Search Documents

By P. van der Veen

There are two key reasons for this presentation: - Sustainability - Improving the economic, environmental and social impact of mining. As I will discuss in my presentation we see sustainability throughout the mine life cycle as critical for successful mine development - that is the mine makes a successful contribution to economic development and poverty alleviation for the host community and host country and at the same time the mine is a successful investment for the investor. - Knowledge Sharing ? The World Bank is not only a development bank, but also a ?knowledge bank?. One of our key functions is the dissemination of usable information and knowledge. We are here not only to share our experience but to learn from your experience as well ? two reasons that fit clearly with the mandate of the World Bank Group.

Jan 1, 2003

By W. J. Schlitt, K. McNaughton

A heap-leach field test was conducted during the 1993-1994 winter season at Carmacks, Yukon Territory, Canada. The purpose of the test was to demonstrate the viability of heap leaching Carmacks oxide copper ore in an arctic setting on a year-round basis. The test itself utilized a 5-m-diam crib loaded with 250 t of composite ore from the Carmacks copper deposit. The ore was stacked to a total height of 7 m in the crib, including 1 m of ore as an over- layer above the emitter system. This matched the plan for the commercial heap at the time when the test was started. The design also replicated an interior segment of the commercial heap. Leaching was done at a flow rate of 0.2 L/min/m2 using leachate at 21 °C. This temperature was maintained with no external heat input other than normal process heat transferred from electrowinning to the leachate via solvent extraction. Winter conditions were quite typical of those expected at the mine site. The temperature reached -54°C, while averaging -13°C over a three-month period. In spite of some flow system problems, leaching continued unabated, and freezing was limited to the insulating ore over-layer and isolated points near the outer crib walls. Thus, the test demonstrated that year-round heap leaching of Carmacks copper ore is practical in an arctic setting.

Jan 1, 2000

By A. Moharana

A massive slide at Bingham Canyon wiped out a side of the pit and covered the main haul road in and out of the pit. All pre-slide mine designs and schedules were no longer valid. New designs and schedules needed to be developed quickly to provide management with information regarding the immediate post-slide production potential and the time needed to ramp back up to full production. At the time of the slide, an effort was already underway to convert Bingham?s in-house Medium Term Scheduling Process to MineSight®?s Schedule Optimizer (MSSO). One of the main reasons for doing this was to reduce the time needed to produce Medium Term Schedules at Bingham, which involves a complex shovel-based scheduling approach with shovel productivities based on shovel type and the types of mining cuts to which the shovel is assigned over each planning period. The objective of the schedule was to maximize shovel usage, satisfy mill feed requirements of four SAG mills with variable milling rates, and have flexibility in setting truck constraints. This paper will describe how the new MSSO-based mine scheduling process met the challenge of producing new schedules for Bingham in a minimal amount of time.

Feb 23, 2014

By William N. Poundstone

Since World War II, when off-track mining became popular, mining machinery has undergone much change. However, the change has been basically to make the machines more powerful, more productive and more reliable. Little change has been made, in this period, in the basic mining system. While steady improvement was made in productivity until the passage of the new Federal Coal Mine Health & Safety Act, I believe that the cost Co benefit ratio of further improvement from this basic approach of improving the existing extractive tool is not as promising as I believe may be obtained from a new approach. Consequently, six years ago Conoco and Consol undertook a comprehensive long-range R&D program to see if improvements of a more basic nature could be made in underground mining. We concluded early in our program that while many things currently limit the rate of production such as the rate at which roof can be supported, time needed to advance ventilation systems, time required to clean up and rock dust, time required to maintain and service equipment as well as time lost due to haulage deficiencies, that the key to improvement was a truly flexible continuous high capacity haulage. With face equipment in use today, mining rates can be increased with such a haulage system where the ability to support the roof exceeds the ability of conventional haulage equipment to remove the coal. More importantly, if we could develop such a system, it would set the stage for development of far more sophisticated methods of mining at the face than exist today, and as new and more dependable mining machines and methods are developed, continuous transportation will enable the gains envisaged in production to be realized.

Jan 1, 1974

By Xinming Chen, Huazhe Jiao, Qi Zhang, Yunfei Wang, Liuhua Yang

The effect of initial damage generated by weakly cemented interlayer surfaces on the physico-mechanical properties of layered cemented tailings backfill (LCTB) is considered for the interlayer inclination structure generated by multiple layered backfills in large-scale mining voids. Utilizing the theory of damage mechanics, the damage evolution and constitutive model of LCTB with interlayer inclination is constructed by considering the coupling of interlayer inclination effect and loading. Based on Mitchell’s mechanical model, we analyze the damage mechanism of the inclined cementation surface of LCTB, and derive the expression for the strength of LCTB considering interlayer inclination. The mechanical properties test of LCTB with different inclinations was carried out, and the results showed that the damage model of LCTB established was highly consistent with the experimental curves, which verified the correctness of the model. The initial inclination damage leads to the decrease of adhesive cohesion of cemented surface, and with the increase of inclination, the separation of layered surface, aggravation of misalignment, layered cemented surface is more prone to shear damage, and the mechanical properties of cemented tailings backfill in the lower part of layered surface are not effectively played, which reduces the overall performance of the material.

Nov 23, 2023

By Terry I. Mudder

Metal complexed cyanides in wastewaters form as a result of interactions of free cyanide with metals present in the wastewater and exhibit varying degrees of stability, toxicity, and treatability. Thiocyanate, a pollutant commonly found in cyanide bearing wastewaters, is formed through the interaction of free cyanide with sulfur containing species (i. e. pyrrhotite) both present in the wastewater. In certain industrial processes, such as the beneficiation of gold and silver, cyanide is an essential reagent. Since free cyanide, complexed cyanides, and thiocyanate are potentially toxic to humans and aquatic organisms, these compounds must be removed from wastewaters prior to their discharge into surface or ground waters serving as potential potable water sources, marine or fresh water habitats

Jan 1, 1984

By D. C. Rotherham

The Kidston gold discoveries were originally made about 1907, and by 1934, 1.76 Mg (62,000 oz) of gold had been produced from placer and lode mining of higher grade, most¬ly oxidized gold ore. As mining in the lode ore penetrated deeper, costs increased and the world gold price stagnated. The lode or underground production averaged close to 6.9 g/t (0.2 oz per ton) Au for the 201 kt mined. No mining or development took place from 1934 until 1965. Kidston's high grade ores were exhausted by 1934. From 1965 to 1976, exploration had developed 3 Mt of about 3 g/t (0.88 oz per ton) Au. Placer Pacific acquired rights to the property in 1976 and began a geologic and engineering study of the district. It was clear that the deposit had the potential for becom¬ing a large-tonnage, low-grade producer. However, explora¬tion had to discover the tonnage and grade and engineering needed to solve the obstacles of production costs. Bulk material handling problems were addressed by Placer's wide experience in open pit mining, and the increase in work index accompanying deeper ores was handled by Placer's metallurgists. The matter of power for the operation was solved by engineering studies. These showed that power could be generated and brought in economically. The price of gold also increased after 1976, and this helped in the economic analysis. The Kidston discovery since 1976 is really a combination of good exploration geology and careful engineering plan¬ning that overcame the obstacles presented by ore characteris¬tics and the location of the deposit. The attached paper by Harry Mustard is an extract of his honors thesis and explains the deposit geology.

Jan 1, 1990

By Mamookho Elizabeth Makhatha, Mbal Henock‑Michel Mwanat, Kubangala Brest Kasongo, Ntumba Edward Malenga

This study investigated the operating parameters that affect the kinetic dissolution of copper and cobalt from sulfidic ores. The sulfuric acid concentration, temperature, sodium chloride concentration, particle size range, and leaching time were selected to deduce the kinetic mechanism of the leaching reaction. Other parameters, such as a stirring speed of 250 rpm and the percentage solid 10% w/v, remained constant. The results reveal that an increase in acid concentration enhances the leaching rate of copper and cobalt. Copper and cobalt dissolution was positively affected by the addition of sodium chloride. The highest leaching rates of copper and cobalt were 24.71% and 15.65%, respectively. The chemical control and diffusion control by shrinking core models are well fitted as the kinetic models representing the dissolution of the minerals. The respective activation energies for copper and cobalt dissolution of 10.92 and 31.023 kJ mol− 1 for the chemical control and 18.83 and 37.28 kJ mol− 1 for diffusion reaction control were established from temperature-based experiments.

Aug 26, 2022

By S. A. Saki, J. F. Brune

"INTRODUCTION Longwall coal mining leaves large areas where the coal has been made removed and the roof rock strata collapse, forming a zone of broken rock rubble called the gob. Figure 1 shows a typical longwall gob area along with the gate roads. The ventilation pattern for progressively sealed longwall panels follows a simple “U” pattern where fresh air is coursed inby to the headgate, flows along the face and exhausts through the outby tailgate as shown in figure 1(a). An important variation of this pattern is the back return (BR) arrangement where the exhaust air from the face is drawn inby and around the nearest open cross cut before it turns in the outby direction towards the exhaust fan. Figure 1(b) illustrates the use of back return. This arrangement moves the point of low pressure from the tailgate corner up to 60 m inby and thus maintains fresh air in the tailgate region that could otherwise be contaminated with gob air.The gob area may contain remnants of unmined coal or parts of overlying coal beds that continue to release methane, eventually filling the gob area with methane in concentrations far above the explosive range of about 4.5 to 15%. Many gob areas must be equipped with gob ventilation boreholes (GVBs) to extract methane, and GVBs often exhaust methane at concentrations from 50% to 90% (Saki, 2016). Due to oxidation processes occurring in the gob, the oxygen content is reduced to a low level, with nitrogen and CO2 making up the major remaining components of the gob atmosphere. FORMATION OF EXPLOSIVE GAS ZONES IN GOBS Since the longwall face area is ventilated with fresh air below 1% methane and the face and gob areas are not separated, an explosive fringe will form where the methane content lies within the explosive range and oxygen content remains above 12%. Figure 2 shows a typical development of such an EGZ. This figure is based on a computational fluid dynamics (CFD) model developed by CSM researchers to analyze gas concentrations and flow patterns in longwall mining. Figure 2(a) shows the formation of EGZ in the gob with a U type ventilation scheme, where EGZ lies right behind the shields in the tailgate corner. Figure 2(b) shows the formation of EGZ in the gob combining U type ventilation scheme with BR, where EGZ is pushed away from the face deep into the gob. The CFD modeling parameters and boundary conditions have been verified with field data from two cooperating, active longwall mines (see Worrall 2012, Marts 2015, Gilmore 2015 and Saki 2016). Other mine geometries, methane inflow rates and gob permeability distributions can be modeled to establish representative gob atmospheric conditions. Two GVBs were operating in the model, extracting 0.165 m3/sec each. The methane in the working areas and returns was kept below 1%. Methane flowing into the model from a rider coal bed above the mined seam was at the rate of 0.55 m3/sec."

Jan 1, 2017

By D. S. Choi, H. D. Dahl, D. L. McCain

The paper examines current room and pillar mining practice in the U.S.A. from the standpoint of rock mechanics. Consideration is given to the deformation characteristics of the roof formation and the coal seam as determined in the laboratory as well as in the field. The results can be utilized by the practicing mining engineer to improve current mine design practice.

Jan 1, 1982

By W. B. Greer, J. J. K. Daemen

Introduction The performance of seals in boreholes, shafts and tunnels is an important concern in mine safety, in the control of effluents from operating and abandoned mines and in the underground containment of hazardous wastes (Einarson and Abel, 1990; Mining Waste Study, 1988). Despite the clear need for effective seals, few documented test results are available concerning the performance of in situ seals. Some evidence indicates that horizontal or near-horizontal holes are especially difficult to seal properly (Kelsall et al., 1982). This research involved the installation, extensive hydraulic testing, removal and post-test examination of a 10-cm-long x 10-cm-diam cement grout seal in a near-horizontal borehole in limestone. The work was performed in an underground mine on Marble Peak in the Santa Catalina Mountains, AZ. A test hole was diamond cored in the recrystallized limestone of the Escabrosa formation. The hole is 33.24 m long, 10 cm in diam, and dips at 10.4°. The hole extends between two drifts and thus is accessible from both ends. Seal installation Surveys to assist in selecting the interval to seal consisted of core logging, video logging and constant-head injection tests using a straddle-packer unit. The location selected, 3 m from the lower end of the hole, had low hydraulic conductivity (3 x 10-10 to 3 x 10-9 cm/sec) and was free of significant fractures. The grout used, an expansive Class A cement, was provided by Dowell-Schlumberger, Tulsa, OK. A grout mass about 1.5 m in length was installed, with a dump bailer, above a temporary mechanical plug. Groundwater in the hole, if any, was minimal during placement. After 13 days of curing, the grout mass was partially drilled out from both ends, leaving a seal 10 cm long. Water distribution in rock mass The distribution of water and fluid pressure in the rock mass near the seal appears to be complex. The generally dry condition of the borehole and rock mass suggests that the rock mass near the seal was unsaturated prior to the injection tests of this research. The injection tests presumably created an expanding saturated zone around the seal. However, anomalously high fluid pressures, consistently recorded by one of two piezometers installed near the seal, suggest connection to a source of significant natural hydraulic head. Comparable head variations for closely spaced piezometers have been reported by others (Sowers, 1976). [ ] Seal testing The seal was tested for 3.5 years, using steady constant-head, tracer travel-time, dye-injection, head-buildup and transient constant-head tests. These tests are fully described in Greer and Daemen, 1991. In the head-buildup test, transient flow occurs through the seal (and rock mass) to a closed, water-filled interval of the borehole adjacent to the seal. The test consists of monitoring the rise in head in the closed interval until steady conditions are approached. The test may be analyzed in terms of a one dimensional analytical model to obtain the effective hydraulic conductivity (Ks) and specific storage (Sss) of the seal. Analysis in terms of an axisymmetric three-dimensional numerical model may yield properties of both the seal and rock mass.

Jan 1, 1993

By P. L. Stavenger

Principles of Operation and Mechanical Features General Mechanical Description Sieve-bend screens are high-capacity screening devices which utilize stationary, concave, wedge-bar screening surfaces. A complete sieve bend is comprised of a feed distribution chamber, a structure for holding the screen surface, and collection chambers or chutes for oversize and undersize materials. In devices used for metallurgical practice, provision is usually made for reversal of the direction of flow over the surface, either by rotating the surface or by changing the feed nozzle position. The size of the unit varies in height from 5 to 8 ft, and in width from 2 to 8 ft. The orientation of the wedge-bar surface is such that the slots between the wedge bars are perpendicular to the flow of feed material over the surface. The feed distribution means is arranged such that the flow of liquid suspension is distributed evenly and tangentially over the width of the screen surface. A variety of means are used including simple gravity weir feeds, long slotted nozzles, and a multiplicity of round nozzles. A typical gravity-fed weir type nozzle is shown in Fig. 18. Most sieve bends are fed with gravity feed in such

Jan 1, 1985

By Russell Frith

The entire subject area of micro-seismic events due to stored strain energy, as distinct from gas-driven coal outbursts, can be readily sub-divided into firstly events with their energy source from within the coal seam (termed “bursts”) and secondly, event with their energy source outside of the coal seam in either the overburden and/or floor strata. The reason for sub-dividing micro-seismic events in this manner is that if the causation mechanisms and associated geotechnical conditions are materially different, then effective pre-mining predictions and subsequent operational controls may also differ. Attempting to explain a multitude of micro-seismic event types without consideration of varying source mechanisms will inevitably lead to inadequate causal explanations and effective controls.

By Bern Klein, Richard W. Lawrence, Scott Frostad

A laboratory study was conducted to evaluate the effects of various kinetic test protocols on sulfate production, NP depletion and time to acidity. Six test protocols were evaluated including standard humidity cells, non-aerated cells, tall cells, shaken cells, simulated precipitation cells, and NP depletion columns. The study indicates that test protocols which disrupt the oxidizing environment, such as extreme wetting and drying cycles, shaking the cells, or the high addition of acidic water will create an unnatural environment that affect the results. Trickle leach and non-aerated test protocols create an oxidizing environment that more closely represents field conditions and are therefore recommended.

Jan 1, 2000

By Douglas B. Silver

Study Parameters (Status as of February 1993) Time Period: 1989 -1991 151 North American Public Metal Mining Companies Fiscal not calendar year basis 85+% of Canadian and U.S. Metal Production Au, Ag, Cu, Pb, Zn, Mo, Ni, W Results are Preliminary and Research Continues Chicken Little is Alive and Well

Jan 1, 1993

By R. Miller

Lowering our globe’s emissions is a major effort as we move toward a future net-zero carbon environment requiring significant investment in a new, low-carbon infrastructure, along with key market incentives to change. Industry will play a key part in this transformation, requiring expertise in both energy and emissions. Key elements of the de-carbonization strategy are: energy data, emissions reporting method, governance, de-carbonization project generation and drivers, the MACC, electrification, and the de-carbonization checklist. For a zero carbon future, it will be key for business leaders to understand decarbonization, anticipate technological changes, and implement new business me

Mar 2, 2022

This study was conducted to evaluate the effects of a diesel particulate filter (DPF) regeneration process on the concentrations and size distributions of aerosols in an underground mine. Two active regeneration strategies were examined for an electrically regenerated sintered metal fiber filtration system, and the effects were compared with those observed for a muffler and the same system operated in a passive configuration. The effects were assessed for three steady-state engine operating conditions. The number and mass concentrations and size distributions of aerosols in mine air were found to be strongly affected by the exhaust configuration, engine operating conditions and the regeneration process. When the system was operated in active configurations, the concentrations exhibited a transient and cyclic nature. At light load conditions, the distributions of aerosols in mine air were dominated by accumulation mode aerosols for all exhaust configurations and regeneration strategies. High concentrations of nucleation aerosols were observed when the DPF system was used and the engine was operated at high load conditions. A positive correlation between accumulation of particulate matter in the filter and the efficiency of the filter in removing accumulation mode aerosols was observed for all conditions. In the case of high engine load, reductions in accumulation mode aerosol concentrations were linked to a substantial increase in number concentrations of nucleation mode aerosol. Overall, the filtration system was found to be very effective in reducing total aerosol mass and elemental carbon concentrations for all engine operating conditions. However, the system was substantially more effective in passive than in active regeneration configurations.

Jan 1, 2012

By SUHAINA ISMAIL, NORLIA BAHARUN, SHAIK ABDUL RAHMAN, WAN NUR SYAFIQAH ANUAR, MOHAMMAD REZAEI ARDANI

Hypochlorite leaching system is a strong oxidizing solution for metal sulfides, which are naturally associated with gold extraction. This study evaluated the hypochlorite leaching of refractory gold ore by using the response surface method–central composite design (RSM-CCD) as a statistical approach in determining the optimum condition of gold extraction from refractory gold ore. The studied parameters for the gold recovery were pH (4 to 6), concentrations of Ca(OCl)2 (0.5 to 1.5 M) and NaCl (2.5 to 3.5 M) in the solution. It was found that the maximum gold extraction of 82.46% (13.85 g/t) was achieved at a pH of 4.0 with NaCl and Ca(OCl)2 concentrations of 2.93 M and 1.08 M, respectively. The statistical analysis also revealed that the amount of gold recovery in chloride solution was significantly depended on pH as the main factor, followed by concentrations of Ca(OCl)2 and NaCl.

Jan 8, 2021

By L. Alan Weakly

The U.S. Department of Energy (DOE) has entered into a $l.5 million Cooperative Agreement with Alpine Equipment Corporation/Astro International Corporation ("Alpine") of State College, Pennsylvania, for the evaluation of water-jet-assisted (WJA) mechanical cutting of oil shale under actual mining conditions. A commercial-sized, heavy WJA mechanical miner is being assembled based upon the successful "factory testing" of a smaller prototype miner utilizing standard tungsten-carbide and Polycrystalline Diamond Composite (POC) bits in large oil shale boulders. Actual field testing of the machine will be conducted in an oil shale mine located in the Piceance Basin of Western Colorado. In-mine logistical support is being provided by several oil shale companies through the Colorado Mining Association (CMA) and the U.S. Bureau of Mines (USBM).

Jan 1, 1990

By R. Gray, B. Hebblewhite

Experience from Australia had identified what is referred to as nonconventional surface subsidence behavior. This occurs under irregular surface topography, resulting in valley closure, valley floor uplift or “upsidence,” and far-field horizontal movements, occurring even beyond conventional “angle of draw” limits. This paper discusses such behavior recently observed in Pennsylvania and focuses on the 2005 case of Duke Lake Dam in Ryerson Station State Park. In July 2005, there was a significant increase in water leakage through a number of growing cracks in the dam, leading to the dam being breached to avoid an uncontrolled failure. An underground longwall mine was located approximately 900 ft to the north, mining at depths of 330 to 720 ft. Investigations, including a subsequent ground movement monitoring program, found a range of evidence in the vicinity suggesting that valley closure and farfield horizontal movements may have occurred, resulting from the adjacent mining. Besides discussing the phenomenon of nonconventional subsidence behavior and the Ryerson State Park case study, this paper includes an assessment of the mining, geology and subsidence impacts and suggested ground behavioral mechanisms.

Jan 1, 2015