstrate the adequacy of flying ashes to eliminate the copper present in cyanide waters coming from gold mines either by adsorption or precipitation of the metal. For this study, tests are carried out with Asturian ashes which have a low quantity of lime. The results obtained in the tests demonstrate the effectivity of the method used. To be absolutely concrete, the work is carried out to establish the use of these ashes in the closing of Asturian installations of cyanide lixiviation"

Jan 1, 2008

By Paulo von Krüger

This paper deals with the cell design and operation of a tin electrorefining 1:5 pilot plant. The purpose of the work was the fitting of the basic parameters to be used in a full-scale tankhouse from a major Brazilian tin producer. The main specific difference was the use of permanent stainless steel cathodes instead of conventional tin starting sheets. The results of both product quality and operating parameters are discussed.

Jan 1, 2003

By Ibrahim Yusufoglu, Cem Kahruman, Sedat Ilhan, Ahmet Orkun Kalpakhi

"Scheelite is the main raw material in tungsten production. In hydrometallurgical processes, extraction of tungstate ions into solution is very important. During the leaching of scheelite in oxalic acid solutions, tungsten dissolves as a chelate complex. Scheelite includes impurities along with calcium tungstate. Determination of the dissolution of these impurities is important in the subsequent tungsten production stages. In this study, scheelite was dissolved in oxalic acid solutions and the dissolution of impurities was investigated. The quantities of dissolved impurities were determined by ICP - OES and characterization of the undissolved impurities in the leach residues was carried out by SEM - EDS analysisIntroductionScheelite and wolframite ores are used for the industrial production of tungsten. Both ores are dissolved in acidic or basic solutions, and ammonium paratungstate is obtained as an intermediate product. Prior to crystallisation of ammonium paratungstate, all the impurities must be removed. Among these, Fe, Si, P, Mn, Mg and Mo are classified as ""harmful"" elements and different methods are used for their removal [1]. During purification, solvent extraction, ion exchange, etc. methods are used.Potashnikov et al. [2] studied the dissolution of scheelite in acidic solutions and the effects of stirring speed, temperature and oxalic acid concentration on the dissolution kinetics.There are no works in the literature about the removal of impurities from scheelite ores in oxalic acid solutions. Therefore, the aim of this work was to investigate the dissolution mechanisms of impurities during the leaching of scheelite in oxalic acid solutions. The effects of temperature and oxalic acid concentration on the dissolution were also investigated. In addition, the characterization of the impurities which were not dissolved was studied."

Jan 1, 2012

By V. Bojarevics, K. Pericleous

"A number of different methods have been developed for noncontact electromagnetic treatment of liquid metal and to investigate the melting/solidification processes. Applying AC magnetic field in terrestrial conditions, along with the buoyancy and thermo-capillary forces, results in turbulent flow. The use of a homogenous DC magnetic field allows damping both of the turbulence and the large scale flow at different rates leading to surprising results at some stages. The dynamic interaction of the turbulent flow with the oscillating interface needs to be accounted if it is required to levitate liquid metal of up to few kilograms without the contact to container walls. At the high values of magnetic field some oscillation modes are damped quickly, while others are modified with a considerable shift of the oscillating droplet frequencies and the damping constants from the non-magnetic case. Numerical models are used to investigate behavior of liquid metal suspended in high DC magnetic fields providing microgravity-like conditions with laminar viscosity and heat transfer to the surroundings.IntroductionSince the early Electro Magnetic (EM) levitation experiments [1] in AC magnetic field it became apparent that the levitated liquid metal is prone to oscillation and instability. The EM and electrostatic levitation experiments with liquid metal droplets show difficulties related to confinement stability and a need for complex correction functions to establish a correlation between the measurements and the droplet material properties [2,3]. Intense internal fluid flow is visually observed, apparently being in the turbulent regime for earthbound conditions."

Jan 1, 2012