Search Documents

By Peter van Dijk, Gary Almeraris, Philip Rice

This paper describes the Contractor’s value engineering design and the construction of the Interstate I-90 highway tunnel sections under the South Station railroad yard in Boston, MA for the Central Artery/Tunnel Project, using tunnel jacking and ground freezing techniques. Three tunnel box sections were constructed and installed, with typical cross-sectional dimensions of 11.6 m x 23.8 m, and respective lengths of 50.9 m, 78.7 m and 115.6 m. A 12-compartment concrete shield was built as part of the front of each multi-sectional tunnel box structure. The jacking systems employed consisted of rear and intermediate jacking stations and up to 87 individual jacks, providing a maximum total thrust capacity of 42,300 t. The tunnel alignments pass through a geologic profile consisting of historic fill, which contains remnants of old waterfront structures, building foundations and a forest of 19th century vintage timber piles, underlain by organic sediments and marine clay. Ground cover over the tunnels is in the range of 1.8–7.6 m. The groundwater table is at depths of 1.5–3 m below surface grade. The paper discusses the techniques developed and equipment used to successfully build and install these tunnel box structures with minimal impact on the commuter and long distance railroad operations directly above the tunnel alignments. Figure 1 shows the track area at the I-90 EB and WB tunnels.

Jan 1, 2001

By Arthur M. Langer

Since the promulgation of the first Federal Asbestos Standard by the Occupational Safety and Health Administration in 1972, other federal agencies have modified the standard to better carry on their own unique missions. The instruments used to identify and measure asbestos, the sampling protocol, and the criteria used to define asbestos, have been modified to some degree. The Mine Safety and Health Administration regulates and controls asbestos dust in the mining and mineral commodity industries. However, crushed stone and processed ores contain mineral fragments that are frequently difficult to distinguish from asbestos. Mineral nomenclature, instruments for particle analysis, and sampling strategy must be accommodated to some degree to make asbestos control workable and meaningful. Precedent in other agencies has made consideration of these changes possible. Newly identified amphibole asbestos minerals have further complicated the agency?s regulatory charge. Changes in its Asbestos Standard are now being considered. Crushed taconite ore in the Eastern Mesabi highlights many of these issues. ©2008 Published by Elsevier Inc. Keywords: Amosite; Grunerite asbestos; Crocidolite; Riebeckite asbestos; Tremolite asbestos; Actinolite asbestos; Winchite asbestos; Richterite asbestos; Arfvedsonite asbestos; Fluor-edenite asbestos; Asbestos defects; Cleavage fragment; Mineral habit; Mesabi amphiboles

Jan 1, 2008

By S. K. Singh

To meet increasing demand of coal, underground mining is largely being replaced by the exploitation at deeper horizons and with greater complexities. The exploitation-proposition may be below not-to-be-disturbed surface properties or below water-bodies, posing a constant threat of inundation. Also, the mounting pressures to limit the adverse impacts on the environment bring the extraction-undertaking to face more challenges. An understanding of subsidence-mechanism and a rational quantification of subsidence parameters is a requisite herein. This paper presents such pragmatic quantification, validated at mine-sites in India. In comparison, better productivity, conservation and safety is ensured in this approach.

Jan 1, 1999

By Bill Cain, R. John Caulfield, D. Scott Kieffer

The East Bay Municipal Utility District is undertaking seismic upgrades of the Claremont Tunnel in the San Francisco Bay area. The tunnel carries treated water across the active Hayward Fault to supply a major metropolitan area. Studies indicate the tunnel could be severed by fault offset during a major seismic event. A design approach to achieve limited operation of the tunnel following fault displacement has been established and design details are currently being evaluated. This paper describes the project, the design approach, and summarizes significant construction constraints.

Jan 1, 2001

By S. G. Mougiakakou

A computerized system (SCAPEVIEWER) based on landscape indices and artificial intelligence techniques is proposed in order to classify landscape images into various categories according to the quality of the pictured scenery. Photographs (totally 108) from various landscapes have been clustered, from seven experts in accordance to the mean estimation of landscape quality, into distinctive (C1), typical or common (C2), and indistinctive (C3). For each of the landscape photographs, ten (10) environmental and operational indices have been selected and determined, corresponding to visibility (V), naturalness (N), relief (R), flora quantity (FC), flora quality (F), water (W), skyline (SL), visual entities (G), season (S), and viewer position (P). These landscape indices are fed to a classifier. The classifier is a feed forward Neural Network (NN) trained by a novel hybrid method combining genetic algorithms and the back-propagation algorithm with adaptive learning rate and momentum. A total classification rate of 93.5% has been achieved, using only 8 input neurons. The discarded input neurons correspond to the indices S, and P. The pilot system SCAPEVIEVER has shown the feasibility of landscape photograph classification into three categories (C1, C2, and C3) according to the landscape quality, selecting simultaneously the most robust indices, by means of a computerized system combining the knowledge of an expert with a NN based classifier.

Jan 1, 2003

By T. Mills, M. Evatz

Newmont’s Lone Tree Mine, located in northern Nevada, is an open pit gold operation supported by a standard truck and shovel mine production fleet (Caterpillar 785Bs and Hitachi EXs). Newmont continues to search for ways to decrease capital expenditure and lower operating cost, hence the implementation of the Ultra Light Body (ULW) concept. The fundamental idea associated with the ULWs is the increased payload potential. Economic justification comes from successful achievement of additional payload, within the truck’s rated GVW, without changing its loading and hauling characteristics. The increase in payload capacity allows equivalent tonnage movement using fewer trucks.

Jan 1, 2001

Recent advances in GPS, machine guidance technology and telemetry allow an unprecedented level of control of surface mining operations. GPS technology can now locate the bucket of a shovel or the blade of a dozer within 50mm (2 inches).Some of the outcomes possible are: precise selective mining – even when the ore is visually indistinguishable from waste: tracking grade and tonnage of every ore parcel through the mine: real time productivity monitoring: detailed post accident safety analysis: tracking the movements of every piece of equipment. This paper will consider the contribution that GPS based machine control systems can make to ensuring that surface mining projects deliver the outcomes promised in the feasibility studies. Case studies of installations are presented.

Jan 1, 2004

By F. W. DeVries, O. B. Mathre

Addition of Kastone® peroxygen compound and formaldehyde to cyanide gold extraction process effluents, containing at least 5 mg soluble copper per liter, will oxidize acid-dissociable cyanide to levels less than 0.2 mg per liter, without appreciable oxidation of thiocyanate. Most of the copper precipitates and is removed by filtration of the treated solutions. The treatment can be completed in less than 2 hours when the excess of hydrogen peroxide over the cyanide is about 75-100 mg per liter. The excess hydrogen peroxide destroys residual formaldehyde and then is catalytically decomposed by the copper-containing solids that separate, so it will not interfere with subsequent operation. A pilot plant using this technology has been operated for more than four months at rates from 1-2 gpm. Clear, filtered effluent containing less than 0.2 mg acid-dissociable cyanide per liter has been produced.

Jan 1, 1981

Magnetic separation is an age-old technique for mineral beneficiation operations. The existing mathematical models for magnetic separators are quite complicated, and it is very difficult to measure the theoretical separation efficiency. The connectionist approach of modeling, to establish the relationships of the inputs and outputs, is preferred for this kind of problem. Experiments were carried out on a high-intensity roll magnetic separator to develop a database using four input variables (magnetic flux intensity, particle size, splitter position and roll speed) and two output variables (weight recovery and Fe recovery). The artificial neural network (ANN) and statistical methods (MLRG) were used to model the magnetic separation process. For the ANN, the regression coefficient (R2) values between the predicted and measured results were 0.89 and 0.94 for Fe recovery and weight recovery, respectively. Compared to ANN, the multivariable linear regression analysis showed inferior performance in predicting the weight recovery and the Fe recovery. The ANN models for the roll magnetic separator can predict the separation efficiency up to an acceptable limit. These models can be used to modify the operational parameters at mineral beneficiation plants to minimize the effects of variations in the raw material characteristics.

Jan 1, 2009

By Farrukh M. Mazhar, Philippe P. Martin

Electrical Vertical Sounding (EVS) profiling has proven to be a valuable tool to set the alignment and guide the design of a 17 km-long, 4.7m diameter water-conveyance tunnel in the Peruvian Andes at an altitude of 4,260 m. EVS profiling helped determine where to locate boreholes, and reduce the amount of drilling to 1,200 m of vertical and inclined boreholes. EVS profiling allowed the designer to identify and verify by drilling the existence of zones with difficult tunneling conditions that were avoided by realigning the tunnel. The rock quality was checked by drilling and a combined scheme of excavation by TBM and conventional drill and blast technique was developed for the final design.

Jan 1, 2003

By D. R. Spears

As part of its mission to develop technology to assure a continuing supply of minerals, the US Bureau of Mines has investigated the flocculation of a Stillwater, MT, chromite ore. The ore was flocculated at different solids contents and at different stirring speeds to determine the importance and effect of hydrodynamic factors. In acidic and basic pH, the chromite ore was flocculated with high molecular weight polyacrylamides differing in the degree of hydrolysis. Polyacrylamides were found to bind to chromite ore particles through hydrogen bonding. The anionicity of the polymer and the pH affected the degree of polymer-particle interaction, which in turn affected polymer conformation at the surface. A polymer conformation with many loops and tails was used to explain high flocculation efficiency. It was found that such a conformation could compensate for poor hydrodynamic conditions.

Jan 1, 1992

By Y. Q. Zhang, Y. Luo, S. S. Peng, C. T. Holland

Barrier pillars in underground coal mines could eventually be subjected to a hydraulic pressure head due to the build-up of mine water in the old workings. The pressure head could not only act as a force to destabilize the pillar but also cause seepage flow through the pillar and its surrounding strata. Excessive seepage flow could induce piping failure that in turn could accelerate the mechanical failure process of the barrier pillars. In this paper, finite element simulation approach has been employed in the evaluation of the barrier pillars. Both the stress distribution and the seepage flow pattern in and around a barrier pillar have been simulated numerically. The effects of ground stress on rock permeability to water seepage has been taken into consideration in these simulations.

Jan 1, 2001

By C. J. Bise, D. A. Poukhovski

Two integral components of the 30 CFR 48 training requirements mandated for new miners, newly employed experienced miners, and the annual refresher training of all miners are hazard recognition and prevention of accidents. In these categories, instruction shall include the recognition and avoidance of hazards present in the mine, and a review of accidents and their causes. Unlike instruction preparation for fact-based material, program development for hazard recognition places a particular challenge before safety-training specialists because they are often limited in their ability to adequately gauge the trainees' levels awareness prior to training. Further, they must also assure that the training is relevant, and it is presented in a thought-provoking manner. Computer-based instruction is particularly well suited for assisting trainers in developing hazard- recognition topics because it can be used in pre-training and post-training modes for assessment of training effectiveness, in addition to use as a presentation tool. Therefore, this paper will present a recent approach developed at Penn State to apply this technology for assessment and instruction of accident prevention through hazard recognition, with an application prepared for surface coal mines.

Feb 24, 1997

By H. Sarvamangala

Biomineralization of manganese on titanium condenser material exposed to seawater has been illustrated. Biom-ineralization occurs when the fouling components, namely, the microbes, are able to oxidize minerals present in water and deposit them as insoluble oxides on biofilm surfaces. Extensive biofilm characterization studies showed that an alarmingly large number of bacteria in these biofilms are capable of oxidizing manganese and are, thereby, capable of causing biomineralization on the condenser material exposed to seawater. This paper addresses studies on understanding the exact role of the microbes in bringing about oxidation of manganese. The kinetics of manganese oxidation by marine Gram-positive manganese oxidizing bacterium Bacillus spp. that was isolated from the titanium surface was studied in detail. Manganese oxidation in the presence of Bacil-lus cells, by cell free extract (CFE) and heat-treated cell free extract was also studied. The study confirmed that bacteria mediate manganese oxidation and lead to the formation of biogenic oxides of MnO2, eventually leading to biomineralization on titanium surface exposed to seawater.

Jan 1, 2008

By Vladimir G. Kochnev

Crushing and grinding account for the major portion (60 to 80 percent) of the overall expenses for ore processing. Autogenous (AG) and semiautogenous grinding (SAG) have been considered a step forward in comparison to conventional grinding circuits with several stages of crushing and using ball (and/or rod) grinding mills (Bassarear, 1982, MacPherson, 1989, Pithois, Casalis, 1983, Maripuu et al., 1983). However, there remains room for improvement to existing AG and SAG technologies and both technologies have immense economic benefit potential. Experience gained by the Technics & Technologies of Disintegration Ltd. (TTD) in the research of grinding processes shows that grinding in AG and SAG mills can be performed in a more effective way. The company's approach comprises the following elements: ? Novel mill design. ? New liners and lifters. ? Novel discharge grid design. ? Technique of treating material of critical particle size. Comparative tests that demonstrated the usefulness of these innovations are described in this article. Currently, there are hundreds of AG and SAG mills in operation throughout the world. Application of new internal elements of the mills and reconsideration of the circuit design of the existing grinding equipment using present technological solutions would significantly increase the throughput rate and diminish power requirement.

Jan 1, 2008

By Bruce W. Woolpert

During the SME Board of Directors’ midyear meeting in Monterey, CA Aug. 25, I discussed trends in the construction aggregates industry. Many construction-material suppliers may not have yet fully internalized the changes that are taking place. But the changes are significant. And they have shifted the focus in the aggregates industry from “assets” to “people and innovation.” Construction-material suppliers serve many customers. A typical quarrying operation at Graniterock would have more than 1,000 customers, mostly civil engineering contractors. Along with the push toward people and innovation, there is increased emphasis on vertical integration from aggregates to ready-mix concrete and hot mix asphalt, to final construction. If a company is not vertically integrated, it will at least have strong partnerships with other firms, to deliver a high-quality finished project on time.

Jan 1, 2002

By William R. Yernberg

A conference on coalbed and coal mine methane was held March 27 and 28, 2000, in Denver, CO. The conference, organized by the Strategic Resource Institute, was attended by leaders in the coal mining and gas energy industry. The conference focused on the recovery of methane from coal beds as an energy resource and the removal and utilization of coal-mine methane (CMM) related to underground coal mining. The two-day conference discussed methane resources around the world, methods of recovery, methane markets, underground coal mining, health and safety issues and environmental issues related to methane. The consensus among the presenters is that the future looks promising for coal bed methane (CBM) and CMM.

Jan 1, 2000

By Joachim Klein, Frank Reimann

Nodular-graphite cast iron (GGG) is a material similar to steel, and one which exhibits excellent properties, in particular for components exposed to pressure. GGG cast iron has been used in many cases when sinking mine shafts with conventional tubbing. With linings made of cast iron tubbings (the backfill concrete is not integrated into the calculations, and merely serves as bedding) the properties of the cast iron can be made full use of, provided the tubbing is made to the appropriate cross-section. Calculations have shown that better static values can be arrived at when using cross-sections other than those of tubbings made to conventional German standard. The cross-sectional design of the new types of shaft lining made from GGG is to be developed on these lines irrespective of the cast iron structure being only stressed component or its restistance function being combined with the one of concrete. GGG 50 is used for the first time to make the reinforcing inner liner of a main shaft currently sunk in Germany. The physical properties of nodular-graphite cast iron, strength and deformability, suggest that, in the future, its application will not be restricted to shaft support but also in tunneling. New moulding techniques with better three-dimensional modelling resulted in new tubbing designs as installed e.g. for the Hannover underground at present. Shield-driven tunnels have to withstand earth and water pressure, apart from axial machine loads. In this field time is money as well. Therefore easy handling and quick installation are necessary for successful, use. Last but not least, safety is of first-order importance for work in shaft sinking and tunneling. Cast iron lining systems, accordingly, are adequate systems, in particular for excavations underneath water for transport systems and for goods and passengers.

Jan 1, 1987

Equipment-washing facilities at Freeport-McMo-Ran?s Sierrita Mine in Arizona produce a mixture of oil and water that was difficult to dispose of easily or cheaply. However, after some changes in the facility, waste oil is now used as part of the mining process. Freeport-McMoRan Copper & Gold Inc., head-quartered in Phoenix, AZ, operates copper, gold and molybdenum mines. It is the world?s largest producer of molybdenum. Heavy equipment used at the mine is hosed off periodically in the wash bay. The dirty water and oil mixture drains into the sump next to the bay. Oil was manually collected for disposal. This was a tedious and dirty process Mine managers sought a more efficient method of removing the oil. Instead of spending the time and effort skimming the tank with vacuums or sorbents, they enlisted the help of Abanaki Corp., manufacturer of the Model 4 Oil Grabber. Engineers designed the sump to utilize prevailing winds to blow the oil to one corner. This was the ideal place for the Abanaki skimmer. The skimmer removes the oil and discharges it into a plastic storage container. ?This reduces the time needed to keep the area clean, and the staff can focus on cleaning the equipment rather than worrying about the oil,? according to Jay Salerno, construction manager at the Sierrita Mine. Salerno is considering adding an optional oil concentrator to the skimmer to make the process even more efficient. The concentrator would remove any water picked up by the belt and return it to the sump, leaving nearly pure oil for disposal. Because the mine is located in the Sonoran desert, most of the water evaporates in the hot, dry air and is not reused.

Jan 1, 2009

By J. Wright

Since the 1960’s toroidal conductivity has been used to determine the Alumina to Caustic ratio of the digester discharge liquor stream. In recent years the application of ceramic materials have allowed the sensors to moved upstream to provide tighter control of the process. In the Bayer process, dissolving the aluminum contained in bauxite ore in caustic soda and converting it to aluminum oxide produces alumina. An important parameter of the process is measuring the alumina to caustic ratio in the digester discharge stream. The A/C ratio at a given caustic concentration is a measure of the degree of saturation of the alumina in the plant liquor. The aim in the process is to achieve a high A/C ratio. There is however a limit where precipitation will occur if the A/C ratio is too high. For many years conductivity has been used to determine the A/C ratio. Conductivity of discharge liquor is related to the caustic concentration. The change in the caustic concentration is in the same direction of the change of solubility of the alumina. Controlling the conductivity through adding additional bauxite ore and varying the dilution flow can increase plant yield.

Jan 1, 2001