Search Documents

By Atta Ur Rehman, Kwame Awuah‑Offei

This paper evaluates the effectiveness of similitude theory in predicting the draft of a rubber tire loader’s bucket during initial penetration. The work uses 1:16 and 1:8 scale models of an 18-t capacity load haul dump, scaled with the Buckingham Pi Theorem, to evaluate the prediction of draft and penetration under different operating and different dynamic conditions. The authors hypothesize that the observed relationships between draft and longitudinal penetration and the operating and dynamic conditions will hold true for an upscaled model. Similarly, the authors hypothesized that the results of experiments conducted with the smaller scaled model should predict the draft on an upscaled model. The results show that the relationships between draft and longitudinal penetration and operating and dynamic parameters are similar for both scaled models. Similarly, the draft on the upscaled model, predicted by using the experimental results of the small model, is similar to the measured draft on the upscaled model. The mean difference between the two is 1.71 N with 95% confidence interval of [-3.51, 6.93], which is very good given the average draft is approximately 330 N. Thus, the work indicates that both hypotheses are true for draft. However, the work shows that scaling muck pile particle sizes using the Buckingham Pi Theorem is not adequate to ensure good predictions of penetration. This work provides insights that will help design engineers to acquire useful data on scaled models and use it for various analyses on heavy machinery.

Oct 6, 2021

By C. E. Golson

Modern concrete technology emphasizes the basic qualities required of an acceptable aggregate: it must be clean, sound, homogeneous, and of a size gradation resulting in a concrete of the desired physical qualities at a minimum cost. In the case of coarse aggregates, crushing, scrubbing, and screening will usually provide the required material, although beneficiation is often necessary in order to eliminate unsound or deleterious fractions. Beneficiation is also applicable to fine aggregates,( but the processes most often employed are washing, classification, and dewatering.

Jan 1, 1959

By J. Noll, C. DeGennaro, C. Zhou, J. Srednicki

"The personal dust monitor (PDM) (model PDM3700), as well as other electronic devices, can cause electromagnetic interference (EMI) which can disrupt the operation of some proximity detection systems (PDSs). A 15 cm (6 inch) minimum separation distance between the miner-wearable component (MWC) of the PDS and the electronic device usually avoids these disruptions, but due to the amount of equipment on a miner’s belt and the method of wearing the PDM in some situations, this distance can be difficult to always reliably maintain. Another method of reducing EMI effects is utilizing magnetic field shielding. The shielding capability of several different materials was investigated by surrounding the PDM with the material and quantifying the EMI. A copper mesh pouch reduced the EMI from a PDM3700, allowing a minimum separation distance of 10 cm (4 inches) instead of 15 cm (6 inches) as shown in a previous study for an unshielded PDM. A MU-metal box had a better shielding effectiveness, as it further reduced the minimum separation distance to less than 7 cm (2.8 inches). Shielding reduced the EMI of the PDM with MU-metal providing better results than the copper mesh. These materials may be beneficial for shielding individual components of the PDM or for constructing a shielded pouch. However, before the advantages of a shielded pouch can be determined, the effects of just the shielding material (metal) on the PDS needs to be quantified. INTRODUCTION According to statistics from the Mine Safety and Health Administration (MSHA), 43 miners have been fatally struck or pinned by a continuous mining machine (CMM) since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems (PDSs) have been developed and are required on all operating CMMs in underground coal mines, with the exception of full-face CMMs, by 2018 (MSHA, 2015)."

Jan 1, 2018

By Greg Watson, Dennis Ofiara

"TBMs have been used in mining in decades past, but their use has been limited and sporadic, due to both perceived and actual application difficulties. With new technology and mounting success stories, this is changing. For both coal and metals mining, deep ore bodies require long access tunnels, and an efficient and economical method of reaching those deposits. Today, mining engineers are considering TBMs as part of the overall mine development plan. Planned TBM mine drifts are not only longer, but have more complicated trajectories. Mine development TBMs will have to cope with varying geology, potential for high water inflows, steep gradients, and high temperatures. TBM systems are being planned to cope with such difficulties. TBM systems will be considered and increasingly deployed for mine development, even if commodity prices remain low. TBMs can satisfy the need for increased productivity, better life of mine infrastructure, and safety. Effective conveyor systems are essential to support TBM operation in many mining applications. Many mine development tunnels are slopes, driven down at the steepest practical gradient to reach the deep ore body. Conveyors are often the only safe and effective way to haul the TBM muck form such tunnels. This paper will review the historical use of TBMs in mining, and will discuss the 2015 status of TBMs and conveyor systems in mining, and the special requirements and adaptable features needed in order to make efficient TBMs a reality in mines worldwide.HISTORICAL USE OF TBMS IN MINING APPLICATIONS The first successful hard rock TBM was invented in 1954. Over the next decades, TBMs have been used in many mining applications: Mine access drifts in several Spanish mines •,White Pine Copper Mine, USA •,Selby Coal mine drift, UK •,Coal slopes in Appalachia, USA •,German coal mines accdess drifts, several mines •,Magma Copper San Manuel, USA •,Cape Bretton Undersea Coal Slopes, Canada •,Stillwater Mines, USA"

Jan 1, 2016

By Evgueni Jak

Pyrometallurgy is an important sector of modern industrial society actively participating in solving current environmental, economic, materials scarcity and other challenges. Recent advances in analytical methods, experimental techniques, thermodynamic, phase equilibria and process modelling tools provide new opportunities to increase the productivity of pyrometallurgical reactors, the treatment of complex feeds and metal recoveries. Fundamental theoretical models can now be used to make a significant next step towards the development and implementation of computerised models describing real industrial processes—Virtual Reactors, and computer-aided smart-decision-making systems that may be called Pyro-GPS by analogy to GPS; these developments can facilitate knowledge-based improvement and optimization strategies. The implementation of these improvements require ongoing collaboration between researchers, industry and government

By C. R. McClung

"Molybdenum, in the form of molybdenite, is a common byproduct of many copper mining and concentrating operations. Contrary to most copper sulfide minerals where recovery is principally liberation controlled, the recovery of molybdenite is much more complex with fully liberated particles commonly lost to tailings. It is this complexity that facilitated the necessity for a geometallurgical investigation of molybdenite from the Bingham Canyon deposit. The aim of this investigation was to determine the effect mineralogy and/or mineralogical attributes (i.e. morphology, angularity, liberation, size) have on the recovery of molybdenite in the processing circuit. A set of samples was collected from the ores and products produced by Rio Tinto Kennecott’s Copperton Concentrator. All samples were analyzed using normal polarized reflective light, Mineral Liberation Analyzer (MLA) and X-ray diffractometery (XRD) techniques. The results of this investigation revealed the presence of two distinctly different types of molybdenite, which have been identified as the two polytypes of molybdenite, i.e. hexagonal (2H) and rhombohedral (3R). The 2H polytype occurs as textbook-shaped particles in quartz-molybdenite veins that are located in the core of the Bingham Canyon deposit. The 3R polytype occurs as disseminated, “ball”-shaped particles with a dull or frosted appearance along the margins of the mineralized intrusive body or central core. Concerning their metallurgical behavior each type exhibits unique metallurgical properties that are consistent with those reported in the published literature. For instance, the 2H polytype is easily ground and kinetically “faster” floating with surface attributes that are amenable to higher rates of recovery. This commonly results in the production of a high quality molybdenum concentrate under normal operating conditions common to most copper concentration operations. In contrast, the 3R polytype is difficult to grind and kinetically “slower” floating with surface attributes that less amenable to recovery under normal operating conditions. Therefore, in deposits with higher concentrations of the 3R polytype, modifications to the normal operating parameters may be necessary to improve the recovery of molybdenum. Finally, a preliminary investigation into the metal budget of porphyry Cu and Mo deposits indicates that a positive correlation may exist between the total economic metal budget and the polytype content. For example, higher concentrations of the 3R polytype appear to be more prevalent in Au-enriched porphyries versus Mo-enriched porphyries. This observation may also serve to help explain why it is easier to obtain high rates of recovery in Mo ± W-rich deposits, which contain little to none of the 3R-polytype. Consequently, the potential for the metal budget of a porphyry deposit to be used as an indication of the molybdenite polytype present, as well as its impact on the economics (exploration) and/or on the processing circuit (plant design) could exist. In conclusion, this investigation highlights the necessity of understanding the mineralogical properties or characteristics of molybdenite and/or other economic mineral(s), as these can and will have a direct impact upon the performance and plant optimization."

Jan 1, 2016

By Joseph Moses Botbol

The disposition of world mineral resources is such that a vital need exists for both the most efficient development of existing resources and the rapid disclosure of as-yet undiscovered resources. The technological developments described in this report are directed primarily toward the acceleration and increased efficiency of mineral-resource exploration program. In the past decade the use of computers in the mineral industry has grown exponentially. Most computer applications in mineral exploration are designed to be implemented either before or after data collection. Few, if any, computer applications are designed to be used during the collection of data. One major reason for the lack of development of computer applications in this area is that comunications links do not exist between computing systems and the remote areas that host mineral-deposit exploration programs.

Jan 1, 1975

By PEILIN LAN, LEONARD HILL, SIMON TIMBILLAH, BERNARD FOSU, CESAR SOSA-BLANCO

The use of sodium hydrosulfide (NaHS) in most of the operations in by-product molybdenum flotation comes with safety concerns and, in some instances, a high reagent cost. Engineered solutions at the various operations where NaHS is used have reduced the possibility ofH2S gas evolution immensely. However, the threat of exposure remains, and this, coupled with the high dosages of NaHS consumed, supports the continued search for alternative depressants. This paper focuses on efforts to study the applicability of disodium carboxymethyl trithiocarbonate (DCMT), an organic depressant, as an alternative to NaHS. Benchscale rougher flotation results for samples from the Sierrita Cu–Mo plant showed the best DCMTperformance at 8 kg/t of DCMT and pH=10.5 with 30 min of shear conditioning and 10 min of flotation conditioning time. The Aminpro plant model simulation confirmed that DCMT with 4–8 kg/t under certain shearing and conditioning times achieved superior or equivalent Mo–Cu separation efficiencies when compared to NaHS.

Apr 19, 2021

By Winthrop F. Watts, Robert W. Waytulonis

During the 1980's. the Mine Safety and Health Administration (MSHA) proposed new regulations for the use of diesel equipment in underground coal mines, and the National Institute for Occupational Safety and Health (NIOSH) recommended that whole diesel exhaust be regarded as "a potential occupational carcinogen", and that reductions in exposure to exhaust pollutants would reduce excess risk. During the same time, the Bureau of Mines tested new emission control technology to minimize diesel emissions. The objectives of this paper are to discuss the major issues regarding diesel exhaust emissions. especially diesel particulate matter (DPM) , and to highlight emission controls that will be available. DPM is a potential health threat because it is respirable in size and is composed of nonvolatile carbon with adsorbed or condensed compounds. These compounds include potentially mutagenic or carcinogenic hydrocarbons such as polynuclear aromatic hydrocarbons and sulfates. DPM contributes to the degradation of air quality in mines with typical mean concentrations ranging from 0.2 to 1.0 mg/m3. In addition to adequate ventilation, control of DPM can be achieved by implemention of improved work practices, regularly scheduled engine maintenance, and emission controls.

Jan 1, 1991

By Ronald L. Wiegel

In a mineral processing plant there are a number of routine decisions which are based at least in part on the plant's metallurgical performance. Among these are those related to: 1) equipment functioning properly 2) suitable operating conditions 3) reagents achieving desired results 4} determining operating response to changes in ore 5) defining circuits offering potential for improvement A step beyond the routine, are the periodic management evaluations of operating supervision and technical assistance, which are based largely on profit -a direct function of are availability, metallurgical performance and operating costs. The "yardstick", excuse me -"meterstick", by which performance is best measured is the plant metallurgical balance, which tells not only what was produced but how it was produced. Since this metallurgical balance is directly related to both plant profits and individual rewards, it is only reasonable to make that "meterstick" as precise as humanly possible.

Jan 1, 1978

By J. F. Childs

"INTRODUCTION Comprehensive overviews of the world-class talc deposits and related prospects in Montana were published by Olson (1976) and by Berg (1979). Both of these compilations include detailed descriptions and maps of the talc deposits and occurrences and were followed by a regional map and summary descriptions of the talc deposits published by Van Gosen et al. (1998). More recent publications, descriptions and field guides for some of the deposits include Underwood et al. (2014), Cerino et al. (2007), and Cerino (2002). The present paper focuses on some of the more recent ideas regarding talc formation that have developed since the publication of the earlier overviews. Olson (1976) reported that talc production from the deposits in southwestern Montana was over 200,000 tons in 1974 and that talc production had doubled between 1969 and 1974. The last year for which the U.S. Geological Survey published production records for talc by state was 1993. Production in Montana in 1993 was 350,000 tonnes (Virta, 1994). Remaining reserves are substantial at all three of the producing mines in the district. Minerals Technologies Inc., the parent company of Barretts Minerals Inc., stated in its 2014 annual report that it has reserves of 2,791,000 tons of talc. Imerys stated in its financial report for 2014 that it had 19,638,000 tons of proven and probable talc reserves at its North American mines. Although the Imerys reserves were not reported by individual mines or states, a large proportion of the total reserves would likely consist of the reserves at the Yellowstone mine, located south of Ennis, Montana. Talc mined in southwestern Montana is of high purity and is the quality used in a wide variety of applications including paints, ceramics, plastics, rubber, coatings, agriculture, cosmetics, and pharmaceuticals. GEOLOGIC SYNOPSES FOR MAJOR MINES AND COMMENTS ON REGIONAL DISTRIBUTION OF TALC OCCURRENCES The general geology of southwestern Montana is shown in Figure 1along with the locations of the three producing talc deposits in the area and the extent of pre-Belt marbles that host all of the talc mines and prospects. The term “pre-Belt” is used in the present paper because zircon and other radiometric data developed in recent years indicates that the metamorphic rocks that form the crystalline basement for the middle Proterozoic Belt basin in the Dillon Tectonic Block of southwestern Montana includes both Archean and Paleoproterozoic rocks (O’Neill et al., 1996; Foster et al., 2006; McDonald et al., 2012). An envelope or “corridor” has been superimposed on the geology in Figure 1 which encompasses all of the talc deposits that have a significant resource. This “talc corridor” will be discussed in later sections of this report. The more important talc deposits are discussed in this report section."

Jan 1, 2016

By Lynn Huntsman

INTRODUCTION The Sunnyside mines of Kaiser Steel Corp. are lo¬cated on the west flank of the Book Cliff Range, a tongue of the Wasatch mountain range in Utah. The mines are 193.12 air km (120 air miles) southeast of Salt Lake City and 40.23 km (25 miles) east of the town of Price. The area has a semiarid climate with an an¬nual rainfall of 304.8 to 381 mm (12 to 15 in.) and a temperature range of -23.3 to 32.2°C (-10 to 90°F). The base of the Book Cliff Range is approximately 1981 m (6500 ft) in elevation with some mountain peaks in excess of 3048 m (10,000 ft) (Fig. 1). The Sunnyside mines were opened in the late 1890s and have been operated continuously since that time. Kaiser Steel leased the No. 2 mine in 1942 and pur¬chased the entire property in 1950. There are three mines adjacent to one another, each with its separate access, ventilation, and haulage. The three mines en¬compass an area extending 12.87 km (8 miles) along the outcrop and dipping northeasterly 2.41 to 3.22 km (11/z to 2 miles) into the Book Cliffs. During 1975, only the No. I and No. 3 mines were operating to sup¬ply 908 184.7 t/a (1,000,000+ stpy) of clean coal to the Kaiser Steel mill at Fontana, CA. Sunnyside coal is blended with coal from the Kaiser Steel mine near Raton, NM, and with purchased coal from noncompany sources to form the mix for the coke ovens. At that time, Sunnyside operated three longwall units and five to seven continuous miner units. Typical production for that time came from one miner unit pillaring an area not conducive to longwall mining; one or two miner units on construction or modernization projects, and the remaining units used to develop future longwall panels. Longwall mining has been a part of the Sunnyside scene since 1961 when the first panel was set up in the lower Sunnyside seam of the No. 3 mine. Through 1975, 27 longwall panels were mined (Fig. 2). Of the more than 47 173 604 t (52,000,000 st) of clean coal that were taken from the property through 1975, 6 350 292.9 t (7,000,000 st) were mined by longwall methods. Coal was brought to the surface in 4.5-t (5-st) mine cars and crushed to -152.4 mm (-6 in.) before entering the preparation plant. Coarse coal is cleaned by Baum jigs and fine coal (-28 mesh) is cleaned in flotation cells. The coal is reduced to 50.8 x 0 mm (2 x 0 in.) and belted to an aboveground storage pile with a ca¬pacity of approximately 113 398.1 t (125,000 st). The coal is gravity fed through two 1.52-m (5-ft) diam culverts directly into railroad cars, which pass beneath the storage pile through an arched excavation. Eighty-four 90.7-t (100-st) cars make up a unit train which makes the round trip to the steel mill in four days. Additional trains are scheduled in as demands dictate. Loading rates in excess of 13 607.8 t/h (15,000 stph) have been attained. Geology The coal seams of this area are of Cretaceous age and are classed as a medium volatile bituminous coal. coal, with a sulfur content less than 1 % and 6 to (20-mile) zone of the Book Cliffs, and this area is owned or under lease by either Kaiser Steel or US Steel. Coal in adjacent areas is noncoking but an excellent steam coal, with a sulfur content of less than 1 % and 6 to 7% ash. Sunnyside coal contains 40% volatile, 53% carbon, less than 1 % sulfur, and 51/2 to 61/2 % ash after washing. There are two minable seams throughout most of the Sunnyside property known locally as the upper and lower Sunnyside. Separation between the seams varies from less than 300 mm (1 ft) near the southern boundary adjacent to the US Steel Columbia mine, to over 12.19 m (40 ft) in areas of the No. 3 mine in the center of the Sunnyside property. The upper seam varies in height from 1.2 to 1.98 m (4 to 61/2 ft) while the lower seam varies in height from 1.52 to 4.28 m (5 to 14 ft) in areas of No. I mine where the two seams apparently come together. The majority of early work was con¬centrated in the upper seam which has a stronger roof and a lower sulfur content. When Kaiser Steel began mining the No. 3 mine in the early 1950s, it mined in the lower seam beneath the old workings with conven¬tional and continuous mining equipment. Numerous bounces and pressure points created by unextracted pillars and barriers in the upper seam made this a low¬production, high-cost mine and brought about the ad¬vent of the first longwall system. The first unit, while small by today's standards, successfully mined panels that had been all but given up and saved the mine from closure. There were areas that could not even be mined by longwall because of the erratic extraction in the upper seam. The system was successful enough to allow operations to gain access to and develop virgin areas of the upper seam. Development of longwall mining in the No. 3 mine has been confined to the upper seam since late 1964. With the almost complete extraction afforded by the longwall system, it is felt the lower seam can be successfully worked in future years (Fig. 3). In most of No. 1 mine, only the lower seam (or lower seam and upper seam combined) is minable, except in the northwest portion where a rock split has again separated the seam into two 1.83 to 2.13-m (6 to 7-ft) thick beds. In this area, the upper seam or upper split is being mined. The separation between seams at the present workings in this area varies from 0.609 to 6.1 m (2 to 20 ft). It is hoped that most of the lower split can be mined using shield supports and/or what¬ever new technology is developed in the coming years. The coal seams in this area dip to the northeast at an average grade of 10%. The dip near the outcrop reaches 22% and gradually decreases downdip. Over¬burden ranges from a few meters at the outcrop to 762 m (2500 ft) over some of the deeper workings. In the next several years, some overburden will be in excess of 914 m (3000 ft) as the lower mine workings extend ever deeper under the Book Cliffs. To cope with the

Jan 1, 1982

By Z. H. Xie, D. S. He, W. M. Xie

China has rich phosphate rock resources, but with their continuous depletion, the rich ore resources have become increasingly scarce, which makes the exploration of collophane more important. Medium- and low-grade phosphate rock cannot be utilized until their impurities have been removed through mineral processing. However, due to the similar physical and chemical properties of dolomite and phosphorus minerals, the separation of dolomite from phosphate

By Jon Pocock, Ashma Singh

The traditional approach for the beneficiation of South African siliceous sedimentary phosphate ores has been reverse cationic flotation. The robustness of this approach, however, has been a concern due to its sensitivity to parameters such as slimes content, headgrade ( P2O5 and SiO2 content), reagent dosages and conditioning times. The phosphate mineralisation for the ore body under investigation is predominantly carbonate fluorapatite composed of mainly quartz and apatite and minor amounts of chlorite, ilmenite and carbonates. Beneficiation of low grade sedimentary ores containing calcareous impurities, such as calcite and/or dolomite in addition to siliceous gangue, is required to meet the increasing demand; therefore, much research has been carried out to find an alternative technique to beneficiate this material. This paper investigates traditional flotation approaches versus the currently adopted ‘Crago Process’. Comparative results are presented in terms of upgrade potential for the production of concentrate rock for downstream applications. The novelty of the ‘Crago Process’ lies in its double stage approach, i.e. direct fatty acid flotation followed by reverse cationic amine flotation. The Crago process was able to achieve higher upgrades reporting at 32.1% P2O5 compared to conventional cationic flotation only achieving grades of 18.5% P2O5. Furthermore, the recovery gain was 3%.

May 13, 2023

By K. V. Godfrey

With the increasing need to exercise better control over mill circuits has come a requirement to develop rapid, accurate means of measuring circuit parameters. One of the most important parameters is the assay of the material in the circuit (or about to be introduced to the circuit). To date, most on-stream analysis has been performed using X-ray fluorescence equipment. Neutron activation offers an alternative method in certain circumstances, and one which has several interesting advantages. Recognizing the need for a simple, safe neutron activation unit suitable for on-stream analysis in the mineral industries, Atomic Energy of Canada Limited has designed, built and tested the SHERLOCK system. One prototype (SHERLOCK I) is located in Ottawa and is now used primarily in research. A second prototype (SHERLOCK III) is located in Vancouver at the laboratories of B.C. Research. This unit is being used for some development research and for evaluating the unit in specific applications. Most of the work completed to date has been aimed at proving the technique and in developing some of the parameters needed to design systems for a milling plant. Funding for the work has been through research grants and through sponsor¬ship by interested companies.

Jan 1, 1971

By L. Valentik

Many attempts have been made during the last forty years to evaluate the performance of gravity separation equipment, that is, the effectiveness with which light and heavy particles are separated. The most comprehensive treatment of the subject was made at the 1st International Conference on Coal Preparation held in Paris (1950) by Cerchar. The methods suggested by the Conference were accepted and very widely used in the last 25 years. This paper discusses an improved method of evaluation in the light of the now accepted standard presentation. The float and sink analysis of the product is presented on a Gaussian distribution curve, resulting in an easier visualization of the inherent difficulties of separation. The ogives of the distribution curve are then plotted, giving a quantitative measure of the deviation from perfect separation as an error distance instead of an error area. Illustrations of the new method are given both for gravel and for coal preparation, but the concept is valid and applicable to other types of minerals which are separated by gravity methods.

Jan 1, 1968

By I. Iwasaki

Differential flotation of bulk sulfide concentrates from Duluth gabbro into copper and nickel concentrates could be implemented by first destroying the hydrophobic coating with ozone and then by recovering the copper concentrate with a copper-selective collector. A number of parameters involved in the use of ozone; such as the sequence and the conditioning time of ozone treatment, the pulp pH, and the level of xanthate addition, were investigated.

Jan 1, 1985

By R. J. Matetic, J. Noll, C. Zhou, J. DuCarme, M. Reyes, J. Srednicki

"In April 2016, the U.S. Mine Safety and Health Administration (MSHA) began requiring the use of continuous personal dust monitors to monitor and measure respirable mine dust exposures to underground coal miners. Mines are currently using the PDM3700 personal dust monitor to comply with this regulation. After the PDM3700’s implementation, mine operators discovered that it interfered with proximity detection systems, thus exposing miners to potential striking and pinning hazards from continuous mining machines. Besides the PDM3700, other electronic devices were also previously reported to interfere with proximity detection systems. MSHA sought the aid of the U.S. National Institute for Occupational Safety and Health (NIOSH) and mining industry stakeholders to determine how the PDM3700 and some other electronic devices and proximity detection systems interact with each other. Accordingly, NIOSH investigated existing standards, developed test protocols, designed experiments and conducted laboratory evaluations. Some interferences were observed to be caused by electromagnetic interference from some electronic devices, including the PDM3700. Results showed that there was no significant interference when the PDM3700, as well as other electronic devices, and the miner-wearable component of the proximity detection system were separated by distances of 15 cm (6 in.) or greater. In the present study, it was found that the PDM3700 and the personal alarm device needed to be at least 15 cm (6 in.) apart in order for them to be used simultaneously and reduce potential interference. IntroductionUnderground coal miners are exposed on a daily basis to a variety of hazards, such as coal dust exposures, high noise levels, roof and rib falls, potential for fires and explosions, and operating and working with heavy machinery. One of the hazardous jobs is that of operating or working near a continuous mining machine. According to U.S. Mine Safety and Health Administration (MSHA) statistics, 44 miners had been fatally struck or pinned by a continuous mining machine since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems have been developed and are required on all operating continuous mining machines in underground coal mines, with the exception of full-face continuous mining machines, by 2018 (MSHA, 2015a)."

Jan 5, 2018

By J. Kretschmann, H. Mischo, O. Drusche, S. Krause

Mining is and will be inevitable in spite of the increasing implementation of circular strategies. The energy transition and population growth will boost the demand for critical raw materials. It is the opportunity for miners to reinvent their business models. Generating attractive new business cases with sustainability-oriented innovations meets investor and stakeholder expectations from the beginning. This contribution guides managers on their pathway towards sustainable success. Contextual sustainable business model patterns will be presented that can be adjusted individually, regardless of actor’s size. It will also point out, how sustainable value creation can be measured on business model level.

Feb 1, 2023

By S. S. Klima, H. Jiang, T. W. Beck, Y. Zheng

Researchers at NIOSH’s Pittsburgh Mining Research Division (PMRD) performed comparative testing of six different water sprays at pressures ranging from 689 kPa (100 psi) to 6,895 kPa (1,000 psi) in a 14.5-m3 (512-ft3) confined dust chamber. Testing was conducted to determine the effect of various pressures on each spray’s respirable coal dust knockdown ability. It is known that higher water pressures are typically preferred for lowering airborne dust concentrations, but it was important to determine at what pressure range the dust knockdown ability of each spray plateaus or reaches its minimum dust concentration. Results from this testing showed that several sprays saw up to 100% decrease in dust concentrations during the five-minute water spray testing period, with some occurring well below the maximum 6,895 kPa (1,000 psi) spray pressure.

Feb 1, 2023