Search Documents

By Shuangsuo Yang

Based on field observations and physical modeling of simulated materials, the dynamic equilibrium principle on the whole interaction process between the surrounding rocks and support of large deformation roadways in coal mines has been developed. It explains the methods of forming the bolted strata and its changing load capacity with deformation. It also points out the factors and conditions for forming the bolted strata as follows: (1) many entries in coal mines are subject to large deformation. During their service life, it goes through the following process, elastic > plastic > fiacture > broken > loosening, etc. During this dynamic process, the mechanisms of supporting structure are changing and therefore the interaction between support and rocks experiences a process of dynamic equilibrium. Furthermore, the required supporting force for stabilizing the surrounding rocks shows overall decreasing trend; (2) the bolted strata is a special supporting structure consisting of bolt, rock skin protection devices and rock strata within the bolted horizon. As deformation increases, the supporting structure of the broken strata within the bolted horizon experiences a process of periodic change, from equilibrium > not equilibrium > equilibrium. Corresponding to this change, the supporting capacity of the bolted strata also fluctuates and gradually decreases; (3) under the bolted strata, the stability of a large deformation roadway is dynamic and step-wise; and (4) the formation of bolted strata, especially bolted broken strata depends on the existence of compressive force. Supporting the bolted strata is not constrained by the quality of the surrounding rocks. It has broad range of application.

Jan 1, 2005

By Murali Gadde

Design of underground excavations in coal mines involves two major tasks: estimation of stresses and determination of rock mass strength. Owing to the complicated nature of rock mass, progress in its strength determination has lagged significantly compared to advancements in stress analysis techniques. Also, because of the impracticality of conducting field-scale strength tests, experimental approaches have very limited applicability in estimating rock mass strength. As a result, many empirical rock failure criteria have been developed based on observed performance of in situ rock structures. Unfortunately, all the popular rock mass strength criteria are based on data from large-scale ?isotropic? non-coal structures and thus can not be directly applied to coal mines. In this paper, an attempt has been made to adopt the popular Hoek-Brown (H-B) criterion for use with coal measure rocks. First, the H-B criterion is examined against laboratory triaxial strength data for different types of coal measure rocks. Then, procedures to estimate the H-B rock mass strength parameters relevant to coal measure rocks are suggested. Finally, a case-study has been given to show the usefulness of the proposed strength estimation approach.

Jan 1, 2007

By Gabriel Esterhuizen

Observations of pillar conditions in limestone mines showed that the presence of weak bands in the limestone can result in pillar damage at stresses that are lower than one would otherwise expect. The objective of this National Institute for Occupational Safety and Health study was to investigate the mechanism of failure caused by the presence of weak bands by using a series of numerical models based on realistic physical properties. The effect of the weak bands on pillar strength was also investigated by developing a series of pillar models with different width-to-height ratios and determining their strength by simulating a servo-controlled loading condition. The material properties of the bands and the limestone were varied and their effects on pillar strength were determined. Model results demonstrated failure development similar to the pillars observed in the field. The weak bands were seen to develop tensile stresses in the limestone as they extrude under increasing stress. The limestone fails in tension at a much lower stress than its expected uniaxial compressive strength. The results showed the load bearing capacity of the pillars can be reduced significantly by the presence of multiple thin weak bands. The degree of strength reduction is largely dependent on the compressive strength, the frictional resistance and the thickness of the weak bands. Single weak bands do not affect pillars as severely as multiple bands. However, the model results show that a single thick weak band, which comprises more than about 2 percent of the pillar height, can cause a significant reduction in pillar strength. The weakening effect of the bands become less severe as the pillar width-to-height ratio is increased. Field observation of spalling and failure associated with weak bands in limestone pillars show that the failure mechanism in the models resembles the observed failure. The model results provide insight into the important factors affecting pillar strength in the presence of weak banded materials.

Jan 1, 2007

By Sanjay Kumar Singh

The mechanics of load transfer in bord-and-pillar mining is not well understood despite the evolution of the art of pillar extraction over the last 20 years via trial and error (empirical) or Rock Mass Rating (RMR), simple monitoring and pillar extraction experiences at neighboring mines. Variations in geologic conditions and pillar extraction methods, along with a lack of comprehensive instrumentation programs for monitoring ground behavior during pillar recovery, are among the factors that make it difficult to predict how strata will respond to pillar extraction. Efficient and safe use of roof supports depends on the interaction between the designed support and coal strata. Of particular interest in this study is the mechanics of strata deformation as influenced by geologic conditions, pillar extraction methods and optimum support with load-bearing capabilities in strata control during mass exploitation of underground coal deposits required detailed investigation,?. To provide a better understanding of the mechanics of strata deformation, as researchers, we have collected data and reviewed measurements of convergence and stress in one mine of South Eastern Coalfields Limited (S.E.C.L.), i. e., in North Chirimiri Pondary Hills (NCPH) and have completed numerical modeling with FLAC software for (Fast Lagrangian Analysis of Continua modeling, Itasca India Consulting Pvt. Ltd.) for two typical pillar extraction plans. Stress distribution in the mine roof above pairs of roof supports was calculated to demonstrate how Resin roof bolt support installed support contributed to roof block movement control. It was shown that overall stress and roof-floor convergence patterns were most influenced by the stiffness of coal measure rocks and by pillar extraction sequences and layouts. Also, resin roof bolts and other support systems play a critical role in controlling stability of both the immediate roof and the main roof for a distance of up to 18 meters (i.e., working coal seam height X three times) above the seam. Installed supports provide unique strata control advantages over other types of secondary support by significantly reducing the time between mining and installation of the secondary support. Although resin roof bolts are similar to posts in stiffness and capacity, they are more effective than posts under static loads because they can yield and still maintain loads at nearpeak capacity(Singh, et al., 2006), whereas posts fail and lose their ability to limit mine roof deformation.

Jan 1, 2012

By D. F. Scott

Seismic tomography, as used in mining, is based on the principle that highly stressed rock will demonstrate relatively higher P-wave velocities than rock under less stress. A decrease or increase in stress over time can be verified by comparing successive tomograms. Personnel at the Spokane Research Center have been investigating the use of seismic tomography to identify stress in remnant ore pillars in deep (greater than 1220 m) underground mines. In this process, three-dimensional seismic surveys are conducted in a pillar between mine levels. A sledgehammer is used to generate P-waves, which are recorded by geophones connected to a stacking signal seismograph capable of collecting and storing the P-wave data. Travel times are input into a spreadsheet, and apparent velocities are then generated and merged into imaging software. Mine workings are superimposed over apparent P-wave velocity contours to generate a final tomographic image. Results of a seismic tomographic survey at the Sunshine Mine, Kellogg, ID, indicate that low- velocity areas (low stress) are associated with mine workings and high-velocity areas (higher stress) are associated with areas where no mining has taken place. A high stress gradient was identified in an area where ground failed. From this tomographic survey, as well as four earlier surveys at other deep underground mines, a method was developed to identify relative stress in remnant ore pillars. This information is useful in making decisions about miner safety when mining such ore pillars.

Jan 1, 1996

By Andre Zingano

The variation in pillar behavior at underground coal mines working in the Bonito coal seam is observed in both research and mining company case studies. There is no consistency in pillar behavior, as it varies from mine to mine. In some cases, it is possible to find rib yields for both excavation modes and pillar sizes. This paper?s objective is to investigate pillar behavior for different load conditions and pillar sizes. Three-dimensional numerical simulation models considering these factors were built. A matrix was then assembled to compare pillar behavior between loading conditions, as well as between different pillar sizes with the same loading condition. The results showed some pillar rib plasticity due to vertical loading and stress relief independent of the pillar size and load. For the same load conditions, the yielding thickness is the same for different pillar sizes.

Jan 1, 2012

By Gilles Rousset

This paper presents laboratory experiments conducted on hollow cylinders samples. The advantage of such a geometry is to approach in situ conditions around cylindrical openings (lined galleries, boreholes, ...). Many authors have been interested in this kind of problem, especially for borehole stability applications (for references see Guenot 1987). However, as long as we know, time-dependent behavior has not been well studied. For this purpose, we have set up two different types of tests on a deep clay : - Quick unloading test, to assess the influence of unloading rate on mechanical response and the failure modes. - Creep and relaxation test, to compute the time dependent overall deformation of the hole wall as well as to plot long term convergence-confinement pressure curve. The experimental results are then compared with those given by a theoretical model developed in our laboratory, well fitted with the tested material.

Jan 1, 1989

By John Ellenberger

The National Institute for Occupational Safety and Health (NIOSH) has collected pillar and span data at 34 stone mines in 10 states to develop pillar and roof span design guidelines for underground stone mines. Pillar, floor and roof conditions each contribute significantly to the overall mine stability. The roof may be stable for a century, or it may appear to be stable but fail with little warning. Clearly, an assessment of the mine roof is critical to the safety of these operations. However, up until now, the assessment of the mine roof came primarily from exposures in roof falls or portal areas. This provides only limited information, and a more proactive approach is needed to assess changing mine conditions. A separate effort was undertaken to examine the roof structure with the use of a borescope. Numerous physical and geologic roof structures were observed with a stratascope/borehole video camera. The objective of this work was to develop a technique of assigning numerical values to features seen within the mine roof and apply those values to formulate a roof stability evaluation. Such features as changes in color, grain size, and general lithologies are readily observed. Minor structures in the rock, fossils and fractures are also readily identified. Each feature may have a variable and site-specific impact on roof quality. A number of mines were visited and a series of holes were borescoped in each mine. The features identified in the roof were classified and potential for roof damage related to each feature was assessed. A process is presented that relates the structures and their locations to provide a numerical value, or roof quality index that can be used to assess roof stability.

Jan 1, 2009

By Rudi Podjadtke

In a short chronological review the development concepts and improvements in steel roadway support are shown. The successful standardization concept of RAG Deutsche Steinkohle and currently used support systems are important topics. The history of optimizing the material properties for the steel arch support with different alloys up to the tempering used today is discussed. The present-day application of the steel support is additionally presented. Today, it represents a system component of modern roadway support also for highly stressed roadways. In addition to the yielding roadway arch support, this overall system - the combination support - consists of the additional components of a rockbolting system and concrete backfilling. The comparison of the application areas for each individual partial system with the overall system illustrates its high performance capability. Actual practical experience with the state of the art typed steel arches are pointed out exemplarily. Understanding the complete system permits the selection of the economically optimal support for all conditions.

Jan 1, 2008

By Andrzej Walentek

This paper presents the results of numerical modeling of the fractured zone around longwall gateroads. The numerical computations have been based on the results of underground measurements of the fractured zone around longwall gateroads, which were performed for various geological and mining conditions and measured with the use of the endoscopic method with a digital camera. Having results of the underground investigations, trials of duplicating them by the Finite Element Method using software PHASE and the Hoek-Brown failure criterion were performed. In order that the fractured zone predicted by the model-based computations closely simulate that measured underground, some selected parameters in the Hoek-Brown failure criterion were modified based on the earlier determined relations used for prediction of the roof-to-floor convergence in longwall gateroads. As a result, the model-based computations produce results very close to those obtained from the underground measurements. Determination of the fractured-rock zone around the mine roads is of great importance to mining practice, especially in planning and designing supports for longwall gateroads. The influence of the front abutment pressure causes the fractured rock zone around the roads to increase and results in an increase of support load. Moreover, proper determination of the fractured rock zone is one of basic elements in the process of planning roof bolting for mine workings.

Jan 1, 2009

By Jian Wu

In this paper, the surrounding rocks and the supports in a longwall are taken as an integral, i.e. a system. The structural characteristics and behavior of the system are discussed based on in-situ observations. A set of equations, which describe the interaction among the support, immediate roof and main roof, are developed. These equations can be used to design the longwall powered supports more reasonably and economically.

Jan 1, 1989

By David Allen

Cable bolting is a relatively new strata reinforcement technique that has been used successfully in Australia and the United Kingdom. Jim Walter Resources, Inc. has examined the principles and can visualize its useful application in many areas, such as: a) Longwall pull-out areas, b) Roadway junctions, particularly those involving yield pillars, c) Rib reinforcement, and d) Possible replacement of cribbing in roadways, especially longwall tailgates. This paper describes the conditions which led to cable bolt testing, the results of tests conducted to date, and conclusions about the direction that Jim Walter Resources, Inc. is heading as far as testing and potential applications are concerned.

Jan 1, 1994

By Gregory M. Molinda

Historically, miners have known that roof rocks originally composed largely of mud were prone to slaking and deterioration when exposed to water and humidity. Mine Safety and Health Administration (MSHA) records show that roof falls are more prevalent in summer and late fall. Field data shows higher bolt loads and increased room convergence in summer months. Laboratory data shows that very high internal pressures can be generated by significant strain in clay-rich rocks. In summer months humidities ranging from 70-100% can cause rock strains up to 7%, and rock pressures of 14,000 psi, more than enough to break apart weak shales and fireclays. The National Institute for Occupational Safety and Health (NIOSH) conducted wet/dry immersion cycling of clay-rich rocks. Results show that the rocks most prone to moisture deterioration are fireclays, claystones, and sandy shales, all of which have disrupted bedding. Of the 7 mudrocks with a weatherability index above 40%, none showed consistent fissile bedding. Black shales were surprisingly resistant to wet/dry water immersion cycling. Generally, mixed rocks (stackrock), typically susceptible to horizontal stress, are more resistant to moisture-deterioration. Mine roof rocks tested with moisture sensitivity ratings above 50% (moisture sensitivity index ranges from 0-100 with 100 being the most sensitive) all came from mines which had roof skin problems and used supplemental support to prevent rock fall injuries. Some roof rocks showed lateral variability of moisture sensitivity values, suggesting the need for more samples in highly varying roof rocks. Swelling strains of mudrocks showed that almost all of the swelling occurred in the first 24 hours after immersion. The wet/dry immersion cycling test used provides an accurate, quick and inexpensive method for estimating the moisture sensitivity of mudrocks. With this information mine operators can begin to anticipate hazardous ground and prepare appropriate roof support.

Jan 1, 2006

By Dave Minney

The South African mines health and safety regulations require that mine management establish a quality management system for rock support material. Quality control of resin capsules used as a support medium in South Africa is specified under SA National Standards No 1534. Experience has shown that this specification, while addressing the chemical and physical aspects of the products, but does not address the required performance criteria. In order to address this shortcoming, the industry has put a lot of emphasis on short encapsulation pull tests, performed insitu, in the underground workings of the mine. This is also fraught with many shortcomings, particularly as regards site availability, cost and repeatability of results. To try and address these issues, the Department of Mechanical and Aeronautical Engineering at Pretoria University were approached to develop equipment and machinery that could produce reliable, repeatable results in a laboratory environment which reasonably simulates installation practice underground. The test method is based on the ASTM F432-95 Strength Index test, but modified to use push test rather than pull tests. The paper describes development of the test method and the preliminary results and findings of the work.

Jan 1, 2007

By Michael Alber

Coal mining by the longwall method typically causes seismic events. This paper describes the research on mining induced seismicity around two specific longwalls at 1100m depth under several old longwalls. A local network featuring 21 geophones has been installed, underground core drilling and an extensive rock testing program were executed. A rock mechanical model featuring a multi-layer strata was created for use with numerical analyses. Seismic events were localized and three different event types are described. Focal analyses yielded distinct modes of failure. Those types are explained by different failure mechanisms, namely fault activation, remnant pillar punching and beam failure. The use of rock mass classification, rock mass strength criteria and in situ stresses together with 2D and 3D numerical analyses allows evaluating the findings from seismology approaches. Conclusions are drawn that the orientation of longwall with respect to the major horizontal stress orientation plays an important role in mine induced seismicity.

Jan 1, 2008

By F. N. Voskoboyev

The suggested new method for control of geomechanical state of undermined rock mass ensures, as a safety measure for the earth surface protection, the decrease of deformations by 2,5 - 10 times in mining the single seam, and by 1,5 - 5 times - in mining bed series, i. e. approximately within the seam ranges as in the application of full packing with various compressive properties or partial extraction of resources over the area with different coefficients of extraction. It should be noted that this new method has the following advantages o\w rhr. conventional methods: a) the decrease of the packing area and packing works volume by 2 - 4 fold including the operating and productive expenses; b) the elimination of mineral losses due to the increase of extraction coefficient up to 100 5%; c) rock utilization from workings drivage by its placing in the mined - out space. Perspective field of application of this method: disconservation of mineral resources in the left protective pillars of various designation.

Jan 1, 1996

By S. E. Phillipson

Underground mine mapping is a critical component of understanding the controls on ground instability. Many relatively localized examples of ground failure are associated with geologic features, such as faults, joints, compaction zones, or sedimentological transition zones. In contrast, long-running, directional roof falls are associated with regionally directed horizontal stress fields, which are induced by tectonic plate interactions in the earth?s crust. When stress-related features are distinguished from geological features, underground mapping can be an effective method for inferring the direction of horizontal stress at individual mines. Comparisons with data compiled in the World Stress Map confirm that underground mapping can be a valid method for determining the orientation of maximum principal horizontal stress at a variety of scales, ranging from individual mines to an entire mining district or coal basin. Comparisons are presented between the maximum horizontal stress directions inferred by MSHA?s Roof Control Division through underground mapping and the azimuths of maximum horizontal stress in the World Stress Map database for North America?s Pennsylvanian-aged Appalachian, Illinois, Black Warrior, and Arkoma Basin coal fields. The comparison indicates that azimuths are similar for both data sets, even where variations in the direction of horizontal stress are present. It is interpreted that inconsistencies in direction are attributable to near-surface affects such as deeply incised stream valleys, or to fault zones that represent heterogeneities in the crust.

Jan 1, 2009

By Robert Anderson

Advance knowledge of roof conditions can lead to improvement in roof control strategies that will reduce roof falls and ultimately will reduce injuries to mine workers. J.H. Fletcher and Company, in cooperation with West Virginia University, has been developing a system to meet these needs by collecting torque, thrust, and rotation speed data during drilling operations. Recent improvements in analysis algorithms to detect anomalies in the roof structure as well as various display enhancements for real time mapping and evaluation of roof structures have been incorporated into current Fletcher Information Display system. The unit has also been housed in an explosion-proof container to allow use in coal mine applications. Recently, the system has undergone extensive field trials in several limestone mines and one coal mine. During these trials, the National Institute for Occupational Safety and Health assisted Fletcher in verifying the accuracy of the roof mapping capability of the system by comparing the display information to bore hole scoping observations and drill corings. It was concluded from this assessment that the intelligent drilling system can complement scoping and core analysis to provide a more complete picture of roof strata and is capable of seeing features or conditions that are not always obvious in these more traditional methods.

Jan 1, 2007

By Chris Mark

Successful longwall mining requires a stable tailgate entry. Gate entry performance is influenced by a number of geotechnical and design factors, including: - Pillar size and pillar loading; - Roof quality; - Floor quality; - Entry width; and, - Artificial support (primary and secondary). This paper describes a comprehensive, practical, design methodology, based on statistical analysis of a nationwide data base of longwall ground control experience. Geotechnical surveys were conducted at 44 U.S. longwall mines, and underground observations of site geology, entry conditions, and support design were recorded at each mine. The observations were combined with discussions with mine personnel to identify 69 longwall gate entry designs as satisfactory, unsatisfactory, or borderline. Only conventional longwall designs, in which the pillars are expected to carry the full abutment loads, were included in the data base. Designs which employed yield pillars only were excluded. The case histories were characterized using five descriptive parameters. Pillar design was described by the Analysis of Longwall Pillar Stability Factor (ALPS SF). A major new contribution is the Coal Mine Roof Rating (CMRR), a rock mass classification system that quantifies the structural competence of bolted mine roof. Other quantitative measures were developed for primary support, secondary support, and entry width. Multivariate statistical analyses indicated that in 84% of the case histories the tailgate performance could be correctly predicted using just ALPS and the CMRR. Most of the misclassified cases fell within a very narrow borderline region. The analyses also confirmed that primary support and gate entry width are essential elements in successful gate entry design. The relative importance of the floor and of secondary support could not be determined from the data. Based on these results, a simple equation was developed to guide the design of longwall pillars and gate entries: ALPS SF,, = 1.76 - 0.014 CMRR Where: ALPS SF, = ALPS SF suggested for design. Guidelines for entry width and primary support density, as related to the CMRR, are also provided.

Jan 1, 1993

By Kevin M. Connor, Malcolm J. McPhersqn

Examples are presented in which Time Domain Reflectometry (TDR) was employed to locate deformation of rock masses induced by mining. The first example involved motoring the propagation of overburden fractures above a longwall coal panel and the second example involved the we of a)R to monitor rock mass deformation in the vicinity of a strip mine highwall. Bock mass deformation, strata separation and large block movement generated strains and failure along coaxial cables which were installed in drill holes and the TDR reflections generated by these strains and failures were monitored. Analysis of field data and a preliminary laboratory test indicate that it may be possible not only to locate rock mass movements but also to quantify these movements with TDR data.

Jan 1, 1984