Search Documents

By J. F. T. Agapito, R. R. Goodrich

Yield pillars have been used for many years to help reduce stresses near mine openings and improve roof and floor stability. A yield pillar is often defined as a pillar that fails but retains residual strength. Stress transfer occurs through the roof and floor after the peak strength of the pillar is reached. High stresses are transferred from around the openings onto abutments that can be barrier pillars or unmined ground. This mechanism, often referred to as pressure arching, is possible as long as the width of yield pillars is less than the critical width above which stresses cannot be carried by the overburden. Significant stress transfer also can occur due to small amounts of pillar and/or floor yielding before the peak strength is reached. This is accomplished in a quasi-elastic manner with little or no visible roof and pillar fracturing or floor heave. Long-term stability may be achieved when stresses and mechanical properties are favorable to pre-failure yielding. This paper gives practical examples where improvements in stability and resource recovery were achieved with this mechanism. Yielding was assessed by comparing measured and calculated vertical pillar stresses. Results indicated that calculated stresses in the pillars were 25 to 40 percent higher than the measured stresses, demonstrating significant arching load transfer to the abutments. Pre-failure yielding is probably often present but unintentional in both development and production areas. Better recognition and use of this mechanism should lead to improved designs as mines become deeper.

Jan 1, 2001

By M. Okido, W. Wei, L. Chai

The kinetics on the growth of Thiobacillus ferrooxidans was studied by use of series piezoelectric quartz crystal ( SPQC ). Arsenic ioninhibits the growth of Thiobacillus ferrooxidans, which is consistent with the previous results by other measuring method. This further demonstrates that the SPQC can monitor the chemical activity of the growth of Thiobacillus ferrooxidans. Cupric ion accelerates the growth of Thiobacillus ferrooxidans. The mechanism was discussed, it was considered that copper promotes the protein enzyme of Thiobacillus ferrooxidans, rustic yanin, to form over the range of cupric ion concentration studied. There action order of cupric ion in accelerating the bacterial growth is 0.067. The growth of Thiobacillus ferrooxidans is dependent on temperature, the apparent reaction activation energy decreases from25.56 kJ / mol to 18.32 kJ / mol because of the addition of 10 mg / L Cu(II) to the bacterial growth solution of pH 2.0 at initial inoculum of 10%.

Jan 1, 2000

By Peter Klaver

Deep tunnels have been used for decades for the temporary storage of large volumes of urban runoff, both storm water and combined sewer overflow (CSO). Tunnels are attractive because they reduce surface disruption and do double duty as storage and conveyance systems, collecting overflows from multiple locations and transporting them for treatment to various facilities. Like any hydraulic system, however, there are dynamic effects that must be fully understood during the design phase so that the final constructed product does not have unintended negative consequences. Preliminary sizing of storage tunnels is typically based on the total volume required. For example, if studies have determined that a volume of 56.8 ML (15 million gal) will provide the intended level of control, then that figure can be used, along with a preliminary idea of the desired tunnel length, to compute the required diameter. Of course, filling a long tube with water from various points along the way is not at all the same as pouring water into a bucket, and these dynamic effects require additional attention from design engineers. The rapid filling of storage tunnels can lead to the formation of bores, which are essentially moving walls of water. An open channel bore can build in height until it reaches the crown of the tunnel, at which point it becomes a pipe-filling bore. Figure 1 depicts both kinds of bores moving upwards in a rapidly filling tunnel. Bores can strike the ends of tun-nels with tremendous force, driving water and entrained air upwards into dropshafts and creating strong pressure surges in portions of the tunnel that are already filled. If the hydraulic surges are high enough to reach grade, they can cause overflows and/or damage structures at the surface. Trapped air pockets can occur through several phenomena, including the reflection of bores off dropshaft structures and the occurrence of ?premature pressurization.? The latter refers to the situation where the inflow to a tunnel is increasing more rapidly than the tunnel can convey it, such that the pipe becomes surcharged at an upstream point while points downstream are still flowing as an open channel. These air pockets are a great nuisance as they migrate toward points in the tunnel where they can rise to the surface, which are often shafts that are already filled with water (Fig. 2). The ?geyersing? that results can be hazardous and costly.

Jan 3, 2010

By V. Svalbonas, M. Fresko

The present versions of the Welding Codes, such as BS7608, have long been known to be compatible with hand computations of membrane and bending stress, rather than detailed finite element solutions. However, in the last five years, in the mining industry, this incompatibility has been largely ignored, and the code interpretations have been pushed into the realms of ground welds, residual stresses, and even flaw growth. Such techniques have to be recognized as extrapolations not necessarily sanctioned by the original code documents. The safety of such extrapolations, as they are related to grinding mill fatigue design, is investigated herein.

Jan 1, 2002

By W. Pawlos, A. Bakalarz, M. Duchnowska

This paper presents the results of an investigation into the influence of hydrodynamics on a preflotation process for the copper sulfide ore from the Fore-Sudetic Monocline deposits in Poland in a flotation machine. The main aim of the preflotation stage for Polish copper ore is to remove the easy-to-float organic matter — organic carbon — that causes serious problems in metallurgical processes. The organic matter is connected with the presence of shale ore. This paper describes the preflotation experiments conducted to investigate the effect of various stirrer speeds. The upgrading selectivity of copper and organic carbon were analyzed and compared. The results show that the effectiveness of separation between organic carbon and copper decreases with increased stirrer speed in the laboratory flotation machine. The more intensive the mixing of the flotation suspension, the lower the selectivity of the preflotation experiment. Lower stirrer speed probably provides lower mechanical entrainment and flotation of copper minerals.

By Stephen Phillips, Luigi P. Gonano

Vertical circular shafts have been proposed for multiple access to high level nuclear waste deep geologic repositories. Shaft construction is a critical path item in the commissioning of a repository. Other constraints on the shaft design and construction criteria include the lack of design precedence for long term performance and the importance of minimizing rock and groundwater disturbance. A comparative evaluation of conventional and mechanized shaft sinking techniques is presented in the context of the particular geologic and design constraints. Technical and non-technical factors for blind drilling, blind boring, raise-reaming, drill-and-blast and ream-and slash methods are reviewed for typically "hard rock" and "salt" type repository sites. Appropriate shaft designs are developed, the suitability of each method to the particular requirements evaluated and construction costs and schedules determined. The explicit appraisal of the significant design factors for each method serves as a rational basis for the preliminary selection of the most suitable sinking technique for a particular set of site/design conditions.

Jan 1, 1983

By Wojciech Klecan

Cobb County, located on the northwest side of Atlanta, GA, is continually growing and, like many other metropolitan areas, it needs to increase the capacity of its waste water system to meet future demand. The Cobb County Water System (CCWS) is the responsible agency for water distribution, waste water collection and treatment in most areas of the county. CCWS, one of the most progressive agencies in the metro-Atlanta area, is addressing its future waste water capacity needs in the southern part of the county with the construction of the South Cobb Tunnel and Pump Station. This project consists of an 8.8-km- (5.5-mile-) long, 8.2-m- (27-ft-) diameter, tunnel boring machine (TBM) excavated waste water storage and conveyance tunnel; six tangential vortex-flow intakes ranging from 1,533 to 5,700 L/s (35 to 130 mgd) peak flow capacity, two construction shafts, six 1.8-m (6-ft) finished diameter connecting tunnels ranging in length from 6 to 975 m (20 to 3,200 ft) and a 5,700-L/s (130-mgd) wet/dry pit pump station. The pump station will have a semi-circular wet well with a dividing wall that extends almost to the top of the shaft and a spilt dry well for reliable operation. Roller gates will control the flow to the wet well from the tunnel. The pump station will have six 1,420 L/s (32.5 mgd) pumps and two sets of stair wells and elevators. With a finished diameter of 32 m (104 ft) and a depth of 62 m (204 ft), this is the largest pump station shaft constructed so far in Georgia for the dewatering of a waste water tunnel. The pump station shaft was also the highlight of the well attended and successful 2009 Shaft Design and Construction Short Course held in Atlanta, Sept. 10-11. The two-day course was sponsored by the Underground Construction Association of SME and Pennsylvania State University and concluded with a field trip to the pump station shaft. The tunnel starts south of the city of Austell and finishes at the South Cobb Water Reclamation Facility (WRF), located on the banks of the [ ] Chattahoochee River just north of Interstate 20 (Fig. 1). The South Cobb Tunnel will run 30 to 137 m (100 to 450 ft) below the surface, with an average depth of about 91 m (300 ft), through metamorphic rocks (Fig 2). The construction contract was awarded to Shea-Traylor JV with the lowest bid price of $305 million and notice-to-proceed was given on July 14, 2008. Jordan Jones & Goulding, Inc. (JJG) is the project designer and performed the geotechnical investigations. Parsons/Jacobs Associates is the construction manager. The South Cobb Tunnel is CCWS?s second deep hard rock tunnel. The 15.3-km- (9.5-mile-) long, 5.5-m- (18-ft-) diameter TBM excavated the Chattahoochee Tunnel was the first deep tunnel to be construced in Cobb County. Construction began in 2000 and the project was completed four years later. It is located about 16 km (10 miles) northeast of the South Cobb Tunnel in similar geology. It was designed by JJG to meet east Cobb?s long-term waste water capacity needs and provide flow equalization to the R.L. Sutton WRF. The Chattahoochee Tunnel was named ?Outstanding Civil Engineering Project of the Year? by the Georgia Sec-tion of the American Society of Civil Engineers in 2006.

Jan 1, 2009

By Juan P. Camus

Mining is one of the oldest industrial activities. Its products are essential to modern civilization. Paradoxically, and despite a deep-rooted belief to the contrary, mining is not a lucrative industry— at least not in the aggregate. This assertion is true not only for recent years, one of the weakest periods in terms of metal prices, but also for a long time past. In 1776,Adam Smith said in The Wealth of Nations: “Of all those expensive and uncertain projects, how-ever, which bring bankruptcy upon the greater part of the people who engage in them, there is none perhaps more perfectly ruinous than the search after ... mines. It is perhaps the most disadvantageous lottery in the world... Projects of mining, instead of replacing the capital employed in them, ... commonly absorb both capital and profits.”

Jan 1, 2002

By Martin Herrenknecht

Tunnel boring machine (TBM) development continues to take on not only larger diameters, but also more difficult ground conditions. Ground conditions consisting of unstable faces with water pressures up to 15 bar have required innovative design approaches. A systems approach has been required to produce tunneling machines that can safely excavate the tunnel in an efficient, cost-effective manner that stresses production and labor saving approaches. This article reviews the current design developments and present recent projects where these most recent principles have been applied. The world?s growing population and rapidly proceeding urbanization are boosting an enormous demand for new and high-capacity infrastructures to secure the mobility of goods and people. Densely populated areas face the challenge of providing efficient traffic infrastructure such as a modern public transport system. At the same time, the maintenance and modernization of supply and disposal structures for water, sewage, energy and communication are essential. Last but not least, are supra-regional transportation routes such as long distance water diversion schemes. All of these projects are as demanding and are characterized by a tight time schedule. In this context, the demand for efficient tunnels for traffic and utility lines is increasing, as new infrastructures often leads underground because of limited space above ground. Also, tunnels are the obvious choice to cross natural barriers like mountain ranges. To handle the complex and variable geological conditions and other constraints, such as low overburden, high water pressure or long tunnel drives while facing increasing demand of a quick completion of a project, mechanized tunneling sets standards regarding safety, profitability and environmental protection in traffic tunneling projects as well as in the trenchless construction of utility tunnels. Different machine types and working principles have been developed to master various geological and hydrogeological requirements. Continuous activity in research and development leads to constant improvement of the mechanized tunneling process.

Jan 1, 2008

By Raymond W. Henn

The 32nd annual short course ?Grouting Fundamentals and Current Practice? was held at the Colorado School of Mines, June 13-17, 2011. The field demonstration portion of the course was conducted June 16 at Baski Inc.?s yard in Denver, CO. The full-scale field demonstration presents many types of drilling and grouting equipment in operation as well as numerous grouting methods per-formed under various field conditions. As part of the field demonstration, the class was shown the proportioning, mixing, testing and injection of various cement grout mixes into sand columns under controlled and recorded conditions. These sand column demonstrations have been conducted under controlled and measured conditions each year since 1999 as part of the short course. The sand column demonstrations were conducted prior to 1999, but with less quality control and minimal record keeping of the proportioning, mixing, testing, injection pressures and the final permeation results.

Jan 1, 2011

By M. Dobbins

The advent of the more efficient and effective rare-earth roll (RER) separator in the early 1980?s began a new era of dry magnetic separation. The RER units quickly became the separator of choice within the materials processing industry. Though RER separators are now commonplace throughout the world, only modest advancements have been made to the original design. This paper details recent, more significant, rare-earth magnetic separation developments. These developments maintain the best features of existing technology while minimizing shortcomings. The discussion includes discerning features that aid in better metallurgical performance. Also discussed are improved mechanical aspects that allow for both easier operation and maintenance. Performance details from various test programs are included.

Jan 1, 2009

By Horst Pöchhacker

The largest structure along the Tauern highway section between Salzburg and Villach is the 6.4-km-long Tauern Tunnel. The major geotechnical problems that came up surprisingly while driving the headings of that tunnel and their successful solution form the content of this article. A detailed discussion is presented of the special construction methods developed by systematic application of the principles of the New Austrian Tunneling Method with which even very heavily squeezing ground with large excavation areas can be mastered reliably and economically.

Jan 1, 1976

By Michael J. Robison, Wojciech F. Klecan, Robert L. Horner

Since 1928, nearly 64 km (40 mi) of tunnel have been excavated within the relatively soft Cooper Group, more commonly known as the “Cooper Marl,” for water supply and transporting wastewater in the Charleston area. The majority of these tunnels are unlined and still in operation, while others collapsed shortly after excavating. Tunnel behavior and support requirements vary considerably in this material due to differences in geotechnical properties. The 4.8 km (3 mi) long, 2.4 m (8 ft) diameter Bushy Park Water Tunnel, completed in 1997 for Charleston’s Commissioners of Public Works(CPW), required no ground support. By comparison, the 1.6 km (1 mi) long, 2.4 m (8 ft)diameter Harbor Wastewater Replacement Tunnel now under construction needs continuous support close to the advancing face, despite being located in the same geological formation. Case histories and general guidelines for designing tunnels in the Cooper Marl are presented.

Jan 1, 2001

By F. B. Kuhnow

When performing blasting operations in open pit settings, energy is released and transmitted through the geology. Some negative effects can have significant impacts on mining operations and adversely affect mine production. This technical paper presents recommendations for blast design to prevent damage due to ground motion from blasting on adjacent concrete structures of underground operations. The paper includes a case study describing a problem regarding an open pit mine expansion and asks whether production blasting will damage concrete shaft structures due to blast stress waves and blastinduced ground motion. Based on the results, a set of criteria is provided to implement in current and future mining operations that involve blasting near underground concrete structures. A set of techniques on how to improve vibration levels for safe operations is also presented. Knowledge of particle velocity and wave propagation for site-specific circumstances to determine a safe level of vibration is recommended. Emphasis is placed on making use of electronic detonators and early delay detonators to achieve successful levels of vibration. A dynamic analysis is necessary to determine if vibration from blasting can damage the concrete shaft structure. When reinforced concrete structures are subject to blast loading, both concrete and steel are subject to very high strain rates. As opposed to static loads, when subject to high strain rate loads these materials increase their strength significantly. In fact, they increase by more than 50% for reinforcing steel, by more than 100% for concrete in compression, and by more than 600% for concrete in tension. This finding is of significant importance in mining operations because it allows an increase in flexural capacity of individual members as a result of high strain rates. Therefore, an elevated ground vibration (PPV) or particle velocity is permissible when blasting takes place near concrete structures.

Jan 1, 2014

By Jim Baumann

Deposited millions of years ago in irregular paleokarstic channels, Jamaica’s extensive bauxite deposits provide good quality ore for alumina production and subsequent aluminum smelting. Bauxite mining operations are critical to the Jamaican economy. It accounts for a large percentage of Jamaica’s export earnings. Bauxite production in Jamaica accounts for about 10% of the world’s output each year. Bauxite deposits in Jamaica lie close to the surface. They can be extracted using standard surface mining techniques. The deposits occur in scattered pockets across the country’s rugged landscape. So it was necessary for two of the country’s major mining and refining operations to implement cost effective methods for the acquisition and management of bauxite reserves and surface ownership distribution rights.

Jan 1, 2002

By G. Deschênes

Following a successful investigation on the Central Zone sample, a cyanidation study was conducted on an ore sample from the AD-MW Zone of Clarence Stream Property, owned by Freewest Resources Canada, to develop a leaching strategy to extract gold. At a grade of 6.48 g/t, gold is present in the forms of aurostibite, free gold and electrum. The ore contains 4.3% berthierite/gudmundite, 1.3% pyrrhotite, 0.7% pyrite, 0.07% stibnite and 0.9% arsenopyrite. Similar to the Central Zone, the extraction of gold from the AD-MW Zone can be performed at atmospheric pressure, pH 10.5 and with a low concentration of cyanide. The grind size had no effect on gold extraction between a P80 of 28 to 71 µm. The oxygen and cyanide requirement significantly increased with a ?ner grind. Consequently, a very close control of cyanide addition is required to minimize passivation of gold. Lead nitrate, added in the pretreatment, increased the extraction of gold by 2.3%. Leaching at pH < 10 improved gold extraction but increased the cyanide consumption by 5%. Passivation of gold occurred when the pretreatment was longer than 2 hours. A longer pretreatment reduced the cyanide consumption by 5%. Mineralogical characterization of the leach residue with no gravity pretreatment prior to leaching indicated the presence of unleached gold grains and passivated gold grains. Removal of coarse gold by gravity increased the extraction by 2.8% (leach residue at 0.74 g/t Au). Increasing the DO to 16 ppm or the lead nitrate from 500 to 1,000 g/t increased the overall gold extraction to 90.4% (leach residue at 0.62 g/t), which is the maximum gold extraction obtained. The leaching parameters were 800 ppm NaCN, DO 16 ppm and pH 10.5 for a duration of 120 hours. The associated cyanide consumption was 4.0 kg/t. Gold leaching was not sensitive to cyanide concentration. Reducing the cyanide concentration to 250 ppm resulted in a gold extraction of 89.5% with a cyanide consumption of 2.6 kg/t.

Jan 1, 2009

By Rajni Patel, John McDonald, Steve Dubnewych, Michael McKenna

The Upper Reach segment of the Northeast Interceptor Sewer (NEIS) is a3.2-km-long tunnel excavated in interbedded marine sedimentary deposits with approximately 40 m of cover. The tunnel was initially classified by Cal/OSHA as “potentially gassy.” During excavation, high levels of hydrogen sulfide and methane were encountered, prompting Cal/OSHA to reclassify the tunnel as “gassy.” In addition, the tunnel excavation encountered an abandoned, 100-year-old water tunnel known as the “Narrows Gallery.” This existing tunnel was completely full of water and under 30 m of hydrostatic head. This paper will discuss the unanticipated difficulties and design solutions implemented to construct a gassy tunnel exposed to high volumes of water.

Jan 1, 2005

By J. Torma-Krajewski, C. Hipes

Many mining companies apply ergonomic principles, but it is done either informally and/or reactively. Examples of an informal approach include replacing worn equipment, such as seats, with models that have ergonomic features, or modifying tasks to eliminate safety hazards that will also reduce risk factor exposures that may result in musculoskeletal disorders (MSDs). A reactive approach is followed when modifying a task/equipment after an MSD occurs. Neither one of these approaches involves a systematic method of proactively applying ergonomic principles to actually prevent injuries or illnesses. This paper will discuss how Vulcan Materials Company applied ergonomic principles and the interventions implemented to reduce risk factor exposures.

Jan 1, 2007

China has made great progress in thick coal seam mining, commonly characterized by longwall top-coal caving mining and single-pass longwall mining with a large cutting height. At present, the maximum mining thickness of longwall top-coal caving reaches 20 m while that of single-pass longwall mining approaches 8.8 m. The top-coal caving–related technologies have significantly improved the mining efficiency of thick coal seams and have also made a great contribution to the centralized underground mining of coal. Thus, the number of underground coal mines is greatly reduced in China. However, due to the increase of the mining height and the changes in mining operations, the overburden movement caused by the mining of thick coal seams is more intense, and the influence scope is larger, which brings a series of new problems on ground control of longwall faces. In order to enhance ground control and improve the mining efficiency of thick coal seams

Jul 28, 2020

By Christopher Haycocks

Because of growing pressure from government and consumers to produce more coal, the mining industry must improve existing techniques and devise more efficient mining methods. Mining of the thicker, shallower and geologically superior coal seams in the western United States is being subjected to increasing pressure from environmentalists; and so in order to meet the demand, the coal industry is exhausting the more accessible surface seams and beginning to mine seam of over 1,000 feet in depth and less than. 30 inches in thickness. The longwall mining system is the natural choice for extracting deep and thin coal seams, as it operates almost independently of the overburden rock stress. Due to the added fact that longwall mining is an inherently more productive method than room and pillar mining, many coal producers are looking to it as a means of increasing productivity without a corresponding cost increase. The consistent rise in application of longwall mining in the United States in the last decade illustrates the excellent potential of this technique for the future. American mining conditions are geologically different from those in Europe where longwall mining has been highly developed and extremely successful. Although numerous successes have been recorded in the U.S. with this mining system, a substantial number of failures have also occurred. These failures are due primarily to roof control problems usually over the face, in the tail entry, or both. Another problem area for American operators contemplating the use of this method has been correct selection of equipment, which should be custom fitted to local mining conditions for optimum productivity. It is essential that correct estimates for chock resistances, support densities, supported and unsupported roof spans, as well as rates of advance and length of working faces be provided to optimize mining conditions. Unless extensive pilot projects are planned engineers must choose their equipment correctly at the outset. A typical investment in longwall equipment will amount to several millions of dollars.

Jan 1, 1979