Search Documents

By Edward Skolnik

The concept of using fluid dense media to separate heavy ore constituents from the lighter gangue dates back to 1858, when it was patented by Sir Henry Bessemer. Its use in coal did not begin until after 1917, however, when Chance invented a process (which bears his name) in which lighter coal floats in a suspension of fine sand in water while heavier refuse sinks. Conklin used fine magnetite in suspension as a medium for floating anthracite in 1922, DuPont designed a plant employing organic liquids in 1936, and Belknap used a solution of calcium chloride (which Bessemer had suggested, among other media) in 1937. Separation of magnetic media by magnetic separators from the suspensions in which they were carried was introduced in a Butler Brothers ore concentrator pilot plant in 1937. The media first used were crushed steel and various grades of ferrosilicon. Since 1940, when American Cyanamid used magnetic separators to recover and clean magnetite in a coal washing circuit, virtually all heavy medium circuits have been of that type. As long as static baths are employed, as they are in the processes above, coal smaller than 9.5 mm or 6.4 mm cannot be cleaned economically in heavy medium. The settling velocities of the fine material are very low, and consequently the time required to separate the lighter coal from the heavier refuse becomes excessive. In addition, stray currents in the vessel and the upward velocities induced to keep media solids in suspension affect the finer solids to the degree that physical size becomes a more important factor than specific gravity.

Jan 8, 1980

By Axel Nitschke, Josef Arnold

Bochum’s Underground Lot 306 was characterised by a confined site and unique tunnelling methods. A highly mechanized construction concept was developed to achieve high progress rates. Bespoke backup systems for muck disposal and material supply were used. For the first time in suburban tunnelling, wet shotcrete, batched onsite, was applied. A three-storey underground car park had to be undermined with only1.5 m of overburden and had to be lifted several times by “compensation grout in.” An existing operational two-lane metro tunnel was enlarged without any major impact on train operation.

Jan 1, 2005

By D. W. Wu, M. T. Haque

A novel impedance probe has been commissioned specifically for capturing fast dynamic information about filtration processes. It provides an attractive alternative to more complex measurement techniques in situations where the slurry system is primarily one-dimensional. The probe can monitor mud-line, slurry densification and drainage. Dynamic variations in cake permeability are obtained by combining dynamic mud-line information obtained with the probe and filtrate rate data derived from a leaf test apparatus. The measurements are re-viewed in relation to micro structural measurements obtained on iron ore filter cakes. The practical significance of these measurements for optimization of the filtration process is discussed.

Jan 1, 2000

By M. S. Ellis, D. J. Nichols

In 1999, 1,100 million short tons of coal were produced in the United States, 38 percent from the Northern Rocky Mountains and Great Plains region. This coal has low ash content, and has sulfur content in compliance with Clean Air Act standards (U.S. Statutes at Large, 1990). The National Coal Resource Assessment for this region includes geologic, stratigraphic, palynologic, and geochemical studies and resource calculations for 18 major coal zones in the Powder River, Williston, Green River, Hanna, and Carbon Basins. Calculated resources are 660,000 million short tons. Results of the study are available in U.S. Geological Survey Professional Paper 1625-A (Fort Union Coal Assessment Team, 1999) and Open-File Report 99-376 (Flores and others, 1999) in CD-ROM format.

Jan 1, 2001

By Martin Herrenknecht

After the successful breakthrough at the end of 2006 of both TBMs into the multifunctional site Faido (MFS), in the middle of 2007 the two tunnel boring machines resumed the 12 km long section between Faido and Sedrun. In the roughly a 10 month interval both approximately 465 m long tunnel boring machines were partly dismantled, pushed through the 2.5 km long MFS, rebuilt for the new larger diameter of 9.5 m and reassembled to be ready for operation. In the rebuilding phase, improvements were made to the equipment, especially as a result of experience gained from the previous 14 km long drive in the section Bodio and taking into account the latest information regarding the upcoming 14 km section Faido. Both TBM drives are currently in the rock formations of the Lucomagno gneiss, which stretch over a section of 3.5 km from the MFS Faido to the predicted Piora Syncline. This section is divided into two fold axes of the Chièra Synform, where the Lucomagno gneiss pass from a sub-horizontal into vertical bedding. The drives, with current rock overburdens exceeding 1,500 m and, as known from the excavation phase of the MFS, in part highly disturbed rock formations, are characterized by the locally intense rock squeezing conditions with large convergences in the vicinity of the driving TBM as well as backwards due to the interaction of the two drives. High expenditure for the support measures, reduced driving performances together with extensive extra work associated with deadlines and increased costs are the result. In the paper the previous experience with the TBM drives in the section Faido and the challenges still awaiting us are presented and discussed.

By Anthony D. Hammond

The use of geographic information systems (GIS) as a tool to analyze and display data is gathering momentum in the mining industry. Of particular interest is the capability of GIS to link spatial features and tabular data. The application of GIS in underground mining discussed here concentrates on four technical areas. They are land ownership and mineral claims, exploration management, production and mine safety.

Jan 1, 2002

By J. Walden, S. Rhoades, R. E. Miller, R. Gibbs, P. Boman

Accelerometers and pressure transducers mounted in suspension components can be used to monitor the ride of haulage trucks. Presently, it is difficult to tell what caused a jolt to the truck using either pressure or acceleration data alone. When information from a Global Positioning System is recorded at the same time as shock pressures or acceleration data, then the exact location of an event can be determined. Mine management can then determine what caused the jolt to the truck.

Jan 1, 1999

By Joseph J. Zaluski, J. Steven Gardner, Marco M. Rajkovich

The telephone rings at 3:20 a.m. An exasperated voice on the other end says, “There has been a mine explosion at Mine No. 5 and we have not heard from three units of men.” Twenty-three minutes later, the phone rings again and another panicked voice says, “There is something wrong at the slurry impoundment, the pool level has just dropped five feet and we are trying to figure out what is wrong” Thirty minutes later, the mobile phone rings. An excited security guard says, “We have reports of thick black water running down the right fork and left fork of Straight Creek and both seem to be rising in the banks.” If this is not enough excitement, the mobile phone rings again. A stressed company official says, “I just heard a report that black slurry is running out of the portals of XYZ Co. No. 2 Mine, which is adjacent to our No. 5 Mine.” Is this all some kind of dream or nightmare? More importantly, though, if this happens, what do you do? Most people think: “It can’t happen to me.” But mine explosions do happen, slurry impoundments can rupture and creeks can flood with black water causing damage to others, including competitors. A mine’s response must be quick, cool-headed, calculated and effective. This article examines the issues, concerns and ramifications of this hypothetical disaster. The authors then present a systematic crisis-management response.

Jan 1, 2004

By Robert J. F. Goodfellow, William A. T. Meakin, Kevin Clarke, Eric Cole

INTRODUCTION New York City Water Supply—Background and History Since the 1840s New York City has been developing the largest, and perhaps, the best urban water supply and distribution system in the world in terms of quality and reliability. One of the engineering marvels of the modern world, the New York City water supply and distribution system serves a population of almost nine million, including residents in nearby Westchester, Putnam, Ulster, and Orange Counties of New York State. The average daily supplies presently are running at almost 60 m3/sec(about 1,350 million gallons per day). The watershed for the New York City water supply system, under the jurisdiction of the New York City Department of Environmental Protection (NYCDEP), consists of19 reservoirs and three controlled lakes, and covers an area of approximately5,000 square kilometers (about 2,000 square miles) north of New York City. The watershed total available storage capacity is about two billion cubic meters (560 billion gallons) and is divided into three reservoir systems: the Catskill and Delaware watersheds located West of the Hudson River; and the Croton watershed, located east of the Hudson River, see Figure 1. The first element of the system, the Croton Aqueduct, started operations in 1842.Through several updates and expansions, the present-day Croton system was in place by 1911, providing a potential maximum supply of about 15 m3/s (about 340 mgd). The system includes ten reservoirs and three controlled lakes. In the late 1800s, with the tremendous growth of the City, New York City water engineers began to look for additional sources. Between 1907 and 1929, the City acquired water rights and constructed a new 148 km (92 miles) Catskill aqueduct to convey water from the Ashokan Reservoir to the City. The Catskill system also included the construction of the Kensico and Hillview Reservoirs just north of the City,

Jan 1, 2005

By Kazuo Magata, Hirohiko Fujita, Masazumi Tashiro, Yoshiaki Sato, Yoshio Shinoda

The Shinkansen of the Japanese National Railways (JNR) presently in operation between Tokyo and Hakata, approximately 1,000 km, was constructed at three stages: between Tokyo and Shin-Osaka opening in 1964, Shin-Osaka and Okayama in 1972 and Okayama and Hakata in 1975. Works on the extension of 400 km from Okayama to Hakata were launched in March 1970. As construction of the undersea Shin-Kanmon Tunnel on the extension was the toughest task, requiring many, many months, the work was undertaken earlier than any other works on the extension. It was brought to its completion in June 1974 at the cost of about 22, 000 million yen. The Shin-Kanmon Tunnel is the third undersea tunnel constructed to connect the main island of Honshu and Kyushu across the Kanmon Straits. (Table 1)

Jan 1, 1976

By Natalia Konstantinova, Georgy Novikov, Pavel Rekant, Goergy Cherkashov, Olga Bogdanova

The economic interest of oceanic ferromanganese crusts and nodules is determined by high grades of major, rare and earth rare elements in these types of marine minerals [1]. Modern oceanic ferromanganese deposits have a global distribution with the largest fields in the Pacific Ocean. The Arctic Ocean still remains a poorly explored region. The first ferromanganese deposits from the deep part of the Arctic Ocean were recovered almost at the same time in 2012 both in US and Russian cruises to the Chukchi Borderland (1) and Mendeleev Ridge (2). Preliminary results of mineral deposits from the first area were reported at UMI-2012 by James Hein et al. [2]. We present here the data of ferromanganese deposits from the Mendeleev Ridge.

Sep 1, 2014

By Z. Hyder, M. Karmis

Underground or In-situ Coal Gasification (UCG or UICG), though not a new concept, is now attracting considerable global attention as a viable process to provide a "clean" and economic fuel from coal. Applying improved UICG technology to gasify deep, thin, and low-grade coal seams could vastly increase the amount of exploitable reserves. However, it is imperative that further development of this technology is based on integrating UCG practices and potential environmental impacts with accepted sustainability frameworks and processes. This paper evaluates the potential of UCG to conform to frameworks such as MMSD (Mining, Minerals and Sustainable Development), Natural Step and Green Engineering, in order to define its "sustainable" potential. The paper also discusses the potential contributions of UCG to sustainability during its design, operation, closure, and post-closure phases.

Jan 1, 2011

By D. Lawrence, H. Lawrence, G. Saevil

Plant operators in the mineral processing industry have been implementing expert systems for several years now, with the intent to increase production and reduce costs. Most systems have been installed on grinding circuits of some type and have proven that the technology is viable in that application. However, few applications on other processes have been attempted for various reasons, such as lack of reference sites, complexity of the process, lack of suitable measurements and lack of confidence in the technology. The successful application of an expert system on an Alumina Calcining kiln is the first such application in the West Indies Alumina Company (Windalco), and demonstrates how this technology can be successfully applied to other processes. The key objective of an expert system is to optimize the process. To achieve this the process must first be stabilized, followed by optimization of the operating parameters. The steps taken by this expert system to optimize the process are: • Check for abnormal conditions and deal with them using a prioritized set of special actions. • Use a selection of rule blocks to stabilize the process. • Once the process is stable, achieve additional benefits through further optimization of the process. The potential benefits that a user can expect to achieve through installing an expert system can be assessed on the basis that performance will improve from that of an "average operator" to that of the "best operator" performing at his optimum for 24 hours a day, every day. The quantifiable process benefits include: • Increased production • More consistent product quality • Reduced operating costs • Reduced standard deviation of key variables • Consistent plant operation The success of this project was measured in several ways: project implementation, realised economic benefits, and realised non-economic benefits. With a commitment to maintain the system over the long term, the longevity of the system is assured and will become an important part of the Alumina Calcining control strategy at Windalco. This paper discusses the various phases of implementing the ABB Expert Optimizer expert system, what the benefits were and the procedure that is in place to maintain the system to ensure continued long term success.

Jan 1, 2002

By P. D. Chamberlain, R. M. Nadkarni, D. J. Kinneberg

Introduction The relationship between precious metal miners and gold refiners has been uneasy over the years. Reasons for this uneasiness and lack of trust include technical factors, economics of scale, and cultural differences. Technical factors take two forms. First, concentrates, precipitates, and sponge produced at the mine site are notoriously difficult to sample. A nonrepresentative sample can be the cause of misunderstanding and distrust. Dote, however, is relatively homogeneous and can be correctly sampled and analyzed with greater reliability. Second, the technology and chemistry of fine gold and silver production is complex and quite different from dote production. Most mining companies are content not to be involved with additional processing steps. From the standpoint of process economies, it is easy to see why miners and refiners are separate groups. Mine location is dictated by the natural occurrence of ore bodies. Heavy capital investment requirements for infrastructure in remote locations usually limits companies to produce the first marketable product from a mine. Beyond that point, the economies of scale and large capital investments for refineries generally dictate that the outputs of several mines be combined to feed a single refinery. The refin¬ing process is so complex that refineries are generally built in larger cities with a skilled labor pool. Therefore, only the largest mines can afford to refine their own output. Lastly, there are cultural differences between the miner and the refiner. The miner, particularly the small gold miner, is by definition a risk taker in a risky business. Refineries, on the other hand, have historically been operated under legal or implied monopolies approved by the government. The government is interested in owning gold, either for currency reasons or because many national mints are major users of gold coins. It is not surprising, then, to find that miners may regard refiners as part of an unresponsive government bureaucracy or, worse, as "city slickers." It is easy for the two groups to distrust each other with these different backgrounds. The interface between miner and refiner does exist and affects nearly all precious metal mining companies and most refineries. This paper discusses the technical and economic aspects of the interface. It points out how both parties can improve the relationship. Technical interface Precious metals selectively dissolve to produce a pregnant solution. They are then recovered from solution by zinc precipitation (Merrill-Crowe process) or by absorption onto activated carbon. This is followed by stripping and electrowinning. At this point, the mining company must decide whether to ship precipitates (or sponge) to refiners or to produce a dote. Some factors the company must consider are the ability to sample precipitates, concentrates or sponge, security of storage, and production rates. An important factor is the incremental cost (capital and operating) of converting precipitates or sponge into dote at the mine. Generally, mines prefer to melt precipitates or sponge to dote to avoid prob¬lems associated with sampling them. There are three types of fur¬naces used by mining operators to melt precipitates to dote. The first and most widely used is a sil¬icon carbide crucible heated ex¬ternally with a gaseous liquid fuel. The crucible is easy to use and slag can be skimmed before pouring dote. This simple system is capable of handling 1 t/a (32,000 oz per year) gold. It could cost as little as $20,000. More complex systems could cost up to $200,000. The second type of furnace is the gas- or propane-fired rever¬beratory furnace. This is usually used only by large-scale opera¬tors in the silver business. Precip¬itates in reverberatory furnaces come in direct contact with the flame. The large volumes of flue gas can carry significant amounts of dust and fume that must be re¬moved from the gas before dis¬charging it to the atmosphere. In the days when the Rand re¬finery in South Africa used reverberatory furnaces, the silver leaving the furnace in the form of vapor and fume was estimated at 2.2% of the total silver charged to the furnace. The gold in the gases was about 0.03% of the gold charged. Most of this silver and gold was recovered in the exhaust gas scrubber system. These scrub¬ber systems can be more costly than the furnace itself.

Jan 10, 1986

By Andrew E. Nevin

The government of India convened a precedent-setting meeting in New Delhi on Nov. 12, 2001.The meeting brought together regulators and the mining industry in an attempt to fix the industry’s mine development problems in that country. More than 150people attended the all-day session. Ram Vilas Paswan, Minister of Coal and Mines, chaired the meeting. Ravi Shankar Prasad, Minister of State for Coal and Mines, was also present. The secretary of the Department of Mines and the Joint Secretaries and Additional Secretary also participated. The Department of Mines’ mandate is for economic growth: to get new mine development going and to make investment in mining attractive for both domestic and foreign-owned companies.

Jan 1, 2002

By Les Gutzwiller

Fan applications in the mining industry have changed during the last 70 years. In 1922, J.R. Robinson authored a technical volume entitled Practical Mine Ventilation. At that time, atmospheric control had only recently shifted from natural to mechanical. The large, mechanical draft fans that were used then were centrifugal. The fans ran at low speeds, about300 rpm. Most were steam-engine driven. In the late 1920s and early 1930s, mines became larger, increasing the pressure and volume requirements of the fan equipment. Axial fans were designed to run at much higher speeds (710 to 880 rpm) and were driven by electric motors. They were also smaller and less expensive to install than the cumbersome centrifugal units. However, changes in mining have resulted in progressively higher static-pressure requirements. So centrifugal fans are once again proving to be a good choice.

Jan 1, 1999

Train services through the Channel Tunnel linking Britain and France where scheduled to be fully restored in February 2009 following several months of repairs after a major fire in the tunnel on Sept. 11, 2008. A lorry caught fire on a shuttle train carrying heavy goods vehicles bound for France through the 50-km- (31-mile-) long northern tunnel. The fire, that spread to other vehicles, raged for about 16 hours. The extreme temperatures of up to 1,000º C (1,832° F) caused extensive damage to about 600 m (2,000 ft) of the 7.6-m- (25-ft-) diameter tunnel?s concrete lining, approximately 11 km (7 miles) in from the French entrance. The Channel Tunnel operator, Eurotunnel, awarded the repair con-tract, estimated to be between ?50 to 60 million, to a consortium of Freyssinet, Eurovia Travaux Ferroviaires (ETF) and Vinci Energies. Freyssinet was appointed to look after the civil engineering works, while ETF would be responsible for track and overhead wire restoration and Vinci Energies responsible for other equipment. The technique of hydrodemolition, which uses high-pressure water jets to remove concrete from various structures, was specified as the method to remove the fire damaged concrete. Freyssinet subcontracted the concrete removal to the specialist hydrodemolition and industrial cleaning contractor Philip Lasserat.

Jan 1, 2009

By R. R. Oder, R. E. Jamison, E. D. Brandner

This paper presents preliminary test results obtained with a 0.38 kg/s (3000 lb-hr) beta prototype MagMill™. In processing Upper Freeport coal the beta prototype recovered 82% of the weight of the feed and 91% of the heat content while reducing the potential emissions of sulfur, kgSO2/GJ(lbSO2/MBtu), by 61%. Pyritic sulfur in the MagMill™ product was reduced by 78% compared to that in the feed. For all runs, the mill product was controlled between 70 to 80% finer than 74 µ particle size. Recoveries of mercury, arsenic, and selenium ranged from 35 to 45% of that in the feed. Power draw was reduced by 26% and mill throughput was increased by 9% compared to the pulverizer operating with no magnetic separator attached.

Jan 1, 2000

Even though the economy of the United States remains in recession ? or not, depending on which economist you listen to ? muicipalities still need improved transportation, water and wastewater transit systems. And they are willing to spend the necessary funds on those systems, provided they are affordable, environ-mentally friendly and sustainable. From June 20-23, professionals in the tunneling and underground construction industry from around the world gathered in Portland, OR to learn new ways of providing those systems using the latest technology available. The North American Tunneling (NAT) conference attracted 803 attendees and 108 exhibiting suppliers of equipment and services.

Jan 1, 2010

By C. L. Kosmoski

The mining industry faces many workplace hazards that are a threat to human health and safety. The Bureau of Labor Statistics has found that employees in coal mining are more likely to be killed or sustain an injury or illness than workers in private industry. These injuries are also likely to be more severe (Bureau of Labor Statistics, 2007). In recent years, coal mining injuries have attained national attention due to highly publicized disasters. Despite these threats to worker safety and health, the U.S. relies on the mining of coal to meet its need for electrical power, with42% of electricity in the U.S. generated through the burning of coal (U.S. Energy Information Administration, 2012b; United Mine Workers of America, n.d.). Furthermore, the production of coal continues to increase and reach record levels every year(National Mining Association, 2012; U.S. Energy Information Administration, 2012a). For this reason, the coal mining industry must continue to find ways to protect its workers while maintaining productivity. One potential approach to protecting workers while maintaining productivity is through improving the safety culture at coal mines. In order to achieve this culture, operators, employees, the inspectorate, etc. must share a fundamental commitment to safety as a value. This type of culture is known in other industries as a ?safety culture? and can be defined as the characteristics of the work environment, such as the norms, rules, and common understandings that influence facility personnel?s perceptions of the importance that the organization places on safety. Fundamental to improving safety culture within an organization is understanding the existing safety culture; improvements cannot be made without first elucidating areas that require improvement. This manuscript details the process undertaken by researchers at the National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) to assess the safety culture at five underground coal mines across the United States. The purpose of this manuscript is to introduce the mining industry to a multi-methodological approach to safety culture assessments. Further, it is the goal of this manuscript to highlight the value of including both quantitative and qualitative methods into safety culture assessments in order to obtain the most comprehensive view of an organization?s safety culture. Because this manuscript focuses solely on the methodology implemented, data and results obtained during the five safety culture assessments will not be presented in this manuscript, but will appear in a future publication.

Feb 27, 2013