Search Documents

By Paul Hagan

A diverse range of rockbolt designs and resin anchors are available for use in underground mines. Despite their wide spread use, the factors that affect the performance a rockbolt is not fully understood. The laboratory-scale rockbolt test facility at the UNSW Mining Research Centre is being used to gain a better understanding of the behaviour of rockbolts leading to an improvement in ground support. A test program investigated the nature of load transfer between a fully encapsulated rockbolt and the surrounding rock mass. It was found that with all other factors held constant, there were differences in the behaviour of load transfer depending on the method of loading. The typical pull-out arrangement as used in most field test work resulted in a different load transfer function to that observed when the load on the rockbolt was induced through bed separation.

Jan 1, 2004

By Mietek Rataj

Installation of pre-tensioned Strand Bolts i.e. resin grouted cable bolts is very common now in Australian coal mines. A short historical development of this type of rock reinforcement is outlined Various systems have been developed to apply 20 to 25 tonnes of pre-load to these bolts but there are still some technical problems which have to be overcome. One of the major problems encountered is bleed off tension which is highly undesirable as required "over loading" rocks the immediate roof thus inducing fractures iii weak strata. The major reason for the loss of tension apart from the design of the tensioning jack, is the design of the conventionally used barrels and wedges. Due to a roof plate tilting during tensioning the cable moves out of the barrel centre which impedes proper positioning of the wedges and subsequent excessive return of the cable once load of the jack is released. This problem has been largely resolved by the design of a special barrel having a centralizing rim allowing for significant reduction of the toss of tension. KEYWORDS: Pre-tensioned Strand Bolts, Cable Bolts, Bleed off Tension, Tensioning Jack, Loss of Tension

Jan 1, 2002

By Richard R. Wilding

The United States Coal Mining Indus- try had the opportunity to greatly improve their roof control techniques during the nineteen seventies by the use of fully grouted resin roof bolts. This new tool was first approved for underground coal mines by M.S.H.A. ten years ago and during the next decade has been perfected to meet many problems previously thought to be unsolveable. The initial approved cartridge was very similar to the ones used in Europe in the nineteen sixties and since then has undergone a great deal of modification for our mines. These refinements in cartridge construction have been obtained by the close cooperation of resin manufacturers with mining personnel in perfecting pro- ducts customized to particular needs. This type of continuing program naturally necessitates a responsibility upon the resin anchor manufacturer to maintain a competant technical department. These roof control technicians by constant exposure to many of the most demanding underground problems, have developed through the years into leaders in successful applications. Today, Celtite has over twenty technically trained underground technicians with an accumulation of over one hundred years experience in resin anchors. Our documented technical reports are in excess of five thousand, involving over six hundred mines representing every major coal mining area in most mineable seams. This department has been the implement used to work with our research and development people in perfecting a continual line of improved resin anchors. This program has been a significant factor in leading the resin anchor industry into a position where approximately one third of the 1980 under- ground coal production used the fully grouted system. However, as gratifying as this accomplishment is, our experience has lead us to believe that there is an additional demand for a roof control system capable of combining the mechanical bolts ability to apply tension with resins proven superiority in anchoring. A significant number mines visited during the last decade had problems that we believed could be better answered by applying tension rather than the fully grouted approach. In most in- stances, their current mechanical installations were doing an adequate job until anchor slippage occured. Fully grouted systems solved this bleed-off problem. However, an acceptable number of falls still occured. In these some- what unique areas which we believe may amount to as much as fifteen percent of the total bolt installations, the need for improved anchors was a necessity. In developing this program we listed the ultimate requirements necessary for both the bolt and the anchor. These are for the bolt: A. Have one end manufactured so it can be grouted to the mine roof with polyester resin, obtaining a variable length from 12" to 36". B. Have a mechanism which allows the operator to tension the roof from zero to 10,000 psi. This mechanism should indicate if the roof is in compression and the bolt in tension. C. Have a mechanism which allows the operator to thoroughly mix the resin. D. The head of the bolt should not extend below the roof line any more than a normal mechanical bolt. E. Not require any extra tools for installation. F. Be bendable for use in low seam coal. G. Be durable and inexpensive. The ultimate point anchor resin should have the following characteristics: A. Have a mix and gel cycle which would compete with a mechanical bolt for speed of installation. B. Have a pull out strength in excess of a normal 5/8" mechanical bolt.

Jan 1, 1981

By Erdal Unal

In order to define the support parameters, by use of empirical approaches, it is particularly important to analyze the rock-load height that should be controlled by supports. The controlling mechanism however, depends on the type of support used there- fore, the rock loads should be treated differently. In this paper, an empirical equation is introduced which relates the rock-load height (ht) to a quantitative rock quality index (REIR), and roof span (B) as fallows:

Jan 1, 1986

By David Newman

Landslides and soil creep often occur with varying degrees of severity on steep slopes within Southern Appalachia. Ground movement may take place over years with subtle changes in topography and vegetation or it can occur rapidly in response to water inflow or disturbance at the toe of the landslide. Although the ground movement typically is restricted within the soil and colluvial layers, failure can extend into the weathered rock zone. Certain areas of Appalachia are described as "slide prone" because of historical precedent. To develop a profile of "slide prone" areas, the strength and physical properties of the soil and colluvium, topography, groundwater and surface water runoff, present and historical land use, and any surface disturbance are examined in detail. These attributes are useful in determining whether an area is potentially unstable before surface development including construction, logging, or mining. Recommendations are provided to avoid initiating ground movement concurrent with mining operations.

Jan 1, 1998

By Duk-Won Park

A vast majority of the operating longwall sections use shield-type face supports to provide ground control in the United States. As a co-operative research program between the University of Alabama (UA) and Jim Walter Resources, Inc.(JWR), a joint research program is underway to study interaction of shields with surrounding rock masses. A series of analyses on the response of shields are performed using monitored data at a longwall face in a deep coal mine. In this paper, various effects of parameters, such as leg pressure, setting load, developing load, maximum loading rate, pressure in capsule, and convergence between canopy and base, are discussed and recommended as stability indices. A microcomputer program is being developed for instantaneous interpretation of the shield monitored data, and for giving warnings of potential problems. The preliminary results define the effects of the setting load, developing load, and rate of developing load or leg closure rate. The objective of the study is to understand the shield characteristics and their interaction with surrounding strata in real time, then develop a reliable program for maintaining longwall stability.

Jan 1, 1992

By Jinsheng Chen

To maintain the stability of longwall tailgate entries, they have to be supported by not only the primary roof support but also the secondary roof support due to the impact of the longwall mining¬induced abutment loads. Depending on the mining condition of a typical coal seam and its distance from the previous panel's gob, the longwall tailgate entry is often reinforced by the secondary roof support in the form of standing supports and/or cable bolts or trusses during longwall retreat, Even though lots of research work has been done to study the behavior of different standing supports in the laboratory. their function and requirements for a typical mining condition are still not fully understood due to lack of field data and correct assumptions about the behavior of the already-bolted entry roof under mining-induced abutment loads. Therefore, the application of the secondary roof support for tailgate entry roof control is still limited to trial and error, which often results in either higher cost for tailgate roof control if the design is too conservative or more production delays due to roof falls in the outby tailgate entry if the design is inadequate. To have a better tailgate roof control with reasonable roof control cost, RAG American Coal, NIOSH, and HeiTech have been conducting a joint research project to monitor actual roof loading, roof deformation, and entry convergence in the tailgate entry of 10 North panel at RAG Emerald mine. The actual roof loading data are used to calibrate and improve the roof control model for longwall tailgate entries, which has been developed by RAG American Coal, and to further reduce the roof control cost for longwall tailgate entries. The authors in this study attempt to discuss the Roof Control Model developed by RAG American Coal. in which some guidelines or important parameters for designing the secondary roof support for longwall tailgate entries are proposed.

Jan 1, 2003

By Aarao de Andrade Lima

Mechanical properties typical of coal are used in the comparisons of pillar strengths based on finite elements and the empirical equations of Holland-Gaddy, Salamon-Munro, Obert¬Duvall, and Bieniawski-PSU. A correlation among the strength parameters which are employed in the empirical equations, in Mohr-Coulomb and Hoek-Brown failure criteria is established. Emphasis is given to the important distinction between the mechanical properties of small rock specimens and those related to the rock mass. An elastoplastic version of Hoek-Brown criteria has been developed and implemented in a finite elements code. The strengths calculated using the empirical equations showed a good agreement when the ratio width by height of the pillars varied from I to 8, except for Holland-Gaddy equation which exhibited lower values. Under the hypothesis of associative perfect elastoplasticity used, pillar strength calculated using Mohr¬Coulomb yield criterion became excessively high for all the models having a pillar width by height ratio above 2. The finite elements solution based on Hoek-Brown criterion predicted strengths around fifty percent larger than Bieniawski-PSU equation when the pillars width by height ration varied from 3 to 8, showing good agreement below that range. It has been concluded that, under the hypothesis of percfect plasticity, stress analysis techniques may overestimate the strength of rock structures subjected to high confining stresses.

Jan 1, 1997

By Francis Kendorski

A longwall coal mine in Appalachia about 1,500 ft deep encountered a fault while developing a new longwall panel. The fault extended from mining depth to the surface near a secondary road and drainage. The fault was located inside the anticipated angle of draw within the mined panel and gob. The fault extended vertically out and up, away from the panel, caved zone, and gob at nearly the angle of draw: the fault very nearly following the angle of draw. It was initially thought that "fault reactivation" could possibly occur. Fault reactivation is the phenomenon of having mining subsidence localized along a fault leading to a "reactivation" of the fault and shearing and displacement along the fault. Such fault reactivation would disrupt and deform the fault plane beyond the normal angle of influence of the subsidence trough, and may provide a conduit for any ground and surface waters to reach the mine. We contacted all operators of longwall mines in Appalachia to determine if any Appalachian longwall mines had ever experienced fault reactivation, and teamed that none had experienced the phenomenon. After studies of possible water intrusion quantities and rates based upon in-fault pump tests, which indicated that water intrusion rates should be manageable, and the prior experience that faults in this particular area were usually barriers to water flow, mining proceeded with caution and monitoring. Mining was successful with no noticeable increase in water inflow rates, and no measurable off-setting of the fault exposure on the surface. It can be concluded that the fault did not reactivate due to its relationship to the mining sequence.

Jan 1, 2003

By M. Bouteldja

A finite element modelling approach is developed for the evaluation of the mechanical performance of cable bolts supports in underground mine structures. The modelling approach permits the simulation of any arbitrary number or pattern of cable bolts, that can be either partially or fully grouted, with or without end plates. The modelling technique used treats each cable bolt as a set of bar elements representing the steel cable. The bond stiffness characteristics of the grout bolt interface are represented by shear springs uniformly distributed along the cable length. Coupled with a simple linear elastic analysis, this technique can serve as a dedicated numerical model for cable bolted excavations. The application of the model is illustrated with two case studies: one for a hard rock mine and another for a coal mine.

Jan 1, 1999

By Winston Gale

This paper is presents a summary of recent investigations into fracture and caving about longwall panels. The results of these investigations indicate that rock failure initiates well ahead of the longwall face. Rock fracture typically forms in response failure through the material and bedding planes. Tensile fractures also form in massive units. These fracture patterns typically create a fracture network which determines the caving characteristics encountered at the faceline. The action of longwall face supports under such conditions is to maintain confinement to the fractured ground and develop a consistent caving line, The confinement developed above the canopy under these conditions can be variable on a shear by shear basis and the operational face support procedures play an important role in stability about the face area.

Jan 1, 2004

By John C. Stankus

ldentifcation of potential roof problems in coal mines has long been a complex issue due to the wide variety of mining and geological conditions. It is well known that mine roof falls are related to many different factors such as roof strata properties, sandstone channels, regional and localized horizontal stress, vertical stress, and tectonic stress. Many times, a combination of these factors causes roof problems. Through years of ground control experiences, Keystone Mining Services LLC, (KMS) has developed a Roof Instability Rating (TUR) system to predict potential roof problems. The first RIR analysis was presented at the 19th Ground Control Conference (Watts, et al., 2000). The RIR system includes: quantifying each individual factor, weighting each factor, combining individual factors, finalizing the RIR, and setting the criteria for the areas where special support is needed. In this paper, the application of the Roof Instability Rating (RIR) system at Enlow Fork mine will be presented.

Jan 1, 2001

By Ross Seedsman

There are many models for how roof bolts behave, one of which is prevention of shear along bedding. The basis of this model is that a roof beam will not delaminate if bedding parallel shear can be prevented. A key point in such a model is that bedding discontinuities are present naturally in the roof and that mining induced stresses do not generate new surfaces. The presence of these discontinuities means that the rock mass must be modelled as a transversely isotropic material if continuum codes are used. A limit-equilibrium type design method for specifying roof bolts is being developed using voussoir beam and excess shear force concepts. The method incorporates much of what operators know intrinsically about roof reinforcement, and allows mining engineers to focus on the key uncertainty - the frequency and location of bedding surfaces in the immediate roof. Areas where more research is required are highlighted.

Jan 1, 2000

By Tim Ross

Slurry injection into mined-out panels is an attractive alternative for disposal of coal preparation plant fines. however, in areas where surface subsidence cannot be tolerated, either by law or necessity to protect surface structures or aquifers, special consideration trust he given to the effect of slurry injection on panel stability. Slurry injection can lead to panel failure and unplanned subsidence by degrading roof, pillar, and floor strength. Water degradation is of particular concern where clay is present in the floor. Recently. unplanned subsidence related to slurry injection occurred at an Indiana room-and-pillar coal mine subject to weak floor conditions. This paper discusses the efforts of the mine operator to determine the causes of the panel failure and to design panels and injection procedures to allow for future economic slurry injection without subsidence. The numerical and empirical/analytical techniques applied give the operator a rational approach to pillar panel design for future injection panels under various cover depths and weak floor conditions.

Jan 1, 1998

By Jeffrey K. Whyatt

Estimation of the initial vertical stress carried in a coal seam is an important first step in virtually all methods of evaluating the required size of pillars in coal mines. Such estimates are a trivial exercise in coal fields overlain by gently undulating topography. The LaModel program is easily and routinely applied in such cases to efficiently estimate mining-induced stresses throughout the coal seam. However, application of LaModel to coal mines operating under rugged topography and/or in tectonically disturbed regions is more difficult. LaModel estimates stresses in a twostep process. Topographic and multi-seam mining effects on insitu stresses are estimated in an initial step, and then mininginduced stresses are estimated in an independent second step. A LaModel program function has recently been introduced that decouples these two steps, allowing in-situ stresses to be directly entered from a file rather than calculated. One application of this function is to streamline sensitivity studies by avoiding repeated recalculation of in-situ stress. The function also allows importation of in-situ stress estimates developed by other means. There are no constraints on the imported stress field, which may include significant stress perturbations due to topography, faults, etc. Hence, the range of geologic environments that can be examined by LaModel is significantly increased. This study uses the new decoupling function in an exploration of in-situ stress estimation in mountainous terrain. One option is to use the topographic stress estimation feature included within the LaModel program, and the influence of important parameters in this routine is explored. Another option explored is importation of results from a detailed volume element model. Results of this study suggest that the method used to estimate in-situ stress, and the details of its execution, can have a significant impact for mines in mountainous terrain with strong overburden. More generally, decoupling is an efficient and flexible function that should be considered for most design studies.

Jan 1, 2011

By Peter Cain

In 1993 an opportunity presented to monitor the effects of undermining an abandoned roadway by a longwall panel in the Sydney. N.S. coal field. Interaction subsidence data was collected by survey leveling to benchmarks in the undermined gateroad as well as by a standpipe system equipped with 15 vibrating wire piezometers measuring changes in elevation in the gateroad relative to an outby header tank. The piezometers were monitored at 30 minute intervals using a datalogger. while the leveling surveys were conducted weekly over the life of the project. The monitoring program resulted in the collection of a very large both of data. relating vertical subsidence to the relative position of the underlying face. The most basic analyses derived a travelling subsidence curve from the leveling data only. which hinted at a relationship between rate of extraction in the panel below and the amount of strain developed in the undermined strata. The complexity of the relationships between the amount of subsidence obtained, the location of' the individual monitoring stations, the rate of face advance below and the potential for "periodic" subsidence due to geological conditions has made analysis difficult. and the amount of data has compounded this problem. Recently. an analytical approach using a commercial neural network analysis package has been applied. which appears to have resulted in the ability to draw sonic meaningful conclusions from the data set. In this paper a short history regarding the collection of the data set is followed by a brief' description of neural networks. This is followed by a description of the several analyses performed. some of the results obtained, and conclusions drawn.

Jan 1, 1998

By Craig Collins

The objective was to develop a Real Time Drilling Display System for Rotary Roof Bolting using Analyzing Software to display mapped holes as they are being drilled in real time. The Analyzing Software was developed to analyze and interpret drill sensor data produced during a rotary drilled roof bolt hole by using algorithms and drill sensor data trends to find and locate roof separations or voids. After this software was validated through lab and field testing, its application needed to be tested in a production environment. However, the current method used to record the drill sensor data proved to be cumbersome for the mine to use on a continuous production basis. With different more practical mediums being explored and considered, a Drilling Display System was developed that will both map holes in real time and record the data for later review. With the Analyzing Software's current level of accuracy and with the convenience offered by the real time Drilling Display, the Drill Display System was implemented along with a test mine's current roof control plan and tested as a roof separation "Early Warning System". After installing the Drilling Display System onto a machine, input and suggestions from the mine environment were considered and design changes were made. The real world application provided a design direction that made the information produced by the Analyzing Software both convenient and significant for the test mine. Also, using the Drilling Display System increased the number of drilled holes that were both mapped and recorded. The results from studying these recorded data files lead to refinements in the current algorithms used by the Analyzing Software which increased the overall accuracy and capability of the system A fairly accurate representation of void or separation locations in the mine roof can be determined fromsensor data recorded during production bolting cycle. The immediate feedback on the local roof condition that the Drilling Display System provides, amounts to a quicker and safer alternative to the scratch hole and the video bore-scope examinations that arc performed after the bolting is completed. This project has shown that making the alternative method of examining the roof condition practical for the mine to use is just as important as the accuracy of its results. Based on the results of this field test, this or other methods of reviewing the analyzed drill hole data will be explored.

Jan 1, 2004

By David A. Newman

Strength and physical property testing of coal is conducted regularly by the Arch Mineral Corporation as part of reserve exploration. Pillar design and mine layout are the primary applications for the coal strength data. Distinct differences in pillar behavior were observed during longwall mining at a mine in Southeastern Kentucky. Horizontal and vertical variation in both triaxial and uniaxial compressive strength was observed within the four (4) benches of the Harlan seam. Similarly, geographical variations in coal strength were noted across the Harlan seam reserve. During the past three decades substantial research efforts have been focused upon coal pillar behavior and the refinement of pillar design methodologies. Ironically, little attention was directed to integrating the variability of coal strength into pillar design. The authors examine, through the presentation of case history data, i) typical industrial practice with respect to establishing a database of coal strength for use in pillar design and stability analysis, ii) approaches in which the observed variation in strength in the Harlan seam is integrated into pillar design and stability analyses, and to iii) propose standards for coal cube testing

Jan 1, 1993

By K. Itakura

Information about geostructure for effective rock bolting must be obtained before setting the bolt into rock in a coal mine roadway. Especially, rock type variation and distribution of discontinuities such as layer boundaries, and separation of strata and cracks all represent indispensable knowledge. To achieve in-situ evaluation of roof rock, we developed an MWD (measurement while drilling) system using mechanical data from a drilling machine for rockbolt. System hardware detects torque, thrust, revolution, and stroke of the machine, and software analyzes the mechanical data log and displays locations of discontinuities using Neural Network techniques. Also, this system is able to estimate roof rock 3-D geostructure for varied rock types and discontinuity distribution in cases of a drill hole array arrangement in roof rock. We conducted a feasibility study for it using hydraulic drilling at roadways of the Taiheiyo Coal Mine, Japan. Simultaneously, some core drillings were also performed to confirm system analysis data. For core samples, distribution of cracks was observed and the borehole wall was investigated by OFS (optical fiber scope). Must discontinuity locations estimated from roof logging were conformed with data obtained from core inspection. However, the core sample contained a number of cracks which were not found in the mechanical data log. This indicates that additional cracks were generated during and/or after core drilling by the influence of rotational force of the machine and water supply. Furthermore, in comparison with the OFS image, resolution of the discontinuity's log estimated by this system was clarified; that is, it is difficult to detect small size cracks (hairline cracks) from a mechanical data log and the core inspection by OFS. This paper outlines the new hardware system for hydraulic drilling machine and compares the discontinuity map obtained from the software system with drilling core inspection.

Jan 1, 2001

By Robert L. Schmidt

The support of underground openings by water is a natural phenomenon. Surface sinkholes, such as those that occur with some frequency in Florida, are attributed to a lowering of the water table resulting in the draining of existing limestone cavities. This withdraw the natural support and causes the surface subsidence. The role of water as a ground support medium was demonstrated in a mining situation during Bureau of Mines research on borehole mining of phosphate in St. Johns County, Florida. The borehole mining tool (BHT) incorporates a water jet nozzle and slurry eduotor in a single down- hole tool. The tool is lowered through a bore- hole into the ore zone, and an underground cavity is eroded by the motion of the water jet with the slurry simultaneously pumped to the surface. In addition to phosphate, the system has been successfully used in coal, oil sands, and uranium. The Florida phosphate ore is located at a depth of approximately 250 ft in strata that produce high water inflows. These factors preclude extraction by conventional methods, either surface or underground, but they present an ideal setting for borehole mining. Previous borehole mining research had led the researchers to believe that the system would only be effective in a void cavity, that is, a cavity where the water level is maintained below the water jet nozzle, so that the water does not impede the action of the let. It was soon discovered, however, that the void cavity presented ground control problems. The overlying strata started to cave soon after the support provided by the water was removed. This was an unacceptable situation as it adulterated the ore and threatened surface subsidence. Further tests wherein the size of the cavity -as reduced by cutting only a 30° arc also resulted in caving. A new concept, air shielding, was then introduced and tested. With this system, the water jet cutter was surrounded with a shroud of compressed air, thereby gaining the advantages of cutting in air while retaining the roof support afforded by a water-filled cavity. This arrangement proved to be highly successful. The air-shrouded jet was able to cut a cavity radius of about 18 ft, and the system production was 35 tph, which compared favorably to the production previously attained in void cavities. The borehole phosphate experience proves the efficacy of remote mining in a water filled opening. This system neutralises the hazards of heavy ground, and may, as in the case of the phosphate deposits, be the only viable alternative. It opens up the possibility of application in a wide range of deposits not only those amenable to hydraulic mining. Remote mechanical System might be developed using present robotics technology and then operated in water-filled openings.

Jan 1, 1986