Search Documents

By S. Hodgson

Introduction The Red Dog zinc/lead deposit in northwest Alaska is the second largest zinc deposit ever discovered. Being developed by Cominco Alaska, with startup scheduled for early 1990, it will ultimately be the largest zinc mine in the Western World. Table 1 shows the reserves of the deposit. Bob Baker, a local bush pilot, discovered Red Dog in 1968. The US Geological Survey assessed the find. But the Red Dog site had been withdrawn from staking by provisions in the Alaska Native Claims Settlement Act of 1971 (ANCSA). Under the terms of ANCSA, the deposit was selected by the NANA Regional Corporation, one of 13 native corporations established by the Act. Then, in 1980, the US Congress confirmed this selection, in the Alaska National Interest Lands Conservation Act. In 1982, Cominco and NANA reached an agreement that has led to the development of the mine. Under the agreement, Cominco leases the property from NANA, develops and operates the mine, and markets the concentrate produced. In return, NANA receives royalties and, after capital recovery, participates in the net proceeds from the operation. The Alaska State Government is also playing a role in the development of the mine. Under the auspices of the Alaska Industrial Development Authority (AIDA), the state will construct, own, and operate the DeLong Mountains Regional Transportation System. This consists of a 84-km (52¬mile) road from the minesite to the Chukchi Sea. Located here are the port facilities necessary to store and ship the annual concentrate production and receive the mine fuel and supplies. For using this transportation system, Cominco will pay an annual toll fee. Over the anticipated 50 year life of the operation, the fee will provide a 6.5% return to the State of Alaska. In late 1986, Cominco's Board of Directors approved the Red Dog project. And, during the summer of 1987, road construction began. In February 1988, initial stripping began at the ore body and construction started at the millsite. Project setting The project site is approximately 1000 km (600 miles) northwest of Anchorage, 84 km (52 miles) east of tidewater on the Chukchi Sea, and 192 km (120 miles) north of the Arctic Circle (Fig. 1). The countryside consists of low, rolling hills that lead into mountains north and east of the deposit. The vegetation is typical tundra mat. And the site is in an area of permafrost. However, the permafrost is relatively warm and some areas have been found to be thawed. Examples would be creek bottoms and the site of the main waste dump.

Jan 12, 1988

By Hongwei Wang, PEIPEI CAO, Yongping Wu, JIANQIANG JIAO

In the fully mechanized top caving mining of steeply inclined, extra-thick seams with variable angles, the mechanisms of roof rock movement, failure, caving and filling are highly complex. This is due to the varying angle of coal seam in different areas, which makes rock–equipment stability control challenging. In this paper, the surrounding rock deformation and failure mechanisms, bearing structure of the overburden, and working characteristics of the supports are elucidated. The principle and key technologies of rock–equipment stability control are presented and applied to control the overburden of the regional failure and realize safe and efficient mining of the working face.

By Baojie Zhang

The main goal of this study was not only to investigate the effectiveness of the FGX Dry Separator for removing pure rock from run-of-mine coal producing a better feed stock for conventional coal preparation plants but also to optimize the FGX Dry Separator performance for producing a salable clean coal product without using the conventional wet coal preparation processes. A Model FGX-1 Dry Separator with feed throughput capacity of 10 tph was extensively tested at the Illinois Coal Development Park using two coal samples having distinctly different cleaning characteristics. Statistically designed experimental programs were conducted to indentify critical process variables and optimize FGX Dry Separator performance by systematic adjustments of critical process variable parameters. The coal cleaning performance of the FGX Dry Separator was evaluated for the particle size range of 63.5 x 4.76 mm in most cases, although FGX Dry Separator feed consisted of nominal -63.5 mm run-of-mine coals. The best cleaning performance obtained from the FGX Dry Separator is described by specific gravity of separation (SG50) and probable error (Ep) values of 1.98 and 0.17, respectively. The SG50 and Ep values for individual size fractions were as follow: 1.90 and 0.12 for the +50.8 mm size fraction, 1.95 and 0.18 for the 50.8 x 25.4 mm size fraction, 2.01 and 0.19 for the 25.4 x 12.7 mm size fraction, and 2.03 and 0.23 for the 12.7 x 4.76 mm size fraction. These process efficiency measures produced a clean coal with ash content of 13.38% from a feed coal with ash content of 34.45%. Ash content of tailings and middlings streams were 85.09% and 39.57%, respectively. Total sulfur contents of corresponding streams were 3.87%, 4.68%, 6.87%, and 4.62%. For a relatively easy to clean Illinois No 6 seam coal (Cleaning Index: 0.72), only about 0.42% of the clean coal (i.e., 1.6 float fraction) present in the feed was lost to the tailings stream. For a relatively difficult to clean coal (Cleaning Index: 0.53), about 0.98% of the clean coal present in the feed was lost to the tailings stream.

Jan 1, 2012

By Howard M. Wells

Portfolio theory and the Capital Asset Pricing Model (Modigliani and Pogue, 1974) provides an investment decision rationale which takes account of the benefits of diversification in reducing effective risk, but this theory does not consider the financial capability of the firm to survive large losses if they should occur. The LL-curve theory (Wells, 1976) takes the latter consideration into account, but it does not provide for the effects of diversification. This paper pro- poses a general theory to account for both diversification and the financial capacity of the firm to underwrite the investment risks.

Jan 1, 1983

By C. E. Semler

A 5 year test program, involving on-line, in-vessel exposures at Barrick Goldstrike Mines. Inc. has provided valuable information and experience about the materials and designs for brickwork linings in pressure oxidation autoclaves. A variety of brick and mortar products have been evaluated. Properties before and after exposure are used to document the performance. Benefits have included the development of a new silicate mortar improved understanding of brick requirements and increased autoclave operating time between maintenance shut-downs. More improvements are expected in the future based on further information from the test program.

Jan 1, 1997

By N. Chow

The recovery of manganese from lower-grade resources has been studied for a number of years. Of key importance in prior work was the discovery that higher-valent manganese can be readily leached with sulfurous acid. This eliminates the need for high-temperature reduction roasting that is conventionally used in processing high-grade material. High-temperature roasting is energy intensive, emits a large amount of carbon dioxide and would not be economical for processing lower grade material. While the prior work provides important information for extracting manganese from lower-grade resources, the production of unwanted byproducts and high water and energy usage has limited its commercial use. This paper describes the results from laboratory work that demonstrate solutions to problems that to this point have precluded commercial development. Preliminary mass and energy balances show that a significant opportunity exists in producing manganese with this hydrometallurgical scheme in a low-cost, environmentally friendly manner. The emphasis of the work is on low water use, low overall energy use and economic destruction of unwanted byproducts.

Feb 1, 2012

By Harvey P. Knudsen

This paper illustrates the application of geostatistics to a roll front type uranium deposit located in Wyoming. The steps involved in calculation of experimental variograms, variogram modeling and verification of the resulting models are described in detail. The resulting spherical variogram models for grade thickness and thickness show strong geometrical anisotropies. The major axis of anisotropy for both variables is approximately parallel to the axis of the roll front and the minor axis perpendicular to the roll. This model confirms the technique of drilling "fences" across the roll front, where the drilling is much closer together than the fences along the roll.

Jan 1, 1978

By G. E. Sreedhar, R. Kumar

The pockets of high silica blue dust across the entire high grade hematite deposits in the Bailadila sector bothers the excavation activity due their iron content, which is higher than the threshold value specified by the Indian Bureau of Mines and the agony of stacking them separately due to their fragile & powdery nature. The physical nature of blue dust and its negligible alumina content makes these a potential source of hematite, which is a blessing in disguise. As most of the particles are in the form of an independent grain making it appropriately suitable feed for dry magnetic separation and thus the dry beneficiation has turned a bane into boon by enabling to produce concentrate either suitable for using as DSO or amenable for blending. The emphasis on carrying out dry beneficiation studies in the present context serves the purpose of mineral conservation, mitigates the issues of excavation and stacking as well as conservation of water resource. This paper describes the laboratory and pilot scale dry beneficiation studies carried out on blue dust of 48 – 60%Fe and Silica up to 30% at 25 Kg/hour to 400 Kg/hour, resulting in production of concentrate assaying 60 – 65%Fe. INTRODUCTION High silica blue dust (HSBD) is associated with Banded Hematite Quartzite (BHQ) and is available in abundance in various pockets across the Iron ore body in the Bailadila region of Chhattisgarh state. High Silica Blue dust occurs in the form of free granular particles and also as friable lumps. The chemical quality of this falls under sub-grade category (45 – 55%Fe) and as per the guidelines of Indian Bureau of Mines, these are to be stacked and conserved as future resources of Iron if it can’t be utilized in the present circumstances. Due to its friable nature, stacking of HSBD is a challenge and it is also compounding the problem by polluting the air under high velocity wind conditions. Because of its physical nature and occurrence in pockets pose challenge to systematic mining. The existing processing set up of the operating mines is designed to treat either Direct Shipping ore (DSO) or Run-of-Mine (ROM) have grade >60% Fe. The present practice of beneficiating iron ore fines (<1 mm) comprise combination of two or more processes such as desliming, hydraulic classification, magnetic separation and flotation apart from requirement of grinding depending on liberation characteristics. The HSBD which is predominantly occur as free granular particles, is significantly low in its alumina content. This gives us an opportunity to utilize them by exploring a suitable beneficiation process so that the concentrate produced can be used as a sweetener for alumina rich iron ore/concentrate. Thus, in the present study, an attempt has been made to adopt dry high intensity magnetic separation technique to explore the amenability of the high silica blue dust for beneficiation.

Jan 1, 2019

By U. Schoepf

Economic and at the same time environmentally acceptable mining of small vertical ore bodies and veins to great depths has always been a challenge for miners. The Bauer cutter system, widely used in civil engineering, has been further developed for applications in exploration and mining, to a sustainable system for selective mining with a focus on small vertical ore bodies and veins, as well as residual ore in open pit operations. Current situation of conventional mining of small ore bodies and vertical veins Small ore bodies and vertical or near-vertical ore veins often pose a challenge to the mining industry. The relatively small size of the ore deposit over great depths or lengths, with only limited exposure to the surface makes economical mining difficult. Open pit mining of such ore bodies must either be terminated early because of the high stripping ratio and the enormous environmental impact or is unprofitable from the very beginning. The required massive stripping of waste rock leads to high material hauling times and costs, intensive roadway and bench construction and maintenance, possible safety hazards due to heavy vehicle movement, pit wall stability risks, intensive surface water management and massive waste dump requirements. In addition, it can be assumed that increasingly extensive rehabilitation measures will be required in the future after mine closure. Particularly in vertically oriented magmatic and hydrothermal deposits the technical, economic and environmental limits for further pushbacks, to extend the open pit depth, can lead to an early end of mine life even if a significant quantity of residual ore is left behind. Going underground is only a viable option in a limited number of mines with very high ore values and volumes. The high development cost of an underground mine, as well as the higher underground mining costs, often prevent further mining to greater depths.

Feb 1, 2023

By Mike Amick

As virgin coal reserves dwindle, more and more mines are being opened in areas with previous mining. As addressed in this conference before, there are solutions available for designing mines extracting coal from reserves with known underground workings above or below the target seam. Often times, however, mining begins with limited knowledge of the underground workings. Even with careful planning, the proposed design has limited success because the ?facts? as presented during planning turn out not to be as accurate as one would like. At National Coal?s Mine #14, mining the Walnut Mountain seam, after driving the main entries in some 34 crosscuts, it was found during routine mine examinations that the pillars had separated from the roof in a few areas of the mains. Immediate roof conditions proved to be sound but questions arose concerning the stability of the main roof and floor. Core tests were done to better determine the rock strengths and characteristics. The paper presents the ideology used to tackle the effects of mining over old works in an operating coal mine. This paper discusses the analysis of the symptoms observed and the steps taken to ensure that this pillar separation was caused by the underlying old workings and that the separation was expected and controllable.

Jan 1, 2009

By Francis J. Quinn

The Natural Gas Act, of 1938, which put interstate pipelines under the jurisdiction of the Federal Power Commission, did not place a protective competitive shield around such companies - nor does any provision of the act guarantee them a profit. Natural-gas pipelines are competitive with each other and also with the coal and oil industries. Gas distributing companies must compete not only with the coal and oil industries, but also with the electric industry. Natural gas has captured markets from oil, which had taken them from coal. Oil men contend that gas prices have: been, held to an artifically low level by regulation. The electric industry is moving into the space-heating market, which pleases the coal people because the coal industry&apos;s largest customer since losing the railroads to dieselization has been the electric companies. The coal industry is attempting to monopolize the industrial and electric generating market through government intervention, and this is being done under the guise of concern for the national welfare through advocation of a "National Fuels Policy purporting to, further the cause of fuel conservation. Such a policy is contrary to American principles and would result in the individual&apos;s loss of freedom of choice and ultimately, in less reserves of preferred fuels because of diminished exploration efforts.

Jan 1, 1961

By Kent D. Gastreich

As the number of prime surface coal mining sites diminishes with time and with the potential for increased coal demand, areas that were previously not mined because of their difficult mining conditions, marginal economics, and controversial environmental nature, will have to be considered if surface coal mining is to continue in the future. Such sites include areas near major rivers, streams, and lakes. The name most commonly given to these areas by regulatory agencies is "wetlands". The exact definition(s) to the term "wetland" will be discussed later in this paper. Most coal operators are now more than familiar with permitting requirements under the Surface Mining Control and Reclamation Act of 1977 (SMCRA). The SMCRA permanent regulatory program recognizes the fact that coal mining operations will periodically encounter streams, wetlands, etc. Although discussed in various sections of the permanent program regulations, the relationship of coal mining operations to wetlands is particularly evident in the performance standards regarding hydrologic balance and protection of fish, wildlife and related environmental values.

Jan 1, 1980

By D. T. Jr. Tarr

History of Development The hydrocyclone, probably because of its basic simplicity, has been used for various classification applications since before 1890. A patent was granted in the United States in 1891 to Bretney on a device for separating sand from water, collecting the sand in a closed chamber for intermittent discharge, practically identical to some present-day water desanding cyclones. Between 1900 and 1937 there were 30 or more additional patents issued on liquid cyclone configurations or their use. About 1937 liquid cyclones began to be used commercially in the treatment of cellulose fiber in the pulp and paper industry separating contaminating particles from the fiber in water suspension used for making high grade paper products. Nichols Engineering & Research Corp. of New York was marketing a liquid cyclone for cleaning sand and din particles from fiber suspensions in the pulp and paper industry by 1937. The designs during this period were such that the cyclones discharged a small amount of relatively high density material into a chamber connected to the cyclone apex which in turn discharged the collected dirt material intermittently. By the early 1940s hydrocyclones as we know them today began to appear both in the pulp and paper industry and in coal prorzssing.18 Considerable experimental work was done on small, mostly 3-in.- diam, cyclones operating at relatively high pressure drops, in the range of 50 psi, to remove very small contaminating particles from cellulose fiber in the production of high-grade writing papers in the paper industry.18

Jan 1, 1985

By Jonathan K. Hrica, Brianna M. Eiter

The ability to identify hazards during a workplace examination is a critical skill for mineworkers to have in order to maintain a safe workplace. While research suggests that being able to successfully recognize hazards requires a complex set of competencies, it is unclear which competencies are most critical to adequately perform a workplace examination. This paper presents a hazard recognition competencies framework as an explanation of the competencies that affect mineworker hazard recognition. To better understand how the industry is selecting and preparing workplace examiners, researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) interviewed nine health and safety (H&S) professionals at surface stone, sand and gravel mine sites throughout the United States. These interviews verified that the competencies included in the hazard recognition competencies framework agree with perceptions of the interviewed H&S professionals, who also provided validity for the critical role these competencies play. Finally, the results of this study are presented within the context of current NIOSH research findings related to hazard recognition.

By Tony Szwilski

A correlation between the rank, ash content and coal seam discontinuities and coal strength/stiffness is discussed. Rebound hammers were used to evaluate the strength properties of two coal seams. The coefficient of variability of the rebound tests are compared with those of laboratory compressive strength tests by other investigators.

Jan 1, 1985

By A. Ghosh

Commonly used predictors of ground vibration from blasting, being linear in log-log plot, do not model the underlying physics of wave attenuation. Amplitude of the wave decays with distance due to geometrical spreading and inelastic attenuation producing a nonlinear carve in log-log scale. The nolinear decay of seismic waves has also been observed from non-explosive sources, such as, pile driving, drop hammer, traffic, etc. The improved predictors, by explicitly taking these two mechanisms into consideration, model the data trend extremely well at all distance ranges. Actual field data from different studies have been used to validate the improved models.

Jan 1, 1991

By L. G. Austin

The model originally proposed by Austin, et al., has been modified in the light of further investigation of the breakage laws in SAG milling. The model uses a fully-mixed reactor for short L/D mills and calculates the breakage of small particles by the nipping action of balls and pebbles. The autogenous self-breakage of larger lumps is treated as an effective means of fast breaking rock and much slower breaking rock. Experiments show that fast autogenous breakage can be treated as a first-order breakage with an overall specific breakage rate which incorporates fracture and chipping. Similarly, slow breakage incorporates fracture and abrasion. Autogenous breakage is cushioned by the accumulation of fine material. Simulation results are compared to results from tests in a 2 m diameter continuous pilot-scale SAG mill. Future work is discussed.

Jan 1, 1985

By Steven A. Savage

Agrico Chemical Company, as we presently know it, is the result of the coming together of several different fertilizer operations. The Williams Companies, our parent organization, first entered the fertilizer business in 1971, when it acquired the fertilizer operations of the Gulf Oil Company. This gave us, among other things, the manufacturing facility at Donaldsonville, Louisiana. In 1972, The Williams Companies acquired Agrico Chemical Company from Continental Oil Company, bringing in a manufacturing facility and phosphate mines at Pierce Florida. Our Florida Mines are in the region commonly known as the Bone Valley Region of Florida. The majority of the phosphate fertilizer produced in the United States utilizes rock mined in this region. The Donaldsonville Plant was originally built in 1967-68 on the site of the old Faustina Plantation at an approximate cost of $80,000,000. (This plant is commonly referred to as our Faustina Plant.) Until such time as Agrico was acquired from Continental Oil, the Donaldsonville Facility was solely used to upgrade phosphoric acid into finished granular products.

Jan 1, 1986

By M. J. Virnig, G. A. Kordosky

Throughout time, the mining industry has been very successful in meeting the world&apos;s requirements for metals and materials while meeting the challenges of decreasing ore grades and increased emphasis on protection of the environment. This success has been due to the development and implementation of new technologies. A clear example of such a development over the past 25 years is the increasing use of leaching/solvent extraction/electrowinning for the recovery of copper from oxide and sulfide ores. The key to the successful introduction of this technology was the discovery and development of the hydroxyoxime liquid ion exchange reagents by General Mills Chemicals (now Henkel Corporation). An important role was also played by the close working relationships between General Mills Chemicals and Ranchers Exploration which resulted in startup of the first plant in 1968 and between General Mills Chemicals and Bagdad Copper which resulted in the startup of the second copper SX-EW plant in August of 1970. Following on the heels of the hydroxyoxime development came the commercialization of other new chelating reagents based on different chemical functionalities, i.e., beta-diketones, alkylated 8- hydroxyquinolines and sulfonamidoquinolines. This initial spurt of activity was then followed by a slowing of development in terms of new reagent functionalities. Activity has continued in terms of further optimization/improvement of existing reagent functionalities but the commercialization of new reagent functionalities has slackened. This observation reflects the fact that the development of new reagent functionalities for metal recovery has become increasingly more expensive such that the right combination of price and sales volume must exist in order to justify the investment required to bring a new reagent to the market place. Given the dependence of the mining industry on innovation to meet the needs of the future, one can ask how these new developments, particularly in new reagents, will occur. To arrive at an estimate of the costs involved in commercializing a new metal extractant functionality, particularly a chelating type functionality, a case study of the development of LIX ®* 34

Jan 1, 1994

By Meng Li, Hao Nie, Weitian Ding, Mamdouh Omran, Ying Li, Yao Ge, Yaowei Yu, Abourehab Hammam, Lei Zan

This study examines the isothermal and non-isothermal reduction behaviors of iron ore compacts in a pure hydrogen atmosphere and compares the results obtained during the reduction process by CO. The different phases accompanying the reduction reactions were identified using X-ray diffraction (XRD) and its morphology was microscopically examined. In isothermal experiments, temperature plays a significant role in the reduction process. At any given temperature, the reduction rate during the initial stages is higher than that during the final stages. The reduction rate in H2 atmosphere was faster than in CO gas. The comparison of activation energy values suggested that reduction with H2 is more efficient thanwith CO. At the same temperature, the time required to achieve a certain degree of reduction was lower when using H2 gas than CO atmosphere. In non-isothermal tests, the heating rate has a significant effect on the reduction rate and reduction extent. At the same heating rate, the degree of reduction was higher in H2 atmosphere than in CO gas. Based on experimental data, the parameters of reaction kinetics were deduced by application of model-free and model-fitting methods. The reduction in H2 atmosphere was controlled by nucleation model (Avrami-Erofeev model), while the CO reduction reaction was controlled by gas diffusion.

Sep 29, 2020